[Q] Captivate Not Booting - Captivate Q&A, Help & Troubleshooting

Hello,
I have been keeping up on these forums for awhile now and have learned it should be hard to brick the Captivate, well that's what i fear may have happened.
I hope you guys have ideas on how i can fix this, What happened is.
I followed the info from this tread here, http://forum.xda-developers.com/showthread.php?t=734871
I was flashing the I9000 rom to my Captivate, i have done a few roms before with out problems.
This time i flashed the rom from the US section and flowed the instructions on the I9000 rom and Odin3 did a reset to reboot the phone and that's the last time i seen anything on the screen.
So i thought it would be best to let it keep going and didn't touch anything, then Odin3 gave me the Green light and said passed but the screen was still black.
So i unhooked Odin3 and pulled the battery thinking maybe i just needed to reboot it, but nothing came back.
I have tried to put it back into download mode but have not been able to, its acting kind of like its not turning on now.
I have tried holding down volume up and down and inserting the usb cable after i put the battery back in but that does not work any more.
I have read that the volume buttons on the I9000 roms are backwards so i thought maybe that might be the problem but am out of ideas.
I hope you guys have some ideas, ill own any one a beer for help on this.

SpinDry2010 said:
I have been keeping up on these forums for awhile now
Click to expand...
Click to collapse
Not long enough to know this belongs in Q&A, apparently.

Yea sorry about that i was reading in that section didn't notice until after i posted.
So is it possible that the bootloader got jacked since i see nothing on the screen?

I have to question why you used a thread that was posted in July...
If you can't get into Download mode using any of the button combos, you'll need to make a Jig.
If that doesn't work, you're **** out of luck.

Jig? 10 char

Well the date of the thread does not seem to matter, but a Jig would only seem to work if i had a boot screen and just had flashed a crippled loader.
But looking into this further i found that the fing bootloader was packaged into the I9000 rom, now since that seems to be what i flashed i can see why that killed it.
I wish i would have known this before hand but i guess lesson learned unless some one thinks that should not matter.
I will have to send it back but i should be ok on that with ATT, but i will stay away from letting the Slb.bin stay in the flash next time.

Related

Disconnected from PC in the middle of Odin restore-phone wont' boot.

