Related
I know, its not truly bricked. But as of right now it'll only power up if connected to USB power source and will only boot as far as landscape Android text with a blinking underscore. Part of why I didn't get it fixed last night was my unwillingness to leave and aquire a larger micro SD card. I'll be leaving work in a couple hours to go get some stuff to get this thing working again (its 2 days old) heres the recovery plan:
Aquire 4GB + MSD card
Flash a stock 1.1 ROM (the one thats pre-rooted here)
Install (sideload) that stock joint
Read that Elephant book that comes with the Nook because its working again
From there I'm a little confused. Can I flash Clockwork to a MSD and then use that to flash CM7? Or am I oversimplifying here?
From my trial and error the only thing I have gotten to "un-brick" is to boot into monsters pack then switch cards (i used the 128mb version and it removed the rest of the space on my 2gig card) then format cache and system in the mount section of clockwork. then head to install zip and installed a complete restore to 1.0.1. when thats done I head to BN site and got the side load to 1.1.whatever and let it do its thing. From there your up to date and just like new and can then try and "re-brick" it. Ive had mine for less than a week and done this a few times now cause I am never satisfied.........
The nook is never bricked unless it has a hardware failure. One of the great things about the nook is that it has a very early hook in the boot sequence that checks for presence of a bootable SD card. Creating a bootable SD card is easy. Follow the thread which instructs how to make a CWM bootable SD card. You need to choose between the EXT3 or EXT4 version depending on which ROM you will flash. CM7 requires EXT4 version of CWM. If you try to use the wrong CWM version you will get the outcome that you just observed, stuck at android text. If you want to flash the stock 1.1 rom, then you'll need the CWM EXT3 version.
I had the exact same issue. I used this:
The internal CWR workaround is ugly to say the least. So if you NC should refuse to boot or bootloops, which I hope won't, flash this boot repair that I'm adding just in case. Just flash it, no need for formatting.. Use a bootable CWR SD Card.
HCext4-boot-repair flashable zip: http://www.multiupload.com/LN64D4RXEY
6.8 MB
cf963da4043d91d7f4bf8f784cd02d95 HCext4-boot-repair.zip
from the HC v4 on eMMC thread and it solved the issue and I have since flashed just about everything available with success, including dual boot ROMs. I am using a 1gb card.
Calla969 said:
I had the exact same issue. I used this:
The internal CWR workaround is ugly to say the least. So if you NC should refuse to boot or bootloops, which I hope won't, flash this boot repair that I'm adding just in case. Just flash it, no need for formatting.. Use a bootable CWR SD Card.
HCext4-boot-repair flashable zip: http://www.multiupload.com/LN64D4RXEY
6.8 MB
cf963da4043d91d7f4bf8f784cd02d95 HCext4-boot-repair.zip
from the HC v4 on eMMC thread and it solved the issue and I have since flashed just about everything available with success, including dual boot ROMs. I am using a 1gb card.
Click to expand...
Click to collapse
I'll try this and see if I can get it booted. Thanks.
nswenson said:
The nook is never bricked unless it has a hardware failure. One of the great things about the nook is that it has a very early hook in the boot sequence that checks for presence of a bootable SD card. Creating a bootable SD card is easy. Follow the thread which instructs how to make a CWM bootable SD card. You need to choose between the EXT3 or EXT4 version depending on which ROM you will flash. CM7 requires EXT4 version of CWM. If you try to use the wrong CWM version you will get the outcome that you just observed, stuck at android text. If you want to flash the stock 1.1 rom, then you'll need the CWM EXT3 version.
Click to expand...
Click to collapse
That makes things much clearer for me. I knew CM7 required EXT4, but was unaware that the CWM flashed MSD would be properly formatted and couldent be bothered to boot in Linux to do it. Blame lack of sleep. Thanks!
How do you access clockwork recovery on the nook? Does the 3 button combo work? Is it different if you are running a rom off of the sd than if it's run directly off of the nook?
You have two options:
If you're booted up you can go to the Rom Manage app and select Reboot In Recovery Mode.
Or you can shut down by pressing power button and then on screen shut down button.
When your NC is completely off press and hold Power and 'n' button simultaneously for about 5 seconds.
