Database Develop

Pls Help my Wizard. it stopped @85% and wont start now

i was installing WM5 on my wizard when it gave an error at 85% and stopped. only starts in bootloader but wont install a new one. whats the solution?
thanx

Well... we'll need a little more info in order to help. What is your current ipl/spl? What ROM were you trying to upgrade to? Did you get any kind of error message when the RUU stopped?

was 2.24
and i wanted higher so i downloaded one of the O2 roms
ruu gave a "file not good for ur fon" kinda error

Well.... get into bootloader mode (press the voice button while starting the device until you get the three colored screen) and you can flash the original rom again.
Did you CID-unlock your device first? No? Read read read before flashing again. Start at the sticky.

thing is, how do i flash the fon in bootloader mode?

If you connect it to the pc it will say USB at the bottom of your device screen. You can just flash at this point. No need for activesync. If no USB appears on the screen than you're not in bootloader mode.

ruu says no connection cos it always tries to check the current version first.

Flashing WM6 - have I got this right?

Just got my Trinity today, and have successfully unlocked it using pof's unlocker. I unlocked the SIM lock and the CID lock, so it's now SuperCID.
I want to put WM6 on it, the LVSW version. I've downloaded the three files in the sticky post. Before I do it, I want to check that I'm understanding it right, because I'm a bit confused with version numbers.
So...
1) First, I need to HardSPL by running the "ROMUpdateUtility.exe" file from the Hard-SPL.zip file, yeah? I ran this (but didn't flash it) and was confused because the new "Image Version" was 1.20 whereas the Image Version shown in the "current image" bit was 1.24.xxx. Usually, going backwards is bad but I may be misunderstanding.
2) I then need to flash the Radio ROM to 1.41 - why do I need to do this? I guess I run the "ROMUpdateUtility.exe" from the GSM_xxx_xx file, right?
3) Finally, I need to flash WM6 - by running the "ROMUpdateUtility.exe" file from the WM6 zip.
Is that right?

Just tried to flash both the HardSPL and the Radio ROM, and the ROM Update Utility always craps out after I select "Yes" to the security prompt on the Trinity.
"ERROR 246 DEVICE NOT RESPONDING" is displayed in the update utility. Any ideas?
Also, if I go to the bootloader manually (holding down the buttons) the version numbers are:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
But when I let the ROM Update program enter the bootloader, these are shown instead:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
What does it all mean? Very confusing! It won't let it update anyway, when I select "Yes" to the security prompt, the screen goes black, the ROM updater throws up the error 246 and then the Trinity shows the bootloader.

GazChap said:
Just tried to flash both the HardSPL and the Radio ROM, and the ROM Update Utility always craps out after I select "Yes" to the security prompt on the Trinity.
"ERROR 246 DEVICE NOT RESPONDING" is displayed in the update utility. Any ideas?
Also, if I go to the bootloader manually (holding down the buttons) the version numbers are:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
But when I let the ROM Update program enter the bootloader, these are shown instead:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
What does it all mean? Very confusing! It won't let it update anyway, when I select "Yes" to the security prompt, the screen goes black, the ROM updater throws up the error 246 and then the Trinity shows the bootloader.
Click to expand...
Click to collapse
SPL by Des is a one time only SPL called SSPL-TRIN.exe, it's somewhere on this board. Sometimes it's baked into a ROM too ... it fakes the SPL.
HARD SPL stays on your phone .... doesn't need SPL by Des anymore.
Windows needs some time to switch from Windows CE to the bootlader driver. This can cause an error ...... just start the exe file again on the PC.
Another common flash error is with Vista, then you need to overwrite the default driver when you're in the bootloader. The driver is in "VistaRUU.zip"
Relaunch the Hard-SPL, then the radio ROM and after that LVSW or mUn's ROM.

