Related
First of all, I have checked around quite a bit on this forum as well as others to try and avoid having to ask a question that's already been answered. Here's my problem/ what happened. I was rooted (one-click with locked bootloader) and had tried out several roms for a couple of months now. A few days ago I reverted back to an old stock 2.2 backup. My phone received two ota updates and I'm pretty sure I lost root. I had just went on using the phone for about two days when I ran into a problem today. After shutting the phone off I have now become "stuck" at the initial "X" screen (not animated). I pulled the battery and tried again several times. I then tried to reboot into recovery from the bootloader/ 3 skateboards screen with no luck. Any time I hit recovery it simply takes me back to my stuck "X" screen. I have an entire backup of my SD card from earlier as well as at least 4 nandroid backups (one of which was the stock 2.2 before the latest ota). I am thinking I need to somehow put clockwork recovery back on my phone so I can restore to one of my backups. I do not know how to do this. Sorry for the lengthy post but I want to provide as much information as possible. Any help at all would be greatly appreciated.
Just like you restore to stock 2.2. You should have used recovery.img. use adb fastboot to put the stock or anom recovery. I am not am expert but I have had the same problem few times. Always use adb commands
Sent from my Nexus One using Tapatalk
Does my n1 have to be in usb debugging mode because it's acting like it's not connected or something. I get the message "error: device not found." I'm on the fastboot screen on my n1 and using terminal on a mac. I usually didn't leave debugging mode on
No it doesn't but you have to have the drivers installed as well as the SDK with dependencies.
Whew! Thank God! I ended up getting a FRG33 stock rom onto the sd card and the bootloader detected it. I'm not sure what happened but when I tried recovery after that it took me to the android with an "!" point (meaning no recovery?) and then back to the X. This time however it loaded on through and went right back to the way it was before it was stuck. Again, not sure what happened but thanks for the replies and help.
fastbook oem unlock
install Amon RA recovery
flash new rom.
Caseyp789 said:
Whew! Thank God! I ended up getting a FRG33 stock rom onto the sd card and the bootloader detected it. I'm not sure what happened but when I tried recovery after that it took me to the android with an "!" point (meaning no recovery?) and then back to the X. This time however it loaded on through and went right back to the way it was before it was stuck. Again, not sure what happened but thanks for the replies and help.
Click to expand...
Click to collapse
The exclamation mark is just the stock Android recovery - it was re-installed when you loaded the stock FRG33 ROM.
Performing OTA updates requires you to have the stock recovery installed. Simply reverting to a stock 2.2 nandroid isn't sufficient, so trying to install those OTAs (which should have failed without stock recovery) may have broken something there.
GldRush98 said:
fastbook oem unlock
install Amon RA recovery
flash new rom.
Click to expand...
Click to collapse
This is by far the easiest (and safest) way. Google/HTC provided us an easy and safe method for gaining full access to our phones.... Why so many people refuse to use it is beyond me. If you root it the proper way (with fastboot oem unlock), it will make recovery from any further issues a lot more simple.
From what I can tell, I am having the same symptoms as the topic creator. I believe the problems started during a failed flash of cyanogenmod 6, but I am not sure by what means the flashing took place.
I can't boot the phone normally, it hangs on the X splash screen and the same occurs when trying to enter recovery mode.
I have tried the passimg approach to fix this, it either doesn't recognize my zip or starts loading it and freezes on a loading bar.
Fastboot flashing recovery completes, but doesn't fix the issue.
I can fastboot flash every image partition except system or radio, both hang.
As danger rat and dude random both know, I have posted this problem on the nexus one forums but I thought I'd post here to have some more minds look at it.
Hi all,
I have had my N1 for 1year and two weeks now (yes, warranty just expired). I was charging the device and it seemed to overheat and reboot. I unplugged it, took the battery out, let it rest for a bit and tried to boot it again. The phone now gets stuck on the X logo (not moving) and never boots.
I'm currently abroad (in the UK) and can't have it sent back for repair (I'd have to pay the repair too).
