[Q] new digitizer doesn't work - Touch Diamond2, Pure Q&A, Help & Troubleshooting

I bought and installed new digitizer and it won't work. I did hard reset and also ran align screen via Pocket Controller-Pro. What can be wrong?
thanks in advance

and me.. I bought a new digitizer cheap, is working but when you cross the finger along the screen you hear a sound in the digitizer and the touch is not responsible as the old.. so i have to buy a new one ''original''..

Hi iasi_me
Where did you buy original digitizer and how much did you pay for it? I bought my on ebay.co.uk and i was told it's original (OEM).

I found here in romania a little gsm store and i pay about 21 euro , but be careful if it's cheap is perfect visual but not perfect functional, (sorry I don't speak very good english)
but go to a gsm store and ask somebody to help with the problem

Hi Buddys,
and often you have to look closely at the little "Flat-Cable". Cheap new Digitizer are a littebit different as the Original one. When you install the little Flat-Cable" you have to turn theses maybe 180 Degrees. Otherwise when you use your new Digitizer the Touch-Response is complete wrong. e.g. you type on the Digitizer "in the upper Part" the Digitizer told the Diamond 2 PCB it´s in the lower Part ( and there on the other side ). This is the Indicator for this 180 Flip !
Everytime when you install a cheap new one you have to put the 4 Pin SMD-Connector correct. This means--->The 4 Pins have to show to the PCB like the Original HTC-Touchscreen.
Here´s a Picture from the Original Digitizer:
://mperlitsch.hintergrundbild.com/htc_diamond2/BILD11.jpg
If the cheap Digitizer shows the 4 Golden Pins to the Sky, turn this Clone-Digitizer 180 Degrees and be very gentle, because the Flex-Connector is very sensitive. Here a Trick: If you have this kind of Digitizer you have to connect that Connector before (!) you put the PCB Back in Place. After Connection und Locking the Cable in Place with the SMD-Connector you have to Turn only the PCB 180 Degrees and put this wired in Place.
If you need more Fotos and Instruction for Replacing a Diamond 2 Touch look here:
://mperlitsch.hintergrundbild.com/htc_diamond2.htm#Touchscreen
There is a Big Section and a lot Pictures for Replacing the Digitizer ( it´s in German, but Pictures say more then 1000 Words....sometimes ;-) correctly and safe...
So long,
Michael

Thanx Michael for such a great and very helpful site. I turned the digitizer connector 180 degrees and it didn't help. I think i'll need one of the original digitizer from htc.

Related

How to replace the Digitizer/Touch Panel? any body?

