Following the guide atnookcolormods and when I try:
Code:
adb shell mount -o remount,rw /dev/block/mmcblk1p2 /system
I get: error: protocol fault (no status)
My NC is attached as confirmed by adb devices, which shows my serial number.
Any ideas? Obviously new to all this...
Windows 7
Thinking Linux would be better for this... But my linux box is not here right now.
EDIT:
Figured it out. It said nothing about pressing the SuperUser icon..
SuperUser icon
What exactly does your comment mean because I am having this problem and I'm not sure what to do about it.
means that you have to open SuperUser in your nook in order to push files via ADB from your computer
error: protocol fault (no status)
and how am I to do that? What setting do I add/change in SuperUser?
I was getting the same error while my nook was asleep. I woke it up and it worked fine. Common sense I guess, but took me a minute.
Related
While using cyanogen's rom, Droid wall gives an error when you apply the settings. Here's what i did to get it to work the first time(only):
Connect phone via usb
Open command-prompt
Type adb devices - you should see your phone's serial number
Type adb remount - should say remount succeeded
Type adb shell
Type chmod 755 /system/bin/iptables
Type exit
Type adb rebootAfter the reboot you can install Droid Wall and apply the settings successfully.
still figuring out.....
rodrigo.zr said:
What ROM are you using? It is possible that the iptables bundled with your ROM does not support the "owner" module which Droid Wall makes use.
You can try a few things:
Restart your phone and click on "Show rules" again to see if anything has changed.
If that doesn't work:
Start an "adb shell".
type:
iptables -A OUTPUT -o rmnet+ -m owner --uid-owner XXXXX -j ACCEPT
(replace XXXXX by the number displayed by Droid Wall right before the the browser - 10028 on mine)
Check the iptable output for any errors.
If your iptables don't support this module you can probably update it and check if that works.
Cheers!
Click to expand...
Click to collapse
Droid Wall author discussion here
Pending issue
Cyanogen's google code website has a listed issue regarding this for the N1. But it's been marked closed.
I have a v6 stock phone, no root, no cwm. Thought I would run through the ADB manual method of root to see what happens. I get to this point...
Code:
>adb devices (verifies you are connected)
>adb push rageagainstthecage-arm5.bin /data/local/temp/rage
(if the above command fails due to read-only, type 'adb usb' then 'adb root' to validate root status, then 'adb devices' again to verify connection)
>adb push su /data/local/temp/su
>adb shell chmod 777 /data/local/temp/rage
>adb shell ./data/local/temp/rage
When I try to do the SU because I get the $ I get Permissions denied.
I know that this method does not work but I wanted to see where it fails. It appears that they may have fixed the glitch that allowed the rage exploit to work.
I also tried cubes other way and it failed as well.
Code:
Open ADB shell
Your command prompt should be "$"
Run
kill `busybox pidof adbd`
Re-run ADB shell, your command prompt should change to "#"
Just thought I would toss this out there in case someone wanted to know...
Thanks for the heads up on this good info to know when I get my rev on Saturday
Sent from my SHIFTAO5P using XDA Premium App
Haxcid said:
I have a v6 stock phone, no root, no cwm. Thought I would run through the ADB manual method of root to see what happens. I get to this point...
Just thought I would toss this out there in case someone wanted to know...
Click to expand...
Click to collapse
Mm, I went through that last night, then downgraded to the V4 software as shown by the other post - still, none of it worked for me.
Pull your SDcard out when trying to root after the downgrade. Or format the SD card. It should work then.
Hi
I'm a new owner to a Galaxy tab 8.9 and trying to make it able to mount NFS exports.
So I've rooted the device, installed SuperUser and terminal emulator. Then I downloaded the kernel source tree from Samsung, I compiled the NFS module on my desktop computer moved it to /system/lib/modules on the tab. But it doesn't work, when I do 'insmod nfs.ko' it gives back 'insmod: init_module nfs.ko failed (No such file or directory)'
Is it possible at all to add modules to the standard kernel that comes with the device?
Is my device completely rooted because when I try 'adb root' I get 'adbd cannot run as root in production builds'
me too...