Will rooting the phone and installing an alternate OS fix my phone?
Is there any way to get HTC to honor the warranty after two weeks of expiration (I've been getting this problem for a while now, but that was only an issue if I made extensive use of the device while charging, which I almost never do so I didn't bother.)
Is there any way to fix this issue without messing with rooting? I'm abroad right now and all I want is my phone to work.
Any suggestions are welcome.
Try booting into bootloader from power off (vol- pwr) if that doesn't work then try the 3 figure salute (pwr vol- tb) your phone should boot into fastboot then just select bootloader.
If either of these work the your good you can get the static x fixed all you need to do is passimg (search wiki if you don't know what it is) as for the charging problem passimg will factory reset the phone so if that doesn't fix it then no you'll need to try rooting or it might be hardware.
Yes, I'm able to go into the bootloader.
I tried clearing the storage, choosing fastboot, etc. The phone seems to be working, just won't boot past the static X.
From your last reply, you're saying passimg has good chances to fix my phone. What does that involve? Do you have a link to a how-to that I could follow (it would really be a bad time for me to brick my phone, a good how-to would be really appreciated).
Cheers!
Yes passimg is used for many things it just reflashes a shipment ROM to the phone through bootloader. Like I said you can visit the wiki to have a how to here is a link http://forum.xda-developers.com/wiki/index.php?title=Nexus_One/Guides_%26_Tutorials scroll down to "Unroot / Restore your Nexus" then follow the instructions. This should restore you to frg33 then you just need to update back to 2.3.4.
NOTE: this will wipe your data.
Ahh there's a way to unroot the nexus one now!
I had no idea! This is good to know (last time I checked was in December I think).
I will give that passimg a try as soon as I get home.
Can anyone confirm that this ("Attention: Latest stock ROMs don't flash using PASSIMG.ZIP method. Use the provided latest Froyo PASSIMG, and upgrade it after flashing.") means I can still reflash using this if I have the latest ROM (2.3.4) but will simply have to update again after (which I might not do given the issues I'm facing).
Cheers!
Confirmed - Dude is giving you good info... xD
Just to verify, unrooting is not the same as relocking. If you unlocked your bootloader (have a little lock symbol under the X screen), there is no way to relock it.
But the passimg is a good option. It will take you back to an older version of Android, and then you just let the system update itself.
Since you are out of your warranty, I can highly suggest looking into custom firmwares. These give you a lot more features and in many cases, perform better. CyanogenMod is probably the most popular one. These will fully replace your Android OS. CyanogenMod really doesn't even differ in look from stock all that much. Most people probably wouldn't even have a clue they are running something different, except for the stability and performance increases.
You can read up about this stuff in the wiki as well.
Oh, I see, thanks for the info.
I'm actually trying to get the FRG83 passimg file but the link is dead. Does anyone have an alternate one?
Use the FRG33 image
Alright,
I unlocked the device, used fastboot to write the recovery "Amon_Ra's Recovery".
Then I rebooted, went to the bootloader (trackball + power), went to "recovery" but the phone still gets stucked on the X (with the unlocked padlock logo).
Any advices?
Try the passimg, but it's possible that you are looking at hardware failure...
ldiamond2 said:
Alright,
I unlocked the device, used fastboot to write the recovery "Amon_Ra's Recovery".
Then I rebooted, went to the bootloader (trackball + power), went to "recovery" but the phone still gets stucked on the X (with the unlocked padlock logo).
Any advices?
Click to expand...
Click to collapse
If you are still running stock Android, you can't reboot between installing the recovery and getting into it. Stock Android will replace it. Try to go back to the bootloader and select recovery then, or fastboot to load the recovery, and then use fastboot to boot off of it.
Code:
fastboot flash recovery "c:\location to\recovery.img"
fastboot boot recovery "c:\location to\recovery.img"
Hopefully this will get you into Amon_RA so you can try again.
But the passimg method is used in the bootloader, not in recovery. You don't need a custom recovery to use the passimg method.