The USB cord was removed from my phone in the middle of an Odin restore (it was stuck at factoryfs.rfs). Now the phone won't boot and it isn't recognized by my computer when plugged in. Did I find a way to brick this thing? Any help would be appreciated. This is my fourth Captivate and I'm sure AT&T is going to start to give me a hard time. Thanks.
build a jig or buy one on ebay. you need to get into download mode and reflash to sotck.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139
http://forum.xda-developers.com/showthread.php?t=731989
Try all 3 methods to get into download mode first
yes, you can try the key combo first. but as i know, build 1010 or later wont work for the key combo.
Got it back to d/l mode. Now it's stuck at factoryfs.rfs-same as last time. I'm finished with this phone. AT&T can send me another. This is what happened to the past two phones. Stuck on a Odin restore and can't get it up again.
Edit: Just booted up. That's a relief. Thanks.
Thare187 said:
Got it back to d/l mode. Now it's stuck at factoryfs.rfs-same as last time. I'm finished with this phone. AT&T can send me another. This is what happened to the past two phones. Stuck on a Odin restore and can't get it up again.
Click to expand...
Click to collapse
If it had happened on more than one phone, you may consider looking at odin...maybe remove and reinstall our check your drivers or computer...just double check all of little stuff that might be so obvious that they are not obvious
********
Sent from my Samsung Captivate using the XDA app
ROM: Paragon RC5 1200 mhz/100hz kernel
so if your potentially bricking the phones, what do you tell AT&T that happened? and do they not ever check or whats the deal?
As far as I know at the wareenty centers they check for physical and water if they do attempt to boot as long as nothing looks custom they wont bother with checking the recovery or key combos samsung takes care of the rest they just want functional hardware..oh dont mention anything about modding. If anything syncing crashed is the best explaination. Tested.
Sent from my replaced cappy XD
Just dont become a familair face or it might get flaged on your account. Study up before doing somthing new. Just crashed my test cappy writing this had to stop and reflash heh live and learn.
A tech here on the forums said they can tell if it has been modified in just "3 clicks".
Sent from my SAMSUNG-SGH-IDK?
noobfail said:
A tech here on the forums said they can tell if it has been modified in just "3 clicks".
Sent from my SAMSUNG-SGH-IDK?
Click to expand...
Click to collapse
Lol....uh huh....i also have a direct line to the white house
********
Sent from my Samsung Captivate using the XDA app
ROM: Paragon RC5 1200 mhz/100hz kernel
Omg really?!
Sent from my SAMSUNG-SGH-IDK?
Just messin' around....what kind of tech? Att, samsung or other?
********
Sent from my Samsung Captivate using the XDA app
ROM: Paragon RC5 1200 mhz/100hz kernel
He said he was a manager of an actual at&t walk in tech support store.
I rooted a phone and flashed to stock and returned it with no problems.
Sent from my SAMSUNG-SGH-IDK?
Sorry I'm late getting back. My phone is up and running again. Got in to D/L mode and flashed back to stock. Got stuck on the AT&T logo, but used Odin one more time and it booted right up. The first time I brought in the phone, the tech took it to the display for 2 minutes and called the warranty dept for me. I think that it helped that the Chiefs playoff game was on. They didn't seem to want to be bothered! The phone rep asked about water and physical damage. No questions about modding. The second time I did it at home over the phone. Again, no questions about modding. I told the rep both times that I was trying to transfer music to the phone via Kies and it crapped out on me. It always help to play dumb and act like you don't know too much.
Thare187 said:
Sorry I'm late getting back. My phone is up and running again. Got in to D/L mode and flashed back to stock. Got stuck on the AT&T logo, but used Odin one more time and it booted right up. The first time I brought in the phone, the tech took it to the display for 2 minutes and called the warranty dept for me. I think that it helped that the Chiefs playoff game was on. They didn't seem to want to be bothered! The phone rep asked about water and physical damage. No questions about modding. The second time I did it at home over the phone. Again, no questions about modding. I told the rep both times that I was trying to transfer music to the phone via Kies and it crapped out on me. It always help to play dumb and act like you don't know too much.
Click to expand...
Click to collapse
I had the same exact problem when i was just starting to mess around with roms and my biggest issue was the sequence that it took to flash properly. i kept opening odin then putting my phone in download mode and THEN plugging it into use as opposed to how it should have been which is holding vol up and vol down pressed then plugging in usb.
bugity said:
I had the same exact problem when i was just starting to mess around with roms and my biggest issue was the sequence that it took to flash properly. i kept opening odin then putting my phone in download mode and THEN plugging it into use as opposed to how it should have been which is holding vol up and vol down pressed then plugging in usb.
Click to expand...
Click to collapse
That's the weird thing. I'm somewhat new, but have been flashing my Captivate since Sept. When the original Cognition came out I was flashing daily. I think my problem was, it took longer than usual to flash to stock, I got impatient and didn't realize I could get to D/L mode by taking the battery out, holding power and inserting battery. I always used the button combo. Live and learn.
same problem
Ok i have the same problem as the original post stated, running odin and disconnected right at the beginning of the rom flash! this phone wont power up, and my jig (which i have used before) will not work! Is it done for!?
Ur last hope lays in adams Am I bricked thread, where u'll find an app that checks what state ur phone is in (linux or ubuntu needed)
nevermind, I tried harder and the jig worked, its one of the homemade jigs, where you cut up your charger, and use resistors to create the circut . . . . jankety but i got it to work thanks anyway though
Glad you got it, but I would buy a jig and keep it in a drawer. Just in case.

[Q] In a LOT of trouble!

