dear all
i have tried everything and i think i bricked my phone.
my phone have no iemi number and the firmware info are :
PDA : I9000JPJPG
Phone : Unknown
CSC : I9000OJPJPF
Odin wont recognize the download mode so i cant flash stock rom
the problem is the phone wont recognize the simcard , everything else is normal.
i have clockworkmod recovery, tried flashing different roms and radios still nothing. it also gives me baseband unkown. what should i do???
the problem is the phone wont recognize the simcard , everything else is normal.
Is that due to you installing a rom that does not have your network
in which case in the settings manually add your Networks details apn etc .
jje
Try see if your clockwordmod has any backups? Usually when doing changes it does make a full system backup..
If so, try restore from there, it should also restore imei
Not forgetting your backed up efs folder can be replaced if you did back it up most ignore that faq .
Mine came back with install of a new rom .
jje
areenchem said:
dear all
i have tried everything and i think i bricked my phone.
my phone have no iemi number and the firmware info are :
PDA : I9000JPJPG
Phone : Unknown
CSC : I9000OJPJPF
Odin wont recognize the download mode so i cant flash stock rom
the problem is the phone wont recognize the simcard , everything else is normal.
i have clockworkmod recovery, tried flashing different roms and radios still nothing. it also gives me baseband unkown. what should i do???
Click to expand...
Click to collapse
I had the same thing, I had to use the 3 button method and used Odin but remember that you have to have Odin running before you connect your phone to your USB connection and you should also have your phone in Download mode using the 3 button method before connecting it to your USB connection. Otherwise Odin won't recognise it, Also you need to make sure you have the phone drivers on you PC.
I just downloaded a stock firmware from samfirmware.com and that installed brought it back to how it was when I bought it. (Fully functional) and then I tried again with rooting it and lagfixing it. works fine.
The reason why mine died in the first place was because I didn't wait long enough on the first boot after the flash and I had thought it had frozen when it was really still just writing new information to the hardware so remember to be patient on the first boot after the flash.
It seems your phone Modem part is not flashed properly thus you could not retreive the IMEI from this part.
Suggestion:
Try to locate the original ROM which comes with this phone and flash it again and check if this works. From this start from zero
Couldn't you flash the modem via clockworktecovery if odin doesn't work? Much more simple if the missing modem is the problem. Modems can be found via docs thread.
Sent from my GT-I9000 using XDA App
lost IMEI
If you are not even getting Odin to connect to your phone, your bootloader must be corrupted. If the phone can get into APX mode, you can flash new bootloader and start off from there.
Connect device to Windows PC and see if Windows would detect the device to start with
Related
Hi!
After searching the forums for a while I did not find a thread exactly matching my problem, so if I've overseen it, please just point me there.
To my problem:
I did a very stupid mistake, flashing a new custom ROM with a different kernel (as usual, cooked in Docs Kitchen) without converting back the lagfix. So I ended up with a non-booting phone - so far, so bad. Note to myself: Never flash a phone during the carnival weekend again.
So I booted into download mode and tried to recover it via Odin, but here I got my really bad surprise: USB device is not recognized, thus I Odin does not see the phone.
I tried 4 different PCs with Win7 or XP, a Linux desktop and a Macbook. I also tried 5 different USB cables (they all work with other smartphones like the Desire and the HD2). Wherever I stick the phone in, it is not recognized (code 10/code 43 in Win7). I used the stand-alone-drivers from the sticky forum thread here, and also most recent Kies versions, always the same: USB device not recognized.
Does anybody have an idea how to revive the USB connectivity? I'm almost at the point to send it in for repairs...
Or can someone elaborate how I could have killed USB with corrupting the ROM? I've to admit I do not really understand how these two are connected.
--Jens
Hi Amokbunny
You get into download mode but the PC won't recognize the phone?
That's messy and I can think of nothing that could have done that. you did not change the bootloader did you (flashed a full samsung ROM containing a bootloader, for example VJ1)?
