[Q] Botched Gingerbread install - Captivate Q&A, Help & Troubleshooting

So, I went to install gingerbread on my captivate, ripped from the nexus s, but I accidentally flashed the wrong thing. now my phone turns on to the att logo, then it goes away, then about 20 seconds later it comes back. I have been looking for hours on how to get to download mode, and I think that somehow I crippled my chances of using the 3 button combo. I know how to use abd to get to download mode, and my computer shows that my phone is connected when I plug it in at the att logo, but, my PC thinks its a nexus s and it can't find drivers for it. I updated my SDK but it still wont find drivers. is there anyway to install nexus s drivers or to get my phone into download mode without a jig?

Just take the battery out and plug in usb cable while holding volume up and down. (I had the same problem until someone suggested this)

that didn't do anything. if it matters, my phone wont even get to the battery charging screen with the usb cable plugged in, the spinning circle thing comes up for about 2 seconds, goes away, then comes back but its frozen the whole time, nothing else happens. My PC still sees that its plugged in, but, like I said, it thinks its a nexus s, and wont install drivers :/
PS: as to exactly what happened, I forgot to do the voodoo lagfix before trying to install the gingerbread dump from the nexus s, so I got into download mode and went back to 2.1. it was right after that when I realized that my three button combo wasnt working, so I was going to fix that by updating the bootloader, but accidentally loaded nsongs.tar instead of the tar that would fix my download mode combo, so in Odin, I had phone bootloader update checked when I flashed that

tortugasthebest said:
Just take the battery out and plug in usb cable while holding volume up and down. (I had the same problem until someone suggested this)
Click to expand...
Click to collapse
i had a successful install.....but my problem came when trying to revert to stock.
PC wouldn't recognize device and for the first time ever i couldn't get into download mode using method above or a 3 button method that worked for me (a slight variation to method stated above).
Finally the following worked:
1. open odin 1-click JF6
2. remove battery (and any external sd) from phone
3. plug phone into pc via USB (without battery in phone)
4. Hold Vol + / - toggle down simultaneously.
5. While holding the buttons down insert the battery. When i did this my phone entered DL mode almost immediately and i was able to use odin to get back to stock.
build 1007

I'd try the above method to get into DL mode.. if that doesn't work you can try the JIG and see if that works.
But a requirement before flashing was to verify that your buttons worked on your phone.

the buttons were working, but I didn't have a lagfix installed. I flashed back to stock and noticed that my buttons weren't working after that. I went to fix them but flashed nsongs.tar by accident, and I had the "phone bootloader update" box checked, so I'm thinking thats why my buttons aren't working now. I've tried that method above a couple times and nothings happened...

Hmm.. you can try and update using the Nexus S USB drivers.. if they are different from ours that is .. go to that forum and poke around to look for them.
At this point.. can't hurt trying anything.

Where would I find the nexus s drivers? I installed the samsung mobile phone drivers, but my computer still says "found new hardware - nexus s" anytime I plug in, and it shows up in device manager with a big yellow question mark.

avgjoegeek said:
I'd try the above method to get into DL mode.. if that doesn't work you can try the JIG and see if that works.
But a requirement before flashing was to verify that your buttons worked on your phone.
Click to expand...
Click to collapse
same as the poster
when i did my install my buttons were working as well....i have the 1007 build and never had any problem getting to recovery or dl using 2-button and 3-button combo's.
After the gingerbread flash was a different story though. Luckily for me the method i posted almost like jumpstarted me into DL mode....when i did that it went into DL faster than it ever had with the normal methods....the DL screen popped up almost the instant the battery connectors hit.

yea, none of the methods I've found have gotten me into download mode. Is there anyway to get the nexus s drivers so I can do this through adb? I don't have a car so getting to radioshack to buy resistors is kinda hard :/

ok, so I updated my sdk again and it now I have the drivers installed, I can use adb now, but whenever I do, adb reboot download, it reboots, but not to download mode, i goes right back to the boot loop. I was wondering if there was anyway to push a new bootloader onto my cappy using adb. that would be awesome

Related

[Q] Phone is a brick after deleting framework-res, help?