So a few days back i flashed the serendipity VII rom on to my previouly 2.2 Cappy, and it worked like a charm... a day later i was experimenting with a few ROMS all 2.3, and they worked, and to my luck I flashed a 2.2 ROM (Cognition 4) (by mistake i might add) and there it was a complete black screen brick!
since then Iv tried various methods to bring it back to life, the 3button thing, the taking the battery out holding down the 3 buttons connecting the usb and putting the battery back in, then releasing power only... Iv tried to even get it JTAGed, which was a disaster since the JTAG guy tried and cudnt get the thing to show connectivity... ANY HELP??
I fail to accept that this is the end... Please HELPP!!!!!
just keep trying to get into dl mode by using other usb ports, a jig, holding buttons while battery removed and install battery then plug in phone, happened to me plenty of times but was persistant that it finally got into dl mode.
Try making a jig and putting phone in download mode then flash stock through odin -- do a search for jig in the captivate forums. It saved me many times. You can even make one for about $1.
If you had gingerbread then you may need to use the i9000 version of entering download mode. The key combination is different. Search around on the forum as plenty have already mentioned what it is. I just don't remember off the top of my head.
if it will not power on at all....it doesnt look good.
try holding volume down and power...see if that brings up download mode. a jig is only $8 shipped to your home and will work.
i had a similar scenario and a jig brought my cappy back to life!! ive had the same phone since september, the jig has saved me from at least 8 new phones
I have seen a black screen for download mode. The only way I knew I was in download was when I saw the yellow band appear in Odin. Open Odin, and try different button combinations that will get you into download mode until you see Odin recognize your phone.
I'm sure you've tried, but these are 2 other key combos. I've had that happen to me in the past and it can be frustrating.
1. volume up + volume down
2. volume down + power
3. volume down + home (softkey) then power (this is the one that worked for me)
4. volume down + menu (softkey) then power
Hope everything works out for you. If all else fails, I'm sure a jig will work.
I learned this in the days of old, when we were flashing the baked Froyo's. Don't know if it applies or if you've tried it already, but what used to work for me was:
Open Odin
Pull the battery out, put it back in...don't turn it on.
Hold the volume down button
Plug in the usb
At no point in the process should you ever touch the power button. For your Odin version, I'd recommend using the Stock Odin, get factory and then try flashing your custom Rom again.
(Edit: I say volume down because that's the current button to enter download mode with Gingerbread. It used to be Volume Up and Down at the same time.)
ok first this does not belong in the dev section! belongs in Q&A so thing will get closed pretty soon. also other than a correct jtag u cant recover with jig, button combo or voodoo magic. u just mixed a i9000 GB bootloader along with a captivate froyo secondary boot which the Cog4 ROM has. use search and i think you can find someone who offers a jtag service
Well, I've seen a few mention it, but I think your going to need to make or puchase a jig. Hit radioshack and get 3 100kohm resistors, about $1. The directions are all over the forums here. I'd be willing to bet that will fix you up.
Also, once in a while it may still be alive even though the screen is black. Like someone else said, go ahead and start Odin, then plug your phone into USB. See if there is any response from Odin. It's worth a shot.
Either way, it's good to have a Jig handy.
claim warranty.
Odin 1 click to stock then start from scratch!
EsotericSYN said:
Odin 1 click to stock then start from scratch!
Click to expand...
Click to collapse
you need dl mode to do that, he's not even getting power up. go to att store and say it wont turn on today gimme replacement.
How did someone with just 2 posts make a thread in here? I thought you had to have 10+ posts just to post in a thread.
just contact samsung the captivate should be in warraty untill oct2011.. i also bricked my phone while on serendipity VII see Q&A Soft brick or hard Brick.i had my phone stuck on the battery charge screen. was not able to get to download mode or recovery and my battery wouldnt charge . so i called samsung just gave them my imei number and they said it was under warranty until oct 2011. i did not tell them i bricked it while flashing roms. i just told them my phone wont charge or turn on. i sent my phone to the samsung repair center in dallas tx. my phone was fix at no charge even though i had it rooted and running a custom rom. samsung just fixed my looping battery screen and put there stock froyo erasing all my apps and data.it took about 2 weeks to get all this done. got my phone back this monday and everything is working great....
so just contact samsung and say the phone wont turn on dont say you rooted it or flashed a room. samsung wont check to see if its rooted all they care about is that you didnt drop the phone or something like that.
cremefraiche said:
ok first this does not belong in the dev section! Belongs in q&a so thing will get closed pretty soon. Also other than a correct jtag u cant recover with jig, button combo or voodoo magic. U just mixed a i9000 gb bootloader along with a captivate froyo secondary boot which the cog4 rom has. Use search and i think you can find someone who offers a jtag service
Click to expand...
Click to collapse
listen to this man
Same exact thing happened to me on my last phone. Your phone is dead, dead, dead. Hard bricked. Nothing will bring it back. Take it to an AT&T store and tell them you were upgrading to 2.2 and the screen went black and now it wont come back on.
There is no jig or JTAG that will fix it, trust me, I tried
timbrendelaz said:
Same exact thing happened to me on my last phone. Your phone is dead, dead, dead. Hard bricked. Nothing will bring it back. Take it to an AT&T store and tell them you were upgrading to 2.2 and the screen went black and now it wont come back on.
There is no jig or JTAG that will fix it, trust me, I tried
Click to expand...
Click to collapse
at&t might help, but you have to hassle alot.Just contact samsung they will help for sure.i just sent them my bricked phone and they fixed it in two weeks at no charge. samsung will do it for free, im living prof.
I dont really buy into the fact that its dead, no way... its just that the revisions on the boot.bin and sbl.bin are different... shouldn't JTAG work? and cant claim warranty cuz im not in the US!!! there must be a way people.... im faar too poor to just give up without a fight!!!

Can't get into recovery/dload mode Phone boots to white At&t screen makes few sounds