If not I guess it's a hardware issue.
formatted to ext4 without any backup
I did a very stupid mistake too. Got darky's rom 9.3., installed i, everything worked great(really awesome thing), then i wnt to recovry mode and entered tthe speedmod and it showed mr that my phone has rtf files system not EXT4 as it should be, thou i installed the speed mode. then i chose to repartition it to ext4 but i didn't choose the backup. Just clicked to format the sd. It did formatted to EXT4, rebooted, i saw the darky's rom logo and the the phone vibrated and the logog of the droid just flashed. I tried to enter recovery mode-didn't load. Started the download mode connexted to pc used ODIN 1.7 with PDA I9000XXJPY.tar, MODEM I9000XXJPY.tar, GT-I9000-CSC-MULTI-OXAJPY-LITE.tar s1_odin_20100512.pit.
The phone has started, appeared teh stok galaxy s logo and it's just flashing. Help needed. Don,t know what to do know. I have galayx s i9000 european version.
somehow i've managed to install new firmare 2.2.1 /I9000XXJPY-baseband /2.6.32.9 [email protected] #1-kernel version, but z4root isn't working. When i start permanent root the programm ends on aquiring root shell, the debug mode is on
Got it all running, installed Darky's rom 9.3. Thanks anyway.
theduckking said:
Hi Amokbunny
You get into download mode but the PC won't recognize the phone?
That's messy and I can think of nothing that could have done that. you did not change the bootloader did you (flashed a full samsung ROM containing a bootloader, for example VJ1)?
If not I guess it's a hardware issue.
Click to expand...
Click to collapse
Yep, I can boot into download and recovery modes, but that's it.
The only apparent change in the new custom ROM was the kernel.
I also cannot really access my external SD card (it shows me some phantom files, but not the actual content of the SD), otherwise I'd try to recover it this way.
I agree with the hardware issue, if it wouldn't have coincided with the flash procedure...anyway, I think I'll send it in for repairs if I don't get it to run on this sunday.
I have the exact same problem, except that I can access my external SD. I got the problem after upgrading to Darkys Rom 9.3 the usual way, but switched from Speedmod to Voodoo. After that update, my USB didn't work anymore.
I can't get neither Xp or Win 7 to recognize my phone. USB device not recognized, and tried all the tricks. Reinstalling Kies and drivers, switching between the different modes (storage, kies media, ask, debug...) But still no USB connection.
I updated to darkys 9.5 (transferring the rom using bluetooth, and updating using CWM), but still it doesn't work.
Can get it into download mode, but still can't connect using USB and Odin.
HELP!
Did anybody ever find a solution for this?
European version of I9000, bought in Denmark. No Simlock
Same thing here after installing JV1 + Ultibread Rom 1.4... Still no solution
*shameless push*
Any solution here? I dont have that problem, but it sounds too scary to not have a working solution :S
Same prob here! Any news?
Any solution? I have the same problem.
same problem my phone is bricked while flashing a stock rom the windows disconnected the phone while flashing
ended with device not recognized even in download mode
bassem8246 said:
same problem my phone is bricked while flashing a stock rom the windows disconnected the phone while flashing
ended with device not recognized even in download mode
Click to expand...
Click to collapse
But if you are in download mode on your fone you'd rather should have a look at your configuration on the computer. Because the fone still can be flashed if the symbol for download still appears.
- Kies is shut down while ODIN is active?
- latest Samsung USB driver installed?
- Odin started with Admin?
Btw. did you try to get into recovery mode? Maybe this also still is working as the partition is quite small and chance high that it was flashed w/o faults. So you may be able to flash a zipped ROM rather than a tarball for Odin.
USB Not working when Phone plugged in... try these..
Unplug Device from PC..
Windows go to Device Manager...
Scroll down to Universal serial bus Controllers
Start with the top one and work your way down ..uninstall them all..
When done reboot Computer and let it install them all.. then try again
2.Settings --> USB Setings (under wireless & network may differ depending on Rom used) --> Try other settings Mass storage
3.Different USB ports on PC
4.Uninstall KIES from PC (reboot PC to take effect) and Reboot and just install samsung USB drivers....