K so like an idiot i deleted framework-res, and now my phone turns on to a black screen. I've tried to reflash it with odin and odin 1 click, but it always gets stuck at "file analysis". I don't get why because I used odin 1 click to install froyo in the first place so I know it works.
Anyway, I have no idea what to do, as I can't get any files on or off my phone because ADP will always say the device is not connected.
if its stuck at file analysis keep fiddling until it goes past that for instance plug in into download mode with it open and then unplug and replug it in. just keep trying.
i've been trying for hours... rebooting.. reinstalling.. everything. it won't get past File Analysis...
Are you trying to use the odin 1click to flash back to jf6? That might work.
Sent from my SAMSUNG-SGH-I897 using XDA App
droidal said:
Are you trying to use the odin 1click to flash back to jf6? That might work.
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
nope, still hangs at File Analysis
i have done the same and now back up i used an old odin to go back to original stock and then updated to froyo after. If you can use sdk adb reboot recovery and fromat your sd card then try odin again this worked for me
maybe try restarting computer. make sure you dont have anything adb related running. pull battery. start odin one click. put battery back in. hold vol-up and down at same time(just the vol. buttons no power) plug in usb from comp. to your phone while you still have the vol. buttons held. should be in download mode. click start.
and if you wanna try pushing a new framework, i guess you could try to boot into recovery and adb should see it then as debugging mode is auto on in recovery mode. let us know.
sbtim said:
K so like an idiot i deleted framework-res, and now my phone turns on to a black screen. I've tried to reflash it with odin and odin 1 click, but it always gets stuck at "file analysis". I don't get why because I used odin 1 click to install froyo in the first place so I know it works.
Anyway, I have no idea what to do, as I can't get any files on or off my phone because ADP will always say the device is not connected.
Click to expand...
Click to collapse
Are you using 64 bit Windows 7? I am and had a similar problem. On my original attempts to flash my phone with earlier versions of Cognition, I learned that if you don't disable the lagfix, you can have a problem. Assuming you used one I hope you disabled it. I also used odin 1-click at the time and it didn't work terribly well, mostly due to the voodoo lagfix ext4 filesystem.
Secondly, I've also found that it's best to go into download mode using the following method:
I do a battery pull, remove sim and sdcard (if you have one), put battery back in. Make sure your USB cable is plugged into a USB port on the motherboard, not one of those front USB ports (they sometimes don't get enough juice, you wouldn't want the device to disconnect in the middle of a flash). Hold volume up/down and plug in the USB cable. Odin one click should recognize the phone is hooked up to a COM port. At that point, you click the start button and it flashes. It should not take more than 1-2 minutes to flash. If Odin looks like it it is not working, rather it sits at Verifying or does not actually move at a brisk pace, it's not going to work. You can let it sit for hours and it will never flash. If this happens, do the battery pull and try again. My first time doing this was rather nerve wracking as i thought i bricked my phone. Had the screen with the phone/exclamation mark/computer and the computer did not detect my phone via USB. I've seen people who say reinstalling the Samsung drivers or rebooting the computer or switching USB ports might help as well.
Ever since i figured out the above, i've been able to flash my Captivate on Win 7 64bit without a hitch. Currently running the latest build of Cognition 2.2 and loving it.
I've done all of the above and Odin hangs on Verifying, ADB gives the same error message on every "ADB" command : "error: device offline: (while in recovery mode)
My computer/Odin does recognize that it's plugged in, but it won't mount and let me into the SD card or format it, etc.
edit : fixed
weee
sbtim said:
edit : fixed
weee
Click to expand...
Click to collapse
You should post what you did to fix it in case someone has the same issue
Sent from my SAMSUNG-SGH-I897 using XDA App
Yes he should.
What did you do to fix it? Do tell.
10 bucks says he succeeded once he read the directions properly.
Reading is hard, that is why so few people do it.
Same exact thing happened to to me 2 days ago. All I did was:
1)take the battery and SIM card out, wait a few seconds,
2)run Odin3 on my PC and hookup the USB cable to the phone while still off
3) hold both Volume buttons down while phone is off and connected
3)at the same time, slide in the battery with 1 finger or have someone do it
4)keep volume keys held down as the battery is installed and my phone turned on straight into download mode
5) phone pops up in Odin3 and just click Start, flashed to stock JH6
I am 80% sure I wasn't holding the power button while holding the Vol keys. If that doesn't work above ^^^ hold all 3 buttons and it should go into download mode.
so.. I fubard framework.apk trying to get teh circle battery mod on my phone (it just hung forever and *poof* black screen o' nothing after I pulled the battery)
So.. I'm following the directions but windows keeps finding the phone as some type of crazy serial device and is asking for drivers ... so I'm fux0red methinks.
Any help is appreciated - but I think I did a real number on this thing.
Ok... these are the steps I've done.
Shutdown the device.
Pulled battery, Sim, SD Card.
Popped the battery back in.... didn't power it up.
Turned on Odin3
Popped the USB cable into the phone while holding both volume buttons.
I get the lil triangle.
... then I get a windows message stating "SERIAL GADGET" and the XP wizard comes up looking for drivers. It doesnt find anything of course.
So.. I rinse and repeat and it can't find the device.
So what am I missing o wise XDA folks?
avgjoegeek said:
Ok... these are the steps I've done.
Shutdown the device.
Pulled battery, Sim, SD Card.
Popped the battery back in.... didn't power it up.
Turned on Odin3
Popped the USB cable into the phone while holding both volume buttons.
I get the lil triangle.
... then I get a windows message stating "SERIAL GADGET" and the XP wizard comes up looking for drivers. It doesnt find anything of course.
So.. I rinse and repeat and it can't find the device.
So what am I missing o wise XDA folks?
Click to expand...
Click to collapse
Have you searched for the drivers and installed them on your xp machine?
I'm still a noob so I'm not sure of it will help.
Please though, once you get it sorted please post your solution here for the benefit of those whip comer after you.
Good luck!
Sent from my SAMSUNG-SGH-I897 using XDA App
http://forum.xda-developers.com/showthread.php?t=788093
Get the right drivers if you havent already and find the USB port that works. Post 8 above is very good. On my netbook, only one of the three usb ports works for the captivate, i've marked it since with a happy face.
Ok.. at home now on my Win7 machine - all is good in Odin restore land...
Except - I flash using the Odin 1 Click and still boot to a black screen.
I think because I had the Voodoo lagfix on it - it won't format correctly and load the rest of the ROM onto the SDCard