Can't get into recovery/dload mode Phone boots to white At&t screen makes few sounds
I have recently messed up my Captivate when I was trying to flash a ROM. My phone goes up to the white At&t sign and then makes a few sounds and stops. It also goes to the charging screen when plugged in the cpu when off. I have tried countless ways to get it to go into dl mode or even recovery mode. Ive tried: ADB vol up and down plus power with usb plugged in/battery put in, vol down usb plugged in/battery put in, vol up usb plugged in/battery put in, just vol up and down usb plugged in/battery put in, and nothing seems to be working. WITHOUT someone tellin me to use a jig can ANYBODY please help me find a way to do this. I have even pressed menu and volume down while the phone was in off charging state with green bar loading and the cpu made a sound and cpu said unrecognized device...from there I have tried to root my phone hoping it goes into recovery mod(which ive done to fix my phone before) also from there i have tried odin but no recognizance and I also have tried adb reboot download and adb reboot recovery. NOTHING WORKS...someone please HELP ME!
thanks in advance
What rom were you trying to flash?
why SO resistant to someone telling you to make/buy a jig? its a very easy thing to make and it will solve your no download mode issue in seconds. if nothing else will get you in download mode a jig will for sure (unless your usb port is broken) you can try and exhaust all other solutions but after you've ripped all your hair out build a jig.
its like trying to dig a ditch with a garden spade when you have access to a back hoe
Good point
stud u really make a goop point about it being easier to buy a jig than to pull ur hair out. Which if this kid really was pulling his hair out he shouldn't have been doing this at all. But, I am also having this same problem. I was using a CM7 build and it worked great until i tried to install the gapps. then it went crazy. It rebooted itself and went through the Cyanogen Mod first screen then would get stuck on the CM7 blue android on skateboard bootscreen. If I touched the screen at the bottom right it would vibrate for some reason. Shortly after realizing I needed a jig for it I decide to buy a new one cause at the time I didnt know if I could properly make one. So I've kept my first captivate still trying to find a non-jig method. I recently taught myself begginers adb on Windows XP OS but I am very much a noob except for rooting and flashing. Any help of yours would be great anytime. Thanks,
Matt
gujuplaya111 said:
NOTHING WORKS...someone please HELP ME!
thanks in advance
Click to expand...
Click to collapse
Shows that youve been a member since Dec-2010 so Im assuming that you really did try everything because you have read and read and read (riiiiiiight!?) and without telling us whether you tried to flash a Froyo or Gingerbread ROM I'd sugguest that you buy a JIG. Its really the best solution and the less time consuming if you cant think of anything else to try. You can order one or make your own...literally took about 30 minutes for me to get my phone to a place where i can work with it....a trip to the radioshack and making the JIG and back home.
If you are making requests on specifically NOT to tell you to do it a certain way then you may have to accept that you might have to solve this problem on your own, especially if you said that you tried everything except the one thing that you cant do (which is what we might suggest) and probably will fix your situation.
So i re-read after making my first post to this. I've bought my 5th Cap. now and have quite a bit more knowledge than before. So my question is. If I've completely bricked my 3rd cap... No battery charge screen and all will a jig still work for me to get into download? I was tryin to come back from cm7 but something went wrong.... I really don't need the extra phone but it would be nice to have my back up
Sent from my SGS Captivate on Cog. 5 v2 using XDA Premium App
dm63755 said:
So i re-read after making my first post to this. I've bought my 5th Cap. now and have quite a bit more knowledge than before. So my question is. If I've completely bricked my 3rd cap... No battery charge screen and all will a jig still work for me to get into download? I was tryin to come back from cm7 but something went wrong.... I really don't need the extra phone but it would be nice to have my back up
Sent from my SGS Captivate on Cog. 5 v2 using XDA Premium App
Click to expand...
Click to collapse
If the screen doesnt turn on at all and there is no charge screen or recognition at all of usb than it is more likely then not hard bricked.
Sent from my i897 running MIUI 1.8.12 with TalonMTD kernel.
Thanks xijar then i will for sure purchase a jig. Worth a try anyway.
Sent from my SAMSUNG-SGH-I897 using XDA App

[Q] PROPERLY BRICkEd SAMSUNG GALAXY S I9000's ONLY - (no screen response)