It took me two hours of searching to find this answer. Hopefully this thread will come up in search results
Thank you, I was wondering this also.
neither method seems to work for me unfortunately. Both just end up booting normally.
Are you sure you installed CWM? From RomManager you need to select "Flash ClockworkMod Recovery". Also, I'm not sure how having an active system on an SD card will affect this process. Are you booting from eMMC or SD?
I don't mean to thread steal (hopefully i am just providing more useful information if my question/problem is answered).
When I boot into clockwork, i get can't mount SD card. Therefore can't install any themes as the themes are on the SD card, is there something I am doing wrong? I think I reformatted my SD card to be fat32 and not NTFS, does this matter? It seems to be able to read off the SD card when I am fully booted up.
TIA
easyski said:
I don't mean to thread steal (hopefully i am just providing more useful information if my question/problem is answered).
When I boot into clockwork, i get can't mount SD card. Therefore can't install any themes as the themes are on the SD card, is there something I am doing wrong? I think I reformatted my SD card to be fat32 and not NTFS, does this matter? It seems to be able to read off the SD card when I am fully booted up.
TIA
Click to expand...
Click to collapse
Different problem. Reformat in NTFS and try again.
k2snowboards88 said:
neither method seems to work for me unfortunately. Both just end up booting normally.
Click to expand...
Click to collapse
I was having the same issue after flashing the eMMC install for Honeycomb from the dev forums. I ended up going back to CM7 but when I tried to install the new Clockwork Recovery (3.0.1.0) using the manual method it wouldn't work and just kept booting strait to CM7.
To fix it I first restored the stock boot img from this thread.
http://forum.xda-developers.com/showthread.php?t=919353
After that I put in my bootable SD card and flashed the cwmr_3.0.1.0.zip from this thread.
http://forum.xda-developers.com/showthread.php?t=971197
That fixed my boot issues and got recovery working, after that I could flash the image I wanted using a non-SD recovery.
Before doing any of that it would probably be a good idea to toss in a bootable SD card and doing a backup.
So I finally took the plunge and picked up the Nook color, bought it second hand with HC already on the eMMC so I am not sure exactly how anything was done before. I have been reading the guides and while not completely lost, there's just some things I am unclear of right now.
I installed Rom Manager to install CWR, after installing and flashing it I cant access Recovery, but wasnt sure if it ever worked. Was this the wrong way to go about getting CWR on the unit? I am trying now to boot into a default CWR SD card and run a fix from this thread hoping thats the issue
http://forum.xda-developers.com/showthread.php?p=11591197
I dont really have a need for the Stock config so putting everything on eMMC for me sounds ideal and am currently trying to get the dual boot config from here running.
http://forum.xda-developers.com/showthread.php?t=959461
Question now is if I get CWR running from the sd card, can i just apply the prep file and load the pre configured installations from that page? Does the dual boot both boot from eMMC? Will I need to format my existing solution to install that setup?
Thanks for any feedback.
s0n- said:
So I finally took the plunge and picked up the Nook color, bought it second hand with HC already on the eMMC so I am not sure exactly how anything was done before. I have been reading the guides and while not completely lost, there's just some things I am unclear of right now.
I installed Rom Manager to install CWR, after installing and flashing it I cant access Recovery, but wasnt sure if it ever worked. Was this the wrong way to go about getting CWR on the unit? I am trying now to boot into a default CWR SD card and run a fix from this thread hoping thats the issue
http://forum.xda-developers.com/showthread.php?p=11591197
I dont really have a need for the Stock config so putting everything on eMMC for me sounds ideal and am currently trying to get the dual boot config from here running.
http://forum.xda-developers.com/showthread.php?t=959461
Question now is if I get CWR running from the sd card, can i just apply the prep file and load the pre configured installations from that page? Does the dual boot both boot from eMMC? Will I need to format my existing solution to install that setup?
Thanks for any feedback.
Click to expand...
