Does anyone have the PIT file for use with the factory VZW Firmware. I found a copy of the original firmware to load with Heimdall and can get it to basically bring up a Samsung logo and I can get to download mode only.
I have tried 512 and 513 both give the same results. I can see the device when I do an ADB devices poll and I can reboot the phone into recovery and download but recovery hangs at the samsung logo as well.
Not a full blown brick since I can talk with it and work with it, I just need the correct files to reload.
Thanks in advance!!!
Anybody?
Are there any other possibilities as to what could be the root cause if its not the partition table? suggestions for ways to test?
Major Update!!!
Used Odin 1.7 to repartition with the P1 Pit, then switched to Heimdall to load a Verizon backup posted on another forum.
After about 5 mins in heimdall load the phone rebooted and now gives me access to the recovery mode but even after a wipe and reset the phone seems to bootloop at the verizon logo.
Definitely now know that for future Verizon is running the P1 Pit or at least close to it. 512, 513, and 803 would only freeze at samsung.
Edit.
I also now have regained access to the ADB shell, before I had adb and could see the devices but Shell came back with a "cannot locate in /system/bin/su"
Anybody have any suggestions on getting passed the revolving the Verizon bootup? just loops and vibrates.
Have you made any progress on ur tab? I am in the same exact situation, everytime i flash with heimdall 1.1.0 or 1.1.1 and the verizon stock rom found in the forums, my tab gets the phone and computer yellow triangle warning, the only way i can get it out is by using odin 1.70 and either the p1_add_hdden or the 909 pit to get it back to the verizon logo but with the vibrations and looping. If anyone has a known good pit file please please post it or direct me on how to extract one from my brothers tab.
Unfortunately my nandroid backup fails the md5 when i try using odin and im missing using it sooooo much :-(. thank you in advance for any help and i just have to say i try not to post as much as possible and do all the research i can but i am hitting a wall here and ive tried for days now
I am also in the same boat. I need a working PIT file
This is what you'll have to do
1. Turn off your device
2. Hold up volume button + power button
3. As soon as you see the Samsung logo, release the power button
4. With the up and down volumne button move up and down on the menu and select wipe data/factory reset option
5. Then press home
6. Finally, wait until it finish and select the reboot system now option and then press home
1. Make sure you have the drivers installed. If not search and download the Heimdall application and extract contents to a directory and look for the drivers directory. Then select Samsung USD composite device and then Install the driver.
2. You'll need to search for the correct stock file for youtr tab, then load it using the Heimdall program, follwing this instructions:
- The zImage goes in both the Kernel AND Recovery slot.
- The system.rfs goes in Factoryfs
- The Param.lfs goes in Param.lfs
- And the cache goes in the cache slot.
3. Finally hit Start
4. When it finish, you got to follow my post above
Bump for this thread. I need to restore my tab and need a working pit file. Anyone figure this out?
I'm in the same boat, got my tab jtagged and now need working Verizon .pit file to repartition. Has anybody got one yet?
Me too, somebody help me to find .PIT for verizon galaxy tab 7
BUMP... dl mode works heimdall flashes correctly but even after recovery mode cache and data wipe it still bootloops with the triple vibrate cant get past it... i assume it has something to do with the partitions from rfs to ext4 sooooooooo please can someone find a working cdma pit file
I'm in the same boat as you guys, really need a valid verizon pit file after a bad flash. Any help would be much appreciated!!
Try this pit file from my VZW tab.
leothreenine said:
Try this pit file from my VZW tab.
Click to expand...
Click to collapse
flashed with odin...
didn't really do anything :\
ppctester said:
flashed with odin...
didn't really do anything :\
Click to expand...
Click to collapse
If you can go to Recovery mode, try if you can successfully do a factory wipe. If you see error messages while doing factory wipe. Please include it to you post.
Please also specify what version of android you had last.
Download heimdall 1.3.1 then install. You can down pit file from it.
Sent from my SHW-M180L using XDA
here is a pit file i came across from a stock verizon firmware i aquired hope it helps..
insomniak420 said:
here is a pit file i came across from a stock verizon firmware i aquired hope it helps..
Click to expand...
Click to collapse
That worked. Thanks a million :good:
Related
I have a SGS with firmware I9000XWJG5 and Root. I tried to do a Speed fix, but afterwards it was slower so i tried to flash the phone with the I9000XWJG5 firmware again.