I have looked everywhere but no luck! Can someone please give clear instruction how to replace the digitizer/touch panel?
I have only found instructions how to disassemble the diamond up to the LCD stage only! But after that it does not show how to take the LCD out of the housing to expose the Digitizer.
Hope someone knows how to do it.
Thanks.
The instructions you looked at, where they from the Service Manual or another source?
one from the service manual at XDA-WiKi page and other post from http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond
but both goes up to the same stage and stop.
Yeh I've got the same service manual and it doesn't really go into any detail about how to replace the digitizer. Maybe there's another 'level' of the Service Manual for that. Only question is, where does one obtain it? Good luck replacing it - how come you're replacing it btw? Your touch screen not responding?
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
kortez said:
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
Click to expand...
Click to collapse
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Scratched screen
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
dalewinterstein said:
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
Click to expand...
Click to collapse
digitizer arround 29 USD + shipping.
not sure if LCD is available yet.
if you scratched the screen you will only need to replace the digitizer which is the actual screen you press on.
the only thing is no clear instruction how to replace it!
ammar said:
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Click to expand...
Click to collapse
Without disassembling - no, for sure.
And seeing the video - I would not suggest you to, it's quite hard, cuz it's all packed very tight.
I heard that there's glass in front of screen on diamond that sends the pressures to the real touch screen. But that maybe not true. I guess you'll have to disassemble the diamond to see what the touchscreen is on it.
Or you shoudl find the video, where you can clearly see if the touch diamond' screen have any protective glass..
Kortez,
thanks for your help, do you have link to the said video?
thanks
can't remember where I've seen. But it exists.
http://www.youtube.com/watch?v=_jY46M_NGz0
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
tape said:
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
Click to expand...
Click to collapse
We need the instruction on the replacement step, not the part.
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Adam86 said:
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Click to expand...
Click to collapse
I thought the digitizer cable can be just slot into the connector type, no? Did your digitizer come with soft ply tools? which to help on plying out the screen and digitizer i heard. I'm gathering info before placing my purchase on the digitizer... Coz its badly scratches, felt and kicked!
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Hi, could anyone of you make some pictures or a small video about how to get the display out of the body, or where exactly i need to pull the display out.
i have already dismantled my diamond, but still didnt get the display and digitizer out. When i pulled the display i think i broke it somehow, because now my display shows me only stripes...
anyway, my ordered display still didnt arrive....
if you could make a vid or some pictures, it would be very helpful.
Adam86 said:
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Click to expand...
Click to collapse
how was the soldering part? difficult? as i heard it might melt the plastic cable, no?
If i do cracked the existing digitizer, no harm i see since its already borken though.
Well, i managed to get the lcd and tocuh sceen apart, and now am stuck with the soldering part either.
the sceen has to be pushed out from the inside....the glue they used is pretty strong. and the display breaks pretty fast....
isnt there a way to connect the lcd and ts without soldering?