[Q] Odd Download mode problem

So, to start off, the issue at hand is not download mode, I can get into that quite easily. It's that neither one click odin or regular odin won't recognize it. I've gone back to stock so many times without issue, but this particular time I tried, it froze on sbl.bin. My screen turned a greenish black, and stayed on that for about 10 minutes before I decided it was frozen and I did a battery pull. Tried it again and the exact same thing happened. Now, windows says "One of the usb devices attached to this computer has malfunctioned, and windows does not recognize it"
I was going from icezar's Darky's 5.5 to stock when this happened. I've gone from the first i9000 2.2.1 stock rom back to stock 2.1 with no problems before. Any ideas? I've also reinstalled drivers, and I still get that error. also, my power button doesn't do squat when it's completely powered off. Only the volume up+down button combo can bring the download screen up, other than that, no go.
Ouch - You've reinstalled the drivers.
Odin doesn't see it when you have download mode and the USB plugged in.
Can you get ADB to see the device while in download mode?
You had USB Debugging turned on before things went south?
Hmm.. you could try:
Turn on ODIN
Remove the SIM, external SDCard, and battery.
Hold down both volume buttons - plug in the USB cable then jam in the battery and see if ODIN will recognize it then.
But.. if you can't get the computer to recognize your device even after re-installing the USB Drivers?
eh you might wait for a few more posts - but I think you might be fubard.
so you went into download mode, clicked start in ODIN 1 click and got hung up? nothing else happened during the process? Was the cable plugged all the way in?
Not sure how ADB would work if windows isn't recognizing it.. Do you have another PC you can connect to?
Sounds like it pooched while he was trying to Odin 1 Click back to stock and now its probably fubard as his computer won't recognize the device.
Good call on trying a different computer.
Btw - where are you downloading the USB drivers from? There are multiple sources out there and some seem to work better than others.
Thanks for the replies guys
I got them from the wiki page way back when around it was first put up... but I haven't really changed them since they were the only ones that I found worked at the time and pretty well actually, they've recognized my captivate perfectly all the time! Well, until recently. I also have kies mini installed if that means anything. I am gonna try a friend's computer and see what happens. *crosses fingers*
alex4lex said:
Thanks for the replies guys
I got them from the wiki page way back when around it was first put up... but I haven't really changed them since they were the only ones that I found worked at the time and pretty well actually, they've recognized my captivate perfectly all the time! Well, until recently. I also have kies mini installed if that means anything. I am gonna try a friend's computer and see what happens. *crosses fingers*
Click to expand...
Click to collapse
if you haven't already, try the files attached to the Odin 1 click thread (on any pc you can get your hands on )
not sure what options you have until you can get a pc to recognize the device
Yup.. the good news if you can get into Download mode on your phone - its def not bricked.
I use the Odin 1-Click USB drivers posted there and have had no issues on either my work rig Windows XP 32 bit or Windows 7 64-bit.
Epic success! Phone is back to 2.1 stock! Thanks for all the help joegeek and fisherman

I know,Another Bricked Phone...sigh

I had loaded the ginger clone rom and all was well. I then however wanted to swap kernels so i loaded up seitrons cwm 1.5.6 and proceeded to flash through cwm. this has now become the worst day of my life. the phone will not boot past the galaxy s screen. i cannot not get into recovery and both computers now say usb device not recognized when in download trying to flash odin. i am worried that something is corrupted on my phone because not matter how many times i uninstall and reinstall the drivers no luck. i think it is officially bricked and im sol. maybe some great minds can figure it out here.
It's not bricked - issue is trying to get your computer to recognize your phone when in download mode so you can flash it back.
What OS are you running? Also - where did you download the drivers from? Some seem to work better than others.
If you can get to the galaxy screen you might still be able to to get into recovery. pull out the battery and use the 3 button combo. Hold down both volume button then power and let go of the power button after it turns on. then just reinstall the rom