After the flash, the phone rebooted and i came to the recovery menu. There the phone wrote:
update media, please wait
and in the next lines:
E: Can't mount /dev/block/st110
(invalid argument)
E:copy_dbdata_media:Can't mount DBDATA:
copy default media content failed.
Now when i try do start the phone, i get a black screen after the bright S
What i have tried: Flash agein with and without re-partition and Factory Reset
Has anybody an idea what i can do?
and sorry for my bad english
bump. can anyone help with this topic..
i am having some problem..
help us guys
thanks
Fixed... use odin 512
Thread moved in Galaxy S I9000 General.
I can definately help with this one, as I worked through it last night...
I found that if you're trying to flash the JG5 rom (as mentioned in Modaco's thread) with the 513 Pit file, then you'll get the black screen of despair!! For some reason the two combination of the two don't work.
However, if you do a google search for Odin PIT 512, then download this file
You will be able to download the 512 PIT file instead. Now use this in Odin3 to flash the JG5 rom and you should have no further issues....it worked for me.
I also discovered that Samsung have just released a later firmware, so I just flashed this one on top of the JG5 one...I have a nicely running phone now.
Hope this helps...it did me!
Mike
Mine was completely knackered. Couldn't get to recovery either. Flashed Modaco's MCR R3, after the JG5 flash, using all the files in the JG5 download. Working a treat...
Cheers,
BS...
blacksoul93 said:
I have a SGS with firmware I9000XWJG5 and Root. I tried to do a Speed fix, but afterwards it was slower so i tried to flash the phone with the I9000XWJG5 firmware again.
After the flash, the phone rebooted and i came to the recovery menu. There the phone wrote:
update media, please wait
and in the next lines:
E: Can't mount /dev/block/st110
(invalid argument)
E:copy_dbdata_media:Can't mount DBDATA:
copy default media content failed.
Now when i try do start the phone, i get a black screen after the bright S
What i have tried: Flash agein with and without re-partition and Factory Reset
Has anybody an idea what i can do?
and sorry for my bad english
Click to expand...
Click to collapse
hello, i got the same problem. trying to reflash with I9000XXJPY 2.2.1 and the 512 pit, but still the same problem.
ash969 said:
hello, i got the same problem. trying to reflash with I9000XXJPY 2.2.1 and the 512 pit, but still the same problem.
Click to expand...
Click to collapse
Same here.
I tried JS3 and going back to JP6....and always the same result.
I'm obviously missing something. Maybe my 512.PIT is corrupted. I get the black screen and the same /dev/block.st110 errors in recovery.
i beleive you need to have a CSC file also for the odin flash.
i sorted mine like this:
Downloaded some JP2 odin files [used this as this was the only one on Samsung-firmwares that had all 3 PDA, Modem and CSC Files. flashed this using a .512 pit in odin. - this allowed the phone to boot normally.
connected to Kies and using reg hack [set to XEU] managed to update to JPY.
the following the Darky guide, flashed the CF Root kernel, installed the ROM Manager from the market, using the recovery mode installed the update.zip file for clockworkMod.
Formatted everything in ClockworkMod
Factory Reset in ClockworkMod
Installed Darky ROM V8.0 Wipe
thanks for your find !
Rumble6059 said:
i beleive you need to have a CSC file also for the odin flash.
i sorted mine like this:
Downloaded some JP2 odin files [used this as this was the only one on Samsung-firmwares that had all 3 PDA, Modem and CSC Files. flashed this using a .512 pit in odin. - this allowed the phone to boot normally.
connected to Kies and using reg hack [set to XEU] managed to update to JPY.
the following the Darky guide, flashed the CF Root kernel, installed the ROM Manager from the market, using the recovery mode installed the update.zip file for clockworkMod.
Formatted everything in ClockworkMod
Factory Reset in ClockworkMod
Installed Darky ROM V8.0 Wipe
Click to expand...
Click to collapse
thanks mate ! after a huge scare sorted mine with this firmware as well, this after I tried several other newer firmware packages from samfirmware and was ,slowly but surely ,starting to lose hope ...
for some reason this particular firmware JP2 seems to fix this problem
cheers and thanks again for your find !
fix for black screen after flash with no recover or download mode working.
Hey All.
So like the subject says, you flash and then your phone restarts or whatever, and then you get the normal galaxy s startup, with the sound and the visuals, but then that's it. Henceforth you are greeted with the two lights (if its a Bell Vibrant) from your options and back keys.
