odin failed! - Galaxy Tab Q&A, Help & Troubleshooting

Hi, i have galaxy tab:
PDA: XWJMG
PHONE: XXJMA
Now i started ODIN 1.7 and selected p1000-mck-r3-ext4-cwm.tar in PDA. I didnt select Re-Partition and did not tick anything and did not select PIT file. Now when i connect it says 'added' and when i click on start it goes through the process and says "failed' in the end. Now my tab shows yellow triangle on it. Help

Do you by any chance have locked bootloaders? Anyway as long as the computer recognizes your tab you can fix it. Just use search.
Sent from my Desire HD using XDA App

Robi-K said:
Do you by any chance have locked bootloaders? Anyway as long as the computer recognizes your tab you can fix it. Just use search.
Sent from my Desire HD using XDA App
Click to expand...
Click to collapse
I dont know about bootloader, its an untouched piece. Please tell me how to fix this tab... :-(

Look at the stickyes in the gsm tab development. Just download a rom that doesn't contain bootloaders and flash it via odin. Again you can find such roms in the development section. Read read and read again and you will be able to fix your tab. One question, why did you flash your tab in the first place?
Sent from my Desire HD using XDA App

Download this firmware http://files.deodexed.com/ModADroid-Galaxy-Tablet/Rotohammer/JME/
Then goto http://forum.xda-developers.com/showthread.php?t=932082 & read the bit where it says if your tab does not boot...
Hope this helps
Mark
You need to dload the P1 hidden pit & full J4 version fw

Is it maybe because the rom you selected says cwm? Isn't that supposed to be flashed in clockwork mod?

Thanks guys for all your help, i flashed pit to my phone via ODIN and piece is alive and working now and gave the tab back to my friend. Now just need to know for the future i have ODIN v1.31 and P1_EUR.pit. I selected pit and P1000JPJJ2 on PDA. Now just need to know before flashing do i need to select repartition?

As i read through the tutorial you only select repartition when you are flashing with the pit file!
If you are installing firmware, Flash the custom kernel that is linked on the same page as the overcome rom 2.13 without partition, Then hold vol up and power will put you in recovery mode, You can flash the rom through there useing the install zip from sdcard option but you must copy the custom rom onto the sd card first....
Regards
Mark

slyevo said:
As i read through the tutorial you only select repartition when you are flashing with the pit file!
If you are installing firmware, Flash the custom kernel that is linked on the same page as the overcome rom 2.13 without partition, Then hold vol up and power will put you in recovery mode, You can flash the rom through there useing the install zip from sdcard option but you must copy the custom rom onto the sd card first....
Regards
Mark
Click to expand...
Click to collapse
Well, i know how to flash custom rom, just wanted to flash the firmware through odin since it seems easier...i downloaded P1000JPJJ2 from the following site and it says no repartition, my problem solved..thanks anyway
http://www.thegalaxytabforum.com/index.php?/topic/112-samsung-galaxy-tab-firmware-list/

i have the same problem like the first post. I am using P1000 for asia (malaysia). now i can do nothing with my tab but odin still able to detect it. anyone could help forward me the link for the said rom without bootloader. the link given in the previous post already dead.

andrew21 said:
Hi, i have galaxy tab:
PDA: XWJMG
PHONE: XXJMA
Now i started ODIN 1.7 and selected p1000-mck-r3-ext4-cwm.tar in PDA. I didnt select Re-Partition and did not tick anything and did not select PIT file. Now when i connect it says 'added' and when i click on start it goes through the process and says "failed' in the end. Now my tab shows yellow triangle on it. Help
Click to expand...
Click to collapse
I had the same problem earlier and then i learned that bootloader for stock JM is signed so it show error ... completion (write) failed ... when you try to upgrade or install custom rom using Odin. I reverted back to resurrect my tab by Odin with pit (follow pit version) and check repartition, auto reboot. It works for me but not sure if it will work for others. Good luck.

Related

Odin - "Check image files!!"