hi iv had a serious journey with my sgs i9000 here's how it goes:
i had it on 2.2 and then upgraded it officially to 2.3.3
not much else happened until i realised i wanted voodoo sound (apparently it was hyped to be awesome....its not that great) and neither is the ext4 file system 2.3.3 seems to be just as fast...dont know if it was a major problem on 2.2 but it aint really on 2.3.3
so i flashed voodoo on 2.3.3 from some website ... downloaded the app for the sound as the kernel didnt support that...
then i was using it and played around with the settings in clock work manager and i mounted and unmounted sd/card i dont think it made much difference but i thought i'd mention it ... the reason i did this is because when i tried to load a rom it wouldnt find all my sd card files beyond like the first 5 folders so i thought i'd give it a kick start....
then what happened is the phone just went off and i couldnt get it back on.... little did i know this was soft brick... i didnt know why....
i got the computer screen with the phone and exclamation mark.... i got into download mode a few times....
NOW .... i cant get it to turn on AT ALL using any combo buttons....
i think the nail in the coffin was flashing it with the "one-click odin" which was for the captivate but it said i could use it on the i9000 too.... which blatently screwed up the device....
anyway iv ordered a jig device... if this gets me into download mode ....what am i supposed to do...?
also is there anything i can do to get it into download mode now ? (bearing in mind iv done all the combo's ... some people say leave the battery out for a couple of minutes or half an hour....)
i think the bootloader is screwed up because it doesnt switch on....
even after i did a clean install of 2.3.3 with the pda phone and csc roms... it still just randomly switched off after 2/3 minutes of boot time....
what do i do now ?
samsung repair centre said they couldnt do anything and i'd have to send it back to samsung.... is it that bad?
Tried all the combos.... So you tried plugging in combo, then battery and also holding combo and then battery without cable in...
Have you read the pinned thread in general i think it is regarding, bricks?
Moving on
how did you do a clean install of 2.3.3 if you couldn't get DL mode??
Haven't read into the one click Odin so can't comment on that, but i think that was meant to be for softbricks...
anyway regarding the jig, just plug it in, and then wait a second or so, of not a minute (usually instant) and it should go into download mode. If it doesn't work again try some combos with the jig in...
If it is a hard brick i think you need to J-tag it, or yes take it to samsung in which case they may charge you for a repair, unless you say kies did it, and you didn't tell them everything you didi when you spoke to em.
Think thats everything lemme know if i missed out a question of yours or you want something better explained etc..
yeah i guess i was vague on the combo thing...
i've tried:
a) holding power, menu and volume down while sliding battery in (no usb cable in )
b) same as above with usb cable in
c)just menu and volume down buttons while i put battery in
d) both volume buttons and cable in
e)both volume buttons and battery in
.... the reason for d and e is because when i flashed it with the one click odin installer thing.. it restarted and showed a a t&t screen so i think its flashed the software with a samsung capacitive rom....so in theory i need to use those buttons ? not sure .... yet more questions....
i just hope this jig thing works ... btw do i have to pay sammy is my phone is under warranty?
how do i reflash the bootloader so it works properly? is that even the problem? do i need to do that? which pit file do i use ? some people say 512.... some say thats outdated and the new pit file is the thing to use .. ?
Talon26 said:
Tried all the combos.... So you tried plugging in combo, then battery and also holding combo and then battery without cable in...
Have you read the pinned thread in general i think it is regarding, bricks?
Moving on
how did you do a clean install of 2.3.3 if you couldn't get DL mode??
Haven't read into the one click Odin so can't comment on that, but i think that was meant to be for softbricks...
anyway regarding the jig, just plug it in, and then wait a second or so, of not a minute (usually instant) and it should go into download mode. If it doesn't work again try some combos with the jig in...
If it is a hard brick i think you need to J-tag it, or yes take it to samsung in which case they may charge you for a repair, unless you say kies did it, and you didn't tell them everything you didi when you spoke to em.
Think thats everything lemme know if i missed out a question of yours or you want something better explained etc..
Click to expand...
Click to collapse
ok now iv got it to turn on quite regularly .... but it keeps cycling (bootlooping) the at&t logo screen .... cant get into download mode or recovery mode.... just keeps boot looping.... oh and when i plug in the usb cable it just turns off.... its like i cant start it up with a usb in the phone...
update: been reading around and if anyone has this problem.... it looks like you might be hard bricked and apparently this cant be resolved via jig device..... dammit ...i'll still try and update the post... peace
So you haven't tried the jig yet?? because you haven't got it yet right
I don't think the device is bricked at all. Bricked usually means you have no response from it, so no matter what combo, actions you take you get no reaction.. However you are getting a boot although there is something going wrong as it does so...
So yes you need a new bootloader, i think every rom that you flash through odin has one, but i guess it may not, its best to search this, but i have read a few posts that say you need to click on update bootloader (i would check into this, as if this is wrong it will definitely brick your device)
My suggestion is go back to the onclick odin thing as that should do it, im sure someone has done something similar.
Yh so to sum up, i would have high hopes for a restoration (but what so i know ) and yes flashing a new bootloader with rom i reckon would do the trick. I think a stock rom will do it. Click on the stock rom link below and type in a few search terms in that thread to see if you pick up anything otherwise do a slightly wider one of the forum.
Talon26 said:
So you haven't tried the jig yet?? because you haven't got it yet right
I don't think the device is bricked at all. Bricked usually means you have no response from it, so no matter what combo, actions you take you get no reaction.. However you are getting a boot although there is something going wrong as it does so...
So yes you need a new bootloader, i think every rom that you flash through odin has one, but i guess it may not, its best to search this, but i have read a few posts that say you need to click on update bootloader (i would check into this, as if this is wrong it will definitely brick your device)
My suggestion is go back to the onclick odin thing as that should do it, im sure someone has done something similar.
Yh so to sum up, i would have high hopes for a restoration (but what so i know ) and yes flashing a new bootloader with rom i reckon would do the trick. I think a stock rom will do it. Click on the stock rom link below and type in a few search terms in that thread to see if you pick up anything otherwise do a slightly wider one of the forum.
Click to expand...
Click to collapse
jig arrived today! .... i plugged it in ..... NOTHING ..... (read on theres more to the story!!!)
so i put it in nothing happened...... i thought maybe the jig device was not working so i tried it in the i9100 (s2) .... WORKED ...!
im really stubborn so i needed to make mine work too..... i read in a review of the jig device that someone bought one and it hadnt worked .... i hadnt ruled that out
anyway all day i just kept trying to jump start it by putting in the wall charger in and out ... i usually get some reponse from that....nothing apart from a second of something like a loading circle......
anyway then i left it on charge for an hour ....maybe the battery was dead and then tried again ....
(btw i was getting no response at all at this stage, not even the at&t thing ...)
so it was pure black screening me.....
then i got home from work and thought let me exchange the battery and see what happens....
i changed the battery and put the jig device in ...... VOILA !!! download mode....
all is well so far i've flashed with 2.3.3 pda,phone and csc files and checked repartition... i haven't messed with the bootloader option
seems to be working ok....also gave it a restart too ... last time it got to this point but it didnt turn back on after a restart ....
in conclusion .... charge battery fully externally (putting the power in the phone in this state was not charging it)
then with a full battery put jig in .... if that doesnt work you phone might be seriously bricked.... bravo to whoever dreamt up the jig device
Glad to hear the great news!
Nice
Thanks for this useful info