To fix it use the attached file. Its called ADB or something - I just know it works. It was a fix for the galaxy s phones that didnt have the recovery/download mode stock.
so here is how it goes:
1. download adb to your desktop and unpack it (if its in winrar or zip or whatever) to a file folder named adb.
2. open a command prompt.
3. type "cd" and then the address of the "adb" folder. so for example it should be in C:\Users\your user name\Desktop\adb. where "your user name" is your user name a duh.
4. plug in your galaxy s via usb.
5. type "adb reboot download" in the command prompt. copy it using your mouse as well.
6. turn on your phone.
7. press enter in the command prompt, then keep copying and pasting and pressing enter until you see the download screen on your phone. each time you press enter it says device not connected or something but just keep trying.
the article i read:
can't post it but the thread is called "How to get the 3 button recovery mode working"
Credit to Goots from samsung galaxy s forums. Go Goots!
I flashed darky's rom with the voodoo lag fix and then stupidly tried to flash over the top my recovery file. now its stuck loading. can't access recovery mode but can access download mode... any ideas?
Just posted this in another thread, with similar issues, try this, should fix it.
--------------------------------
HI,
Try the following, worked for me
1) Go into recovery mode and wipe both cache and partition data
2) go to samfirmware.com and download the original rom for your phone (the one that came with it)... since you don't say what region you're from, I'll give you an example with mine. Mine is from Bell, and factory comes with UGJH2, so i downloaded that with ODIN and the PIT FILE, make sure to extract the TAR file from inside the RAR file. Put all 3 files in the same folder
3) Enter download mode, when the phone is in that state sometimes it's hard to access download, best way is... remove the battery, put it back in, then hold VOL DN + HOME + POWER until you see a working android bot inside a triangle. When you see that, connect your phone to your PC, double click on ODIN, then load the PIT file (CHECK BOX RE-PARTITION leave the others to default) and Select PDA and find the TAR file you extracted in STEP 2... then click on START, it's gonna take a few mins, and even after it's done, it's going to reboot, and it'll stay at the "S" logo for a bit, leave it, then it'll boot.
At least we hope it will.
Keep us posted,
Thank you,
Rodi.
------------------------------------
Can't get into recovery mode only download mode?! I'm on orange uk custom galaxy S Rom 2.1 originally. shall i just follow your steps but use a stock samsung android firmware?
Thanks Alot btw!
Yeah keep going with the download mode, it's very possible that the recovery mode process is not even necessary, but since I have no way of testing, it's doesn't hurt to try.
so get the orig rom, with pit associated with its (u'll see in on sam firmware which pit you need, most likely 512 for stock out of the box).
Keep us posted
Rodi
Fixed!!! flashed the new 2.2.1 firmware as well. is flying thanks for the help
alcurtis93 said:
Fixed!!! flashed the new 2.2.1 firmware as well. is flying thanks for the help
Click to expand...
Click to collapse
i have the same problem as u ..which 2.2.1 firmware did u flash and where to download ?
Cris
Dont worry mate easier to fix than I thought. Go to samfirmwares and go to firmware section and galaxy s and its called I9000 jpu. If you need any more help dont be afraid to ask
Sent from my GT-I9000 using XDA App
Heres the link.... http://www.multiupload.com/PUSOOBQ8K5
Password is samfirmware.com
Sent from my GT-I9000 using XDA App
alcurtis93 said:
Heres the link.... http://www.multiupload.com/PUSOOBQ8K5
Password is samfirmware.com
Sent from my GT-I9000 using XDA App
Click to expand...
Click to collapse
Thanks so u much
I have a Rogers i896 build 10.10 running froyo. I just tried to restore back to stock rogers froyo JL1 using Odin 1.81 and using a 512 pit file. I entered into download mode and the odin process complete then the phone reboots.
Now it entered into android system recovery <3e> . with this menu:
Reboot system now
reinstall packages
delete all user data
delete cache data
format internal sd-card
it also says the following...
update media, please wait
E: Can't mount /dev/block/stl10
(Invalid argument)
E:copy_db_data_media:Can't mount DBDATA:
your storage not prepared yet. please use UI menu for format and reboot actions
copy default media content failed.
Click to expand...
Click to collapse
I'm a complete noob at this.. I read a lot and thought i'll give it a shot to flash a new rom.