There is a file you extract called EnterBootLoader.exe
I copy this to the Memory card.
Then before I run the update I run this on the memory card.
The phone goes to the boot loader and then once windows has re-detected it I run the update.
This seems to have eliminated all problems I've ever had flash updating.

akirainblack said:
There is a file you extract called EnterBootLoader.exe
I copy this to the Memory card.
Then before I run the update I run this on the memory card.
The phone goes to the boot loader and then once windows has re-detected it I run the update.
This seems to have eliminated all problems I've ever had flash updating.
Click to expand...
Click to collapse
I just tried this, but Windows doesn't seem to want to detect the presence of the device when I do. ActiveSync reports that nothing's connected.

Well I've got the Hard-SPL and Radio ROM to flash - instead of leaving ActiveSync connected I just went into the bootloader manually and did it that way.
But now I'm trying to flash WM6 and it gets up to 8% and then craps out with Error 286 - communication errors.
The device now won't boot past the bootloader
What do I do now?

Bloody hell. It's amazing, it really is.
I had it plugged into my USB hub.
Took it out and plugged it directly into the PC, just on the off-chance that the hub was screwed up.
It's all working fine now, I think!
Typical. Thanks for the assistance anyway guys.

Nps. Glad you got it sorted
Is the USB Hub powered? If not that will cause a ton of problems!

It's supposed to be powered, but I'm starting to think that the power supply might be faulty!

hi guys,
2 questions if i can;
1)What is HardSPL?
2) Why are there 3 steps to getting WM6? why can I not use the "ROMUpdateUtility.exe" file from the WM6 zip straight away?
Thanks a lot!!

Same Problem as GazChap
Hey All,
I was having the exact same problem as GazChap with the same configuration to start out with.
This is what I did:
1)plug in my p3600 to the USB
2)let synchronize, and hopefully finish, otherwise stop it
3)run HARD-SPL; this usually freezes after the first go and stalls in the bootloader
4)run HARD-SPL again; this time it will finish. You will have to turn on your machine again after this.
5)run AX3L ROM 2.0.8.2; this ALSO usually freezes after the first go and stalls in the bootloader
6)run the ROM again; This time its gonna work...
Now it works..

brick time
I loaded the hard spl succesfully. I could not get the radio upgrade to load no matter what I did. My instructions said it was optional, so I went directly to the WM6 rom exe load and it has a perpetual communications error after about 8% even though the WM6 loader says each time that recovery is successful. I have a tricolor screen (bootloader?) on my 3600 which won't respond to anything I have thought of yet. Anything I can do other than pitch it? Help! And thanks in advance.

ok, just want to make it short: (P3600 user)
1. I have WM6.1 ROM (FleNover 3.3 Black edition) installed.
2. When I want to downgrade to WM6 official, after 20% it goes error.
3. Now, it only shows 3 colors.
4. Here is my PDA information in 3 colors:
TRIN100
IPL-1.00
TRIN100 MFG
SPL-1.30.Olipro
5. When I want to upgrade with WM6 official, after my PDA shows the progress bar, it restarted and the update screen shows Error 286.
6. How do I fix it?
thank you very much

money against help

After hours !!! trying almost every advice I don`t know what to do ! I would for the help !
hardspl process
I did everything what is written here and it still doesn`t work:
step by step:
- this is ONLY for warranty reasons. i.e. the device needs repair and you have to send it to htc to get it serviced. if you plan to restore hardspl then don't even bother flashing this stock package, unless you are some kind of hacker/dev
- IMPORTANT: be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
- now the steps
1. download the stock spl package from this post.
2. download X1_HardSPL_v1 too, from this post.
3. run the hardspl package, but do not press Next button i.e do not go ahead with flash yet.
4. at this point, take the extracted stock SPL, a RUU_Signed.NBH file, and overwrite the other RUU_Signed.NBH in hardspl package.
Yes it should go to tricolour screen now and say 0.52.OliNex.MFG (this is SSPL!).
"Hard-SPL flashes, device automatically reboots, job done"
THIS never happened but it seems that I do have the hardspl done !
BUT - the next problem when I run the RUU process I get always the error message "update error 262" which is a coomunication error.
Is there hope for me ?

What exactly are you trying to do?
and please stop posting the same thing over again, people will answer you when they get a chance!
If you are trying to get to Hardspl then why are you trying to flash back to the stock spl??
Follow the proper instructions..
http://forum.xda-developers.com/showthread.php?t=431218
From the start of the post to the 3rd lot of stars ****
If you are trying to return to stockspl having already flashed Hardspl then you wont be able to flash any more roms except the stock one.