Click to collapse
HC, as far as I know, is the only rom that does not respond well to cwr installed internally (I have had those issues). If you get an sd image of cwr burned, you can add any flashable rom to that same card and flash it in recovery (install zip from sd card). If you want to play with CM7, do a backup of your HC rom from your sd card, do your formats and flash the gb rom. I think in theory, if you wanted cwr installed internally, you can load a cwr zip on your cwr card and flash it. I have not tried to dual boot anything, so can not offer any feedback.
bdcrim said:
HC, as far as I know, is the only rom that does not respond well to cwr installed internally (I have had those issues). If you get an sd image of cwr burned, you can add any flashable rom to that same card and flash it in recovery (install zip from sd card). If you want to play with CM7, do a backup of your HC rom from your sd card, do your formats and flash the gb rom. I think in theory, if you wanted cwr installed internally, you can load a cwr zip on your cwr card and flash it. I have not tried to dual boot anything, so can not offer any feedback.
Click to expand...
Click to collapse
So I ran the fix permissions and now I can boot into Recovery From Clockwork or boot from the SD card. There are a couple problems, in order to install the dual boot I need to run recovery from the eMMC but that doesnt seem to mount my SD card or I need to adb into the recovery so I can permission something to run, however doesnt seem to have adb running in Recovery and I dont see an option to restart it.
Alright so everything is working, had to format the SD card. Guess CWR SD sets it up as a boot partition so it wasnt mounting, dual booting froyo + HC, just have to figure out the OC kernels now for each.
I've already got my SD card ready to root my nook, and the files are ready to install hc v4 2nd...i can't wait this should hold me over until the 10"ers come down in price
So I'm booting from a SD card into CM7 7.0.2 currently. I'm using a custom boot file so I can choose to hold down the home screen button if I want to boot into the stock 1.2 OS instead.
I only have this single 2gb SD card to use atm. What would be the proper process to update to the nightly 69 build from here? I need to make sure that when I update, my current SD card is in there and that's where the install is saved to. I had an issue prior where I booted with an alternate SD card (which I no longer have) and it installed to the eMMC. That wasn't fun as I had to do a complete restore.
Thanks!
I am booting from an SD card.
To update, I put the uSD card in the PC and then just copy the new build zip file to the uSD card.
Then I put the card in the Nook, press the N + power button and when I see the "Touch the Future of Reading", count to 4 and release the buttons. Don't count to slow. I noticed one time the TTFOR disappeared and it booted into the Nook software. I just shut it down and did it again.
The Nook will automatically see the new zip file, expand it and load the new build. Once done, it will delete the zip file from the uSD card.
I noticed the newer builds automatically reboot the unit but if yours doesn't, it will stop at "Flushing Cache" and sit there. Leave it alone until the screen goes dark (a couple of minutes) and then reboot it (N + power button). You should get the Android. and about a minute later the CM7 spinning logo.
You are updated. And you don't lose any apps or data either!
If you are overclocking, I would set it back to 800MHz before you do this as a precaution.
Finally, there is an easy way to add overclocking to a new build. You just need the overclock zip file, the new build and WinRAR 3.80. Let me know if you want that info.
Well that worked as you said, thanks! I did have one problem but I fixed it myself. As I mentioned, I have a modified boot file which loads the Nook OS if I hold the N button. So trying to get into recovery or have the CM7 noticed the .zip file by holding Power+N didn't work. Luckily I still had the original u-boot.bin file and was able to copy it back onto the SD card and then I was able to get the update installed.
As to the OC, I assume I'd just put it back on the same way I did with the original.
I've read your post, and a few others but I'm either not understanding (my money is on this one!!!!) or missing a step.
I'm running Nook Color Stock 1.2 on emmc and CM 7 on the SD card.
I've tried using ROM Manager as well as copying the latest nightly to the /boot partition of the SD card.
If I boot into recovery and update the zip from the SD, I always end up over-writing the emmc of the nook, losing stock and all my apps, instead of the CD card being updated.
What am I doing wrong?? Would like to upgrade to the latest nightly. But I don't want to screw up stock (hate having to restore and redownload all the apps every time).
Thanks
No matter what I do, I always end up over-writing the emmc instead of updated the SD card.
phoenix1972 said:
I've read your post, and a few others but I'm either not understanding (my money is on this one!!!!) or missing a step.