Update. Tried to reflash, didn't work.
Tried to reflash with Stock Rogers Eclair, didn't work just went to the Recovery <2e> same error message with can't mount ....
I think this is bricked...
Any way around this?
did you just use the pit file and thats it? did you use the tar file in the pda slot as well?
Pirateghost said:
did you just use the pit file and thats it? did you use the tar file in the pda slot as well?
Click to expand...
Click to collapse
I used the stock rogers froyo tar file from this link
http://forum.xda-developers.com/showthread.php?t=905042
My phone can't even be turned off. I tried all the options in the menu and it gives me the same error message.
I think the only way to turn it off is if I remove the battery
likiud said:
My phone can't even be turned off. I tried all the options in the menu and it gives me the same error message.
I think the only way to turn it off is if I remove the battery
Click to expand...
Click to collapse
Sounds like a bad flash, can you get into download mode and try a reflash?
I just pulled out the battery to turn it off, and managed to get to download mode again. This time I tried odin 1.7. Odin says passed... but still the same error message
One thing I noticed that the re-partition check box on odin is checked when i put the pit file in there. I didn't realized it was checked so I clicked start with that on. It wasn't checked when I first opened the program. I just tried to reflash with it off, and same result
Is there no one here that can fix it?
I did some more searching around and found this post from the i9000 forums...
http://forum.xda-developers.com/showpost.php?p=8683455&postcount=7
I guess I was suppose to uncheck re-partition and the stock rogers roms does not include cache.rfs and dbdata.rfs file inside.
Anyone know if there's a way to get a ROM that includes those files in them so I can reflash it?
here i used this stock 2.1 with odin 1.7 and it worked.
http://dl.dropbox.com/u/19201431/SGH-I896_UXJI2StockRogers2.1.zip
your phone isnt bricked. bricked is a specific thing and has a special screen.
flash 2.1 when doing stock. 2.2 stock includes 3e recovery and it requires all update.zip files to be digitally signed. there is a way around it but its extra steps. instructions here
http://forum.xda-developers.com/showthread.php?t=909213
I tried to flash to stock 2.1 with odin but same thing happened.
It boots into recovery and i can't do anything... except its 2e instead of 3e that i saw before.
whats the exact filesize of the tar you used?
also if you dont re-partition, you dont need a pit file. (the p stands for partition)
The exact file size for the TAR is 238 MB (250,420,736 bytes)
I didn't know PIT is re-partition until after the fact.
Ok, I'm going to see if I can get my phone in the same condition as yours and then fix it. BRB...
Broke it and fixed it. Details in a sec.
Ok my steps to break it:
Flashed UXJL1 with Odin 1.81 using 512.pit and repartition checked.
Boot lands in recovery with can't mount error.
Steps to fix.
Used Odin 1.81 to flash the JH2 firmware from this post: http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36.
Did not check partition, did not load a pit file.
I've seen that error before but I couldn't remember how I fixed it. I think the key is simply to Odin flash 2.1 firmware using no pit and no repartition. I chose the package above because it doesn't change your boot loader and is compatible with newer phones.
flash into the AT&T 2.1 with the one click, what you probably did was Odin into the rogers 2.2 without turnning off lagfix. for some reason the rogers version doesnt actually repartition your phone.
opcow said:
Ok, I'm going to see if I can get my phone in the same condition as yours and then fix it. BRB...
Broke it and fixed it. Details in a sec.
Ok my steps to break it:
Flashed UXJL1 with Odin 1.81 using 512.pit and repartition checked.
Boot lands in recovery with can't mount error.
Steps to fix.
Used Odin 1.81 to flash the JH2 firmware from this post: http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36.
Did not check partition, did not load a pit file.
I've seen that error before but I couldn't remember how I fixed it. I think the key is simply to Odin flash 2.1 firmware using no pit and no repartition. I chose the package above because it doesn't change your boot loader and is compatible with newer phones.
Click to expand...
Click to collapse
Thank you so much! This worked! Except it now shows ATT for a brief moment but that's not a big issue. I went ahead and installed Serendipity smoothly!
opcow said:
Ok, I'm going to see if I can get my phone in the same condition as yours and then fix it. BRB...
Broke it and fixed it. Details in a sec.
Ok my steps to break it:
Flashed UXJL1 with Odin 1.81 using 512.pit and repartition checked.
Boot lands in recovery with can't mount error.
Steps to fix.