I've got Odin to recognize my Captivate. I clicked start and it tells me to check the image files. I haven't mounted anything into Odin but I have the ROM & firmware I want on my desktop. Any idea what I'm supposed to do at this point ?
KC108 said:
I've got Odin to recognize my Captivate. I clicked start and it tells me to check the image files. I haven't mounted anything into Odin but I have the ROM & firmware I want on my desktop. Any idea what I'm supposed to do at this point ?
Click to expand...
Click to collapse
it all depends on what version of ODIN you are using. there are One Click Odins for stock JF6 2.1 and JI6 2.2
if you are using the standalone ODIN, you need to point the pda section to the rom and depending on what rom you are loading, you may need the pit file, phone (modem) file, and CSC file.
explain a little bit better what you mean by you have the ROM and firmware on your desktop?
Hi,
I also got my samsung galaxy s gt-i9000 (in download mode) hooked up to odin (multi downloader 4.03), but whenever i try to flash a custom rom (created in romkitchen.org) it keeps saying ''check the image files !!'' i selected the 'one package' option, and i selected the rom at the bottom ''select integrate package'' section..
I'm clueless right now, please help?
Berry1988 said:
Hi,
I also got my samsung galaxy s gt-i9000 (in download mode) hooked up to odin (multi downloader 4.03), but whenever i try to flash a custom rom (created in romkitchen.org) it keeps saying ''check the image files !!'' i selected the 'one package' option, and i selected the rom at the bottom ''select integrate package'' section..
I'm clueless right now, please help?
Click to expand...
Click to collapse
wait. you made a CWM flashable rom from romkitchen, and you are trying to use ODIN to flash it???
wtf
and not to mention you are on the captivate section.....not the i9000 section
if you keep this up you will have a brick in no time

[Q] Indian Tab Flashing Information ?

