[Q] USB doesn't recognize download mode. Stuck after installing speedmod kernel - Captivate Q&A, Help & Troubleshooting

I had rooted my phone previously running 2.1 and yesterday decided to try cm7. (I've flashed many G1 roms but none for Captivate)
Sorry this is quite long but wanted to give as much detail as possible
I was reading and watching the guides. Installed rom manager and flashed ClockworkMod Recovery 2.5.1.0
Rebooted the phone and tried to see if I can get into download mode by holding vol up + down and plugging the USB cable.
Once it booted tried to copy some other roms (zips) to the phone but the USB wasn't working on windows for some reason so rebooted in Linux. Phone mounted at first (for about a minute) but something happen and I lost the mount. I unplugged/plugged the usb cable but wasn't able see the phone as a drive even with fdisk.
So I ftped to the phone:
3buttonFix.zip
captivate-efsbackup.zip
cm7-captivate-initial-20110304.zip
speedmod-kernel-i897-k13c-500hz-CWM.zip
Installed 3buttonFix.zip (should let me enter download mode) from recovery, rebooted but still couldn't get in download mode.
Installed speedmod-kernel-i897-k13c-500hz-CWM.zip from recovery. Not sure if I had to do anything special like reformat the filesystem with the new kernel?
After reboot the phone gets stuck on Galaxy S sgh-i897 screen. Got back in recovery and installed captivate-efsbackup.zip and cm7-captivate-initial-20110304.zip
The cm7-captivate-initial-20110304.zip fails when trying to write the modem
'assert failed: write_raw_image("/tmp/modem.bin", "radio")'
I plugged the phone into another computer at that point and was able to get into "Download mode" for the first time. Odin didn't recognize the phone though. Download mode is very flaky. It starts sometimes, sometimes it doesn't (battery charger starts) even on the same port with the same cable. I have tried installing captivate drivers and/or kies on 7 different systems (5 laptops 2 desktops) but Odin never recognizes the phone and windows trows out a "USB Device Not Recognized" msg
I think my usb is not working properly but the guides how to recover assume working Download mode with Odin. Any suggestions on what to do for that? Or I guess I can download a different rom and/or kernel on my sdcard than mount the sdcard through recovery and install that way?
Any advise is appreciated as I'm not very familiar with the kernel and rom differences for captivate

Well you messed up on the instructions but that is a separate point.
I went through your post quickly so if I am saying something you grave tried I apologize
What drivers are you installing
Have you tried multiple ports
Are you using oem cord
Have you restarted your computer
Have you ever used odin before
CM7

I have used the following drivers:
SGH-i897_Captivate_USB_Drivers_5_02_0_2.zip
SAMSUNG_USB_Driver_for_Mobile_Phones_x86.exe (just the usb modem driver)
2 different versions of samsung kies which include usb drivers (don't have the software versions handy but I can get them if that will help)
Ports:
Multiple computer and multiple ports. Will try few more options
Cables:
Used 3 different usb cables. 1 of them is from a BB phone. 1 of the other 2 is the one which came with the captivate (not 100% sure though)
Reboots:
4 of the 7 computers I tried on were rebooted. One version of kies requires this anyhow.
Odin:
Haven't used Odin at all. I think when the phone gets connected and odin recognizes it one of the top left blocks changes color right ? I tried to flash even when it didn't (just to make sure I wasn't missing something) and saw 0 successful / 0 failed

Do you have android sdk installed on any of the computers?
CM7

So many red flags that something wasn't right with your phone and you still tried to flash it? I just don't get it.

@Miami_Son: Yeah but i'm too thick headed - living dangerously but yeah you're right.
@mcord11758: I have android sdk installed on my linux build at home. I'll put it on a windows system at work and see if it can see the phone. Anything in particular I should do / look out for ?

At least you've got a good attitude.

I think if you have kies installed it conflicts with the samsung drivers odin uses. Try uninstalling them and flash odin.
Sent from my i897
Edit damn swype

1tontomato said:
I think if you have kies installed it conflicts with the samsung drivers odin uses. Try uninstalling them and flash odin.
Sent from my i897
Edit damn swype
Click to expand...
Click to collapse
Try this first
Sdk to install updated drivers if this fails
CM7

I've done almost the exact same thing...having the same issues. Phone would not connect to computer. Other captivates connect fine. The phone is now stuck on a boot screen and I can put it into download mode but Odin or the computer will not detect it at all. I don't think I can get into recovery mode, nor can I get into a rom...pretty much just download mode or a boot screen.