5.Using windows type in msconfig in Start>Run box... windows will pop up and untick KIES from STARTUP TAB
Apply to take effect and restart machine.. try using ODIN to Flash ROM
I myself only use the Samsung USB drivers and ODIN never use KIES
or ...Check my signature and try SD formatter
Hi everyone
So here it is : No program is able to recognize/detect my Galaxy S i9000M (Bell Vibrant) when it's in download mode, so I can't flash any ROM. My phone is currently fully bricked and unusable. I cannot access to the recovery mode with the three-button thingy or by "adb reboot recovery"
I bricked using Odin 1.8, trying to flash a 2.2 froyo stock ROM from Samfirmware. The flashing went ok, but it failed to reboot. Actually, the screen was turned off and nothing was happening. I figured out it was fully bricked so I made a USB JIG, it worked. I can access my download mode.
I connected the phone to my Windows 7 computer and used Odin to flash back to 2.1 Eclair, with a stock ROM from Samfirmware. It failed (I don't remember the error message, it was a couple days ago...).
I tried with Heimdall Frontened. It had a problem uploading the .pit file, so the flashing didn't work.
Now each time i connect the phone to my computer, Windows (and Heimdall frontened and Odin) doesn't detect it,which means that I can't flash anything on it even though it is in download mode.
I have tried reinstalling like every driver on earth, still not responding.
I tried on another Windows 7 machine and on Ubuntu, the device is not detected.
I tried with different USB cables, nothing happens.
This is my hypothesis (maybe silly) : Could the problem be the Download mode being corrupted?
Whatever... I could use some help from you guys.
Thank you,
Sam
I had/have the same problem.
I installed the Samsung Kies and now my computer recognize my phone again.
But I have still no idea what I need to flash to make my phone working.
goldsage said:
I had/have the same problem.
I installed the Samsung Kies and now my computer recognize my phone again.
But I have still no idea what I need to flash to make my phone working.
Click to expand...
Click to collapse
That is strange... I tried installing Kies and it didn't detect the phone. And you could just flash any 2.3 stock ROM with Odin I guess.
Hi there.
I have flashed my Note several times.
Wanting to install stock Hong Kong firmware I downloaded the firmware while on my Mac and then Bootcamped it to Windows to use Odin.
At the time on reboot, my Note was connected to USB on my Mac.
When rebooting, my Mac got stuck at black screen before the Windows logo.
Didnt get what was going on I tried reboot several times.
Realised that it was trying to read off of USB devices that was connected as a first bootable.
As soon as I disconnected the Note USB cable it booted to Windows.
But now my Note wont get recognised.
Both Windows or Mac.
The Note charges the batteries through USB (PC or its mains adaptor) but doesnt get recongnised as mass storage even....
Help..!
Does rebooting phone and computer help?
Markuzy said:
Does rebooting phone and computer help?
Click to expand...
Click to collapse
no....
USB doesnt repond in recovery or download mode.
i get message saying unrecognizeable...
I have used Odin so many times in the past...
tried reinstalling drivers tried on another machine.
Must be the phone... but how..? any idea on how to fix?
even if i was to get it serviced, I have Miui on it at the moment....
Not sure if it works, but on a different Samsung phone on MIUI, they fixed it by downloading Nexus S drivers:
http://forum.xda-developers.com/showthread.php?t=1029313
pc odin not working u still got Mobile odin to flash it.
go get ur version a safe kernel http://forum.xda-developers.com/showthread.php?t=1901191
do a backup n a special backup of efs that will help u when things went wrong.
use the lastest Mobile odin to flash the rom u want in ur external sdcard.
alvinhaw said:
pc odin not working u still got Mobile odin to flash it.
go get ur version a safe kernel http://forum.xda-developers.com/showthread.php?t=1901191
do a backup n a special backup of efs that will help u when things went wrong.
use the lastest Mobile odin to flash the rom u want in ur external sdcard.
Click to expand...
Click to collapse
Thanks.