[Q] I messed up. Can get into download mode that's all..

I hope someone can help me here, I'm posting with the belief that this may be a simple enough problem (With the hope).
I tried to install a Custom Recovery on my Galaxy S using this tutorial - wiki.cyanogenmod.org/w/Install_CM_for_galaxysmtd
I managed to get to step 6, and a blue bar appeared, but then i could not do step 7.
Now i cannot boot into recovery mode, nor will the phone boot past the Samsung Galaxy S logo.
I can still get into download mode, but Odin does not detect the phone.
. I have changed cable and tried different versions of Odin..
When i turn on the phone normally it shows the Samsung Galaxy S logo, blinks, and then reboots and does the same.
When i try to enter recovery, i get the same, unless i connect it to the PC. I then get an 8 pointed star, like the loading flash circle thing - the same as a flash video loading except it does not move.
I have also removed the battery and tried to enter recovery and download mode while inserting the battery.
I have removed the SIM and battery for a few minutes.
when i try to start Zadig, with the phone connected in Download mode, i get "Gadget Serial" as the device connected. I used to get "Samsung USB Composite Device"
I have tried many different things and read over the recommended threads on this forum. I think i need a bit more pointing in the right direction.
I really hope somebody can help me. I am very worried that i may have bricked it.
Thank you.
Try this:
This feature is great for people who
a) Have a bad KIES flash
b) Stuff up their phone somehow
c) Accidentally flash something dodgy via ODIN
d) Some other random occurence
To test this feature you just need to start with your phone turned off... Best way to be sure is to remove the battery.
Then
1. Put battery back in
2. Press and hold Volume Up + Home Key
3. Continue holding those buttons and then press and hold power button.
4. When you see the logo pop up release power button ONLY
5. Keep holding two buttons from step 2 until you enter recovery mode.
I hope this helps?
Also have you tried everything on this thread:
http://forum.xda-developers.com/showthread.php?t=1134975
akash6969 said:
Try this:
This feature is great for people who
a) Have a bad KIES flash
b) Stuff up their phone somehow
c) Accidentally flash something dodgy via ODIN
d) Some other random occurence
To test this feature you just need to start with your phone turned off... Best way to be sure is to remove the battery.
Then
1. Put battery back in
2. Press and hold Volume Up + Home Key
3. Continue holding those buttons and then press and hold power button.
4. When you see the logo pop up release power button ONLY
5. Keep holding two buttons from step 2 until you enter recovery mode.
I hope this helps?
Also have you tried everything on this thread:
http://forum.xda-developers.com/showthread.php?t=1134975
Click to expand...
Click to collapse
I hadn't seen that thread, but i have gone over tons of them Thanks for reply.
I eventually got Odin to detect it and I tried this - http://forum.xda-developers.com/showthread.php?t=1544487
It came up red and said failed.
I closed odin and disconnected the phone. Now i can't even turn it on.. Nothing. I am hoping the battery died, and it's a coincidence..
No response at all to any buttons... I haven't done anything else.
If i can get it to power up again, i'll try those tips.
Tomato_Jam said:
I hadn't seen that thread, but i have gone over tons of them Thanks for reply.
I eventually got Odin to detect it and I tried this - http://forum.xda-developers.com/showthread.php?t=1544487
It came up red and said failed.
I closed odin and disconnected the phone. Now i can't even turn it on.. Nothing. I am hoping the battery died, and it's a coincidence..
No response at all to any buttons... I haven't done anything else.
If i can get it to power up again, i'll try those tips.
Click to expand...
Click to collapse
Ok, Don't worry, Charge your phone battery to 100%, leave over night. ( keep charger connected to your phone overnight)
Best to have a fully charged battery in these situations!
Keep calm, and read and prepare what you want to do next.. Don't try everything in a frantic effort to get your phone started again.
I know it's difficult, but there are lots of threads on how to rectify most problems.
I wish you Good luck!!
sorry to ask some stupid question, but can u make sure what versiom ur fone is?
is it i9000?, or i9001 or i9003? or korean anycall? as far as i know, flashing i9000 ROM to i9003 will hardbrick da device.
Sent from my GT-I9000 using xda premium
akash6969 said:
Ok, Don't worry, Charge your phone battery to 100%, leave over night. ( keep charger connected to your phone overnight)
Best to have a fully charged battery in these situations!