Damaged Digitizer or LCD Screen? Help please :(

Hi,
Last night I knocked a small table and my girlfriends phone and a remote for the TV fell off.
We noticed that her phone now has a ring of black dots on the screen, mostly visible with a white background (E.G websites) but also from the home screen and the like.
We think she's cancelled her phone insurance, as she's never had a payment out to the company.
Can anyone tell me if its a Digitizer (What is one of these? Is it just the touch screen sensitive part of the phone?) Or the actual LCD Screen itself?
If you click on the photo it will load a larger image
Thanks for any assistance, kinda annoyed about this and wondering if I can repair myself with the parts on ebay. Or does anyone know how much HTC Charge to repair similar? Either in $USD, £GBP or €Eur, I can convert and get a ball park figure.
Hi
First of all is the phone still in warranty? If so take it back to an HTC dealer they should repair it for you for free. TD2 screens are not very good and it's a common fault. ( i had to have mine repaired after just only 3 weeks! )
The TD2 screen is made out of 2 parts, The touch screen or the 'digitizer' as you call it and a normal LCD screen underneath. You need to establish which has gone faulty.
If the touch screen still operates normally i.e the screen does not lock up or freeze and allows you to navigate normally then its the lcd screen below. If the touch screen is faulty one good way of checking is to put a piece of tape over the damaged area and try to lift it up a little to see if the marks / dots disappear and functionality can temporarily be restored.
Its hard to tell from your picture which it is..... sorry
I'm not sure how much a replacement by a dealer would cost, but i'm sure you can replace either yourself. ebay is a good place to look
Hope this helps.
I've had a reply from HTC UK who said the following:
That looks like there are a bunch of very small cracks in the screen. the black stuff is likely the Liquid Crystal from inside the display that has leaked out. If the dots get larger then it would definitely seem that the screen has got some cracks in it.
if this is the case, the standard charge for replacing the LCD is around £180 as sadly it is all one complete unit on the diamond 2, so it is not just the LCD underneath that needs to be replaced, but the whole screen assembly including the touchscreen layer and the actual LCD.
I hope this information helps you to make up your mind.
best regards,
Pete W
HTC
Click to expand...
Click to collapse
Reply was fast, I think <1hr from my first email!
I'll see if I can find any HTC Dealer who will send it off on my behalf, but may just end up buying this: http://cgi.ebay.co.uk/LCD-Screen-Di...UK_Mobiles_Accessories_RL?hash=item588362a12d
Hi mate,
had the same problem...
the item you psetd from ebay is not the one you need to change.
you need a digitizer, not an lcd screen.
i got one from ebay (http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItemVersion&item=290376721935&view=all&tid=393718237019), it includes both the lcd and the digitizer, you can check ebay to find other auctions offering the digitizer only.
you can change the digitizer on your own if you don't mind loosing the waranty of your phone.
cheers
Hi,
I had already found this: http://cgi.ebay.co.uk/Touch-Screen-...UK_Mobiles_Accessories_RL?hash=item5882e7ef74
Will buy in a bit, funds are a bit short today.
The Touch Screen's functionality hasn't changed at all though, no sticking buttons or anything. So I suspect that its the LCD Screen thats damaged but will follow you're advise as you're going to have more experiance than me (and its the cheaper part to begin with!)
Scrap the above post.. my g/f has just told me that the dots on her phone are bigger/worse. Looks like its the LCD Screen afterall
i still believe it is not the LCD.
the digitizer is actually sitted on a glass, and the LCD is below that. it is very difficult to harm the LCD. i also though it was the LCD (at least i wasn't sure which was broken) so i ordered both of them.
if you disasseble the phone you will be sure if it is the LCD or not.
i vote for the digitizer
good luck, if you need any help, i'll be pleased to help you..
Just to update, A few days after I posted and got helpful advice on here.. she called me up to say the dots have disappeared, and they have still gone now a few days after.
She said she put it in the office where she works, under a printer paper tray, and the office was warm. Something has (maybe only temporarily) fixed it.
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Well F**K me! just bought a second hand diamond 2 to replace my xperia...
...seemed to work great checking it out... went home with the phone in my pocket... and as soon as I turn it on the touch screen doesn't work
dissected the whole phone only to discover the digitizer is glued to the bezel!
I ordered this from Ebay, will update if I got it working with the brand new housing + digitizer: http://cgi.ebay.it/ws/eBayISAPI.dll?ViewItem&item=380166349182&ssPageName=STRK:MEWNX:IT
