[Q] How do I flash homebinary.tar files? - Galaxy S I9000 Q&A, Help & Troubleshooting

This may be a dumb question, and I've looked around the forums, but can't find an answer.
I've downloaded KC1 for my Galaxy S, and the file I downloaded is I9000UGKC1_homebinary.tar
I looked inside the tar file and there is cache.rfs, factoryfs.rfs, modem.bin, param.lfs, etc
How do I flash these with Odin?
Thanks

what is the file used for? is it a modem? kernel ?

Well, I downloaded the firmware file for KC1 for the i9000 from samfirmware.com
I was wondering how to upgrade my phone to that, but it only had the one TAR file (and not the PHONE, PDA and MODEM files that other firmwares have).
So i'm not sure how I'm suppose to flash it.

oh!
well you place the file in the PDA tab in odin, and flash away (while repartition is UNCHECKED)

As per the instructions on Samfirmware in regard to flashing with odin .
jje

suppressor said:
oh!
well you place the file in the PDA tab in odin, and flash away (while repartition is UNCHECKED)
Click to expand...
Click to collapse
Thank You! I got stuck on that single file as well.

Related

[Q] How to Flash XXJPY

Hi, I got the JPY ROM from the thread in the general discussion, and any time i have tried to flash it onto my phone, the phone refuses to start properly. It just vibrates a couple of times and black screens.
I am using Odin 1.3 and PIT 512 for this as it says on SamFirmware.com.
Is this the ROM not working properly, or me doing something wrong?
Mate did you click repartition in odin?If you did then you SHOULDNT!!!!
Try to get in to recovery mod with the 3 button combo and make a factory reset if yo had NOT clicked repartition.
In case had HAD clicked repartition in Odin then i guess you ll have to download a foul stock firmware and flash it.Meaning a firmeare that has Modem and CSC files aswell and not only PDA file...
I'm just about to flash XXJPY and I was just wondering, do I have to unroot 'before' flashing the single file (pda) XXJPY or can I leave it as is..?? Does it make any difference..??
Thanks
tackygr said:
Mate did you click repartition in odin?If you did then you SHOULDNT!!!!
Try to get in to recovery mod with the 3 button combo and make a factory reset if yo had NOT clicked repartition.
In case had HAD clicked repartition in Odin then i guess you ll have to download a foul stock firmware and flash it.Meaning a firmeare that has Modem and CSC files aswell and not only PDA file...
Click to expand...
Click to collapse
haha, thanks mate, i forgot to try that, i'll give it a go later.
topcat888 said:
I'm just about to flash XXJPY and I was just wondering, do I have to unroot 'before' flashing the single file (pda) XXJPY or can I leave it as is..?? Does it make any difference..??
Thanks
Click to expand...
Click to collapse
nah you dont need to have it rooted to flash JPY.
I believe the JPY file in the general forum is just an upgrade / high level package which is why you dont tick repartition. Usually look for posts by Richthofen- hes the dude who converts it to mid level packages so you can couple it with a CSC and modem.
hi there same thing happened to me i updated this thru samsung kies im stock at black screen would factory reset make my phone work again? i need help please please please
dopeee said:
nah you dont need to have it rooted to flash JPY.
I believe the JPY file in the general forum is just an upgrade / high level package which is why you dont tick repartition. Usually look for posts by Richthofen- hes the dude who converts it to mid level packages so you can couple it with a CSC and modem.
Click to expand...
Click to collapse
I am already rooted so should I un-root before flashing or just leave it rooted..???
And also have SGS Battery Icon Mod installed, again does this have to be un-installed before flash or not..??
Can someone post a link to the right ROM that I can use to update using ODIN that will not result in existing data lost ? The one that I downloaded is a single tar file (Size - 298,890KB) that contains these files. If this is the right file, do i just specify the tar file in the PDA and uncheck repartition ?
modem.bin
param.lfs
zimage
cache.rfs
factoryfs.rfs