@1tontomato: Tried uninstall kies, reboot, install samsung usb drivers, reboot still don't see the phone connected in odin
@mcord11758 The sdk is trying to download the repository directly and I'm behidn a proxy server at work. I'll update tonight, it will be most likely very late by the time I get home.
@kwhee07 Yeah sux to see a download mode but not being able to download. I can get at least into recovery so I guess I can at least flash something that way. The ports really make difference, I've seen many would just charge the phone and some will get your phone into download mode at least. Try a different pc and cable if you can.

I have the sdk...I've tried about everything else I can find. Is there a possible method of fixing this via the SDK? I feel like if I could make the computer force [odins] data out the usb port, it would work, the phone would be in download mode awaiting data....but I cant get odin to see it

There is a package you can install in sdk for usb drivers. Dl it
Open odin
Get into dl mode
Unknown device pops up
Click on it
choose custom drivers
Navigate to c drive/program files/android/extras/google add ons/usb click ok (the path may be slightly different) the computer should try to install the correct drivers
If it works odin should now recognize your device. If not I got nothing
CM7

Got the USB drivers from the SDK and tried to force them when it sees an unknown device, but I get "The specified location does not contain information about your hardware"
I tried to force it to use the samsung drivers also but without success.
Is it possible to just download a rom or kernel and update my current state? So that the phone at least boots. I can install stuff through recovery. Download mode is nice and everything but I'm giving up on it, don't have any more ideas to try
I have been trying to see data on my sdcard from ClockworkMod Recovery 2.5.1.0 I go to
Mounts and Storage -> mount /mnt/sdcard
Install *.zip from sdcard -> choose zip from sdcard
I don't see /mnt at all I try and go under sd/ but it says No files found.

bestivo said:
I have been trying to see data on my sdcard from ClockworkMod Recovery 2.5.1.0 I go to
Mounts and Storage -> mount /mnt/sdcard
Install *.zip from sdcard -> choose zip from sdcard
I don't see /mnt at all I try and go under sd/ but it says No files found.
Click to expand...
Click to collapse
Under mounts and storage do you see the option for mount usb this might be able to force your computer to see it as a removable drive. If out does you should be able to copy another rom to the sd and flash. This may or may not work for you because you might still need to repartition which you only do with odin. Take this advise with extreme caution I really think you need odin If you do decide to flash another rom, use cognition because Dg's includes the fixed boot.bin. Probably because so many people use the one click and kill their button combos and don't know it. Other devs don't include it in their roms, because it's dangerous to over write something that doesn't need to be overwritten. Good luck
Sent from my Fusion 1.8 SAMSUNG-SGH-I897

I tried already the usb mount option from recovery at home and now at work also on few different systems/ports including a linux machine. I don't see the drive connected.
My only option left is to get somehow the sdcard mounted and install a rom from there. Or maybe just repartitioning/changing the filesystem might fix the getting stuck problem.

I ended up bringing my phone back to att, and they said that the 1010 batch was under product advisory..they exchanged my phone with almost no questions asked.
Now i have a 1008 and am running CM7

Finishing up the story in case it might help somebody in the feature.
I called AT&T to get my phone replaced and it turns out it has liquid dmg. There's a little white sticky that turns red when there's liquid dmg. Mine was pink but wasn't wait so no warranty for me. Turns out most of the time people get liquid dmg is if they leave the phone in the bathroom or close to the kitchen's sink, which is kinda bs but whatever.
I've tried few more times. Tried even on a Mac and on a Linux system (using http://forum.xda-developers.com/showthread.php?t=755265 )
I was about to give up and go seek one of the 'professional rooters' but last thing I tried was to use an 'air duster' and clean the usb port on my phone. After that Odin was able to see my phone. The connection was dropping on/off but it successfully finished a flash.
Not sure if I should even try to put another rom or the official froyo update but at least for now I'm up and running
Thanks all

