actually the touch of my phone (Motorola milestone) stop responding only the left bottom corner
and then sometimes it works on its own .The shop keeper told me that its touch needed to be replaced
and they are not able to find it ..plz help
give me suggestions
waiting
I was able to find a digitizer for my droid on EBay and found a video online showing the installation procedure. Give it try and see if you can find one there.
before buying the digitizer please make sure it isn't:
-bad software flash
-bad flex cable
-static electricity on your hand / clothes
Those may sound stupid but give them a try
thanks you sir for replying.and i have checked my cell by shop thy said its touch...and before flashing its doing problem
can any body send me some link to order 1 piece if digitizer ( touch ) plz let me know
pblm solved //got digitizer through ebay
mod close this thrread plzzzzz
Related
My touch diamond with rom 1.93 suddenly is very dim screen. When i reset & there is nothing on the screen but i can hear the os startup sounds. After a while i will be able to see something on the screen, but it is extremely dim to the put where i cant use the phone outside. An error shows up right away stating that there is a microp version mismatch & to reinstall the microp firmware. Tried reinstalling the 1.93 rom, but that did not help. still the same error. Can anyone help out here, im at a total loss? Thanks Malik
And?
Did you found the solution for this?
Send it warranty if uu don't want it take appart, i had same problem i recon is the screen connection (in my it was lose)....
I opened a tread 4 it here
http://forum.xda-developers.com/showthread.php?t=418828
can u tell me if u find an answer? cuz i got the same prob
@ check this out
http://forum.xda-developers.com/showthread.php?t=657514
Use warranty if you have. Goto a tech guy if possible. If no solution then sit down and get ready to rip it apart.
P.M me, i'll help all i can, cause i'm in the same boat, but in despair. Have no hope left so have boldness to do anything.!
Bulls eye!
microp error
This occurs when while boot diamond fails to find the correct hardware radio, wifi and Bluetooth
Well the small cable was not attached properly so i opened and attached it. Hell of a job, HTC are very compact.
And WIFI bluetoth back on.
Warn you this cable is very delicate and HTC's original manual says to replace this cable once you open your device. But where will you find a cable?!?!
And I have got the screen from ebay U.S.
Now while replacing the screen the tech guy stupid NooB forgot to take off the last fblack colored film of the display and reattached the new one over it, so now the digitizer isnt wrking properly and the new screen appears very dark.
I have to do it my self. I dont know if i will ever have my diamond back again
For display and lower keyboard panel(having buttons and breath)
You have to attach two small connectors. They are very hard to install and yes it would be better you get it done from some place.
Hi,
My friend gave me his broken G1(digitizer+screen).
I've bought new ones and replaced them.
Now i have a weird problem that the lower part of the digitizer is not responding, i cannot open the menu button or touch anything there.
but if i hold my finger for few seconds and then let go then it will open a "quick search".. like it is responding.
is it possible that i've messed something along the way or that the digitizer was not working from the factory?
Also was wondering if there is some program to calibrate?
Thanks
Anyone?
can't help you actually, but i hope this hint helps you:
the g1 has a capacitive touchscreen, it doesnt require a digitizer / calibrating...
but as i don't know how capacitive touchscreens work in detail i can't help you...
I have the same problem :S
I have seen posts about the lower part of the digitizer not working. I think your digitizer is defective. Try wiping and installing your rom again or If you can, see if you can disconnect the ribbon connecting the digitizer to the LCD and then connect it back to the LCD, restart your phone and If it still does not work then your digitizer is probably defective. Contact the seller and ask for a refund or replacement would be the best choice.
Ye I managed to fix it.
I opened and reconnected my phone probably 100 times :S
Oh well, I hope its fixed permanently and Iwon't have to open it again incase it drops out again :S
If you just recently bought the digitizer, i would suggest you ask for a replacement so that problem would not occur again.
theoneonly said:
Ye I managed to fix it.