fingeres crossed
Please report back here on this thread if it works
fluke said:
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Click to expand...
Click to collapse
Can any one help with this matter?
fluke said:
Can any one help with this matter?
Click to expand...
Click to collapse
If you can make some photos of the digitizer and the lcd dissasembled maybe, but It seems unlikely to break the lcd when you didn't completely trashed your digitizer.
jodeltje said:
If you can make some photos of the digitizer and the lcd dissasembled maybe, but It seems unlikely to break the lcd when you didn't completely trashed your digitizer.
Click to expand...
Click to collapse
Thanks for the reply as I said previously:
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Click to expand...
Click to collapse
Also the LCD didn´t had any marks at all, but i´m going to buy the TS+LCD and replaced by parts first the lcd because it´s a lot easier to replace then if the problem persists the TS.
I will post the result later when i get the parts to replace.
Superman_1122 said:
I've had a reply from HTC UK who said the following:
Reply was fast, I think <1hr from my first email!
I'll see if I can find any HTC Dealer who will send it off on my behalf, but may just end up buying this: http://cgi.ebay.co.uk/LCD-Screen-Di...UK_Mobiles_Accessories_RL?hash=item588362a12d
Click to expand...
Click to collapse
Can anyone confirm the above link as being both Lcd and Digitizer? I'm sure it doesn't mention it in the listing but the picture looks like it's showing both connectors.
Most likely only the LCD that's my conclusion if you look at the sellers store.
But to be sure e-mail the seller and ask.
http://stores.shop.ebay.co.uk/Elect...QQ_sidZ195653022?_nkw=diamond+2&submit=Search
Soooooo, as I've already posted here, My digitizer was busted on the phone I just bought... what I didn't tell was that I ordered a digitizer, then checked if I could remove it easily...came to the conclusion that I couldn't... and ordered a digitizer+housing so I could easily fit it on.
the mail brought me the digitizer today, and while knowing a better solution was on it's way I couldn't resist and try if I could make it work.
Turns out it super easy to seperate the digitizer from the bezel using a hairdryer (softening the glue) and a knife:
Take your phone apart, just the 4 screws, click the plastic center off it. Remove the digitizer cable, the touchscreen cable and the speaker cable.
now you are able to remove the green plate which holds all chips and stuff.
underneath that is the screen, lift it up gently going under it from the gap the removal of volume buttons leaves, put it away safely.
Now remove the speaker, the buttons under the zoom bar, and the power button(don't forget the the power button, and rubbery thingy that falls out of the bottom, the hole needs to be at the bottom when putting it back in).
your phone should be completely empty by now... just the front and the digitize glued together.
make the front of the phone reaaaaaaaaaallllly hot, put the knive between the metal and the digitizer (I started at the part where the zoombar is) and gently push it between the two parts... (from the inside of the phone to the oudside). Now just keep the whole thing above the dryer to keep it warm and slowly slice your way around the phone (no secret wires are there that you can cut through).
I used some random glue I had lying around to glue the front back to the new digitizer... perfect!
so the screen is like new now
ps bought this digitizer: http://cgi.ebay.nl/Touch-Screen-Dig...wItemQQptZPDA_Accessories?hash=item45eed6effc
Thanks for that jodeltje.
It sounds exactly the same as when i replaced the digitizer on an Omnia. Really not as hard as one might imagine. Taking your time and being careful are the most important things.
Hey guys,
I came into same boat last night.
Dropped my T-Mobile MDA Compact V from 2.5ft table, Backwards (Not towards LCD) and now it has black dots on screen. I guess the LCD has pressed backwards by chip sets.
Here is a screenshot.
I think its LCD damaged but I don't have cash to replace nor device warranty.
Do you think the problem solves eventually? Coz once I had dropped sony mobile and it too had same issue but solved after many days.
Hopefully it solves.
BTW; does LCD affixed to Digitizer? by seeing service manual, it doesn't look like it is. And I afraid to get cheap hongkong LCD screens for about 30$ since they won't be true quality display. i.e blueish.
Thanks...
Best Regards
hello CRACING,
sorry about what happened to you...
from the picture i can say that you have a problem with the digitizer...
your LCD is ok.
i tend to have this problem over and over again the last 1,5 years... i replace the digitizer (or the glass on which the digitizer is attached to) every 3-4 months..
yes the ones you get from ebay are not that good quiality, but well it keeps the phone working...
if you need assistance on replacing the digitizer, i can help you, by providing pictures and istructions...
cheers