I'm running Nook Color Stock 1.2 on emmc and CM 7 on the SD card.
I've tried using ROM Manager as well as copying the latest nightly to the /boot partition of the SD card.
If I boot into recovery and update the zip from the SD, I always end up over-writing the emmc of the nook, losing stock and all my apps, instead of the CD card being updated.
What am I doing wrong?? Would like to upgrade to the latest nightly. But I don't want to screw up stock (hate having to restore and redownload all the apps every time).
Thanks
No matter what I do, I always end up over-writing the emmc instead of updated the SD card.
Click to expand...
Click to collapse
All you have to do is put the update zip on the boot part' of the sd card and boot up the sd install like normal and it'll see the zip and automatically flash it for you.
I've tried using ROM Manager as well as copying the latest nightly to the /boot partition of the SD card.
Click to expand...
Click to collapse
If you're booting CM7 off uSD, you can forget about the "ROM Manager".
phoenix1972 said:
I've read your post, and a few others but I'm either not understanding (my money is on this one!!!!) or missing a step.
I'm running Nook Color Stock 1.2 on emmc and CM 7 on the SD card.
I've tried using ROM Manager as well as copying the latest nightly to the /boot partition of the SD card.
If I boot into recovery and update the zip from the SD, I always end up over-writing the emmc of the nook, losing stock and all my apps, instead of the CD card being updated.
What am I doing wrong?? Would like to upgrade to the latest nightly. But I don't want to screw up stock (hate having to restore and redownload all the apps every time).
Thanks
No matter what I do, I always end up over-writing the emmc instead of updated the SD card.
Click to expand...
Click to collapse
You are probably using the install zip option. You do not do this. You just put the zip on the boot partition, boot into recovery and the reboot. DO NOT flash anything.
Sent from my LG Optimus V using Tapatalk
Let me try to clarify... when they are saying boot into recovery... they aren NOT meaning Clockwork Recovery... they mean using the boot menu (press "n" button when you see the Cyaonogen logo) and selectin boot from SD card and Recovery. That is the SASD rocovery (install) mode and will install the update zip file from the root of the boot partition.
Thanks for clarifying DizzyDen!!! That's the part that I was screwing up
Like I just screwed up the Stock again...but that's alright...live and learn
Updating the latest right now...then I'll be putting stock back on emmc
Thanks again for the clarification
Updating to the latest nightly on CM7 SD installation?
I'm a newbie so please have some patience. I'm trying to do the same thing, update my cm_encore_full-159.zip to cm_encore_full-177.zip. I boot from a microsd card to Android. When I install it I pushed a button during the early boot process and went to a menu. Changed "boot device" from "emmc" to "SD" and "Normal" to "Alternative". When I turn on the Nook Color after it installs, I do nothing and it boots to Android but if I put a button it goes to the menu where I push the volume down button 3 times and I boot to the stock Nook Color. So, if I copy the cm_encore_full-177.zip to my microsd card, go to the menu, change the "emmc" to "SD" and "Normal" to "Alternative, this should update my 159 to 177 without losing any apps, email, etc.? Thanks
themofoman said:
I'm a newbie so please have some patience. I'm trying to do the same thing, update my cm_encore_full-159.zip to cm_encore_full-177.zip. I boot from a microsd card to Android. When I install it I pushed a button during the early boot process and went to a menu. Changed "boot device" from "emmc" to "SD" and "Normal" to "Alternative". When I turn on the Nook Color after it installs, I do nothing and it boots to Android but if I put a button it goes to the menu where I push the volume down button 3 times and I boot to the stock Nook Color. So, if I copy the cm_encore_full-177.zip to my microsd card, go to the menu, change the "emmc" to "SD" and "Normal" to "Alternative, this should update my 159 to 177 without losing any apps, email, etc.? Thanks
Click to expand...
Click to collapse
1. in bold text above... select "Recovery" not Alternative...
2. you either move the SD to your computer to put the update on the boot partition of the SD or you have to mount /dev/block/mmcblk1p1 to a directory (I created /sdcard/boot for this) and push the update to the BOOT partition.
Nook Color How to Update to CM7 Nighthly
Good Day,
What a fantastic website! I am new to the forum. Could you please answer the questions or provide a link to the answers?