OK !
My steps:
0a) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en done
0b) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobi...ce-center.mspx
1) download Hard-SPL package from attachment, extract to an empty folder. done
2) it is recommended you download only the X1_HardSPL_v1.zip unless you want to tinker with MFG SPL (MFG SPL 0.52 is a separate attachment). only X1 done
3) you must Have Phone Synced with PC in Windows Mobile! done
4) run X1_HardSPL.exe. (if you want to flash MFG SPL: at this point replace the extracted RUU_Signed.nbh with the MFG version of RUU_Signed.nbh) done
5) follow steps in the RUU, and check on the device for prompts after PC shows loading bar. done
6) it should go to tricolour screen now and say 0.52.OliNex.MFG (this is SSPL!). done !!!
7) Hard-SPL flashes, device automatically reboots, job done. THIS doesn`t happen !

****
then once the screen is in SSPL (tricolour screen saying 0.52.OliNex), run RUU on the PC (i.e. the rest of the hardspl package) manually.
****
Have you tried this?

fards said:
****
then once the screen is in SSPL (tricolour screen saying 0.52.OliNex), run RUU on the PC (i.e. the rest of the hardspl package) manually.
****
This next step is not possible because X1 and PC are never connected !
Click to expand...
Click to collapse

At the moment I`m working with the sd way but getting the answer "no image file"

the coloured display is saying
Kovs110
SPL-0.72....
microp1...
microp2....

My htc hd not loading OS

Hi, my htc hd starts with 'smart mobility R1.14.25.24
D1.59.48753' and goes to windows version 6.1 initial screen (preparing for first use), then restarts again. I checked the boot loader screen and it comes with
blac100 32m
spl -1.54.0000
microp-blackstone led v6.
I did try to do USPL v2.5, i get the message 'usb port can not be opened'.Would someone please help to get my phone working? Really appriciate any help.

Hi,
Maybe try to flash with other rom, using SD card.

valanxda said:
Hi, my htc hd starts with 'smart mobility R1.14.25.24
D1.59.48753' and goes to windows version 6.1 initial screen (preparing for first use), then restarts again. I checked the boot loader screen and it comes with
blac100 32m
spl -1.54.0000
microp-blackstone led v6.
I did try to do USPL v2.5, i get the message 'usb port can not be opened'.Would someone please help to get my phone working? Really appriciate any help.
Click to expand...
Click to collapse
Put your phone into its bootloader and try to run USPL.exe. Did you remember to disable antivirus?

Fallen Spartan said:
Put your phone into its bootloader and try to run USPL.exe. Did you remember to disable antivirus?
Click to expand...
Click to collapse
Thanks. I did disable the antivirus. still not working.
Yesterday I tried orange ROM 'OrangeUK_HTCTouchHD_1.59.61.2_Radio_52.64.25.34_1.14.25.24_Ship_phone_software', hoping it would make the phone working. The update was successful, but the same problem.

valanxda said:
Thanks. I did disable the antivirus. still not working.
Yesterday I tried orange ROM 'OrangeUK_HTCTouchHD_1.59.61.2_Radio_52.64.25.34_1.14.25.24_Ship_phone_software', hoping it would make the phone working. The update was successful, but the same problem.
Click to expand...
Click to collapse
Try to install a newer version of the HSPL.

If you can't get USPL to work, have you tried HSPL? Your using a rom based on 1.56+ so you'll need to use HSPL 1.56

I just tried HSPL. I followed the thread http://forum.xda-developers.com/showthread.php?t=505377. Flashing for dummies. When I run the first step 'HSPLWrapper_Blackstone_156OliNex', it sits on 0% for long time and finaly came up with error msg. I tried the option 'recovery', but no use. I have done a hard reset. Still same position where it started. . I'm very sad now..

valanxda said:
I just tried HSPL. I followed the thread http://forum.xda-developers.com/showthread.php?t=505377. Flashing for dummies. When I run the first step 'HSPLWrapper_Blackstone_156OliNex', it sits on 0% for long time and finaly came up with error msg. I tried the option 'recovery', but no use. I have done a hard reset. Still same position where it started. . I'm very sad now..
Click to expand...
Click to collapse
What error message do you get? There should be an error code eg 260 or 262 etc. The different errors have different meanings and different solutions to fix them.