Amazing, thanks for pointing out my mistake, that give me a little bit of hope now . (I was at the point where I'd open the thing and look for a broken solder joint.)
I will try this as soon as I get home!
**Edit** I actually am not sure if I really rebooted or went straight to recovery. I'll update this thread tonight.
According to some other people, this would be a common issue with the internal memory dieing.
Is there a utility I can use to check the state of the memory?
None that I know of. Our phone internal memory uses the yaffs2 (Yet Another Flash File System v2) file system. I haven't heard of any programs that can check it.
Same situation
Hello, all. I haven't signed in on here in ages just because I've been so happy with how my Nexus has been running.
I ran into the same problem as OP stated.
I think I have some sort of hardware issue because my phone used to randomly freeze and couldn't be restarted unless I pulled the battery. Now it's at the point where I can't even turn it on because nothing happens when I press the power button or if I try to boot into recovery. This is really frustrating.
Is there any way to check for hardware damage? My warranty is over as well so I'd have to pay for any repairs to my phone if I sent it in.
If it's running, you can try to pull a log, and see what error reports you get?
andythefan said:
Now it's at the point where I can't even turn it on because nothing happens when I press the power button or if I try to boot into recovery. This is really frustrating.
Click to expand...
Click to collapse
Your power button might just be dead. Try having the phone plugged into a power source and removing and reinserting the battery. While you are doing that, hold the Volume Down button. This will get you into the bootloader which would allow a passimg to be performed. Hopefully your reboots aren't a hardware problem.
So , after pulling my battery, pulling the sim and the sd card, it finally turned on and went to recovery without freezing. I was able to wipe and reflash cyan 7. It's working well for now, but I'm really afraid this is going to happen again because this isn't the first time that it's just froze repeatedly.
Does anyone know what the problem could be?
Alright,
I did "fastboot flash recovery MYIMG" then "fastboot boot MYIMG", didn't work.
Then I tried "fastboot flash recovery MYIMG" then go to bootloader (without rebooting) and selected recovery.
Still no luck.
It always freezes on the static X logo. What else can I do? Will using passimg be any different (I don't have any way to put the file on the micro SD card but I can manage to do it if it's worth the shot).
Thanks
Ok, so after using clockwork rom manager on my nook color and seeing how convenient it was, I thought, "hey maybe this would be good on my milestone." WRONG. I flashed the clockwork recovery (they even had an option for milestone) and when I rebooted into recovery from the software (either in rom manager or the reboot power option) it just rebooted straight into android. When I held the power and camera keys, it just took me to bootloader.
Under rom manager, there was also an option to flash the RA recovery, but that didn't seem to help (exact same behavior as clockwork recovery).
I'm currently running the CM7 mod and prior to this fiasco, I was using RA 1.7 (pretty sure). edit: RA 1.7 was my girlfriend's HTCmagic, I just remembered that I would have had some version of openrecovery on this phone.
So, I guess my question is, what are my next steps here? I'd really like to stop flying without a recovery. My only shred of an idea was to flash a stock image from rsdlite and set my milestone all the way back to stock and then reroot and re everything, but if someone has a better idea, I'd be very open to that as my plan seems like a big hassle.
A) not really the place for this post but anywa
B) you should beable to just flash the Vulnerable recovery http://android.doshaska.net/rootable then you can install a recovery from this forum thats for our phone!
Apologies, I didn't mean to step on any toes. Could a mod please recategorize this thread.
I will check out that link and report back if I need further assistance. Although, if that's a surefire way to fix my problem, I should be fine. Thank you for your fast (and succinctly informative) reply.
Tyfighter said:
Apologies, I didn't mean to step on any toes. Could a mod please recategorize this thread.
I will check out that link and report back if I need further assistance. Although, if that's a surefire way to fix my problem, I should be fine. Thank you for your fast (and succinctly informative) reply.
Click to expand...