Keep calm, and read and prepare what you want to do next.. Don't try everything in a frantic effort to get your phone started again.
I know it's difficult, but there are lots of threads on how to rectify most problems.
I wish you Good luck!!
Click to expand...
Click to collapse
Thanks.
This is a disaster. I tried to power it on to any mode there before i saw your post.
I needed to update the phone, because an app i needed for studying was only available on Android 4+.
Now no phone..
I saw a few threads, i hope after i leave it overnight i'll be able to power it.
If not, probably a JIG?
I don't fancy making one, but if i have to, i guess i'll give it a try. I don't think i could wait a week or more for a premade one to be delivered.
Anyway, for now, i'll keep my fingers crossed.
Thanks for help/tips and reply.
I'll post back tomorrow, hopefully with some better news.
Tomato_Jam said:
Thanks.
This is a disaster. I tried to power it on to any mode there before i saw your post.
I needed to update the phone, because an app i needed for studying was only available on Android 4+.
Now no phone..
I saw a few threads, i hope after i leave it overnight i'll be able to power it.
If not, probably a JIG?
I don't fancy making one, but if i have to, i guess i'll give it a try. I don't think i could wait a week or more for a premade one to be delivered.
Anyway, for now, i'll keep my fingers crossed.
Thanks for help/tips and reply.
I'll post back tomorrow, hopefully with some better news.
Click to expand...
Click to collapse
Sorry to say, most likely you will need a USB JIg to fix the problem you have. :/
If you linked the correct page when you said you tried to do this- and if I opened the correct page, that takes you to an SII section. Those are SII firmwares, not for the S.
So as compacity said, please clarify what device you have... Whether its an I9000 (galaxysmtd is for the I9000) or an I9100 (the firmware page you linked). If you do have an I9000, then your brick comes from flashing a different device's rom onto the S, which would give this error in Odin beause its incompatible.
In this case, you'd probably need a USB Jig to come out of it.
Try what the others said and hopefully you'll be at least able to enter Download mode before resorting to a jig, but considering your situation, I have to say realistically a jig is your best bet :/
Sent from my GT-P7510 using Tapatalk HD
You need a usb jig. It will get you into download mode. Now you need to flash cf root, which will come with cwm recovery. Recovery mode should work now. If you get computer!phone, then re-flash cf root. Now you should be able to flash CyanogenMod via cwm recovery. Thank if I helped!
Sent from my GT-I9000 using cm10.1
Soryuu said:
Sorry to say, most likely you will need a USB JIg to fix the problem you have. :/
If you linked the correct page when you said you tried to do this- and if I opened the correct page, that takes you to an SII section. Those are SII firmwares, not for the S.
So as compacity said, please clarify what device you have... Whether its an I9000 (galaxysmtd is for the I9000) or an I9100 (the firmware page you linked). If you do have an I9000, then your brick comes from flashing a different device's rom onto the S, which would give this error in Odin beause its incompatible.
In this case, you'd probably need a USB Jig to come out of it.
Try what the others said and hopefully you'll be at least able to enter Download mode before resorting to a jig, but considering your situation, I have to say realistically a jig is your best bet :/
Sent from my GT-P7510 using Tapatalk HD
Click to expand...
Click to collapse
huskyT said:
You need a usb jig. It will get you into download mode. Now you need to flash cf root, which will come with cwm recovery. Recovery mode should work now. If you get computer!phone, then re-flash cf root. Now you should be able to flash CyanogenMod via cwm recovery. Thank if I helped!
Sent from my GT-I9000 using cm10.1
Click to expand...
Click to collapse
Both helped a lot, thanks.
I had to end up bringing the phone to a repair shop
Something i am not inclined to do if i can avoid it. Especially if i caused it, i would hope i could undo it. But because i need a jig, and i wouldn't have time to get one or make one before Monday, i had to bring it to someone else.
I am buying the materials for a jig, and maybe going to buy one also, for future.
 @Soryuu - Yep, i linked to the page, so i must have flashed the wrong firmware.
I'm angry with myself because i read everything else carefully. I had been reading all day. I guess i was just tired and thought I had got to the final hurdle. I was careless.
@huskyT - Thanks, will know that for future reference. I have two old Android phones somewhere. One is a Galaxy Europa, and one is an LG (not sure what model). Both are borked in some way, but i could probably use them for practice. I think the Galaxy Europa is flashed badly. Not by me. (Thankfully).