Could some one for benefit of Indian Tab Owners, write a step-by-step instructions or guide. Lot of information to digest for a new user including details of 1) rooting 2) installing recovery 3) flashing ... this information would be great useful for everyone.
My Tab details :
(Model: GT-P1000 | Code: INU | Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)
hey..even i have a galaxy tab indian version...just follow the guides that are avaliable here for rooting flashing etc...etc...and i had the same modem when i bought it but its since been upgraded to a newer version of the modem so i just updated the modem to the ...DXJM2 version..thought the asian modem would be better for me..if u want i'll post the modem.bin
Dare{D}evil said:
hey..even i have a galaxy tab indian version...just follow the guides that are avaliable here for rooting flashing etc...etc...and i had the same modem when i bought it but its since been upgraded to a newer version of the modem so i just updated the modem to the ...DXJM2 version..thought the asian modem would be better for me..if u want i'll post the modem.bin
Click to expand...
Click to collapse
Thank you for quick reply. I started compiling the files need to flashing. So far, I could do following. Please advice me whether I am on the right path or not.
1. Rooted my tab with Z4root. Now I got root permission.
2. Downloaded Odin3 v1.7.exe and s1_odin_20100803.pit for flashing
3. Downloaded Roto-JMI-Full-v2.zip and Roto-JMI-Upgrade-v2.zip
Now, using Odin PDA button, I want to flash Roto-JMI-Full-v2.zip ?
Few questions:
a) Is this correct way of flashing or I am missing something?
b) Does above flash install Recovery also ?
c) which files need for PHONE and CSC files ?
d) Which firmware best suitable for Indian Tab ?
Thank you in advance for clarifying above.
I really appreciated reply for my questions as it would allow me to move forward. I will ensure a good documentation at the end of the process for benefit of other users.
nchary05 said:
Thank you for quick reply. I started compiling the files need to flashing. So far, I could do following. Please advice me whether I am on the right path or not.
1. Rooted my tab with Z4root. Now I got root permission.
2. Downloaded Odin3 v1.7.exe and s1_odin_20100803.pit for flashing
3. Downloaded Roto-JMI-Full-v2.zip and Roto-JMI-Upgrade-v2.zip
Now, using Odin PDA button, I want to flash Roto-JMI-Full-v2.zip ?
Few questions:
a) Is this correct way of flashing or I am missing something?
b) Does above flash install Recovery also ?
c) which files need for PHONE and CSC files ?
MId) Which firmware best suitable for Indian Tab ?
Thank you in advance for clarifying above.
Click to expand...
Click to collapse
Install Adfree or something which requires root acess for installation. Once rooted download something like root explorer from market which allows you to backup the modem.bin file. Or me or somebody else can just upload the file here.
Read the post/link in the thread where you downloaded Roto's JMI rom.
Use the .pit file from Roto's link not the thing which you posted...same place where you got the same ROM file. If you are flashing first time/from another rom then use the Full v2 zip file. Else use Update v2 when flashing from one of Roto's rom.
Connect the tab to your pc, reboot and go into download mode...press power+vol down button while rebooting...a yellow triangle icon with an android digging will come up...to get out of download mode,just keep the power button pressed till it rebooted normally.
Once in download mode, open up Odin and check that the yellow com box option is on. Check repartition option to ensure everything is wiped and you have a fresh install from scratch.
For PIT select the pit file downloaded from roto's link
For PDA select the Full.tar file
For PHONE select the modem.bin file
For CSC leave it blank...
Once done, recheck and hit start.
PLEASE CHECK ROTO'S JMI V2 THREAD IN THE DEVELOPEMENT SECTION...it has a link to howto which is old but gives some idea of how to proceed...for pit, pda, phone follow as I suggested and things will go fine...
Sent from my GT-P1000 using XDA App
Thank you.. I will do the same let you know the status....
blackheart2925 said:
Install Adfree or something which requires root acess for installation. Once rooted download something like root explorer from market which allows you to backup the modem.bin file. Or me or somebody else can just upload the file here.
Read the post/link in the thread where you downloaded Roto's JMI rom.
Use the .pit file from Roto's link not the thing which you posted...same place where you got the same ROM file. If you are flashing first time/from another rom then use the Full v2 zip file. Else use Update v2 when flashing from one of Roto's rom.
Connect the tab to your pc, reboot and go into download mode...press power+vol down button while rebooting...a yellow triangle icon with an android digging will come up...to get out of download mode,just keep the power button pressed till it rebooted normally.
Once in download mode, open up Odin and check that the yellow com box option is on. Check repartition option to ensure everything is wiped and you have a fresh install from scratch.
For PIT select the pit file downloaded from roto's link
For PDA select the Full.tar file
For PHONE select the modem.bin file
For CSC leave it blank...
Once done, recheck and hit start.
PLEASE CHECK ROTO'S JMI V2 THREAD IN THE DEVELOPEMENT SECTION...it has a link to howto which is old but gives some idea of how to proceed...for pit, pda, phone follow as I suggested and things will go fine...
Sent from my GT-P1000 using XDA App
Click to expand...
Click to collapse
I followed the steps after flashing 'full' tar, it rebooted tab, started the normally. After that, I verified that, all applications , phone (GSM) and wifi working fine.
Now my question is do I really need to flash *second* tar file ? what is it for ?
^^No. It is only for people upgrading from previous versions! You are good to go!
Now, I want to install CWM recovery. Please some one can confirm below steps:
1. Make sure to have Samsung Kies installed, and your tab at least connected once, to be sure the drivers are correct.
2. Your Tab must be Rooted.
3. If you wish to do a backup, now is the time.