I've never used mobile odin.
I can install Stock firmwares through mobile Odin too?
But still problem is that phone isnt recongisable. even for mass storage...
So moving files will be pain in the ass.
Any solutions?
you need an external SD to to transfer the stock rom (tar.md5) files to it. then use mobile odin to flash the firmware. Mobile Odin can flash stock firmwares
nokiamodeln91 said:
you need an external SD to to transfer the stock rom (tar.md5) files to it. then use mobile odin to flash the firmware. Mobile Odin can flash stock firmwares
Click to expand...
Click to collapse
Thanks. Done it.
But now I am stuck with Ginger Bread.
It wont allow me to update to ICS through OTA because I am not on Hong Kong network.
Now trying to find a way of rooting it without the need to tether my phone to the PC.
Started new thread about it but no luck.
I don't really need to have ICS since its not for my own use (the Note) but it will be nice.
But seriously, how can I fix the USB problem?? Any body faced the same thing?
may be the usb port is faulty.. if you can get it repaired by samsung. well and good. if no then these are available for online purchases ... a do it yourself tutorial
http://www.youtube.com/watch?v=N6CJy71_9Ok
Fixed
lol.
It just fixed itself few days after.
still didnt risk using Odin.
Used KIES. it worked. Now have LRB ICE Chinese.
Hello.
I recently installed CM10.1.3 on my GT-I9000 running stock GB. I did everything according to the instructions (though, mind you, this was not my first time installing a ROM just the first time on this device).
When I booted and tried to set up a CM account it gave me a message saying "Insert SIM card". I tried installing the kernel again, as well as installing other ROMs (AOKP mostly).
Nothing seems to work. It will simply not recognize my SIM.
Any suggestions?
Thanks!
Tal
LaDjA said:
just the first time on this device).
Click to expand...
Click to collapse
since its the first time on this device, can you check IF sim card is inserted in the correct direction
Check this out! You , YES! you are an " Android ". Not your phone but U.
Yes. It is.
Might be also worth mentioning that I tried it with a few different cards, all of which work with other devices, and not with this one.
LaDjA said:
Yes. It is.
Might be also worth mentioning that I tried it with a few different cards, all of which work with other devices, and not with this one.
Click to expand...
Click to collapse
you can try taking it back to stock ROM , you can follow this but it sounds like you may have hardware problem, if that fails as sim contacts can get broken or damaged too and can be replaced. so best to test with Stock ROM to check if its a software or hardware problem. also try to flash without SIM card and insert after flashing and first boot.
Check this out! You , YES! you are an " Android ". Not your phone but U.
LaDjA said:
Hello.
I recently installed CM10.1.3 on my GT-I9000 running stock GB. I did everything according to the instructions (though, mind you, this was not my first time installing a ROM just the first time on this device).
When I booted and tried to set up a CM account it gave me a message saying "Insert SIM card". I tried installing the kernel again, as well as installing other ROMs (AOKP mostly).
Nothing seems to work. It will simply not recognize my SIM.
Any suggestions?
Thanks!
Tal
Click to expand...
Click to collapse
For a clean install and root, flash JVU ROM and its CF_root, as it is easy and problem free. I never had any problem with JVU
The whole procedure is given below
FLASHING JVU ROM WITH ODIN v1.85:
1. Install USB drivers for i9000 on PC (ignore if already installed) and restart computer to take effect
2. Turn off your phone and put it in download mode
by holding VOL DOWN+MENU+POWER
Do you get the Yellow Triangle?..If so
continue..if not do it again...
3. Plug in Phone with USB Cable To Computer.
4. In ID:COM it should go yellow and you should see
ADDED in the message box
5. Check Re-Partition option and then Click PIT
button to select: s1_odin_20100xxx.pit file.
