Hello,
This is my first thread on XDA, because i'm having a problem with my Kaiser.
I'm sorry for my possible "silly" questions, but this a subject wich i'm not very good at.
I have a Kaiser, wich has a TPC Elite Rom Series
R 1.70.19.09
g 25.83.40.02h
d 3.28.00.00
And that runs on WM 6.5
Since last friday while i was configuring my mms settings, the device asked me to restart to assume the new settings. So i closed it down by pressing the power button until the message to "shut it down" appeared.
But when i tried to turn it on again, the device starts with the TPC Elite Rom Series screen, then it appears the data from the rom (mentioned above), then it moves to a screen with the Windows Phone message and logo and it stays here until i turn it off again.
So i cannot start my Kaiser and i need all the help i can get.
Thanks a lot to all of you that can give me a hand.
I already have done hard reset, but it keeps freezing on the "windows phone" screen.
try into three-colour screen and reflash ROM,or look here http://forum.xda-developers.com/showthread.php?t=423486
goodluck!
try into three-colour screen and reflash ROM,goodluck
this is also my first post here, can someone please help.
i tried to hardspl my htc kaiser, and failed miserably. i went through all the steps for hardspl but somewhere failed. during the setup when running the kaiser ruu file.on the cpu it said it was complete and for me to look to the phone to finish setup. on the phone it showed the linux penguin and a list of words scrolling down the screen. then it said error insert sd card. so i did then more words scrolled down the screen. then it said error again then the screen went black. after waiting an hour and nothing happened i took the battery out. then i tried to reload and the att logo would only show up. i read online how to get the tri colored screen back up and i got that by pressing the camera and power and reset button in.on the screen it says
kais1*0
spl-3.56.0000
cpld-8
and it doesnt respond to the computer. how do i re flash and get my phone working again someone please help if you can thank you
Related
Hello guys,
I have an AT&T Tilt since Friday evening and I manged to unlock it and flash it with Dutty's Diamond V1 and HardSPL 3.29 (2 days ago). Everything was fine and today I decided to change my splash screen from the AT&T one to a custom one - that also went well, I soft-reseted the device a few times since. An hour ago, during I was trying to connect to my wireless at home, it just reseted by itself and now I am stuck on splash screen in an endless loop. When I turn it on it vibrates, shows the splash screen, after that shows the versions:
r 1.58.25.17
g 25.69.30.05W
d 3.5 Dutty's
After that it resets and again vibrates... splash screen and so on.
I have tried to hard reset the phone - impossible - the confirmation dialog never appears. I am able to get into bootloader by pressing the camera buton + soft reset and then press power, here is what I see there:
Top: Security Unlocked
in the red color:
KAIS1*0
SPL-3.29.Hard
CPLD-8
Please, help me fix my phone so that I can enjoy it some more than 3 days My previous phone was Nokia 6030... it will be terrible if I have to go back to it
Thanks a lot in advance!!!
Hard Reset. Gonna loose all your data. But it may work.
Fixed
Hi,
I wrote in my previous post that I am unable to get to the hard reset ... but after you wrote that I should hard reset, I thought I'd give it a try one more time... and this time I managed to hard reset (I waited more than 30 seconds until the dialog appeared, before that I was waiting up to t10). And now , what do you know, it booted in windows... Strange thing anyway... Thanks a lot
Ok, I know not everyone will have a similar situation and maybe my post is quite late since many might have moved on to other nicer phones ;-)
I was uploading ROM using ShellTool that takes awfully long and my PC (an XP) decided to download updates and reboot all by itself. Needless to say, I was stuck at the boot screen with the IPL, SPL, GSM and the OS screen. The OS was showing 6.0.0.1 and that's it. pressing the Voice Dial and COMM button and resetting didn't help. So out of frustration, I pressed the Camera and Voice Dial buttons and did a reset and Presto, got the Red, Green, Blue with USB screen. I was able to load ATT's WM5 on it. Am sure many will like to know this minor pleasant mishap.
Hard Reset is mentioned here http://www.pocketpccentral.net/help/cingular/8125reset.htm
I would call my trick as the Hard Wiping
ak2k8 said:
Ok, I know not everyone will have a similar situation and maybe my post is quite late since many might have moved on to other nicer phones ;-)
I was uploading ROM using ShellTool that takes awfully long and my PC (an XP) decided to download updates and reboot all by itself. Needless to say, I was stuck at the boot screen with the IPL, SPL, GSM and the OS screen. The OS was showing 6.0.0.1 and that's it. pressing the Voice Dial and COMM button and resetting didn't help. So out of frustration, I pressed the Camera and Voice Dial buttons and did a reset and Presto, got the Red, Green, Blue with USB screen. I was able to load ATT's WM5 on it. Am sure many will like to know this minor pleasant mishap.
Hard Reset is mentioned here http://www.pocketpccentral.net/help/cingular/8125reset.htm
I would call my trick as the Hard Wiping
Click to expand...
Click to collapse
It's not a trick, it is called the RGB bootscreen.
not same as RGB, the actual boot.
well, all I got stuck was at the boot screen, not the RGB screen, the screen that just shows the IPL, SPL, GSM and OS numbers with the Cingular screen. I did not find anywhere that showed me to get out of the screen till I accidentally came across it. Actually, the record button is not necessary, just the camera button is fine while pressing the reset and holding it till the RGB screen is back.
Where did you get AT&T's WM5 rom, I am having the same problem. I have the IPL/SPL but can't find the rom, the link in the thread here no longer works.
Thanks.
Hello peeps, my first thread as you can see and also a beginner to this Xperia phone!
Well, yesterday night I downloaded an upgrade through the "Windows mobile device center". I did exactly as it said, I followed the instructions and it did get complete. I was able to start the phone without any minor problems.