I'm willing to bet you can also get into Download Mode either with button combos, or a JIG. Once in Download, you can use Odin to restore to JF6, and have a working phone to flash around with again.
i can get into download mode no problem. and i think it is quite possible drivers are corrupted on the phone itself. my wifes phone works on the same exact setup. no usb device not recognized error. i have tried the drivers from here and samsung directly with no luck. 3 button combo does not work. sim out sim in battery out and in. but like i said it will just not register with the comp and hers will. so im going to att and seeing about replacing it. but i will see how that goes. ive done this lots of times with no issues ever.
download works
3 button combo does not so no recovery
usb device not recognized error
thanks for the help and keep it coming i will try everything if i haven't already.
Try current usb port
Sent from my SCH-I897 using XDA App
Think I'm in worse shape. Tried flashing just the kernel to get BLN working again (last ROM I put on somehow loaded a non-compatible kernel). Now the phone boots the white ATT screen and just sits there. Can't get it into D/L mode with 3-button and doesn't respond to computer I have been using to flash ROMs for a couple weeks now...
Am I hosed? ANY help would be greatly appreciated...
You could try to use a JIG to force your phone into Download Mode
Okay...well, got into D/L mode finally. Used Odin to get it back to factory. Used the One Click rooter again, except now it boots to recovery 3e, which doesn't let my power button work as the okay button Pulling the battery to reset it, but it will no longer go into D/L mode to use Odin again. It keeps booting to the recovery Utils, which I cant get out of...*sigh*
Thoughts?
at least your able to do something i still cannot get my phone into recovery or to be recognized by the computer. it is not the drivers so i have no idea. i can only think that something got funked up with the kernel flash.
if you are getting into 3e recovery then you are most certainly NOT using the JF6 one click stock
3e recovery comes on JI6 which is the FroYo leak....completely different builds and roms
have you tried a different usb cable? I was having this problem, and the stock samsung cable was B.O. and wasnt working... i tried my blackberry one and all was good
magnumrt562 said:
have you tried a different usb cable? I was having this problem, and the stock samsung cable was B.O. and wasnt working... i tried my blackberry one and all was good
Click to expand...
Click to collapse
i actually tried this yes. i had a blackberry cable from the storm (shivers) that was laying around. tried that but no luck with that or my wifes cable as well. but a good tip for others nonetheless
Pirateghost said:
if you are getting into 3e recovery then you are most certainly NOT using the JF6 one click stock
3e recovery comes on JI6 which is the FroYo leak....completely different builds and roms
Click to expand...
Click to collapse
I just want to quote this to stress the importance.
Thank you, didn't realize that (still sorta new to this)...
I downloaded a zip (I thought from here somewhere) that extracted into the 4 files. Anyone got a link to the JH6 set of files?
I also downloaded DG's "One Click Odin", but it doesn't seem to really do anything when I run it unless I manually load all the files. Also, I don't see a "Master Clean" like the post refer too
are you sure you downloaded the right odin? in the one click version, theres no option to load files at all. only a "start" and "master clear"
make sure the odin one click is open before you connect your phone.
http://forum.xda-developers.com/showthread.php?t=731989
You guys rock! I don't know how, cause I could have sworn I D/L'd it from that link before and I got the generic Odin, but it looks like I have the right one now! Thank you for your patience with us noobs as we start getting into this new world!
glad you got yours working. i have officially given up and receiving a new one on tuesday. i tried everything but somehow someway the phone is not recognized in download mode. oh well have to mess the with new one then lol
zippox180 said:
glad you got yours working. i have officially given up and receiving a new one on tuesday. i tried everything but somehow someway the phone is not recognized in download mode. oh well have to mess the with new one then lol
Click to expand...
Click to collapse
I was having the same problem. Have you tried powering off, start odin, hold both the volume up/down, then plug in the usb to your phone?