6. Click PDA button and select :
CODE_I9000XXJVU_xxxxx.tar
7. Click PHONE button and select:
MODEM_I9000XXJVU_xxxxx.tar
8. Click CSC button and select:
GT-I9000-CSC-MULTI-OXAJVU.tar
9. When you have all the files needed in ODIN,
Click Start and let it Run
10. Once complete you will see S logo on phone
(computer will make a few noises like connect/
disconnecting
11.Unplug the Cable to the Phone
You will see your phone working excellent. Now it's time for rooting
Procedure for rooting:
1. Power Off Phone
2. Download CF-Root kernel first.
Unzip the file to a folder. You
will get the .tar file – CF-Root-
XX_OXA_JVU_2.3.6-v4.3-CWM3RFS.tar
— inside the extracted folder. DO NOT extract
the .tar file (even if you see it as a zip
file, which it is not). You need to flash
the .tar file using Odin to gain root
access and install the ClockworkMod
Recovery (CWM) alongside. If you’re
getting zimage file, it means you’ve
extracted the .tar file too! — and that’s
not a right thing to do.
3. Boot your phone in Download Mode —
Press and hold volume down+HOME
+POWER keys together.
4. Open Odin now. Connect your phone to PC now. You’ll notice “Added! !” message in the Odin’s message box in the bottom left.
5. On Odin, click the PDA tab and select the .tar file you got in step 2 — CF-Root-XX_OXA_JVU_2.3.6-v4.3-
CWM3RFS.tar
6. Make sure “Re-Partition” checkbox is not selected. Leave the “Auto Reboot” and “F. Reset Time” checkboxes selected.
7. Click the Start button on Odin to flash the CF-Root kernel. After the CF Root is installed, phone will restart automatically. When you see the PASS written in top left box, you can remove the cable.
8. Your phone is rooted now. That surperuser app is there! The CWM app is also there, and
clockworkmod based recovery has
been installed too. Now you enter the custom ROM world without worries. Enjoy!
PIT File DOWNLOAD Iink: www.mediafire.com/download/v2rub40k1bvccj4/s1_odin_20100512.pit
ODIN 1.85 download link:
www.mediafire.com/download/82latn22s1kl7w2/andromint-Odin3-v1.85.zip
XXJVU Download link:
(password: samfirmware.com)
hotfile.com/dl/140301534/be8872c/I9000XXJVU_I9000OXAJVU_OXA.rar.html
CF_root download link:
download.chainfire.eu/132/CF-Root/SGS/CF-Root-XX_OXA_JVU_2.3.6-v4.3-CWM3RFS.zip
If you don't have USB drivers, then download below
Samsung USB drivers:
www.mediafire.com/?hzlnda0l5t8qyes
xsenman said:
it sounds like you may have hardware problem, if that fails as sim contacts can get broken or damaged too and can be replaced.
Click to expand...
Click to collapse
But the hardware was functioning perfectly well before I flashed. Why would flashing a ROM damage my SIM contacts? (or any hardware, for that matter)?
xsenman said:
you can try taking it back to stock ROM , you can follow this
Click to expand...
Click to collapse
In this guide, when I am trying to download the PIT file, it wants me to log in with my google\facebook account. Something about that smells fishy. Are you sure it's reliable enough? Alternatively - could you provide a different download link for the file?
Rohitdahiya said:
XXJVU Download link:
(password: samfirmware.com)
hotfile.com/dl/140301534/be8872c/I9000XXJVU_I9000OXAJVU_OXA.rar.html
Click to expand...
Click to collapse
The password doesn't match, or so peazip says. I can't get the file to extract.
Thank a lot, guys, for all your efforts.
LaDjA said:
But the hardware was functioning perfectly well before I flashed. Why would flashing a ROM damage my SIM contacts? (or any hardware, for that matter)? In this guide, when I am trying to download the PIT file, it wants me to log in with my google\facebook account. Something about that smells fishy. Are you sure it's reliable enough? Alternatively - could you provide a different download link for the file?
Click to expand...
Click to collapse
I assume you have a software issue, that's why I asked you to revert to Stock ROM after you confirmed the SIM card was not inserted the wrong way round. , only IF the sock ROM also gave you that result than you need to consider hardware, as I have not heard of anyone having this issue after flashing CM 10.