I just encountered the exact same problem on my LG Revolution, except I'm trying to load nfsd.ko for server support.
I know I built it correctly because I've already succeeded in getting tun.ko working properly...
Code:
root # /system/bin/insmod /system/lib/modules/nfsd.ko
insmod: init_module '/system/lib/modules/nfsd.ko' failed (No such file or directory)
root # ls /system/lib/modules
... nfsd.ko
Very odd...
When you do the insmod are you actually in the /system/lib/modules directory? If not, you have to use the full path to the module.
The message with "adb root" is normal even on a rooted device. If you can do "adb shell" followed by "su" you should be ok.
edit...
Now that I think of it...that message usually means the module file was found but a dependency wasn't.
gtj0 said:
Now that I think of it...that message usually means the module file was found but a dependency wasn't.
Click to expand...
Click to collapse
Yep that was my problem. My nfsd.ko needed dependencies that didn't exist...
To the OP: try to insmod the nfs.ko module again and then look at the output of dmesg. You should see messages complaining about the dependencies required by the nfs module.
Then you ought to be able to either remove the requirement for them from your module (my nfsd.ko wanted posix_acl support so I just got rid of that option and rebuilt the module) or if it's something you need/want you might be able to add support for whatever it is as another module...
Good luck and I hope I didn't intrude upon your thread too much
Thanks, I had indeed a dependency problem. Now I managed to load nfs.ko and sunrpc.ko and lockd.ko that were needed because of dependency.
Although I'm still having problems at mounting an nfs export. Previously, before kernel module problem was solved, I got the error message 'No such device' when I tried to mount, now I get 'Invalid argument' instead.
I've tried commands like
busybox mount -t nfs 192.168.1.100:/mnt/raid/media /sdcard/nfs
and
busybox mount -o nolock,ro,hard,intr,vers=3 -t nfs 192.168.1.100:/mnt/raid/media /sdcard/nfs
Any thoughts?
NFS Share - Invalid Argument
Marlin79 said:
........... now I get 'Invalid argument' instead.
I've tried commands like
busybox mount -t nfs 192.168.1.100:/mnt/raid/media /sdcard/nfs
and
busybox mount -o nolock,ro,hard,intr,vers=3 -t nfs 192.168.1.100:/mnt/raid/media /sdcard/nfs
Any thoughts?
Click to expand...
Click to collapse
Seems like an Old thread, and I would assume you've gotten this fixed already, but in case it ISN'T fixed...
>Double check your NFS config (/etc/exports file) and confirm that you are sharing:
* /exports/mnt/raid/media *
If you specified something else in your /etc/exports file, check to make sure your Hard drive (I assume /mnt/raid/media) is soft-linked to the share name you wanted to give it, or that at least the subfolders/files you want shared are softlinked to the /exports/share directory.
**e.g.**
# ln -s /exports/media/ /mnt/raid/media
-OR-
# ln -s /exports/media/shared_media_1.mp4 /mnt/raid/media/actual_file.mp4
I wanted to enable SCP and SSH using DropBear II ... for some reason DropBear Server II doesn't install scp & ssh binaries, you can get them from github and symlink it into system. Here's what I did...
DropBear archive (1M): https://www.dropbox.com/s/h2guipuvdltiden/dropbearii.zip
Feel free to mirror that if you want.
These directions allow you to ssh into the system as root, be very careful. I recommend not leaving the service running if you are not using it.
I take no responsibility if you brick your unit while mucking around as root.
Back Up
Download dropbearii.zip and unzip on your local file system.
From your local filesystem install the APK and push scp & ssh to tmp.
Code:
adb install DropBearServer2.1.apk
adb push scp /data/local/tmp/scp
adb push ssh /data/local/tmp/ssh
From the OUYA GUI install the DropBearServerII service... Select Make -> Software -> DropBearServer II -> Install
Shell into your OUYA and make /system writable.