Update error (262). The ROM Update Utility has encountered a communication error during the update process.
I thought I could do the manual option. But hd doesnt go beyond the first windows screen.

valanxda said:
Update error (262). The ROM Update Utility has encountered a communication error during the update process.
I thought I could do the manual option. But hd doesnt go beyond the first windows screen.
Click to expand...
Click to collapse
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.

valanxda said:
Update error (262). The ROM Update Utility has encountered a communication error during the update process.
I thought I could do the manual option. But hd doesnt go beyond the first windows screen.
Click to expand...
Click to collapse
Error 262 is a very common error.
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.
Click to expand...
Click to collapse
Try to reboot and try to rerun a few times. If this doesn't work you will need to run the manual sspl.
Troubleshooting - manual SSPL
* Boot up your phone.
* Copy SSPL-Manual-TouchHD.exe to your phone. In a file browser on your phone browse to where you copied SSPL-Manual-TouchHD.exe and run it.
* Your phone will reboot into its bootloader and should show SPL v 1.07.OliNex.
* When it shows USB at the bottom then run HSPLWrapper_blackstone_156OilNex.exe from your computer again.
* If bootloader now shows 1.56.olinex you can then flash to your new rom.
Click to expand...
Click to collapse
When you say you tried the manual solution is this what you meant. You may need to reflash to your stock (original) rom first and then run manual sspl from there.
As this is now becoming a flashing problem, please post further responses in the Dummies Guide thread and I'll help you there. This thread will probably be closed soon.

As per post above, please post in dummies guide thread
Thread closed

[Resources] Flashing your First CDMA Rhodium Rom (For Noobs)