AS for PIT file its in 4Shared site, all they would require is you should be a member and register with them ( you can do that with any name and password) the ROM site is FileRio, there you should only use free download button , clicked a number of times ( same button) for download to begin, both uploads were by me, so its virus free. I will upload pit file to the thread asap as its very small file.
EDIT: already uploaded PIT File to thread uploaded 3 PIT files in a package used for i9000, only use 512
Check this out! You , YES! you are an " Android ". Not your phone but U.
Hey. Thanks again.
One more problem, and it's a big one:
Odin won't respond to my device. No yellow rectangle, or any kind of response...
What can I do to make it realize that it's there?
LaDjA said:
Hey. Thanks again.
One more problem, and it's a big one:
Odin won't respond to my device. No yellow rectangle, or any kind of response...
What can I do to make it realize that it's there?
Click to expand...
Click to collapse
the guide to solve such problems is right on top (begining) of that thread
Note:- It's assumed that you can and know how to connect your Phone to PC with USB cable . If you do not know, first install Samsung USB drivers on your PC/Laptop, than enable USB debugging on your phone by settings menu>Developer options> tick USB Debugging. After this use only Samsung USB cable and plug it into your phone micro USB port and to your PC USB Port. ( Always use the Back USB port on PC as some ports may not connect well enough for flashing ROM's. )
If unable to connect your phone to PC for any reason, refer to this guide
Click to expand...
Click to collapse
Check this out! You , YES! you are an " Android ". Not your phone but U.
I tried everything in that guide, and it still the same.
Might be worth noting that the computer totally does recognize the device. I mean, I can access the internal SD from the computer, when the phone is on. It's just that when I connect it in download mode, Odin doesn't respond.
Might also be worth to stress that I used Heimdall to flash the recovery, when I did it. Could it be related to why I can't use Odin now?
And another thing regarding my main issue - could the "Insert SIM" message be a modem thing?
The password for XXJVU is samfirmware.com
If you are still unable to open this, then download XXJVU by Google searching and then try. This is the best way to get rid of the problem.
If you are able to go to download mode, install USB drivers for Samsung and restart PC . Now exit the Kies program and its related services from your PC. If you are using windows, you may find the tray icon and exit by right clicking. Now run Odin and flash.
If you are not able to go to download mode then search "homemade usb jig" and use the jig method described in those threads.
I'm trying to download the XXJVU again. Will see how goes.
I am able to go to download mode. So that's not it. I also don't have Kies installed on my computer, so that's also not it. I installed a few different Samsung drivers, and did the whole process a few times. The computer always recognizes the phone, but Odin doesn't.
I don't get why I can't delete stuff, if I accidentally posted twice. Anyway - feel free to disregard this one. Sorry for spamming..
OK. Managed to open the XXJVU.
Still have the problem with Odin not paying attention to my phone being there. Do you think it might be a problem with dl mode, that I should try fix with a jig (the phone does act LIKE it in dl mode - yellow triangle and all...)?
LaDjA said:
OK. Managed to open the XXJVU.
Still have the problem with Odin not paying attention to my phone being there. Do you think it might be a problem with dl mode, that I should try fix with a jig (the phone does act LIKE it in dl mode - yellow triangle and all...)?
Click to expand...
Click to collapse
You seem to be having strange problems. I assume you pressed the correct combo keys ( as shown in image on that thread) and you did not get download mode ( this could be due to ) you don't have an i9000 but a different version of Galaxy S? or your keys are not functioning or you have a wrong bootloader
so use this methods & tool from PC to boot into download mode after you are sure you have an i9000 international version by checking under the battery. just to give you an idea , read this
Odin will only connect when phone is in Download mode, so as you mentioned you have NO problem with drivers and PC, its only your phone not being able to enter download mode.
Check this out! You , YES! you are an " Android ". Not your phone but U.
xsenman said:
You seem to be having strange problems. I assume you pressed the correct combo keys ( as shown in image on that thread) and you did not get download mode ( this could be due to ) you don't have an i9000 but a different version of Galaxy S? or your keys are not functioning or you have a wrong bootloader
Click to expand...