Click to collapse
Quite alright if you have any more problems feel free to just PM me
Check this thread:
http://forum.xda-developers.com/showthread.php?t=1139120
Well, the good news is, that I flashed the vulnerable recovery and I'm able to boot into recovery. The bad news is, it only lasts for a few seconds. I see the standard recovery icon and then a bar fills up and then my phone reboots into android. From what you said, I take it that there's another step in here where I take another file from the forums and then install that as well. Is that just through RSD lite then?
Tyfighter said:
Well, the good news is, that I flashed the vulnerable recovery and I'm able to boot into recovery. The bad news is, it only lasts for a few seconds. I see the standard recovery icon and then a bar fills up and then my phone reboots into android. From what you said, I take it that there's another step in here where I take another file from the forums and then install that as well. Is that just through RSD lite then?
Click to expand...
Click to collapse
Ok so you need to take an open recovery for example http://forum.xda-developers.com/showthread.php?t=1091787 and extract it to the root of your sdcard so you have a update.zip file and openrecovery folder.
Then boot into recovery and press the volume up and camera button and a menu should come up.
Then select the 'flash update.zip' and this should 'boot' you into the custom recovery, sadly because of the looked bootloader we must do this everytime we wish to boot into recovery
Okay, I have that file, or one similar, from when I originally had started using custom roms (and updated/changed them etc.).
The problem is that before, when I'd go into recovery, it would have the icon of the phone out of the box with the exclamation mark or whatever, and it would stay there indefinitely.
Now, it only stays for a few seconds before rebooting into android. A little bar appears, fills up, then reboot. Doing the volume up + camera combo only serves to expedite this process (i.e. reboots as soon as I press it).
zacthespack said:
Ok so you need to take an open recovery for example http://forum.xda-developers.com/showthread.php?t=1091787 and extract it to the root of your sdcard so you have a update.zip file and openrecovery folder.
Then boot into recovery and press the volume up and camera button and a menu should come up.
Then select the 'flash update.zip' and this should 'boot' you into the custom recovery, sadly because of the looked bootloader we must do this everytime we wish to boot into recovery
Click to expand...
Click to collapse
what your doing (power + camera) is meant to put you into the bootloader mode... to get into recovery, hold 'x' on the physical keyboard and then hold the power button. This will get you into recovery. Hope this helps.
~D
are you sure that you did in fact flash the vulnerable bootloader, and not a newer, non-vulnerable one? sounds like that.. exploit fails, system reboots. also, if you are running an original rom right now, it does check the bootloader every reboot and flashes the non-vulnerable one!
Tyfighter said:
Okay, I have that file, or one similar, from when I originally had started using custom roms (and updated/changed them etc.).
The problem is that before, when I'd go into recovery, it would have the icon of the phone out of the box with the exclamation mark or whatever, and it would stay there indefinitely.
Now, it only stays for a few seconds before rebooting into android. A little bar appears, fills up, then reboot. Doing the volume up + camera combo only serves to expedite this process (i.e. reboots as soon as I press it).
Click to expand...
Click to collapse
I'm a bit confused with how you're getting into Recovery mode, but the way to enter recovery is to hold Power + X, then Camera + Vol Up when you see the Motorola Logo.
I'm getting into recovery the same way I always have Power+camera then volumeup+camera. Power+DpadUp is how I've been getting into bootloader. Power+X actually yields nothing, just a regular boot.
Unless the file hosted on the site that was linked earlier in the thread is a newer, nonvulnerable recovery then, yes, I'm sure I flashed vulnerable recovery. I'm going to attempt to flash again. Just to see if maybe that's the issue.
I'm pretty sure I'm seeing it at least attempt to enter recovery, which is a step up from before (before being that it just went to bootloader). Because I'm seeing the image that displays in the recovery menu, but then it brings up a progress bar (which I never saw before) and when that fills up (in about 2.5 seconds), that's it. Reboot.
Thanks everyone, for all the help though.
EDIT: Despite RSD lite saying that the process as a success, the reflash did nothing.
Tyfighter said:
I'm getting into recovery the same way I always have Power+camera then volumeup+camera. Power+DpadUp is how I've been getting into bootloader. Power+X actually yields nothing, just a regular boot.