[URGENTLY] How to replace digitizer on lcd

hi, i have my phone opened, and i dont know how to replace digitizer on my LCD screen which i take from phone
Please Urgently.. Thx. Mike
P.S. Must i open LCD scr.?
I'd advise replacing the whole screen as digitizer is glued to screen, there is guides to how to replace the screen which can be found via search one of them is very easy as just remove the four screws from behind the screen.
Good luck
If your only replacing the digitizer, which isn't easy I have done a few.
You will need to carefully remove old digitizer, I heat up the digitizer where it's glued and remove it, it will come off in pieces (glass).
then clean residue glue off lcd frame.
then glue the new digitzer.
last part is soldering the connector on the digitzer to the connector on the lcd it's not easy, it can be done with solder iron but I use a rework station makes it 100 times easier.
good luck
now it isnt urgently.. on night i closed phone.. but it is strange.. my slide effect is strange.. whn i put phone on table, so UP part (LCD,action buttons) is little moved right than DOWN part.. for ex. i think this slide after closing has opposite direction !BUT ONLY LITTLE (1mm)!
thanks for advice..
and i think this thread can could be good tread for everyone who dont know what to do with LCD. As me
I would also advise to replace the entire screen. They are easily sourced from a well known auction site and most will supply the opening tools and a screen protector.
A simple web search will find the service manual to open your pda. There are tuts for replacing the screen by removing the 4 screws behind the screen and pulling the housing apart to slide the screen out. Bewarned that if you are too forceful you will damage the mic and other parts that are still screwed to the board.
I bought two Xda stellars some time back. Both needed a lil TLC. One a scratched screen the other the housing was badly scuffed. Having repaired a few PDAs, I thought I would ask an independant store to see what they would charge (labour only as i would supply parts). He quoted £20 for each phone, have a look at the service manual see the steps to take it apart and reassemble ask yourself for the sake of £20 is it worth the aggro.
Good luck with your replacement, I hope this helps and any others who encounter similar issues.
is it possible to use a raphael lcd replacement and install it on the kaiser? thus allowing a higher dpi?
seedub said:
is it possible to use a raphael lcd replacement and install it on the kaiser? thus allowing a higher dpi?
Click to expand...
Click to collapse
Simple answer, No !
ok, on kaiser i can use only kaiser LCD? (no vogue,no tytn 1.....)
Correct, the Kaiser motherboard is ONLY compatible with the type of screen it originally came with.
I heard the t-mobile wing digitizer would work on the tilt.
I have not try it, maybe on next one needs new digitizer.
My son has just broke the screen on his tytn2, reading through there seems to be the screen itself and the digitiser behind, if I order both of these, are they a simple fit, someone referred to soldering, I do not want to go down that route................
Just found how to video on you tube, looks fiddly, but I will give it a go.

[Q] Display Glass and Touch Screen

Well the problem is that, I wanted to fix my HTC HD2 on my own, the glass broke, a day or two ago, so I started to carefully get it out, and when I got it out i realized i broke the flat connection thingy to the touch, therfore I wanted to hear if this was the right thing to buy, I took out the glass, and the black'ish plastic right behind the glass, so is this the right thing to buy or not?
mytrendyphone . com/shop/htc-hd2-display-22940p.html if it is not the right thing to buy, then please tell me what is the right thing to buy, I live in denmark, so a place the is shippin to denmark would be nizzle
Hi!
I'll try to help in case you havn't found a solution yet
I recently had a similar problem. I also broke my digitizer (touch screen, which sits ontop of the actual LCD) and needed a repalcement.
If i understood your post correctly then you broke the flex cable (i think it was flex) which connected the digitizer to the actual LCD. If so, then yes, your link is correct, however, the digitizer cable is SOLDERED to the LCD end (at least for the Europe models, i heard there was a "clip in" version for US models), therefore, if you aren't an experienced solderer (which i wasn't) or you don't know anyone who is extreamly good at it i recommend you buy a full set (LCD + digitizer). Search eBay for "LCD Display Screen + Digitizer for HTC HD2 HD II 2 Leo"
I ordered the same one & installed it, however, be careful when (dis)assembling the phone, especially when installing the LCD connector to the motherboard, i got it wrong the 1st time which resulted in the colors not to display correctly.
Hope this helps

broken screen replacement help ?