Related

Help, Bricked and no solution is working

Here is the exact details on what happened in the order I remember them
1. Was using the latest Cognition Rom and decided to try something different
2. Used Odin to flash back to stock
3. Flash Axura CE Version 4
4. Decided I liked Cognition better (Not bashing Axura, great Rom but not for me)
5. Went to try Odin and USB connection was not recognized
6. Knew USB connection worked under Cognition so tried to use Clockwork to restore to it.
7. After restore I got numerous FC and shut down.
8. After shut down phone would not boot but stuck on the i9000 Axura loading screen.
9. Now the problem I have is that I can get to recovery mode with no problem but USB is not recognizing connection, tried to get CW to mount USB so I could put the zip version of stock ROM on it but it will not mount. Also tried uninstalling samsung drivers and reinstalling with no luck
OUT OF OPTIONS
Any Help greatly appreciated
vstarrydr05 said:
Here is the exact details on what happened in the order I remember them
1. Was using the latest Cognition Rom and decided to try something different
2. Used Odin to flash back to stock
3. Flash Axura CE Version 4
4. Decided I liked Cognition better (Not bashing Axura, great Rom but not for me)
5. Went to try Odin and USB connection was not recognized
6. Knew USB connection worked under Cognition so tried to use Clockwork to restore to it.
7. After restore I got numerous FC and shut down.
8. After shut down phone would not boot but stuck on the i9000 Axura loading screen.
9. Now the problem I have is that I can get to recovery mode with no problem but USB is not recognizing connection, tried to get CW to mount USB so I could put the zip version of stock ROM on it but it will not mount. Also tried uninstalling samsung drivers and reinstalling with no luck
OUT OF OPTIONS
Any Help greatly appreciated
Click to expand...
Click to collapse
Is download mode still available? If yes your not screwed but your drivers might be.
What steps do you use to get into download mode.... 3 buttons or usb/vol+- combo ?
Yes download mode is available. I used the holding the volume up and down and plugging in USB. It goes to download mode with no issues whatsoever.
Well then this is a non-issue issue... Possibly a bad flash... Go in download mode again and reflash.
Your a bit crying wolf with no reason here. As long as download mode works and Odin detects the phone you have no issue
Use the Odin-one click if you have to ...but really calling it a brick when you have download mode gee-wiz.
Thats the issue. It is not detecting in ODIN. If it was detected I would have reflashed with no problem. I get the message that the USB device has malfunctioned and is not recognized
Try re-downloading the USB drivers - use the ones found in my signature.
If you can get into recovery - you can then get back into CWM and attempt to re-flash again - but you'd still need to 1-click back to stock using ODIN.
Have you tried to plug the usb cable in the Mb directly or changing its port ?
I actually downloaded your drivers last night and installed them. Still not recognized. I can get to CWR and have the zip files for AXURA and Cognition on the SD card. Get errors on various lines when trying to install either. I have tried 3 different cables and 4 different computers with no luck on recognition
Well crap... I did have the USB issue on my work's XP Machine - but when I went home to my Windows 7 box - it ended up finding the phone fine and I was able to flash back to stock.
Any chance you can find a Windows 7 box?
Dont know anyone with one unfortunately. I need to install Win 7 through bootcamp on my mac. I tried to even get it to mount as storage through CWR on it with no success
Well.. I can say with 99% certainty you should be able to restore the phone.. also if you look at my sig - I just added a link to the OTA_JH7.zip that is CWM flashable if you could somehow get the zip onto your phone that is lol.
Hm.. and I dunno how the virtual box of Win7 will run - but it's worth a shot. Windows 7 seems to be superior when it comes to figuring out devices vs. XP. I was shocked when it found my then toasted phone (similar issue your currently experiencing).
Haha, I have your zip to as a matter of fact. I picked it up but I dont know how to get it put on the phone if it wont recognize usb. If CW usb mounting would have working I was gonna put it on the internal sd and let it flash it
and actually bootcamp isnt a virtual box. its a partition on your hd where you can install windows on a mac computer
vstarrydr05 said:
and actually bootcamp isnt a virtual box. its a partition on your hd where you can install windows on a mac computer
Click to expand...
Click to collapse
Duh.. been awhile since I've used MAC - you are quite correct
ok, on the flashing back either rom I get a error on line 10 trying to reflash AXURA and a error on line 12 with Cognition
Hmm. have you tried to do the factory reset from within CWM? I mean at this point.. can't lose anything by trying it.
Yeah, just did the wipe/factory reset through CWR. Still sticking on the same screen
Try this.
-Unplug the phone
-Uninstall all the current Samsung drivers you have, reboot
-Install this one, reboot
-Put the phone in download mode
-Plug the phone
Does windows install the drivers? If not continu
-Open Windows Device Manager and do a plug&play search
-If you have a ? device select it
-Right click/Update Drivers
-Select automatic...... if windows finds nothing return and select Manual.
-Choose the "Samsung ADB composite device" driver and install
Is the install successful ?
-Now unplug the usb cable
-Open Odin
-Plug the usb cable
Does Odin now see the phone ?
I bricked my phone twice. Att support center gave me a replacement each time. Just make sure you cant get to the vol up/down power screen completely screw it up
Sent from my SAMSUNG-SGH-I897 using XDA App
ronf1011 said:
I bricked my phone twice. Att support center gave me a replacement each time. Just make sure you cant get to the vol up/down power screen completely screw it up
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
Why would you brick a working phone based on a driver issue ?!
That's like blowing your car engine cause you can't communicate with onboard electronics........ unreal