do i need to send my SGS off to samsung???

hi
i have purchased an orange branded sgs from the forums i go on. all ok, unlocked it easily enough and i wanted to update the firmware. i did look at the firmware name etc on the handset but it didn't match any online from stock firmwares.
i downloaded odin 1.3, usb drivers and I9000 xxxxjpo firmware as seemed to be right with 512 and 803 bin.
i flashed the phone following the instructions and all went fine but when it rebooted it went into recovery mode. i then rebooted the phone and it went to the s symbol and black screen with the vibrations every so often.
i used the download batch tool which worked fine as the 3 button trick didn't work but my laptop no longer picks the phone up when i plug the usb in.
i have uninstalled all the stuff like adb and kies and usb drivers and re-installed it all but still no device showing. under device manager it shows an unknown device but won't accept any drivers.
the phone charges via usb and will boot to the black screen but thats it.
is there anything else i can try? i'm not good at soldering if i definately need the jig thing.
or do i call samsung and say a crashed laptop caused my phone to break during update?
Can you access download mode at all?
To do that you hold menu and volume down and power up. Download mode will show a picture of an android with a shovel or something similar.
i can if my pc would recognise my phone as i can use the batch file mode which worked. at the moment, no.
3 button never worked. must be a dodgy samsung handset.
Don't freak out.
I had a colleague of mine in the same situation, simply use the JIG cable to force the phone in download and repartition with Odin and a stock rom:
http://forum.xda-developers.com/showthread.php?t=819551
HTH.

[Q] Simply put, i'm SOL.