[Q] Flashing Back to stock firmware on my tab

Sorry guys for being a noob.
Story is my tab is rooted and flashed with the OVERCOME RC 2.0 GOLD rom from following alterbridge's thread procedures. Beautiful rom, no complaints.
However the screen has been acting up lately with the finger held down and screen shaking issue.
Ive searched and searched and have concluded its a hardware problem.
I need to flash back to stock for warranty.
For being the noob I am, I've downloaded the stock files....but I don't know how to flash it back.
Attached is a picture of a .zip file of the files inside the zip. Do I use ODIN to flash back? What are the procedures? What file is associated with which box in ODIN? Sorry I just don't have a clue. Or do just throw this into my tab's SD memory and update from CWM recovery mode?...
Do I use superoneclick to unrooted after back to stock rom?
I just don't want to brick my tab...Thanks for any help...
The stock ROM should be a 2.2 FROYO, and the ROM I'm on right now is on Gingerbread...if this makes any difference...
Use this guide first flash with odin it tells you how to flash with odin at the bottom http://forum.xda-developers.com/showthread.php?t=894763
and after flash whatever froyo rom you want make sure you got the one that shipped with your device if its going back for warrenty again flash with odin and your done.
Edit dont forget the thanks button if this hellped you .
Thanks for the link.
So i have the .pit file for the PIT section.
No need for phone and csc section i assume.
But for PDA section i dont have any files available? From my attached picture. i only have a data.tar.gz file. Im not sure what that file is? do i just rename it to .tar??? please help
Sorry not sure on them files i think you can use heidmal with those files do a search on here for that
Anyone???
What do I use? ODIN? HEIMDALL? I need help please.
From overcome gold you will have to re-stock to froyo. Which means a repartiton with pit file + phone + modem files. You will need odin for this.
I would suggest flash back to a safe froyo rom first - as per jutleys link above. Then flash back to your original firmware version.
From the pic above looks like you have unzipped the full.zip. For Odin You need the full zip in the pda section, modem zip in the modem and the pit file in the pit section. Download full zips from roto's link above.
Then check out roto backup thread (shows how to restore using heimdall / odin). As i havent flashed back to my original firmware yet, someone else could advise better. I am assuming for stock purposes you need to put the original stock firmware zip into pda section of odin and leave everything blank and then flash away.
Cheers
ezynow said:
From overcome gold you will have to re-stock to froyo. Which means a repartiton with pit file + phone + modem files. You will need odin for this.
I would suggest flash back to a safe froyo rom first - as per jutleys link above. Then flash back to your original firmware version.
From the pic above looks like you have unzipped the full.zip. For Odin You need the full zip in the pda section, modem zip in the modem and the pit file in the pit section. Download full zips from link above.
Then check out roto backup thread (shows how to restore using heimdall / odin). As i havent flashed back to my original firmware yet, someone else could advise better. I am assuming for stock purposes you need to put the full firmware zip into pda section of odin and leave everything blank and then flash away.
Cheers
Click to expand...
Click to collapse
Thank you for your response. I'll work on getting back safely to a froyo rom.
As for the picture, it is a pic of the content inside the full zip already. Should i unzip and enter modem and pit according? But what goes into the pda section?
chris28j said:
Thank you for your response. I'll work on getting back safely to a froyo rom.
As for the picture, it is a pic of the content inside the full zip already. Should i unzip and enter modem and pit according? But what goes into the pda section?
Click to expand...
Click to collapse
That pic is from a firmware from samfirmware? It has the bootloaders in it so be very careful as flashing bootloaders can cause bricks or be protected ones. As i said before, i think you flash the full zip in the pda section and leave the rest blank i.e no need to unzip.
But do so only after flashing using roto safe froyo rom.
As for the files above, It might be wise to take out the bootloaders then rezip & flash but i would wait on someone with a bit more knowledge just to confirm this.
As long as they are the original files for your firmware, you should be ok.
Thanks for your help ezynow.
UPDATE: I've successfully downgraded from Overcome Gingerbread to Overcome Froyo now.
Now it's just a matter of getting my head wrapped around this stock ROM right. The order, and where the files should go.
Anyone else would like to share their insight? This is the file I downloaded, and this is how it is presented to me. I just need someone to help me sort out what is what.
Thanks.