4. You will need an SD Card with enough free space for the filesystem conversion, and to put the Overcome ROM on before we start. (An empty 4gb should be plenty, as long as it is empty, or close too)
5. Download and Extract the following file to your computer: http://www.apksmash.com/corodius/galaxytab.zip (Contains "Odin3 v.1.7.exe" "Overcome_Kernel_v1.0")
Now, we will Install the Kernel and perform the EXT4 filesystem conversion.
1. Turn off your Galaxy Tab.
2. Turn your Galaxy Tab on into DOWNLOAD mode (Press Volume DOWN and Power On at the same time).
3. Open Odin3 v1.7.exe on your PC.
4. Connect your Galaxy Tab to your PC via the USB cable.
5. Make Sure the ID:COM box is highlighted yellow (meaning it sees your tab).
6. Click on the PDA button and select the Overcome_Kernel_v1.0.tar file you downloaded earlier (make sure PDA is ticked after selecting the file).
7. The only boxes ticked should be:
A. Auto Reboot
B. F. Reset Time
C. The PDA tickbox
8. Click start and wait for PASS! to show highlighted green on Odin.
9. Your Galaxy Tab will Reboot, and get stuck on the Samsung Boot Screen. This is fine.
10. Turn your Galaxy Tab off by holding the power button for about 5 seconds.
11. Turn your Galaxy Tab on into RECOVERY mode (Press Volume UP and Power On at the same time).
12. The Galaxy Tab will now perform the EXT4 conversion.
13. Sit tight, depending on how much data you have, this can take quite a long time.
14. Once finished, click reboot system now (by pressing the power button).
At this point, You have installed the Overcome Kernel with CWM included and converted the Filesystem to EXT4. It has been reported that many stock ROMs will boot and run fine now, however some may not, but it just depends on your ROM etc.
http://forum.xda-developers.com/showthread.php?p=11713685.
Would be there any problem ? or is there any easy way to install CWM Recovery.
I had bricked my tab while modding battery icon and it was not booting now. Now i want to flash with the custom rom available here. I am noob to flashing so just want to confirm the steps mentioned above applicable to the bricked tab. Can somebody guide me for bircked tab.
Please mentioned the good custom rom with Ext4 conversion at the time of install. I am using indian tab.
@OP:- Sorry for hijacking this thread but find some info here for my queries
Can you get into download mode? If yes then you should be able to flash...but I would suggest checking"I bricked my tab" threads in general or developement section...
Sent from my GT-P1000 using XDA App
nchary05 said:
Now, I want to install CWM recovery. Please some one can confirm below steps:
1. Make sure to have Samsung Kies installed, and your tab at least connected once, to be sure the drivers are correct.
2. Your Tab must be Rooted.
3. If you wish to do a backup, now is the time.
4. You will need an SD Card with enough free space for the filesystem conversion, and to put the Overcome ROM on before we start. (An empty 4gb should be plenty, as long as it is empty, or close too)
5. Download and Extract the following file to your computer: http://www.apksmash.com/corodius/galaxytab.zip (Contains "Odin3 v.1.7.exe" "Overcome_Kernel_v1.0")
Now, we will Install the Kernel and perform the EXT4 filesystem conversion.
1. Turn off your Galaxy Tab.
2. Turn your Galaxy Tab on into DOWNLOAD mode (Press Volume DOWN and Power On at the same time).
3. Open Odin3 v1.7.exe on your PC.
4. Connect your Galaxy Tab to your PC via the USB cable.
5. Make Sure the ID:COM box is highlighted yellow (meaning it sees your tab).
6. Click on the PDA button and select the Overcome_Kernel_v1.0.tar file you downloaded earlier (make sure PDA is ticked after selecting the file).
7. The only boxes ticked should be:
A. Auto Reboot
B. F. Reset Time
C. The PDA tickbox
8. Click start and wait for PASS! to show highlighted green on Odin.
9. Your Galaxy Tab will Reboot, and get stuck on the Samsung Boot Screen. This is fine.
10. Turn your Galaxy Tab off by holding the power button for about 5 seconds.
11. Turn your Galaxy Tab on into RECOVERY mode (Press Volume UP and Power On at the same time).
12. The Galaxy Tab will now perform the EXT4 conversion.
13. Sit tight, depending on how much data you have, this can take quite a long time.
14. Once finished, click reboot system now (by pressing the power button).
At this point, You have installed the Overcome Kernel with CWM included and converted the Filesystem to EXT4. It has been reported that many stock ROMs will boot and run fine now, however some may not, but it just depends on your ROM etc.
http://forum.xda-developers.com/showthread.php?p=11713685.
Would be there any problem ? or is there any easy way to install CWM Recovery.
Click to expand...
Click to collapse
I followed above steps and could able to install CWM RECOVER.
congrats dude
maddy_in65 said:
I had bricked my tab while modding battery icon and it was not booting now. Now i want to flash with the custom rom available here. I am noob to flashing so just want to confirm the steps mentioned above applicable to the bricked tab. Can somebody guide me for bircked tab.
Please mentioned the good custom rom with Ext4 conversion at the time of install. I am using indian tab.
@OP:- Sorry for hijacking this thread but find some info here for my queries
Click to expand...
Click to collapse
can you just tel me which modem.bin are u using coz i was planning to flash but stuck on decision bcoz of modem... is it jpz or jk3? or any other
A new GB version is available DDJPA
http://forum.xda-developers.com/showthread.php?t=1226674
need PDA PIT PHONE CSC files
Kindly send me the links for downloading the PDA PIT PHONE CSC files as I could find only broken links.
My samsung tab (Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)) is bricked and won't boot.
Than You
nchary05 said:
Could some one for benefit of Indian Tab Owners, write a step-by-step instructions or guide. Lot of information to digest for a new user including details of 1) rooting 2) installing recovery 3) flashing ... this information would be great useful for everyone.
My Tab details :
(Model: GT-P1000 | Code: INU | Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)
Click to expand...
Click to collapse