Used Odin 1.81 to flash the JH2 firmware from this post: http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36.
Did not check partition, did not load a pit file.
I've seen that error before but I couldn't remember how I fixed it. I think the key is simply to Odin flash 2.1 firmware using no pit and no repartition. I chose the package above because it doesn't change your boot loader and is compatible with newer phones.
Click to expand...
Click to collapse
there is a new fix for reference! no ATT boot logo/ fix ATT boot logo and NO dbdata error!!!
http://forum.xda-developers.com/showthread.php?t=979133
link in my sig too!
Could some one for benefit of Indian Tab Owners, write a step-by-step instructions or guide. Lot of information to digest for a new user including details of 1) rooting 2) installing recovery 3) flashing ... this information would be great useful for everyone.
My Tab details :
(Model: GT-P1000 | Code: INU | Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)
hey..even i have a galaxy tab indian version...just follow the guides that are avaliable here for rooting flashing etc...etc...and i had the same modem when i bought it but its since been upgraded to a newer version of the modem so i just updated the modem to the ...DXJM2 version..thought the asian modem would be better for me..if u want i'll post the modem.bin
Dare{D}evil said:
hey..even i have a galaxy tab indian version...just follow the guides that are avaliable here for rooting flashing etc...etc...and i had the same modem when i bought it but its since been upgraded to a newer version of the modem so i just updated the modem to the ...DXJM2 version..thought the asian modem would be better for me..if u want i'll post the modem.bin
Click to expand...
Click to collapse
Thank you for quick reply. I started compiling the files need to flashing. So far, I could do following. Please advice me whether I am on the right path or not.
1. Rooted my tab with Z4root. Now I got root permission.
2. Downloaded Odin3 v1.7.exe and s1_odin_20100803.pit for flashing
3. Downloaded Roto-JMI-Full-v2.zip and Roto-JMI-Upgrade-v2.zip
Now, using Odin PDA button, I want to flash Roto-JMI-Full-v2.zip ?
Few questions:
a) Is this correct way of flashing or I am missing something?
b) Does above flash install Recovery also ?
c) which files need for PHONE and CSC files ?
d) Which firmware best suitable for Indian Tab ?
Thank you in advance for clarifying above.
I really appreciated reply for my questions as it would allow me to move forward. I will ensure a good documentation at the end of the process for benefit of other users.
nchary05 said:
Thank you for quick reply. I started compiling the files need to flashing. So far, I could do following. Please advice me whether I am on the right path or not.
1. Rooted my tab with Z4root. Now I got root permission.
2. Downloaded Odin3 v1.7.exe and s1_odin_20100803.pit for flashing
3. Downloaded Roto-JMI-Full-v2.zip and Roto-JMI-Upgrade-v2.zip
Now, using Odin PDA button, I want to flash Roto-JMI-Full-v2.zip ?
Few questions:
a) Is this correct way of flashing or I am missing something?
b) Does above flash install Recovery also ?
c) which files need for PHONE and CSC files ?
MId) Which firmware best suitable for Indian Tab ?
Thank you in advance for clarifying above.
Click to expand...
Click to collapse
Install Adfree or something which requires root acess for installation. Once rooted download something like root explorer from market which allows you to backup the modem.bin file. Or me or somebody else can just upload the file here.
Read the post/link in the thread where you downloaded Roto's JMI rom.
Use the .pit file from Roto's link not the thing which you posted...same place where you got the same ROM file. If you are flashing first time/from another rom then use the Full v2 zip file. Else use Update v2 when flashing from one of Roto's rom.
Connect the tab to your pc, reboot and go into download mode...press power+vol down button while rebooting...a yellow triangle icon with an android digging will come up...to get out of download mode,just keep the power button pressed till it rebooted normally.
Once in download mode, open up Odin and check that the yellow com box option is on. Check repartition option to ensure everything is wiped and you have a fresh install from scratch.
For PIT select the pit file downloaded from roto's link
For PDA select the Full.tar file
For PHONE select the modem.bin file
For CSC leave it blank...
Once done, recheck and hit start.
PLEASE CHECK ROTO'S JMI V2 THREAD IN THE DEVELOPEMENT SECTION...it has a link to howto which is old but gives some idea of how to proceed...for pit, pda, phone follow as I suggested and things will go fine...