Tomato_Jam said:
Both helped a lot, thanks.
I had to end up bringing the phone to a repair shop
Something i am not inclined to do if i can avoid it. Especially if i caused it, i would hope i could undo it. But because i need a jig, and i wouldn't have time to get one or make one before Monday, i had to bring it to someone else.
I am buying the materials for a jig, and maybe going to buy one also, for future.
@Soryuu - Yep, i linked to the page, so i must have flashed the wrong firmware.
I'm angry with myself because i read everything else carefully. I had been reading all day. I guess i was just tired and thought I had got to the final hurdle. I was careless.
@huskyT - Thanks, will know that for future reference. I have two old Android phones somewhere. One is a Galaxy Europa, and one is an LG (not sure what model). Both are borked in some way, but i could probably use them for practice. I think the Galaxy Europa is flashed badly. Not by me. (Thankfully).
Click to expand...
Click to collapse
Don't stress mate, we all have bad days, we all make mistakes
Sent from my GT-P7510 using Tapatalk HD
Well....
I would have been quicker if i had ordered a jig and done it myself.. (Worth mentioning, i had told guy in phone shop what happened, and about the required "jig")
I collected my phone from the shop today, after a week, and i was told "Your phone is f*****d". To which i replied, "what? are you sure, i mean, i have only flashed it with SGS2 firmware, i'm under the impression it is very hard to break/brick, if i have a jig."
He told me, "Nope, it's beyond repair, it won't work. If you want, i can use the screen and other parts, i'll buy it off you for €40"
No thanks.
So now i am on the lookout for a premade jig. Does anybody know where i can buy one?
I meant to last week, but things happened, and without a phone i was running around a bit...
I'm going to check ebay, but if somebody could recommend somebody reliable, i'd prefer that. Thanks.
I bought it from ebay, no problem...but just saw a couple of minutes ago that also on amazon germany these jigs are offered now/in the meantime....
rodman01 said:
I bought it from ebay, no problem...but just saw a couple of minutes ago that also on amazon germany these jigs are offered now/in the meantime....
Click to expand...
Click to collapse
Thanks.
I bought a jig, and it arrived today. Have phone in charger.
Do i just plug the jig in?
Or do i also do the three button press?
The screen is completely black, and nothing appears on it.
only plug the jig in, thats all... phone will start in download mode of its own. :fingers-crossed: :fingers-crossed:
rodman01 said:
only plug the jig in, thats all... phone will start in download mode of its own. :fingers-crossed: :fingers-crossed:
Click to expand...
Click to collapse
Thanks, going to leave it charging for a little longer, and try it.
If it doesn't work, would a motherboard for the Samsung Galaxy S be easy to replace? I have found one unlocked for €25.
EDIT
Found a tear down video here - http://www.youtube.com/watch?v=vxPWsLd05F4
yes thats not so difficult...only thing a bit complicated is to open the back or middle cover...but there are a few movies on youtupe where you can see how it can be opened and dismounted....btw for the first try with the jig battery has not to be that full...only if it starts in download mode and you can flash it via odin I would recommend to charge it complete.
rodman01 said:
yes thats not so difficult...only thing a bit complicated is to open the back or middle cover...but there are a few movies on youtupe where you can see how it can be opened and dismounted....btw for the first try with the jig battery has not to be that full...only if it starts in download mode and you can flash it via odin I would recommend to charge it complete.
Click to expand...
Click to collapse
Thanks again.
I am after removing it from the charger, and inserted the jig. It's in about 30 seconds now, and nothing is happening..
that sounds not good...ususaly it takes only a few seconds or perhaps a minute till it starts to download mode....sorry for no better news....
rodman01 said:
that sounds not good...ususaly it takes only a few seconds or perhaps a minute till it starts to download mode....sorry for no better news....
Click to expand...
Click to collapse
What seems to have happened, is i tried to flash it with SGS2 rom. So is it unbrickable?
I am not sure but I think that minimum the bootloader is damaged...there is one more possibility: to repair it via jtag...but for this you have to find someone, who ones one and can repair it....some of the guys don't take much money for such a repair, but with transport costs ets...perhaps it would be cheaper and faster if you take the new mainboard you mentioned.

Categories

Resources