I opened and reconnected my phone probably 100 times :S
Oh well, I hope its fixed permanently and Iwon't have to open it again incase it drops out again :S
Click to expand...
Click to collapse
did this really work?!?!?!?
Hello,
I have a busted galaxy s (memory card corrupted).. now i can get another one with a broken screen for a cheap price.. my question is, can i just replace the motherboard part where the MC is located, or must i replace the broken screen on the working one.. the screen replacement is a lot harder but i think it wont give me to much trouble.. i am wondering if the motherboard replacement will work without any IMEI or other parts of the phone conflicts.. have never done that before. If someone has, please tell me your experiences.
Both phones waranties are useles and tryed already. They are both unlocked euro phones gt i9000.
Thanks.
G. Lukic
The NAND flash is located on the mainboard which is separate from the screen.
You don't need to touch the display with its electronics - there are some display controllers.
Just change the mainboard and that's all
Thank you i thought so too. i had already put my phone apart 3 times, just to see if by some miracle nand would start working again stupid i know, but i was quite desparate..
hi does anybody know where can i find a mainboard for i9000 i googled with no result. i have my screen been replaced. now there are a few grey horizontal lines on it. the strange thing that they dissapere when i plug charger and when the temperature goes up. and sho
wing back when the phone goes colder. in the lab i was told that the problem is in the connector on the main board. and there is nothing to do with it. so can anybody tell me where to find a replacement? thank you.
I started to have this peculiar problem where my part of my screen ( pic attached ) stopped responding a few days back...rebooted it normally,then in safe mode & then cleared cache etc, still no effect...the phone is 2 years old now & from what i have read till now , it maybe a digitizer problem
Guys plz advice on what can be done other than sending it to the repair shop which i am sure will cost a fortune...any other way to fix this problem?? btw i am running Viper & Elemental latest versions...
drsamratroy said:
I started to have this peculiar problem where my part of my screen ( pic attached ) stopped responding a few days back...rebooted it normally,then in safe mode & then cleared cache etc, still no effect...the phone is 2 years old now & from what i have read till now , it maybe a digitizer problem
Guys plz advice on what can be done other than sending it to the repair shop which i am sure will cost a fortune...any other way to fix this problem?? btw i am running Viper & Elemental latest versions...
Click to expand...
Click to collapse
hi,
i don't think that can be repaired thru software. you need to replace the digitizer on that phone. and unfortunately, the lcd and digitizer is bonded, it's not easy to just replace the digitizer. you can look on ebay the replacement lcd complete with frame and back cover. the only problem you will encounter if you DIY it is the disassembly, you can watch youtube or check ifixit on how to disassemble the phone.
drsamratroy said:
...it maybe a digitizer problem
Click to expand...
Click to collapse
Most likely, but just in case remove the screen protector (if you use one) and test again.
My touch screen is having issues.. In one area about 3/4 down near the bottom across the length the screen is not responsive.. Here is a picture showing where /i62.tinypic.com/2ykn8rd.png (please add the http:/ before the link to check it)
I checked the touch with the service test
Is it a problem with the hardware? Because I haven't dropped it and there aren't any cracks..
Only thing I can think of is that my charger wire is a little frayed and that charge has seeped into the screen.. But is this damage permanent or how can I fix it ?
Any help would be much appreciated.. Thank you
Any help please?
randikag said:
Any help please?
Click to expand...
Click to collapse
Hi there, I'm sorry I couldn't find any information regarding your problem in the web and the way how to fix it. I'm suggesting you to send your phone to specialized repair center (Sony). Or you just can give a try and reflash the rom you're using, maybe it causes this problem - nobody knows until you try.
Good luck! If you're answering or anything like so, please quote the message that I'd be able to see it.
Hi, if the touch screen previously works without problem, can be an hardware damage of the touch screen panel, as you can see there is only one row that don't works, all you have to do is replace the entire LCD+Digitizer assembly, and the phone will works perfectly