Unless the file hosted on the site that was linked earlier in the thread is a newer, nonvulnerable recovery then, yes, I'm sure I flashed vulnerable recovery. I'm going to attempt to flash again. Just to see if maybe that's the issue.
I'm pretty sure I'm seeing it at least attempt to enter recovery, which is a step up from before (before being that it just went to bootloader). Because I'm seeing the image that displays in the recovery menu, but then it brings up a progress bar (which I never saw before) and when that fills up (in about 2.5 seconds), that's it. Reboot.
Thanks everyone, for all the help though.
Click to expand...
Click to collapse
Where did you get the VR sbf? android.doshaska.net/rootable ?
Yep, that's the one.
EDIT: Finally got up the guts to load the official Telus sbf into RSD lite and pull the trigger. It seems like this is probably beyond salvage now. Once again, many thanks to everyone, and if all goes well, I hope to only be in the ranks of the unrooted/unmodded for a few minutes.
EDIT the second: Okay, so flash to stock went perfectly. Everything works, including recovery, but not openrecovery. I can get to the menu to flash the .zip, but it fails the esignature check. Which I'm assuming points to Vulnerable recovery not flashing correctly or perhaps my file is corrupt, or maybe something more exotic and exciting. I flashed SHOLS_U2_03.11.0 if that's relevant.
For those interested, everything is up and functional again.
I had to first flash back to stock, then flash the vulnerable recovery located at http://modmymobile.com/forums/downloads.php?do=file&id=28089 , then the standard, boot to recovery, blah blah blah, install a new rom.
Let this be a lesson to the rest of you; Clockwork Rom Manager does not, I repeat, does NOT seem to work on our milestones. Which is a real shame...
I realize this is a double post, but I'm just so darned jubilant to be able to update my rom again.
Droid 4 running Stock Jb 4.1.2, Safestrap 3.11, Liquid smooth 2.9, CM (last stable)
Everything working fine for a number of months, installed Liquid smooth via -> delete romslot 3, create romslot 3, install Liquid 2.8.
It ran for a number of days no problems. Restarted fine, all features worked great, even the annoying random restart from 2.4 went away.
6 - 10 days in, im surfin' the news sites at work, put it down, screen goes black, i pick it up. Hit the power button cause i realize its off and it just boot loops... so bad i had to vol-/+ pwr, go to flash mode and THEN turn it off b/c it just kept trying to restart, hang on logo.
I got home and decided to AP flash the latest:
9.8.2O-72_VZW-18-2
Blur_Version.98.72.182.XT894.Verizon.en.US for the maserati.
Boot looped a few times, i was able to get it to go into recovery mode, after that it loaded up the stock JB system. First boot it crashed and restarted, second boot it loaded but only the keyboard worked, not the touch screen. Went to the in OS option of factory reset mode + delete storage.
Rebooted, worked. Checked it a few boots, everything is fine. I use Druid 4 Utility Xt894 JB version and apply the root. Works great. Install safestrap, Create new partition, install liquid smooth 2.9. Works for an afternoon... at work today the touch screen stops responding, i restart it a few times. I try to enter recovery mode. Now im in boot loop again...
I've tried re flashing it again, a few times. I tried even going down to the previous release of JB for the phone. STILL 4.1.2!!!! But nothing.... it just boot loops... what did i do wrong? It was running great. No tweaks or anything done to it prior to it having its melt down.
Help please.. ive provided as much information as possible and though i only joined XDA now to post for help, i have read it for a long time as my main source for my phone and have donated to both CM and Liquidsmooth teams previously..
help!!!
I can't see where you are doing anything wrong. You have obviously done your research and have a good idea of what you are doing. I see, after you fastbooted, you went back to Liquid. I think I would try running CM10.1 or even stock for a few days and see if you have the issue there as well. If you do than it sounds to me like it might be a hardware issue. If not, maybe try re-downloading Liquid. Perhaps your zip got corrupted somehow.
I would love too. In fact i would be willing to run it on the stock crappy 4.1.2 if i could get it out of boot loop this time...