hey guys
so last week something unbelievable happened to me and i say unbelievable because no one will believe what happened but thats it what can i do about it xD OK so last week my G Watch fell from my hand while wearing it and it fell off on my Xperia Z from about 20 centimeters and i didn't care that exact moment because i said like WTF it wont harm the device and after 2 minutes i opened my phone aaand its just not working the screen was broken from the area on the left of the microphone and the phone wont work but from a special small area anyways i went to my local Sony agent and he told me that the digitizer cant be replaced alone and that they will be replacing the whole LCD Display so i went to some other 3rd party repair-shops and they said the same thing and they will be replacing it with a non-original Display that cost 1/5 the price of the one that the Sony Agent offered me ( Sony Agent told me that it costs 170 Jordanian Dinars which equals 240 USD and the phone itself new unlocked costs pretty much less than that in my country ( Jordan ) )
Anyways i was wondering guys if i can replace the digitizer alone by myself (by ordering it from eBay or so and disassembling the phone and replacing it at home ) or should i replace the whole LCD Display ?
(Sorry if i had any English mistakes but i"m not a native English tongue )
Best Regards,,,
I had broken touch screen and i watched video on YouTube how to repair just touch screen, ordered just touch screen from Ali and I broke the digitalizer so i ordered whole screen with mask after. My point is, if you don't have tools and skills (or is you first time) buy whole (touch screen + digitalizer) and replace them.
Good Luck!
Sent from my XPERIA M2 using Tapatalk
Dzepar said:
I had broken touch screen and i watched video on YouTube how to repair just touch screen, ordered just touch screen from Ali and I broke the digitalizer so i ordered whole screen with mask after. My point is, if you don't have tools and skills (or is you first time) buy whole (touch screen + digitalizer) and replace them.
Good Luck!
Sent from my XPERIA M2 using Tapatalk
Click to expand...
Click to collapse
thanks bro :good:
Digitizer and touch screen are glued together making it impossible to remove the touch screen without breaking the digitizer that is made of thin glass.
I replaced the combo on my first Z after my car key fell off from above 15cm or so onto the screen, same story as yours! (X_X)
But:
1/ Besides the combo touch + digitizer piece you also have to buy the sticker as the actual glue around the frame will get destroyed while removing the screen.
2/ If your phone is old, you might want to buy an original battery to replace your existing battery.
3/ While reassembling the battery in the phone make sure it does not stick out from the plane surface otherwise it will push on the glue and reopen your phone. Mine had a piece of plastic on its side with harpoon like features; it looked like it had been forced into place with harpoons retaining it: crappy design, to my opinion.
Some 3M strong and thin double side tape might also be useful to keep the battery into place especially if you keep the original one which might unfortunately get a little bent while un-glueing it from the case...
In any case, you should consider its waterproof feature gone!
Good luck!
MRDK_XZ said:
hey guys
so last week something unbelievable happened to me and i say unbelievable because no one will believe what happened but thats it what can i do about it xD OK so last week my G Watch fell from my hand while wearing it and it fell off on my Xperia Z from about 20 centimeters and i didn't care that exact moment because i said like WTF it wont harm the device and after 2 minutes i opened my phone aaand its just not working the screen was broken from the area on the left of the microphone and the phone wont work but from a special small area anyways i went to my local Sony agent and he told me that the digitizer cant be replaced alone and that they will be replacing the whole LCD Display so i went to some other 3rd party repair-shops and they said the same thing and they will be replacing it with a non-original Display that cost 1/5 the price of the one that the Sony Agent offered me ( Sony Agent told me that it costs 170 Jordanian Dinars which equals 240 USD and the phone itself new unlocked costs pretty much less than that in my country ( Jordan ) )
Anyways i was wondering guys if i can replace the digitizer alone by myself (by ordering it from eBay or so and disassembling the phone and replacing it at home ) or should i replace the whole LCD Display ?
(Sorry if i had any English mistakes but i"m not a native English tongue )
Best Regards,,,
Click to expand...
Click to collapse
Just dont go for non orignal diplay you will regret it, most probably they will order a whole new CHEAP QUALITY front panel from ebay which will have poor quality of screen and all the ports. Also the power button will become a bit hard to press.
I did the same mistake and gave my phone to a local phone repair shop which was cheap but my phone went dead the very next day after it came back from repair. I agree Sony Service Centre will charge more but your phone will be in best possible condition.
My suggestion go to Sony people for repair.....
Hope it helps you
Thank you guys very much i really appreciate your help and i think i'm going to the Sony agent because i dont have that much of experience to disassemble the phone and i might get it even worst instead of fixing it :\
again thank you really much guys
Just pay attention to pay a fake screen no original one there's a few different things between the original one

Categories

Resources