[HELP] PC doesn't recognize phone after update

Hello everyone,
Alright, I've just updated my phone to the latest version Androind 2.2.1 JPY.
I was following the guide for installing Darky's ROM, but my pc doesn't show anything when I connect my phone.
I have up-to-date drivers.
When my phone was on 2.1 JM2 it was working.
I have no idea what the problem is.
I really appreciate the help and thanks in advance.
-Mick
Hi i have a similar problem, i have to connect it about 3 times for it to recognise, i am on darkys rom. anyway try this:
go into settings - wireless + networks - USB settings and select ask on connection. then try it again.
I'm not on Darky's rom yet since I can't connect to my PC.
I've just tried that a couple of times but didn't work.
does the phone connect when in download mode ? try a re flash if it does...
It does not, it also doesn't show up in Odin.
does the pc make any sounds when usb is connected ?? are you sure its not the usb cable thats at fault here ??
No sound at all. But like I said, it worked when I was on 2.1. So it's not the USB cable.
Uninstall Kies .
Reboot and reinstall Kies to give you USB drivers .
If your phone works and is set to USB mode Mass Storage connect cab;e and windows will pick up phone .
jje
Just tried it, but it didn't work.
try a stock rom
I am on a stock rom. A fresh JPY 2.2.1.
Still stuck with this problem.
have you tried a different port on the PC ? if that doesnt work u will have to try another cable to find out if its the phone or not... have u done factory reset in recovery
Yes, I've tried all the ports on my PC.
The cable is fine, because it worked just before I updated.
I'm going to try a factory reset right now.
EDIT:
Factory reset didn't work. Should I try a re-flash?
EDIT2:
Just remembered I can't do a re-flash since I can't connect to my PC whatsoever.
Did I brick my phone?
I have the same issues but I have flashed several roms none the less. I gave up on the PC after serveral PC's and several days. I think it may be a usb hardware issue as I did connect to Kies once and the PC once but then I tried the next day and I've never gotten it back on despite countless driver reinstalls, android SDK adb attempts, odin, heimdall etc...
So to flash I first installed clockwork mod as an update.zip (put it in the root folder, then boot up in recovery - you'll need 3 button mode working I think). This was in the instructions for the first VoodooDoctor rom I flashed.
I also highly recomend also getting steam recovery (mine was part of a rom so I don't know the XDA link) as it allows flashing roms that are stored on the SD card. which is handy for me as that is the only way to get something on the phone if the flash goes sideways and I didn't already have it in the root folder. It is accessible now as the update.zip in my root folder and so I can run it from clockwork.
Clockwork allows you to flash from the phone - no odin needed. Steam does the same but steam is newer so I've mainly stuck with CWM except when I had to figure out a way to fix a bad flash....
I made this post about my near death (of my sgs)
http://forum.xda-developers.com/showthread.php?t=929020
I'd still stick with the tried and true as its a little nerve racking to flash knowing that you need some function on the phone to recover but if you are dying to try a good tested custom rom I'd encourage you do so.
G