Sent from my GT-P1000 using XDA App
Thank you.. I will do the same let you know the status....
blackheart2925 said:
Install Adfree or something which requires root acess for installation. Once rooted download something like root explorer from market which allows you to backup the modem.bin file. Or me or somebody else can just upload the file here.
Read the post/link in the thread where you downloaded Roto's JMI rom.
Use the .pit file from Roto's link not the thing which you posted...same place where you got the same ROM file. If you are flashing first time/from another rom then use the Full v2 zip file. Else use Update v2 when flashing from one of Roto's rom.
Connect the tab to your pc, reboot and go into download mode...press power+vol down button while rebooting...a yellow triangle icon with an android digging will come up...to get out of download mode,just keep the power button pressed till it rebooted normally.
Once in download mode, open up Odin and check that the yellow com box option is on. Check repartition option to ensure everything is wiped and you have a fresh install from scratch.
For PIT select the pit file downloaded from roto's link
For PDA select the Full.tar file
For PHONE select the modem.bin file
For CSC leave it blank...
Once done, recheck and hit start.
PLEASE CHECK ROTO'S JMI V2 THREAD IN THE DEVELOPEMENT SECTION...it has a link to howto which is old but gives some idea of how to proceed...for pit, pda, phone follow as I suggested and things will go fine...
Sent from my GT-P1000 using XDA App
Click to expand...
Click to collapse
I followed the steps after flashing 'full' tar, it rebooted tab, started the normally. After that, I verified that, all applications , phone (GSM) and wifi working fine.
Now my question is do I really need to flash *second* tar file ? what is it for ?
^^No. It is only for people upgrading from previous versions! You are good to go!
Now, I want to install CWM recovery. Please some one can confirm below steps:
1. Make sure to have Samsung Kies installed, and your tab at least connected once, to be sure the drivers are correct.
2. Your Tab must be Rooted.
3. If you wish to do a backup, now is the time.
4. You will need an SD Card with enough free space for the filesystem conversion, and to put the Overcome ROM on before we start. (An empty 4gb should be plenty, as long as it is empty, or close too)
5. Download and Extract the following file to your computer: http://www.apksmash.com/corodius/galaxytab.zip (Contains "Odin3 v.1.7.exe" "Overcome_Kernel_v1.0")
Now, we will Install the Kernel and perform the EXT4 filesystem conversion.
1. Turn off your Galaxy Tab.
2. Turn your Galaxy Tab on into DOWNLOAD mode (Press Volume DOWN and Power On at the same time).
3. Open Odin3 v1.7.exe on your PC.
4. Connect your Galaxy Tab to your PC via the USB cable.
5. Make Sure the ID:COM box is highlighted yellow (meaning it sees your tab).
6. Click on the PDA button and select the Overcome_Kernel_v1.0.tar file you downloaded earlier (make sure PDA is ticked after selecting the file).
7. The only boxes ticked should be:
A. Auto Reboot
B. F. Reset Time
C. The PDA tickbox
8. Click start and wait for PASS! to show highlighted green on Odin.
9. Your Galaxy Tab will Reboot, and get stuck on the Samsung Boot Screen. This is fine.
10. Turn your Galaxy Tab off by holding the power button for about 5 seconds.
11. Turn your Galaxy Tab on into RECOVERY mode (Press Volume UP and Power On at the same time).
12. The Galaxy Tab will now perform the EXT4 conversion.
13. Sit tight, depending on how much data you have, this can take quite a long time.
14. Once finished, click reboot system now (by pressing the power button).
At this point, You have installed the Overcome Kernel with CWM included and converted the Filesystem to EXT4. It has been reported that many stock ROMs will boot and run fine now, however some may not, but it just depends on your ROM etc.
http://forum.xda-developers.com/showthread.php?p=11713685.
Would be there any problem ? or is there any easy way to install CWM Recovery.
I had bricked my tab while modding battery icon and it was not booting now. Now i want to flash with the custom rom available here. I am noob to flashing so just want to confirm the steps mentioned above applicable to the bricked tab. Can somebody guide me for bircked tab.
Please mentioned the good custom rom with Ext4 conversion at the time of install. I am using indian tab.
@OP:- Sorry for hijacking this thread but find some info here for my queries
Can you get into download mode? If yes then you should be able to flash...but I would suggest checking"I bricked my tab" threads in general or developement section...