It just keeps boot looping on the logo. AP Fashboot flash and BP flash work but recovery and normal boot/reboot mode just goes into M logo boot loop.
I've re downloaded the 4.1.2 jb SBFs from 2 different sources to ensure its not a corrupt file, tried 18_1 and 18_2 software versions...
Is there a way to use the abd shell to get into the filesystem and check whats going on? Is the SBF the last call? or is there another route to see whats going on or just flash EVERYTHING? Like completely back to stock?
I can find my way around a PC file system but im not familiar with linux. Please help me understand, Is it like having CMOS and BIOS settings or equivalent to damaged CMOS firmware? What am i not replacing/reverting by SBF and HOW can i replace/revert BEYOND the basic sbf...
If ya point me in a direction or to someone who can help me out i can do all the foot work just point me in the right direction?
Is this applicable? I found a site talking about using CWM in a ADB shell file push to possibly get access to more features?
The article also goes into reading the busybox / ADB command screen? (sorry for not proper jargin) and see what its doing during the boot loop before it restarts?
Id add the link but i need more posts....
Update: Flashed 18_2 again with a "factory cable" i made, let it boot loop a series of times before it started up into the stock system again.
At first, again the touch screen wouldn't work, random lockups and restarts, etc. Since i just got it into the main system again and i had to leave for the weekend for a trip(no wifi or network), i couldn't mess with it all weekend but i left it on the whole time and kept checking its functionality... gradually its come back to full function. Touch screen works and is accurate, no more lockups, no more restarting, even stopped boot looping when i restart and enter recovery..
Im not sure and i couldn't find any forum converstations or write ups to support to idea but i think after a major crash and you flash new or reflash your SBF, it seems the phone needs time to recalibrate and index? Not sure, but just an FYI. Gonna try loading SS and liquid again.
Very noobish issue. Rooted, unlocked bootloader on Atrix HD. Set up SafeStrap as recovery. Everything checked and working. After letting SafeStrap install Cyan 10.3 and rebooting, phone entered CyanogenMod boot screen and become stuck for an hour. Realized that I forgot to reset and wipe all stock settings and cache (yes, I know that should have been obvious step). Figured I could just go into SafeStrap and make the quick fix.
Seems that I'm unable to enter my custom recovery, instead I'm lead to the familiar bricked android stock recovery. No options to access stock rom (assuming it was deleted during install or lost, etc). Tried installing a different recovery, but fastboot on PC is unable to find device. Help at this point is very much appreciated, either to do any of the following:
1. Somehow access SafeStrap again (assuming that it wasn't wiped aswell) so I can clear stock settings and cache, get Cyan 10.3 going properly.
2. Instructions/links to another method to otherwise forcibly delete stock settings and cache (please keep in mind, fastboot is currently unable to find device).
3. Otherwise completely clear phone of EVERYTHING, then reinstal stock recovery and or/stock ROM so I can give up on flashing custom and stick with stock.
*Update:
Was finally able to get phone into AP Fastboot Flahsh Mode. My computer itself can't see the phone, but device manager shows it as "Fastboot QINARA S" and I'm able get a response through my PC's end of flashboot.
Tried using RSD lite to install a stock ROM, but no success since the phone isn't off and can't be turned off without trying to go into another Boot Loop. Also tried installing a new recovery through fastboot, but I keep getting the response, "(Bootloader) variable not supported."
At this point, I'd be really happy if I could get the proper commands to wipe and factory reset my phone while in fastboot. At least then I'd have Cyan. I could try installing stock if it continued to glitch.
Update Motorola drivers on your computer and check threads for fastboot files from skeevydude.
Sent from my MB886 using XDA Premium 4 mobile app
Well safestrap is for use with locked bootloaders so there lies your problem. Maybe you can make a factory cable or buy one to put your phone into fastboot so you can flash stock through rsd.