[Q] Semi-bricked, USB not recognized, doesn't even charge

Hi!
After searching the forums for a while I did not find a thread exactly matching my problem, so if I've overseen it, please just point me there.
To my problem:
I did a very stupid mistake, flashing a new custom ROM with a different kernel (as usual, cooked in Docs Kitchen) without converting back the lagfix. So I ended up with a non-booting phone - so far, so bad. Note to myself: Never flash a phone during the carnival weekend again.
So I booted into download mode and tried to recover it via Odin, but here I got my really bad surprise: USB device is not recognized, thus I Odin does not see the phone.
I tried 4 different PCs with Win7 or XP, a Linux desktop and a Macbook. I also tried 5 different USB cables (they all work with other smartphones like the Desire and the HD2). Wherever I stick the phone in, it is not recognized (code 10/code 43 in Win7). I used the stand-alone-drivers from the sticky forum thread here, and also most recent Kies versions, always the same: USB device not recognized.
Does anybody have an idea how to revive the USB connectivity? I'm almost at the point to send it in for repairs...
Or can someone elaborate how I could have killed USB with corrupting the ROM? I've to admit I do not really understand how these two are connected.
--Jens
Hi Amokbunny
You get into download mode but the PC won't recognize the phone?
That's messy and I can think of nothing that could have done that. you did not change the bootloader did you (flashed a full samsung ROM containing a bootloader, for example VJ1)?
If not I guess it's a hardware issue.
formatted to ext4 without any backup
I did a very stupid mistake too. Got darky's rom 9.3., installed i, everything worked great(really awesome thing), then i wnt to recovry mode and entered tthe speedmod and it showed mr that my phone has rtf files system not EXT4 as it should be, thou i installed the speed mode. then i chose to repartition it to ext4 but i didn't choose the backup. Just clicked to format the sd. It did formatted to EXT4, rebooted, i saw the darky's rom logo and the the phone vibrated and the logog of the droid just flashed. I tried to enter recovery mode-didn't load. Started the download mode connexted to pc used ODIN 1.7 with PDA I9000XXJPY.tar, MODEM I9000XXJPY.tar, GT-I9000-CSC-MULTI-OXAJPY-LITE.tar s1_odin_20100512.pit.
The phone has started, appeared teh stok galaxy s logo and it's just flashing. Help needed. Don,t know what to do know. I have galayx s i9000 european version.
somehow i've managed to install new firmare 2.2.1 /I9000XXJPY-baseband /2.6.32.9 [email protected] #1-kernel version, but z4root isn't working. When i start permanent root the programm ends on aquiring root shell, the debug mode is on
Got it all running, installed Darky's rom 9.3. Thanks anyway.
theduckking said:
Hi Amokbunny
You get into download mode but the PC won't recognize the phone?
That's messy and I can think of nothing that could have done that. you did not change the bootloader did you (flashed a full samsung ROM containing a bootloader, for example VJ1)?
If not I guess it's a hardware issue.
Click to expand...
Click to collapse
Yep, I can boot into download and recovery modes, but that's it.
The only apparent change in the new custom ROM was the kernel.
I also cannot really access my external SD card (it shows me some phantom files, but not the actual content of the SD), otherwise I'd try to recover it this way.
I agree with the hardware issue, if it wouldn't have coincided with the flash procedure...anyway, I think I'll send it in for repairs if I don't get it to run on this sunday.
I have the exact same problem, except that I can access my external SD. I got the problem after upgrading to Darkys Rom 9.3 the usual way, but switched from Speedmod to Voodoo. After that update, my USB didn't work anymore.
I can't get neither Xp or Win 7 to recognize my phone. USB device not recognized, and tried all the tricks. Reinstalling Kies and drivers, switching between the different modes (storage, kies media, ask, debug...) But still no USB connection.
I updated to darkys 9.5 (transferring the rom using bluetooth, and updating using CWM), but still it doesn't work.
Can get it into download mode, but still can't connect using USB and Odin.
HELP!
Did anybody ever find a solution for this?
European version of I9000, bought in Denmark. No Simlock
Same thing here after installing JV1 + Ultibread Rom 1.4... Still no solution
*shameless push*
Any solution here? I dont have that problem, but it sounds too scary to not have a working solution :S
Same prob here! Any news?
Any solution? I have the same problem.
same problem my phone is bricked while flashing a stock rom the windows disconnected the phone while flashing
ended with device not recognized even in download mode
bassem8246 said:
same problem my phone is bricked while flashing a stock rom the windows disconnected the phone while flashing
ended with device not recognized even in download mode
Click to expand...
Click to collapse
But if you are in download mode on your fone you'd rather should have a look at your configuration on the computer. Because the fone still can be flashed if the symbol for download still appears.
- Kies is shut down while ODIN is active?
- latest Samsung USB driver installed?
- Odin started with Admin?
Btw. did you try to get into recovery mode? Maybe this also still is working as the partition is quite small and chance high that it was flashed w/o faults. So you may be able to flash a zipped ROM rather than a tarball for Odin.
USB Not working when Phone plugged in... try these..
Unplug Device from PC..
Windows go to Device Manager...
Scroll down to Universal serial bus Controllers
Start with the top one and work your way down ..uninstall them all..
When done reboot Computer and let it install them all.. then try again
2.Settings --> USB Setings (under wireless & network may differ depending on Rom used) --> Try other settings Mass storage
3.Different USB ports on PC
4.Uninstall KIES from PC (reboot PC to take effect) and Reboot and just install samsung USB drivers....
5.Using windows type in msconfig in Start>Run box... windows will pop up and untick KIES from STARTUP TAB
Apply to take effect and restart machine.. try using ODIN to Flash ROM
I myself only use the Samsung USB drivers and ODIN never use KIES
or ...Check my signature and try SD formatter