Sent from my GT-P1000 using XDA App
nchary05 said:
Now, I want to install CWM recovery. Please some one can confirm below steps:
1. Make sure to have Samsung Kies installed, and your tab at least connected once, to be sure the drivers are correct.
2. Your Tab must be Rooted.
3. If you wish to do a backup, now is the time.
4. You will need an SD Card with enough free space for the filesystem conversion, and to put the Overcome ROM on before we start. (An empty 4gb should be plenty, as long as it is empty, or close too)
5. Download and Extract the following file to your computer: http://www.apksmash.com/corodius/galaxytab.zip (Contains "Odin3 v.1.7.exe" "Overcome_Kernel_v1.0")
Now, we will Install the Kernel and perform the EXT4 filesystem conversion.
1. Turn off your Galaxy Tab.
2. Turn your Galaxy Tab on into DOWNLOAD mode (Press Volume DOWN and Power On at the same time).
3. Open Odin3 v1.7.exe on your PC.
4. Connect your Galaxy Tab to your PC via the USB cable.
5. Make Sure the ID:COM box is highlighted yellow (meaning it sees your tab).
6. Click on the PDA button and select the Overcome_Kernel_v1.0.tar file you downloaded earlier (make sure PDA is ticked after selecting the file).
7. The only boxes ticked should be:
A. Auto Reboot
B. F. Reset Time
C. The PDA tickbox
8. Click start and wait for PASS! to show highlighted green on Odin.
9. Your Galaxy Tab will Reboot, and get stuck on the Samsung Boot Screen. This is fine.
10. Turn your Galaxy Tab off by holding the power button for about 5 seconds.
11. Turn your Galaxy Tab on into RECOVERY mode (Press Volume UP and Power On at the same time).
12. The Galaxy Tab will now perform the EXT4 conversion.
13. Sit tight, depending on how much data you have, this can take quite a long time.
14. Once finished, click reboot system now (by pressing the power button).
At this point, You have installed the Overcome Kernel with CWM included and converted the Filesystem to EXT4. It has been reported that many stock ROMs will boot and run fine now, however some may not, but it just depends on your ROM etc.
http://forum.xda-developers.com/showthread.php?p=11713685.
Would be there any problem ? or is there any easy way to install CWM Recovery.
Click to expand...
Click to collapse
I followed above steps and could able to install CWM RECOVER.
congrats dude
maddy_in65 said:
I had bricked my tab while modding battery icon and it was not booting now. Now i want to flash with the custom rom available here. I am noob to flashing so just want to confirm the steps mentioned above applicable to the bricked tab. Can somebody guide me for bircked tab.
Please mentioned the good custom rom with Ext4 conversion at the time of install. I am using indian tab.
@OP:- Sorry for hijacking this thread but find some info here for my queries
Click to expand...
Click to collapse
can you just tel me which modem.bin are u using coz i was planning to flash but stuck on decision bcoz of modem... is it jpz or jk3? or any other
A new GB version is available DDJPA
http://forum.xda-developers.com/showthread.php?t=1226674
need PDA PIT PHONE CSC files
Kindly send me the links for downloading the PDA PIT PHONE CSC files as I could find only broken links.
My samsung tab (Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)) is bricked and won't boot.
Than You
nchary05 said:
Could some one for benefit of Indian Tab Owners, write a step-by-step instructions or guide. Lot of information to digest for a new user including details of 1) rooting 2) installing recovery 3) flashing ... this information would be great useful for everyone.
My Tab details :
(Model: GT-P1000 | Code: INU | Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)
Click to expand...
Click to collapse
I know this is a wide issue on many devices, but i could not find one for the Galaxy Note.
So here it is (and sorry if the answer is allready out there):
i tried to root and it got stuck on bootscreen (the samsung logo). I have figured out (or atleast i thing) that the OS is missing, or something like that. So i downloaded it from a forum page here on XDA. The thing is i can't figure out how to put it on the phone. I tryed using ODIN. Any clue of an easy way to do this?
i have a problem cz i did PIT with u1_02_20110310_emmc_EXT4.pit
and now my phone is stuck but i still can enter download modem and odin read the phone
Thanks in advance
i have N7000JPKK2
Ok so what you do is put sgn pit file in pit in odin choose stock firmware and after flash a cf root kernel which has custom recovery through odin after flashing is done press volume up+home+power button it will load recovery from there select wipe data/app and advance,wipe dalvik cache and fix permissions and then it will boot normally..
Sent from my GT-I9100 using Tapatalk