SOLVED: when having trouble with your computer not making a good connection to the phone, try your USB HUB on the mother board. it totally fixed my problem!
So here it is. I received a cappy from a buddy at work.
Basically, she is running cognition (FROYO BASED) rom, not sure of the kernal, and Cwm.
i can get the phone to reboot into RED CWM recovery, and even into DOWNload mode.
The phone was shut off during a factory reset. the battery died.
(IDK the girl was a dumbass and did it from settings on the phone not in CWM )
The phone will boot, ONLY after a factory reset from CWM but the setup google accs f/c's and the only thing i can get it to do is volume up/down pull the notification bar down and power off recovey dl mode...ect ect.
Task manager say's there are no APPS installed on the phone running? yet when i go LVL 2 RAM clear, the phone says 13 apps closed..
I think the Stock APK's have been deleted, since i cannot get into menu at all.
Since she factory reset the phone, and wiped the SD CARD, ALL CWM recoveries she created are GONE.
I have Cleared the cache, and wiped dalvik code, fixed permissions.....
I'm very familiar with the VIBRANTS, not the cappy's so this is a challenge to me.
my Vibrant has connected with all the usb drivers from samsung, but the cappy cannot. I've even downloaded the drivers for just the CAPPY, uninstalled all others, and Still not recognized, yet my vibrant does?
i've installed i think every driver on here for captivates, kies downloads, even went to the samsung website and Downloaded from there.
STILL NOT CONNECTING.
Even DL'd the AIO cappy toolbox (very nice to have for my VIBRANT)
Still no avail.
THE PHONE CANNOT MOUNT THE EX SD CARD. So that idea's out.
all my drivers are correct for the 32 bit vista OS. even tried on my GF's 64 Windows 7.
Still no avail.
I've installed the drivers with the phone in DOWNLOAD mode even, still not connecting.
Rebooted the computer after removing and also reinstalling drivers.
Changed between 3 diff cords, all work for my VIBRANT,
still no avail.
Any idea's would be greatly appreciated.
Thanks.
PelvicThunder said:
So here it is. I received a cappy from a buddy at work.
Basically, she is running cognition rom, not sure of the kernal, and Cwm.
i can get the phone to reboot into RED CWM recovery, and even into DOWNload mode.
The phone was shut off during a factory reset. the battery died.
(IDK the girl was a dumbass and did it from settings on the phone not in CWM )
The phone will boot, ONLY after a factory reset from CWM but the setup google accs f/c's and the only thing i can get it to do is volume up/down pull the notification bar down and power off recovey dl mode...ect ect.
Task manager say's there are no APPS installed on the phone running? yet when i go LVL 2 RAM clear, the phone says 13 apps closed..
I think the Stock APK's have been deleted, since i cannot get into menu at all.
Since she factory reset the phone, and wiped the SD CARD, ALL CWM recoveries she created are GONE.
I have Cleared the cache, and wiped dalvik code, fixed permissions.....
I'm very familiar with the VIBRANTS, not the cappy's so this is a challenge to me.
my Vibrant has connected with all the usb drivers from samsung, but the cappy cannot. I've even downloaded the drivers for just the CAPPY, uninstalled all others, and Still not recognized, yet my vibrant does?
i've installed i think every driver on here for captivates, kies downloads, even went to the samsung website and Downloaded from there.
STILL NOT CONNECTING.
Even DL'd the AIO cappy toolbox (very nice to have for my VIBRANT)
Still no avail.
all my drivers are correct for the 32 bit vista OS. even tried on my GF's 64 Windows 7.
Still no avail.
I've installed the drivers with the phone in DOWNLOAD mode even, still not connecting.
Rebooted the computer after removing and also reinstalling drivers.
Changed between 3 diff cords, all work for my VIBRANT,
still no avail.
Any idea's would be greatly appreciated.
Thanks.
Click to expand...
Click to collapse
First, see if you can find out which version of Cognition she was running (Gingerbread- or Froyo-based).
Once you have that information, I believe you should be able to download the appropriate ROM on you computer and copy it to the microSD card (adapter or whatever method you need to do to get it there). Since you can get into CWM recovery, you could try flashing the ROM from there. Assuming it's a full wipe rom (and you're not concerned about keeping apps installed on the phone), it should reset things to a more workable state. (If you are worried about apps remaining... I don't know what to say at this point, since you can't get to Tibu.)