[Q] Wont mount to PC or Mac

Hi all, I have scoured the web for similar issues and can't find any answers
-Captivate I897 running 2.1 formerly mounted to my MAC just fine, rooted using Galaxy-S one click root. Root was successful, mostly just removed bloatware, etc.. but alas my phone is no longer recognized by the computer, although the phone recognizes that it is connected, when I click "mount" nothing happens on the computer's end.
-Appears to be a problem with the phone, I have tried Win7 w/ Kies mini and installed/reinstalled drivers, dev mode, etc...nada. And here's the kicker - these machines will recognize and mount my GF's unrooted Vibrant just fine.
-I have a separate micro SD card reader that can read the SD card out of the phone that way.
-So, I am hoping for some help to either
1 - fix the computer recognition issue, or
2- find steps to manually update to 2.2 or unroot, etc, any ideas that will get me running 2.2 and hopefully mount to Mac or PC, using files manually loaded to the SD and installed during recovery mode, this looks like flashing, would Andromeda or Cognition fix the connectivity issue?
Thanks in advance!!
If you're rooted and can get into download mode (power off+2 volume buttons+plug usb in) then you can use this link ----> http://www.megaupload.com/?d=QL6NX702 to flash stock 2.2 firmware. Note: This WILL break your root. Here's the thread on Odin One Click as well---->http://forum.xda-developers.com/showthread.php?t=731989. You probably want to read the information there before flashing to 2.2.
Good Luck!
Thanks for the suggestion, I've tried multiple drivers, but since my PC doesnt recognize my phone, both Odin or Superoneclick dont recognize my phone also.
I was able to manually unroot by copying the One Click Root Update.zip to my phone via Wifi File-sharing app. Unroot was successful, but still no connection to PC or Mac.
I'm stuck for now, It appears that any type of flashing requires a PC connection, unless there is some way to flash completely with Wifi-copied files and using the 'reinstall packages' option?
Well, if you have a dropbox, you could drag and drop a rom (say cognition) onto your phone's dropbox. Then you'd need to find a CWM recovery (make sure it's not 3.0) update.zip and reinstall packages. This will give you CWM recovery, from which you could install Cognition from your dropbox. No guarantees it will work, but it's worth a shot.
Can't help on the Mac and I only have a dim memory of 2.1, but what are your setting under Settings/Applications for USB settings and Development? Do you have USB debugging checked (on)? Do you have the Development settings set to something weird like Kies update?
My recommendation is to put USB debugging on (checked). In that case I think the USB settings choice is disabled and therefore ignored. Then when you connect to the computer you will get a message in the notification bar on your phone saying something like "select to copy files to/from the computer". Click that, then click the mount button. You should then be able to see the extra drives on your computer by looking under My Computer or whatever (on a PC). On mine they are F and G, no special indications that they are drives on an attached phone. I also do get an automatic pop-up for the new drives, like when you insert a USB stick, but I imagine that setting could be disabled so look for the drives manually.
If you can get a com port try to do a master clear with the phone plugged in and on the entire time, then do various methods of getting into download mode if you got a com port when the phone booted up, future references I would use Odin to flash speedmod kernel to get cwm and then flash a rom or leave it as is, when I first started rooting I used the same software and got the same problem
Try installing all the drivers beforehand just to make sure
Sent from my I897 using XDA App
do u have the drivers installed?
Mr.AdAbsurdum said:
If you can get a com port try to do a master clear with the phone plugged in and on the entire time, then do various methods of getting into download mode if you got a com port when the phone booted up, future references I would use Odin to flash speedmod kernel to get cwm and then flash a rom or leave it as is, when I first started rooting I used the same software and got the same problem
Try installing all the drivers beforehand just to make sure
Click to expand...
Click to collapse
+1
My wife's phone has the exact same issue as OP. Suggestions like above are useless unfortunately as the phone does not recognize that it is connected to a computer. Instead it acts as though it is connected to a charger. The oddest thing is that if I plug it in to a computer while the phone is turned off, the phone will turn on! However, still no recognition that it is connected to a PC.