Code:
adb shell
su
mount -o rw,remount -t ext4 /dev/block/platform/sdhci-tegra.3/by-name/APP
Move scp & ssh into DropBear II directory
Code:
mv /data/local/tmp/scp /data/data/me.shkschneider.dropbearserver2/app_data/
mv /data/local/tmp/ssh /data/data/me.shkschneider.dropbearserver2/app_data/
Change the permissions
Code:
chmod 6555 /data/data/me.shkschneider.dropbearserver2/app_data/scp
chmod 6555 /data/data/me.shkschneider.dropbearserver2/app_data/ssh
Create the symlinks
Code:
cd /system/bin/
ln -s /data/data/me.shkschneider.dropbearserver2/app_data/scp ./scp
ln -s /data/data/me.shkschneider.dropbearserver2/app_data/ssh ./ssh
Change /system back to read-only (optional) and exit.
Code:
mount -o ro,remount -t ext4 /dev/block/platform/sdhci-tegra.3/by-name/APP
exit
exit
Reboot the OUYA (optional)
Code:
adb reboot
Notes/testing
Windows users can use Putty to ssh & scp get them here.
To ssh into the system:
Code:
ssh [email protected]_ADDRESS
To scp a file to the sdcard:
Code:
scp ./some_file [email protected]_ADDRESS:/sdcard/
To get to settings push the U circle button one time.
If you turn on "Start on boot" in the settings menu and reboot, the service will be turned off. Though it will be left on in the standard standby mode.
I recommend using pubkey rather than password. Basically generate a public key and push it into /sdcard/ then install it from the DropBear II app.
Unix Hosts can do:
Code:
ssh-keygen -t rsa
Windows using PuttySSH follow these directions, I haven't tested them though.
If you don't want to be bothered with pubkey, please change the default password it is set to 42.
If you already know about pubkey, you can cat them into: /data/data/me.shkschneider.dropbearserver2/app_data/authorized_keys
Unchecking "Allow Password" doesn't work properly.
Why would I want to do this? I didn't really like the Wireless ADB disappearing after the OTA upgrade, this may be less annoying if the next OTA doesn't nuke it.
I'm getting an error that busybox is not installed when trying to start the service. Is there anything special you had to do with busybox to get this to run? I installed it via the apk.
Edit: Nevermind. I didn't realize the busybox apk was an installer and I didn't find the icon when I looked. Just checked again and found the busybox installer icon and did a smart install. Dropbear ssh is running now.
I ran it manually with
Code:
dropbear -E -s -P /data/dropbear/dropbear.pid -r /data/dropbear/dropbear_rsa_host_key -d /data/dropbear/dropbear_dss_host_key
and it looks ok when idling but when connection it gives me
Aiee, segfault! You should probably report this as a bug to the developer
Click to expand...
Click to collapse
This could be CM10.1 environment issues (libc). The built-in SSHd doesn't work properly as well. Some binaries give strange errors when executed with SSHd (like sqlite3).
I can't install the DropBearServer II from the Make option, comes up with "operation failed". Tried to make the system rw to see if that might have been the problem but still no luck. Anyone else had that problem?
andlid said:
I can't install the DropBearServer II from the Make option, comes up with "operation failed". Tried to make the system rw to see if that might have been the problem but still no luck. Anyone else had that problem?
Click to expand...
Click to collapse
I installed it via adb.
For others I was able to install using IncognitoMan's -=StockPlus=- ROM -- http://forum.xda-developers.com/showthread.php?t=2347214
You may need busybox installed, I'm not 100% sure, I haven't tried without busybox.
SSH command line on android
The link is broken
Could someone please reupload this? would be awesome
Thank you so much
BIade said:
Could someone please reupload this? would be awesome
Thank you so much
Click to expand...
Click to collapse
bump - upload again please
You can also get static binaries from dropbear or ssh server apks in playstore by simply unpacking the apk.
I have tried:
##2846579## which does nothing
Removed the line of code in /system/etc/init that says:
rm /dev/log/main
I have usb debugging enabled, I have tried resetting ADB in devices, and I have the following error still that states
"Unable to open log device '/dev/log/main'": No such file or directory"
I would appreciate ANY help to get this resolved...