If that doesn't work, you could try the one-click back to stock (realizing that you're having connectivity issues, I'll get to that in a second).
When you connect the phone in download mode to ODIN, does the yellow COM:# show up?
If you have tried ODIN on your Vista computer, try running ODIN as Administrator.
I've had some luck in the past getting the phone to be recognized (assuming Froyo) by doing this:
1. With nothing connected to computer, start ODIN (one-click to stock would be good).
2. Pull battery on phone.
3. Reinsert battery, but do not power on.
4. Hold Vol+/Vol-/, and insert USB cable.
5. Wait for it to kick into download mode, release buttons, and wait again.
6. See if ODIN recognizes it.
jmtheiss said:
First, see if you can find out which version of Cognition she was running (Gingerbread- or Froyo-based).
Once you have that information, I believe you should be able to download the appropriate ROM on you computer and copy it to the microSD card (adapter or whatever method you need to do to get it there). Since you can get into CWM recovery, you could try flashing the ROM from there. Assuming it's a full wipe rom (and you're not concerned about keeping apps installed on the phone), it should reset things to a more workable state. (If you are worried about apps remaining... I don't know what to say at this point, since you can't get to Tibu.)
If that doesn't work, you could try the one-click back to stock (realizing that you're having connectivity issues, I'll get to that in a second).
When you connect the phone in download mode to ODIN, does the yellow COM:# show up?
If you have tried ODIN on your Vista computer, try running ODIN as Administrator.
I've had some luck in the past getting the phone to be recognized (assuming Froyo) by doing this:
1. With nothing connected to computer, start ODIN (one-click to stock would be good).
2. Pull battery on phone.
3. Reinsert battery, but do not power on.
4. Hold Vol+/Vol-/, and insert USB cable.
5. Wait for it to kick into download mode, release buttons, and wait again.
6. See if ODIN recognizes it.
Click to expand...
Click to collapse
Thats my problem, the cappy does not see that there's an EX SD card there at all? says no files, but i've tried to push a cognition rom to the EX SD and use CWM to flash it to get it to boot, but the phone cannot see that there's an EX SD, but the SD card is fine, even my vibrant used it..
ODIN as ADMIN? tried that and nothing, still no yellow com port,
i know how to use odin, as my VIBE has been "Bricked" a few times lol
the vol up/down button combo does nothing, just shows up as a charging screen, the only way i can get the phone to download mode is through CWM.
the phone is running a FROYO based cognition ROM. or that's what her bf put on there.
This may sound stupid and simple but is the device set on mass storage from the settings menu? If you know.
Also have you tried mounting your sd cards in CWM?
Rhiannon224 said:
This may sound stupid and simple but is the device set on mass storage from the settings menu? If you know.
Also have you tried mounting your sd cards in CWM?
Click to expand...
Click to collapse
lol THATS MY PROBLEM> the phone thinks it boots normally, but i cannot get the settings menu. like the "SETTINGS APK" file was deleted when she formatted the SD!
but i was just playing around and i got google voice search to pop up!
then from there i used my WIFI and setup the google settings, then i went to the market grabbed CWM and used the cognition rom i've already downloaded, and used it!
then the GREEN CWM booted, and it still cannot MOUNT EX SD card. so the flash failed.. HMMMMMM
As of now i am gonna go into the rom i DLed (cognition) and try to DL Root explorer and hard push the Settings.apk file to the system. HOPEFULLY from there i can get my settings back to restore the phone.
Realizing that it's a long shot at best due to connectivity issues, have you tried using ADB?
If so, you could push the ROM you need to the internal SD.
so, used root explorer to move the NEW cognition froyo rom from the EXternal SD to the INTERNAL SD. from there i used CWM recovery to flash the rom, the rom flash was successful, but now the phone is stuck in bootloop on the AT&T world phone screen.
and CWM will not LOAD. FML
Looks like i'm gonna have to take this apart and get to the internal SD card. =/