Initially when I connected the phone the first time, Win7 said driver failed to install. Then my working cappy would not connect to Win7. I had to uninstall and reinstall the drivers and restart. My working cappy connected as it should, but my wife's phone from that point refused to recognize anything but charging.
Attempts to fix Via external SD: (1) I transferred Continuum 4.1 and reinstalled. Still not recognized. (2) Transferred my recovery images from January for stock, but just became stuck on boot screen for Continuum. I am uneasy about transferring the update-recovery.zip and download folder from original backup as I do not know whether it will screw up attempts to re-enter recovery if it does not work. (3) Attempted download mode, but only works via CWM 2 (not extended menu or three button or by inserting battery with odin up trick). Even when in DL mode odin does not recognize the COM port. (4) Attempted different orders for connecting to Odin in DL mode. By orders I mean rearranging the order I connect (i.e. open odin then connect cable then go to DL). (5) transferred andromeda3 and reinstalled, still same issue.
So, I am left thinking a hardware failure occurred at some point, so I will need to open it up and check connectors to solder it possibly.
Possible non-hardware solution is to restore to stock somehow WITHOUT Odin via CWM. Anyone know if this is possible or have a link to a flashable zip?
Thanks!
edit: I am on Win7 and always made sure USB debugging was checked. Also I tried to connect via One-Click Root for the heck of it and kies mini. No luck.
flashed without a cable
Thanks for the tip jomeister 15, I was able to flash new roms dropped over wifi with CWM recovery. This got me onto 2.2 which was the main purpose of this whole adventure. I just loaded Andromeda3 and it's pretty darn impressive.
My PC and Mac still do not recognise my phone, I troubleshot extensively like Snowake and nothing is recognized. I'm convinced its a hardware issue but who cares with wireless flashing and file transfer.
snowake said:
+1
My wife's phone has the exact same issue as OP. Suggestions like above are useless unfortunately as the phone does not recognize that it is connected to a computer. Instead it acts as though it is connected to a charger. The oddest thing is that if I plug it in to a computer while the phone is turned off, the phone will turn on! However, still no recognition that it is connected to a PC.
Initially when I connected the phone the first time, Win7 said driver failed to install. Then my working cappy would not connect to Win7. I had to uninstall and reinstall the drivers and restart. My working cappy connected as it should, but my wife's phone from that point refused to recognize anything but charging.
Attempts to fix Via external SD: (1) I transferred Continuum 4.1 and reinstalled. Still not recognized. (2) Transferred my recovery images from January for stock, but just became stuck on boot screen for Continuum. I am uneasy about transferring the update-recovery.zip and download folder from original backup as I do not know whether it will screw up attempts to re-enter recovery if it does not work. (3) Attempted download mode, but only works via CWM 2 (not extended menu or three button or by inserting battery with odin up trick). Even when in DL mode odin does not recognize the COM port. (4) Attempted different orders for connecting to Odin in DL mode. By orders I mean rearranging the order I connect (i.e. open odin then connect cable then go to DL). (5) transferred andromeda3 and reinstalled, still same issue.
So, I am left thinking a hardware failure occurred at some point, so I will need to open it up and check connectors to solder it possibly.
Possible non-hardware solution is to restore to stock somehow WITHOUT Odin via CWM. Anyone know if this is possible or have a link to a flashable zip?
Thanks!
edit: I am on Win7 and always made sure USB debugging was checked. Also I tried to connect via One-Click Root for the heck of it and kies mini. No luck.
Click to expand...
Click to collapse
You could try to send a ROM, kernel, and update.zip(CWM flash) and attempt to get another ROM over it. Format the system, wipe dalvik, I don't think its a hardware issue, I had the same problem first time I tried using 1 click rooting, I just waited patiently and got a com port after about two days, so that just leads me to believe some configuration file was corrupted during flash to stock, possibly flashing a ROM or reflashing the ROM you're on with a complete wipe of the system and user data and whatnot, or possibly just doing a backup up from cwm and immediately restore it, if its charging I highly doubt its hardware
Sent from my I897 using XDA App