[Q] ODIN - Check image files !! Works for others though...

So I've downloaded the following kernels from a link here on XDA that should be swapping kernels to allow me root on my recently upgraded, stock ROGERS 2.3.3 Captivate. Odin is telling me to "Check image files !!" when I load the .tar files into the Select Intergrated Package (and yes, the one package switch is on). I opened the tar to double check it wasn't double-compressed.
What else would be giving me this problem? I'm using Odin 4.28. Curiously, it is showing my phone as detected, my phone IS in downloading mode, but Odin just says (Android) in the Title, no specific model. But it says it's found it on COM 6. <1> Added!! and Detected!!
It's when I load up the kernel tar's and try to start that it yells at me. Is this triggering anything in anyone's mind that I'm doing wrong? Or do I need to provide more info?
I am using Vista 32-bit (legit) on a Dell studioXPS. And I ran it as administrator.
never heard of ODIN 4.28. i think its only up to version 1.82 or so.
sounds like you are using the wrong ODIN
Pirateghost said:
never heard of ODIN 4.28. i think its only up to version 1.82 or so.
sounds like you are using the wrong ODIN
Click to expand...
Click to collapse
Yeah. That is def the wrong version of Odin. Download the i9000 bootloaders in my sig. Unzip it. Delete the pda.tar.md5 file. Use the included version of Odin (1.82 I think) to flash your kernel.
Alright, quick question - I accidentally flashed the phone, not the pda. I tried to flash the KH2 modem back via phone but ODIN failed. Kies is currently not detecting the phone, and so I decided to try flashing the PDA while I had it open and I would figure the modem out after. ODIN hung, so I closed it and rebooted out of downloading mode and got the Phone ! Computer error. So I figure now I have to flash back to the stock rom and start over again, but this time I would like some advice as to which step to take next. I downloaded I896UXKH2-HOMEBINARY.tar.md5 from another thread here. Can I flash this with Odin - and if so, which is the place to load it? Bootloader? PDA? Phone? CSC? I have no PIT files.
Think it goes into the pda slot. Go back to the thread t you got it from and read the first post of the thread. Also restart your computer before trying to flash again.
can someone upload the modem.zip, please thank you

can't boot into recovery

After installing the lastest "S.U.R.F.A.C.E" ROM on my GT-I9000 I'm presented with the Galaxy S logo and nothing else,
Tried and tried vol up + home + power number of times now with no avail.
Everything was working fine before was able to boot into clockwork recovery ect, unfortunately I do not have a usb cable so can't try odin any help would be great.
Grab yourself a jig from ebay or the likes, or make one
http://forum.xda-developers.com/showthread.php?t=819551
It will boot into download fine the problem I have is it won't boot into recovery is there any way I can wipe it or does it look like I am in need of a cable?
Then reflash back to stock using Odin
What were you flashing from as surface is an oxeded rom, not dexeded.
buttwad said:
What were you flashing from as surface is an oxeded rom, not dexeded.
Click to expand...
Click to collapse
clockwork recovery, i take it I messed up here so
No, meant what rom were you on before your flash? Stock?
oh sorry got the phone of a friend looked like a custom samsung rom, build version was easyprojectv2 if that rings any bells?
Looks like the problem was caused by trying to flash a odexed rom over a deodexed rom, or not having the correct bootloaders for the new rom. Normally before a flash I would return to stock (firmware from sammobiles.com) first via ODIN, do all the wipes, flash a kernel so you have a nice clean install to 'abuse'. Then I would add any custom rom from there be it by ODIN or by cwm.
Grab yourself a usb lead, nice clean flash and start again.
Ok so I've 3 file here:
APBOOT_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
CODE_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
KERNEL_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
s1_odin_20100803.pit (not sure if i need this as was in the root of the odin folder not the firmware?)
Where do the other 3 file go PDA PHONE CSC???
I am also stuck on the same front, i donwloaded rom from samfirmware but it only had PDA part and nothing else, please suggest which official rom should i download??
stevek93 said:
Ok so I've 3 file here:
APBOOT_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
CODE_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
KERNEL_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
s1_odin_20100803.pit (not sure if i need this as was in the root of the odin folder not the firmware?)
Where do the other 3 file go PDA PHONE CSC???
Click to expand...
Click to collapse
I would go this way mate, first grab JVT from sammobiles.com ( register first)
Flash that using ODIN
Comes with 3 files, CSC, PHONE and PDA
PDA file goes to PDA in ODIN
PHONE goes into MODEM in ODIN
CSC goes in CSC in ODIN.
Also select PIT file, should be 512 on the PIT section on ODIN, hit start and it will flash then reboot.
Then open ODIN again, connect phone and flash your KERNEL to the PDA section of ODIN.
Then grab this http://forum.xda-developers.com/showthread.php?t=1117579
and flash using cwm.
Your then on JW1 all rooted and ready to play.
put the "APBOOT_I9000XWJW1_CL788890_REV03_user_low_ship.tar" file into the PDA and flashed it. Everything seems to be working fine might stick with the stock for a while never really needed to be rooted.
ok i just popped the SIM and have no network access when i tap on Mobile Networks in the setting it tells me to insert a SIM????
the firmware i had was wrong didnt have a modem. Downloaded a jvt as buttwad said flashed an now everything working perfect now. cheers mate!