Can you get to CWM with the Vol+/Vol-/Power combo - hold those past one AT&T screen and when you see the second one, let go?
Adb was not an option at that point, the phone couldn't recognize it even had a phone attached to it.
but now that i'm stuck in bootloop and with no CWM recovery OR DL MODE, yeah the jig isnt' workin... HAHA
i guess its just a paperweight now.. Owell, i tried.
i held it for about 3 mins... lol and the jig i got for my VIBRANT isn't workin either. I didnt know these phone's can lose the 3 button combo reset? i often flash I9000 roms to my vibe, thats why i have a jig, but i didnt think cappy's would do that unless i flashed an i9000 rom to it? lol
Just because I'm not sure if you tried it - have you tried plugging the cable into a different port on your computer? If it's not one directly connected to the motherboard, that can sometimes cause problems getting the phone to be recognized.
Also - does the phone show any signs of recognizing there is a cable inserted (like charging)?
tried every port. No the phone only acts as if it wants to display the batt charging symbol, but does not show, I cant believe it, i actually think i bricked a galaxy s.. haha
Another long shot, but you could try the One-click unbrick. Since it's Heimdall-based, there's always a chance.
Wow, didnt know that even existed. Definately gonna be useful for my Vibrant, haha i'll give it a shot.. THANKS, i'll report back after i try it.
I hope it does something. With the connectivity issues you're seeing it's starting to sound a little like hardware issues.
I'm going to throw out a checklist of stuff, knowing that you are already experienced with ODIN and ROM flashing, simply because I know I usually can use some sort of checklist to make sure I've caught everything.
- Redownloading/reinstalling drivers, rebooting before connecting phone
- Redownloading/reinstalling ODIN package
- Redownloading ROM to flash
- Hold V+/V-, inserting USB cable
- Remove battery, hold V+/V-, insert USB, insert battery
- Hold V+/V-/HOME softkey
- Hold V+/V-/HOME/Power
- If download mode reached, allowing phone to sit connected for long time
- If download mode reached, connecting phone after opening ODIN
- If download mode reached, connecting phone before opening ODIN
- If download mode reached, connecting phone after ODIN, disconnecting, reconnecting phone
That's all I can think of for a checklist of stuff to try/retry.
I appreciate the help but i've tried all of those options several times, The jig did work to get it into DL mode, but from there i'm still in the same **** position, my computer will not recognize that the phone is connected.
Is it possible that the phone somehow lost its drivers? what i mean by that is, the phone acts different with different USB ports, completely.
On one port it says unknown device, another USB android composite device.
Its as if the phone's changing as i change ports. Very FRUSTRATING!
i think it could be a hardware issue myself, but how could a corrupt drive work so well? To the T every time i've used the jig DL mode fired up, but my computer still cannot find the drivers to run it. Hell i've even tried using winusb drivers package to force install the phone, still no avail.
Like i said, I really appreciate the input, I figured if i couldnt figure it out, someone on here had some EXP in doing this lol i've just never had a driver problem give me so much trouble. IDK, bout ready to turn this paper weight into a pile of ash.
If you can get into cwm, have you tried doing another hard reset/factory wipe?
Thats the problem, earlier i COULD get into CWM, and hell i flashed the new rom perfectly!
now it is stuck bootlooping, therefore i just used the Jig, and first few times it didnt work, now its stuck bootlooping, download mode is attainable, and still NOT connecting to my pc via usb.
mrhaley30705 said:
If you can get into cwm, have you tried doing another hard reset/factory wipe?
Click to expand...
Click to collapse
Nvm, reread your post. Have you tried flashing a different rom?
PelvicThunder said:
Thats the problem, earlier i COULD get into CWM, and hell i flashed the new rom perfectly!
now it is stuck bootlooping, therefore i just used the Jig, and first few times it didnt work, now its stuck bootlooping, download mode is attainable, and still NOT connecting to my pc via usb.
Click to expand...
Click to collapse
Try a different computer? also, which version o of odin are you using? I've found 1.3 & 1.82 to work best.

Categories

Resources