This tutorial is for flashing RHOD400 & RHOD500 CDMA+GSM Global phones.
In this tutorial some good ROM links are given also.
Thanks to xda members OliNex, mskip, cajunflavoredbob, HTC0017, wizardknight, arrrghhh
To install / flash new ROMs in your device you have to follow 2 major steps
1. Flashing HardSPL
2. Flashing the ROM
Now, I strongly suggest all of you to kindly download the proper STOCK ROM for your device because if anything goes wrong, you can switched to your main shipped ROM.
Check if your device is GSM or CDMA(GSM+CDMA), read this Post
GSM Stock ROMs here
CDMA Stock ROMs here
These are the steps to be followed.
1. Flashing HardSPL
NOTE: If you already installed HardSPL in your RHOD400, RHOD500 device, you will not need this update.
: it's like with previous Hard-SPL unlockers - every user gets one free use of the Hard-SPL, further use is subject to paying 3GBP per each device. However, if you are a private user, you can have other uses free on request if needed, such as using it on a replacement device.
the license is valid forever and all this works as transparently as possible, so for normal users nothing is noticable.
Preparations:
0) this package is for Rhodium CDMA-GSM worldphone version only (CDMA Touch Pro 2, not the original Touch Pro) devices. only RHOD400, RHOD500 modelids are accepted. this Hard-SPL supports WM6.5.
1) if you have Vista / Windows 7, WMDC update to 6.1 (or whatever is latest) is recommended.
Steps:
1) download newest RhodiumW Hard-SPL package and extract this to an empty folder.
2) you must Have Phone Synced with PC in Windows Mobile!!! the device needs to be connected to Activesync or WMDC via USB cable. and it must not be in Flight/Airplane mode (i.e. the phone part should be on).
3) internet access is required as the program checks online for updates and for the license.
4) run Rhodium-HardSPL.exe on your PC, make sure it's launched from a local drive (not through network drive, etc.). running it on XP requires Admin logon, and Vista/Windows 7 will automatically prompt to allow it to run in Admin mode, so allow it please.
important: if you get an antivirus warning, please ignore it, it contains no harmful code (just used a packer to compress it). if you encounter DEP errors, then add it to the exception list in DEP settings.
5) follow steps as prompted in the Hard-SPL program. if this is the first run of Hard-SPL on a device after hard reset, you must select Automatic flash mode (the first button in Welcome screen).
notes: you should usually go for Automatic flash mode; the Manual flash option is only to be used as noted below - any other errors triggered while running in Autoflash mode will have to be fixed as instructed in the error message.
6) it will ask you to wait while it prepares for the flashing, press OK.
7) now it should go through without any error messages, if one does pop up, then please follow the instructions included in the error text. if no specific instruction is shown, then ask for help in the forums, but this should not ever occur (as this means a really fatal error occurred).
at this point the device did hopefully went to a black screen. this is the SSPL version, which is temporary. then RUU (Rom Update Utility) will instantly launch.
9) some notes: when RUU says it will perform a hard reset and cause data loss, do not worry, it is not going to do this. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
10) SPL flashes, device automatically reboots, job done.
11) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 1.00.OliNex, which is the current Hard-SPL version.
More Notes:
NOTE 1: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter SPL to check version, you need the following key combination: Power Button + Volume Down + Reset Button. means, do a soft reset while holding the "volume down" key and power key on the side of the device. hold these keys until you see a special tricolour screen which is the bootloader mode.
NOTE 2: this is unsigned Hard-SPL. no limitations on flashing ROMs (except of course some Radio roms). also, this has overwrite protection against HTC RUU's overwriting HSPL with a stock one, so if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package is posted on our site. use this relocker *only* if you need to return the phone for warranty, and only use it as last step - after reflashing stock OS and radio. see steps at the end of this post about how to reflash stock SPL.
NOTE 3: anyone having USB problems with the device after it already entered SSPL mode, please copy SSPL-Manual-Rhodium.exe from SSPL-Manual-RhodiumW.zip (available on our site), copy it to the device and run it. then once the screen has gone black, run the Hard-SPL package on the PC and you must select Manual flash option. *important*: make sure that the USB cable is plugged in and device is synced to Windows Mobile even if doing manual method.
NOTE 4: do not use this RUU for anything other than SPL flashing (i.e. hardspl or stock spl restore)!!! nothing other than SPL's made by Olinex team will flash to make SSPL more secure. if you want to flash some other rom, then use shipped RUU or a customRUU if you need to flash cooked ROMs.
NOTE 5: supported OS versions: both 32-bit and 64-bit XP, Vista, Windows 7RC and later. Windows 2000 was untested, and pre-RC win7 (lower than build 7100) is explicitly not supported. also, the program may be unstable or not work on Virtual systems, so it's recommended to try outside Virtual OS software.
Credits:
first, "OliNex" is a team which means: cmonex + Olipro
Olipro -> concept of EXE program that runs on the PC, Hard-SPL concept, server-side license code and maintaining the licenses.
cmonex -> HSPL package on PC, SSPL loader for windows mobile and SSPL binary. Hard-SPL binary. (SSPL loader: partially based on haret and old pof&Olipro jumpspl code),
2. Flashing the ROM
Download Your preferred ROM
Mighty ROMS
Energy ROMS
More Links
http://www.4shared.com/archive/I5UoXF8V/EnergyRHODCDMA29022Sense25Jul0.htm
http://www.4shared.com/archive/3r2Av95q/EnergyRHODCDMA21905Sense25GTXT.htm
I personally prefer Energy ROMS. I have faced a few issues with the mighty ROM.
Flashing Via ActiveSync
1. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your computer
2. REMOVE SIM and microSD CARDS!!
3. Turn phone back on and wait until it syncs with your PC
4. Run the CustomRUU.exe from the Roms Folder (if one isnt included then download it *HERE*)
5. Follow onscreen instructions to set up your New Rom
6. Once phone has gone through the customisation procedure then replace Sim and microSD Cards
7. Turn phone back on and set up as required
OR
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
JOB DONE. Well Done YOU DID IT!!
*DISCLAIMER*
I take no responsibility for any fault or damage caused by any procedures within this guide. No warranties of any kind are given.
I Do Not Accept Donations.
Sharing is Caring.