Unbrick Samsung Galaxy Note GT-N7000

Having looked at the thread regarding a similar predicament that I have (http://forum.xda-developers.com/showthread.php?t=1783556), I'm keen to know I can use ODIN to put on a new ROM. Basically these are the steps I've followed;
1. Used KIES to update my ROM from Gingerbread to ICS
2. Use ODIN to update root my phone with CM9 safe kernel (not knowing it would have been significantly better to have copied my new AOKP ICS ROM to the internal SD card first)
3. Rebooted my phone and cannot get past 'SAMSUNG GALAXY NOTE GT-N7000' logo.
4. I can still boot into download mode and use ODIN but wondered how I should use it to install a ROM as none of the ROM's I've downloaded, are in the correct .tar, md5, smd format, that OSIN is looking for ?
Some pretty basic reading for you: http://forum.xda-developers.com/showthread.php?t=1321268
Enjoy.
Moved To Q&A​
Please do not start question threads in the development section​
baseliner said:
Having looked at the thread regarding a similar predicament that I have (http://forum.xda-developers.com/showthread.php?t=1783556), I'm keen to know I can use ODIN to put on a new ROM. Basically these are the steps I've followed;
1. Used KIES to update my ROM from Gingerbread to ICS
2. Use ODIN to update root my phone with CM9 safe kernel (not knowing it would have been significantly better to have copied my new AOKP ICS ROM to the internal SD card first)
3. Rebooted my phone and cannot get past 'SAMSUNG GALAXY NOTE GT-N7000' logo.
4. I can still boot into download mode and use ODIN but wondered how I should use it to install a ROM as none of the ROM's I've downloaded, are in the correct .tar, md5, smd format, that OSIN is looking for ?
Click to expand...
Click to collapse
First of all, I'm not sure if this is the answer your looking for, but here is it anyway.
IN PC ODIN, there is a 'PDA' button (same button you flashed your kernel to), you need to download the ROM's zip file and flash it from there.
Stock ROM file you download is zip, you need to extract it one time to get into .tar, then you can use that file with pda of odin.
Sent from my GT-N7000 using xda premium
dr.ketan said:
Stock ROM file you download is zip, you need to extract it one time to get into .tar, then you can use that file with pda of odin.
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
Would these be the files needed to get my phone back up and running? I am new to Android and screwed my phone up after a factory reset, now it just reads downloading for ages and does nothing. I still get a screen that reads Hyperdroid RedPill Recovery when i power on with volume button up pressed. Volume down I get Android man and it reads downloading but does nothing.
I have looked all over for this situation but seem to get a piece here and there and not the exact same issue all in one so I am reluctant to just do something and make it worse.
Please advise
That is downloading mod, it won't do anything but remain as it is, if you don't do anything.
You need to connect you device to PC in this state and have to use odin
Read 1st line on my sign and read post#2, you will get full instruction, how to use odin.
Sent from my GT-N7000 using xda premium

Categories

Resources