[Q] Zero connectivity in download mode. £10 for solution. :)

Okay a little backstory:
I was on an early version of CM9 but as i am selling the phone i decided to put a more stable version of it on there and downloaded CM7 -stable.
I flashed this in CWM and it worked fine.
I gave it a quick test and noticed all the google apps were missing, most importantly the market. So i booted into recovery and realised i had forgotten to put the zip on the SD card.
I then went into mounts and mounted USB, nothing happened...
From that point onwards the phone would not talk to the PC. even if i booted up into the phone, it would just show it as charging. I could not find any options in the menus for USB options.
After some extensive reading, i tried a few things, none of them had worked. I found a post mentioning some kernels have issues with USB, so i downloaded the recommended one and flashed it in CWM.
After rebooting, CWM was now orange and not blue and the option to flash from external card has gone.
I have also done some digging and there is a good posibility that the kernal that i flashed was for the GT I9000 (which is the american one, right?)
So as it is at the moment:-
I can get into CWM.
I can get into download mode through the 3 button combo.
I can get into download mode using home made jig.
I can boot the phone, but it boot loops.
I can not get the phone to be detected on the pc.
Things i have checked:
Cable will connect other phones.
Tried different cable to be sure.
Phone used to be detected, but downloaded drivers through kies again to be sure.
Closed Kies using task manager.
Nothing is coming up in network connections in device manager when phone is connected.
I'm out of ideas now, so £10 PayPal donation for anyone that comes up with the solution to fix it
If i can get it detected, i can use Odin to flash what i want.
Sounds like a drivers problem. You may need the 'Google driver' developer.android.com/sdk/win-usb.html
When I had bootloops when I first installed CM9 I used heimdall to flash a the stock CM9 kernel. This gave me back CWM.
heimdall flash --kernel 'kernel.zip'
In the commandline.
Thanks for that,
I already had the Google USB drivers from when i installed the SDK to make some apps.
So i then gave Heimdall a try (Graphical Version), it seemed to suffer the same problem.
Reporting "Failed to detect compatible download-mode device."
I seem to remember the GUI saying I didn't have the correct drivers and it downloaded them for me.
The other thing worth a try is changing the USB port and reinstalling the correct drivers on that port.
I've not seen anything like that, it has not asked me for any drivers.
It's like the phone is not connected at all. nothing will detect it, i have even tried it on another PC.
Sorry, I'm not sure what you mean by installing on a port.
Well sometimes changing USB port will allow you to install new drivers. Although if you've tried it in another computer and it doesn't work then changing port may not help.
Does the phone appear in device manager when it's connected and in download mode?
Nope. Not coming up at all in the device manager. It didn't when it was booting fine. And it still doesn't in download mode. :-( I'm thinking the usb connector on the phone might be faulty.
But it was working up until trying to mount the USB in CWM
Sent from my GT-N7000 using XDA App
I don't suppose you have access to a Linux PC do you? Windows USB drivers are notoriously sucky. If you could plug it into a Linux PC and type 'lsusb' at a command line, that would at least show you that the device is really there.
I think I have a spare pc kicking around that I could use. I'll give it a go when I get home tonight.
Sent from my GT-N7000 using XDA App
Remove all the drivers completely from device manager for Samsung, then install fresh drivers and connect the cable when in download mode, hopefully it will recognize it
Are you sure the connector is clean? e.g. maybe there's dust in it.
I had that problem once, the connector was full of fabric fibers from some coat's pocket I had the phone in.
Suggestion 1 (Linux): I installed ubuntu, did not detected anything to even install any drivers. Detected my new phone fine.
Suggestion 2 (Uninstall drivers from device manager): I could not find any drivers named with the name Samsung in there.
Suggestion 3 (Clean port): I have some compressed air that i sprayed inside, it does look pretty clean and will continue to charge but still not connection on the pc.
To install the drivers for heimdall you have to run zdiag from inside the driver folder. Had to do this earlier on, the phone the other appeared as something other than Samsung composite usb or whatever it normally says
I tried this, and it displayed 9 devices after selecting show all. I seemed to recognise all of the items in the menu.
To be sure, I then disconnected the phone and re ran it to see if one of the items were missing, but it was the same number.
I too had problem with the usb connection on my i9000, and I was pretty sure my usb connector on the phone is somewhat damaged since it sometimes can only go to charging mode without being detected by my pc as a usb device. CWM instal is fine but ODIN can only detect the phone without able to flash the rom to the phone. The flashing will always stuck at the message "Setting Up Connection", I waited for 15 minutes and the flashing will eventually died. I retry the odin flash for 40 to 50 times and eventually the flashing will go through one time. Tried heidmall command line and the result is the same.
I have problem with Odin in the past. I bought a new laptop, running Win7 64 bit. Installed Samsung Kies to install the correct USB drivers for the phone. Then made sure that Kies wasn't running in the background. So tried using Odin. Odin was detecting the phone, but it was hanging at initialising connection. Odin was working fine on my old laptop running Win7 32bit. Long story short, I was having a few issues with my new laptop, reinstalled Win7 64bit, now Odin is working fine, have flashed the phone a few times using the new computer.
After flashing which kernel you started facing this problem?
Wipe ur phone,re-flash CM7(flash the nightly 181,it's completely stable),uninstall KIES,uninstall old usb drivers,install these usb drivers http://forum.xda-developers.com/showthread.php?t=961956 ,check that USB storage mode is set as Mass Storage and then connect your phone. Also try enabling/disabling USB debugging
lovedonator said:
After flashing which kernel you started facing this problem?
Wipe ur phone,re-flash CM7(flash the nightly 181,it's completely stable),uninstall KIES,uninstall old usb drivers,install these usb drivers http://forum.xda-developers.com/showthread.php?t=961956 ,check that USB storage mode is set as Mass Storage and then connect your phone. Also try enabling/disabling USB debugging
Click to expand...
Click to collapse
The point at which i could no longer mount the USB was when i selected "mount usb" from CWM. I later installed a new kernal which downgraded my CWM, removing the install from external SD option.
So I cant flash a re-flash a rom unless i can it onto the phone which without the USB working is near impossible.
Xyis said:
The point at which i could no longer mount the USB was when i selected "mount usb" from CWM. I later installed a new kernal which downgraded my CWM, removing the install from external SD option.
So I cant flash a re-flash a rom unless i can it onto the phone which without the USB working is near impossible.
Click to expand...
Click to collapse
You can directly download the ROM on your internal sd using dolphin browser or opera mobile
I can't do that either as the phone is currently boot looping.
Sent from my GT-N7000 using XDA App

Categories

Resources