Sent from my PACMAN MATRIX HD MAXX
http://forum.xda-developers.com/showthread.php?t=2226527
Sent from my MB886 using XDA Premium 4 mobile app
SkunkID said:
*Update:
Was finally able to get phone into AP Fastboot Flahsh Mode. My computer itself can't see the phone, but device manager shows it as "Fastboot QINARA S" and I'm able get a response through my PC's end of flashboot.
Tried using RSD lite to install a stock ROM, but no success since the phone isn't off and can't be turned off without trying to go into another Boot Loop. Also tried installing a new recovery through fastboot, but I keep getting the response, "(Bootloader) variable not supported."
At this point, I'd be really happy if I could get the proper commands to wipe and factory reset my phone while in fastboot. At least then I'd have Cyan. I could try installing stock if it continued to glitch.
Click to expand...
Click to collapse
The error is from using the wrong fastboot executable. Look at post 5. If you get a stickybit error, search our general forums for "stickybit" and you'll find that fix.
deeje00 said:
Well safestrap is for use with locked bootloaders so there lies your problem. Maybe you can make a factory cable or buy one to put your phone into fastboot so you can flash stock through rsd.
Sent from my PACMAN MATRIX HD MAXX
Click to expand...
Click to collapse
With a bit of creativitity one could use SSR to dual boot Holo Blur and Batakang....or two custom 4.3's that use the same kernel....PAC + Carbon both with arrrghhh's kernel.....Only problem is ya can't be a noob at all if ya do it.
Solved issue...somehow.
Used method shown in link below to install stock recovery image since Safety Strap was apparently deleted/wiped/banished?
(can't link, still noob poster. Just search, "[Guide] How to flash back to Stock Rom - chacha. Please Sticky This !", should be the first result.)
After installing stock recovery, was able to go to the standard dead android screen, but after punching the volume buttons randomly, the option menu for stock recovery opened. Was able to factory reset and wipe cache, then properly reboot. Cyanogenmod finally got out of it's BootLoop, and everything seems to be running fine. Flashed a non-official CWM (no offical CWM or Twrp avaliable for Atric HD) and got Gapps. Phone is finally running fine.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Lingering issues worth mentioning incase there are obvious fixes.
.Cyan likes to crash whenever running programs for the first time or doing do much activity in a short amount of time (I suspect the cache has something to do with the cleared cache since revisiting apps doesn't cause crashes as often). If it persists, I'll probably just back up and look for a more stable rom.
.All notification lights are white, except the battery notification lights, despite me changing the colors and/or allowing apps to use their own light settings.
When you're at the "dead Android" screen pressing Vol Down + Power pushes it into recovery, iirc - might seem random but there's a purpose behind it.
SkunkID said:
Solved issue...somehow.
Used method shown in link below to install stock recovery image since Safety Strap was apparently deleted/wiped/banished?
(can't link, still noob poster. Just search, "[Guide] How to flash back to Stock Rom - chacha. Please Sticky This !", should be the first result.)
After installing stock recovery, was able to go to the standard dead android screen, but after punching the volume buttons randomly, the option menu for stock recovery opened. Was able to factory reset and wipe cache, then properly reboot. Cyanogenmod finally got out of it's BootLoop, and everything seems to be running fine. Flashed a non-official CWM (no offical CWM or Twrp avaliable for Atric HD) and got Gapps. Phone is finally running fine.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Lingering issues worth mentioning incase there are obvious fixes.
.Cyan likes to crash whenever running programs for the first time or doing do much activity in a short amount of time (I suspect the cache has something to do with the cleared cache since revisiting apps doesn't cause crashes as often). If it persists, I'll probably just back up and look for a more stable rom.
.All notification lights are white, except the battery notification lights, despite me changing the colors and/or allowing apps to use their own light settings.
Click to expand...
Click to collapse
Hi, I am having the same issue you had... how the heck were you able to get back into stock recovery? Every time I try my phone just reboots and gets stuck again. I cant even turn off my phone with out it rebooting. I have read your posts and followed that other forum you mentioned but if I cannot boot into recovery and if my computer cant see my phone it wont work. Please help when you get a chance.