1. What utility and procedure would I follow to back up the stock Nook Color partitions in ROM to include the stock Nook Color apps I have installed?
2. What utility and procedure would I follow to back up the apps I have purchased from the Android Market place for CM7 running off the SD card?
3. I have update-cm-7.0.0-encore-signed.zip installed. I want to update to cm_encore_full-177.zip. Do I use win32image to "burn" the new nightly to the SD card? Or, do I drag and drop the new
nightly to the SD card? If yes, on which directory (folder) on the SD card do I place the new nightly build?
Thank you!
atl10spro
Try my best to help.
1. I don't deal with stock, so can't help here.
2. I never intend to run any backup when booting off uSD, can't help.
3. Assuming you're booting off uSD, then just copy the new .zip file (do not rename, do not unzip) into the boot partition (root folder) of the card. Insert it into the NC, boot it into Recovery. When it's in recovery mode, it'll fully automatically do the update then deletes the .zip file, you don't have to do anything, just wait until it shuts itself down then you power it up.
I am running the following - CM7 - nightly build 08022011 on SD - Dalingrin's OC kernel 2.6.32.9 @ 1200MHz NOOKcolor
I am trying to update to a newer nightly build. I have the file downloaded on the SD card but can't get it to update.
Where does the file have to go?
I tried to reboot into recovery mode and that didn't do anything.
Any help would be great.
***I must have been sleepy yesterday as I got it to work now....
removed ./10chars
Hi!
I have a problem a Nook of a friend which is stuck on Read Forever screen
I had install the rom of CM on it. and after I went to rom manager to make an update of the recovery i tried to reboot the device.
after of that the nook is stuck in this screen,
I tried to make a bootable SD recovery card but it does not boot from the SD either.
Any solution.
Is CM7 installed on the card or the internal memory?
sorry guys I had made a bad copy of my sd card recovey.
everything is ok now.
please Mods delete my thread if possible!
Thanks in advance!
merry x-mas guys
Got a problem,
Step-son got a nook color from his grams, intended to put CM7 on it so he has some halfway decent tablet, so he can play his flash games on it.
- after setup of the Nook color, it downloaded version 1.4.1 of it's own B&N OS
- did the uNooter from an 8 GB SD card (according to these instructions http://wiki.cyanogen...ll_Update_Guide), worked almost like a charm, at reboot i got a popup reading "default action: Home OR [that special menu-loader from the uNooter on the SD card]. after tapping the special menu-loader i was able to go into ROM MANAGER, did FLASH CLOCKWORK MOD RECOVERY, 5 minutes later gave SUPER USER/ROOT permissions, reboot, worked fine.
- tried to put the CM 7.1 on said 8 GB SD card, noticing that the uNooter image only has a ~70 MB partition and the rest of the 8GB is unused, so the 100MB "update.zip" doesn't fit (obviously).
- DOWNLOADING Roms via ROM MANGER directly is obviously a no-go, because it has no premium license, and loading it from the 8GB SD-card isnt working because the partition was only ~70 MB small.
- ASSUMING that the uNooter is NEEDED EVERYTIME to get into that special menu-loader for the Color Nook, I selected in ROM MANGER the option PARTITION SD CARD, thinking it will lead me into a menu where i can make another partition, beside the uNooters, to dump the CM 7.1 update.zip to flash the Nook Color's Rom with CM 7.1
- next thing I know, it reboots, and its stuck at the "Read Forever"-boot screen.
I PRESUME that ROM MANAGER's "partition SD card" screwed with the internal/virtual 'SD-card partition' and not my actual microSD chip loaded into the Nook Color's microSD-slot.
Is there a way to restore the device and/or load CM 7.1 on it, and if so, how; or am i ****ed ?
cheers
@
PS: is there a way to force-reboot the Nook Color? like as it's on phones often the case, by force-crashing it by holding down a combo of keys ? if so, which ones?
Atlana, same question answered here, as well as over on CM forum.
forum.xda-developers.com/showthread.php?p=20677328#post20677328
Hold power button for 20 seconds or so to force power off. Do it twice until you see it start to boot.