Click to collapse
You assume correctly - I did use the correct combo. And the battery says I have an GT-I9000. I think that's only the int'l version, isn't it?
xsenman said:
so use this methods & tool from PC to boot into download mode after you are sure you have an i9000 international version by checking under the battery. just to give you an idea , read this
Odin will only connect when phone is in Download mode, so as you mentioned you have NO problem with drivers and PC, its only your phone not being able to enter download mode.
Click to expand...
Click to collapse
I will try the ADB solution tomorrow. But doesn't the fact that the phone displays the download mode screen say that it is indeed in that mode? (because it does display it, as I mentioned above). I mean - is it possible that the phone seems like it is in download mode, when it's actually not?
Thanks!
LaDjA said:
. But doesn't the fact that the phone displays the download mode screen say that it is indeed in that mode? (because it does display it, as I mentioned above). I mean - is it possible that the phone seems like it is in download mode, when it's actually not?
Click to expand...
Click to collapse
hmm, i got the impression that you are not getting the download mode display , if it does than it is in download mode, so now you need to check your Odin3 download, what version are you using , try and download again and always use fresh Odin3, meaning, if it had a problem or even when no problem restart it a fresh. And best install Samsung USB drivers again ( link on that thread), if that did not solve it.
Check this out! You , YES! you are an " Android ". Not your phone but U.
I tried both versions that from here (i.e. v1.83 and v1.85). I'm not really doing anything else with Odin, so there's nothing to restart.
I also tried uninstalling and installing the drivers a few times, using a few different installation files, and by letting windows figure out on its own which drivers to install.
Non of it changed the result.
LaDjA said:
I tried both versions that from here (i.e. v1.83 and v1.85). I'm not really doing anything else with Odin, so there's nothing to restart.
I also tried uninstalling and installing the drivers a few times, using a few different installation files, and by letting windows figure out on its own which drivers to install.
Non of it changed the result.
Click to expand...
Click to collapse
this is weird, anyway since heimdall is possible, right? try and download a heimdall rescue kit from MY Android collections and try flashing , if the phone boots you can also install Mobile Odin from playstore to flash stock ROM too.
Check this out! You , YES! you are an " Android ". Not your phone but U.
hello m8's
Long story short: my beautiful international version GT-I8910 has died on manual update of firmware. I have never tried to update to other rom's, custom or no custom, i never tried USB Debugging, recovery or anything else. The phone is stuck at : see picture 1, i am not able to get into recovery, in kies update i'm beeing asked for recovery code, only can acces Download Mode. I'v tried another stock rom from sammobile.com, i've tried every wipe etc. On Odin i got this error: see pic. 2. In Download Mode somewere in the left down corner i had "HW REV : 0x5""
Ooo..and Odin give my FAIL.see pic 3
Guys..i'm crying..please help...
are you flashing the correct firmware from sammobile, if not will fail, try a different usb port & make sure fone is recognised in "ID:COM" window & flash as pda
i'm flashing the correct rom...in odin it says Added...at sistem.img write give me Fail error... (
LE: 1) Is there a way to do a full system, app and file backup using adb commands? 2) Is it possible to enable USB Debugging via methods using adb commands?
alex1982 said:
hello m8's
Long story short: my beautiful international version GT-I8910 has died on manual update of firmware. I have never tried to update to other rom's, custom or no custom, i never tried USB Debugging, recovery or anything else. The phone is stuck at : see picture 1, i am not able to get into recovery, in kies update i'm beeing asked for recovery code, only can acces Download Mode. I'v tried another stock rom from sammobile.com, i've tried every wipe etc. On Odin i got this error: see pic. 2. In Download Mode somewere in the left down corner i had "HW REV : 0x5""
Ooo..and Odin give my FAIL.see pic 3
Guys..i'm crying..please help...
Click to expand...
Click to collapse
Bring to the Samsung Service Center, and pay for it.