After a lil while when I did shut down the phone and tried to start it, it did start. I got to the sony ericsson logo and and 2 more stuffs after.
After the logo it said something similiar to "Click on the screen if you want to configure your windows mobile device" and something more. I clicked on the screen and I got somewhere where you have to point at a "plus" four times (through the whole screen), and to the problem it always reset at the same point tellin me to do the same thing!
It pisses me of, so please could any1 please try to help me.
I bought the phone yesterday!
When I push the lower sound and turn on button I get some info saying:
KOVS110
SPL-0.78.0000
MicroP1-787
MicroP2-707
I have also tried to do a hard reset which is not possible anymore, only yesterday (two buttons down there and on/off together?) and I also did that thing where you have to put a stick beside the battery.
Yours. Freak
Fixed!
Please remove this thread.
Hello,
This is my first thread on XDA, because i'm having a problem with my Kaiser.
I'm sorry for my possible "silly" questions, but this a subject wich i'm not very good at.
I have a Kaiser, wich has a TPC Elite Rom Series
R 1.70.19.09
g 25.83.40.02h
d 3.28.00.00
And that runs on WM 6.5
Since last friday while i was configuring my mms settings, the device asked me to restart to assume the new settings. So i closed it down by pressing the power button until the message to "shut it down" appeared.
But when i tried to turn it on again, the device starts with the TPC Elite Rom Series screen, then it appears the data from the rom (mentioned above), then it moves to a screen with the Windows Phone message and logo and it stays here until i turn it off again.
So i cannot start my Kaiser and i need all the help i can get.
Thanks a lot to all of you that can give me a hand.
carluchu said:
Hello,
This is my first thread on XDA, because i'm having a problem with my Kaiser.
I'm sorry for my possible "silly" questions, but this a subject wich i'm not very good at.
I have a Kaiser, wich has a TPC Elite Rom Series
R 1.70.19.09
g 25.83.40.02h
d 3.28.00.00
And that runs on WM 6.5
Since last friday while i was configuring my mms settings, the device asked me to restart to assume the new settings. So i closed it down by pressing the power button until the message to "shut it down" appeared.
But when i tried to turn it on again, the device starts with the TPC Elite Rom Series screen, then it appears the data from the rom (mentioned above), then it moves to a screen with the Windows Phone message and logo and it stays here until i turn it off again.
So i cannot start my Kaiser and i need all the help i can get.
Thanks a lot to all of you that can give me a hand.
Click to expand...
Click to collapse
I think you just need to get a hard reset the device only
Thanks for your help.
I've already done several hard resets, but after trying to restore and when i press "send" to boot, it starts but it always keeps stuck at the "windows Phone" screen.
Help, anyone?
Thank you
put it into boot loader mode and flash another rom
Hi, I'm new to XDA Dveloper. sorry if its already questioned..I don't have time to search for them, I'm running my laptop on battery that only will last about 15 minutes..and I have my electricity out..
Yesterday, I got My diamond exposed to water...it was raining hard and I was on my bike with my diamond in my pocket..
when I got home, my diamond begin to act strangely, it keeps lower its volume(to vibrate state) when I try to press the increase volume rocker, it goes back down to vibrate. but I manage to shut it down with slide2shutdown...and charge it (the battery only 7% left). this morning I get up and switch on the diamond, but It doesn't boot like usual(theTOUCHDiamond sceen)...
it only shows 4 bars (RED, GREEN, BLUE, and WHITE)consist of:
RED BAR with this:
DIAM100 64M
SPL-1.37.Olinex
MicroP-Diam (LED) v11
GREEN Bar with:
PSOC-Diam Stage_PVT v0x30
BLUE Bar : blank
WHITE Bar with
Serial (only "serial is written, nothing more)
That all, and when I try to connect with USB cable, it demands Qualcomm CDMA Drivers...(I use My friend's laptop....no activesync installed)
anyhelp would be appreciated.
thanks
Its strange..., Now my phone could boot normally, but the volume control still error..it keep decreasing( i tried to increase it but it keep getting back to 'vibrate' is this becaus the water?
EDIT: I'm sorry...its still the same, if I restart the device..it shows the 4 colored bars screen again. when I try to reset it, 1 of 10 attempts is likely that diamond boot normally..but the volume error is still there...can sum1 help me?
PS: Sorry, I don't know that I could edit my post..
bellsprout said:
Its strange..., Now my phone could boot normally, but the volume control still error..it keep decreasing( i tried to increase it but it keep getting back to 'vibrate' is this becaus the water?
EDIT: I'm sorry...its still the same, if I restart the device..it shows the 4 colored bars screen again. when I try to reset it, 1 of 10 attempts is likely that diamond boot normally..but the volume error is still there...can sum1 help me?
PS: Sorry, I don't know that I could edit my post..
Click to expand...
Click to collapse
what are you trying to hardreset device..??
A hard reset should only be performed if a normal reset does not solve a system
problem. After a hard reset, the device is restored to its default settingsā
the way it was when you first purchased it and turned it on. Any programs you installed, data you entered, and settings you customized on your device will be lost. Only Windows MobileĀ® software and other pre-installed programs will remain.
Try flashing back to stock rom?
Sent from my GT-P1000 using XDA App
Hi!
I have a boot problem also.
I used Memo ROM about 1 month ago. That was worked well still today. I restarted my Diamond today, it was not boot correctly. Only reboot the phone after showing the ROM information. I made hard reset and put back the rom again, but the phone is not boot properly.
Could to help somebody for me?
I solved the problem.
I downloaded the original rom (included with radio rom) from htc.com.
I put the phone to bootloader mode and flashed this original ROM.
After flashing finished, my diamond boot to WM6.1.
I don't know what was the problem, but it works again...
I hope never happening this again!