UPDATE #2: Tried re-zipping and converting to tar file. ODIN failed. Re-zipped into tar again without the data.tar.gz file because I don't know what it is, and failed again.
I don't know what to do anymore. How do I get this to work?
bump
anyone?
UPDATE #3: Tried loading the whole .zip file from CWM. No luck.
Who's your service provider?
I sugest look for another stock rom here that is in the correct format i am sure i seen a post showing all stock roms somewhere use odin
Link deleted. It mentions to use pit file + full zip in pda section . Then says out of date.
Also did you check rotobbackup method thread - use heimdall and flash individual files from your extraced zip files. Assuming you can avoid flashing bootloaders you should only be a soft-brick if anything goes wrong and download mode still available.
Forget about using cwm for anything stock related.
Sum1 who has reverted back to stock surely can help out here!
p.s what was your original firmware version?
I have succesfuly downgraded from gb overcome gold to arabic froyo using the file from samfirmware. First try resulted in stuck at samsung logo but I was expecting that due to the ext4 partition. A cache wipe and factory reset in recovery solved that problem. Also I observed when going to recovery that there were errors in red that are coming out complaining of access problem to certain files. Since I am able to boot I then proceded to format the internal sd. After that I again flashed using the same arabic fw. No problems so far even kies sees my fw as the latest.
Here is the procedure I followed-change the files according to your fw version
noxxious said:
Flash with Odin3 v1.7
1. Download P1000DXKM3 from here. P1000DXKM3
1. Backup your data.
2. Extract the firmware files from the P1000DXKM3.7z file.
3. select P1_add_hidden.pit for .pit file.
4. check repartition.
5. select AP_P1000DXKM3-REV03-ALL-CL874291.tar.md5 for PDA.
6. select CP_MODEM_P1000DXKM1_REV_00_CL873880.tar.md5 for PHONE.
7. select CSC_P1000OLBKM2-MULTI-CL878295.tar.md5 for CSC.
8. Flash your tab and wait for it to restart.
9. Welcome back to stock.
extra steps
10. Root by using SuperOneClick v1.9.1 by CLShortFuse.
11. Unsign Bootloaders by using this SGT-Bootloader-Patch by chainfire and rotohammer.
Click to expand...
Click to collapse
Sent from my GT-P1000 using Tapatalk
Thanks a lot for the help guys.
I will try going to another stock firmware later this afternoon.
However, the firmware I really need is P1000MUGJJ7 (Bell's stock firmware).
The files I have in hand are apparently the files for this firmware, but how to restore it, I have zero clue. These we're sent to me by a member on this forum.
I think the member said that these were created from roto backup.
I have looked everywhere else for this firmware version but it's NOWHERE. Neither does samfirmware.com
So to sum it up, pretty much these are my only sources to play with, and just gotta make it work...
Please help and thanks again.
anyone?
bump
What are the contents of this bell fw? have you tried opening the file?
bongski55 said:
What are the contents of this bell fw? have you tried opening the file?
Click to expand...
Click to collapse
Please refer to the attached picture.
It's a pic of the contents inside the .zip file I was given.
Now I just need a solution as to HOW to use them.
Only the pit.pit file can be used.extract it and in odin load it under pit. then under pda load the whole tar file. then check repartition ,reboot and time.....start...
bongski55 said:
Only the pit.pit file can be used.extract it and in odin load it under pit. then under pda load the whole tar file. then check repartition ,reboot and time.....start...
Click to expand...
Click to collapse
OK. So you are suggesting I take out pit file then CONVERT in someway the whole .zip file into .tar file for the PDA section, am I correct?
Now, I need a proper way to convert this file because I tried this using a converter I downloaded online. And after the conversion, the .tar files was double the size (over 400mb, original ~200mb). And flashing through ODIN using this new file didn't work. So what's the proper way to convert?

What to flash a semi bricked phone with?

Hi I'm new to this so bare with me.
My Galaxy S has been playing up recently and when I try to switch it on it goes to the first Samsung Galaxy S gt-i9000 startup screen, the screen then goes dark then the same screen reappears. this happens until i remove the battery.
Odin and having to manually flash my phone is all new to me so I would like some advice as to what to flash my phone with to try and get it up and running again.
many thanks.
Odin
Sent from my sense uid SGH-I997 using XDA App
Put the pda firmware file in the pda slot. phone file in the phone slot . if there is a pit file put it in the pit slot. Then hit flash
Sent from my SGH-I997 using XDA App
thanks. which firmware files and pit files are best served to simply get my phone back up and running again?
impatientlime said:
thanks. which firmware files and pit files are best served to simply get my phone back up and running again?
Click to expand...
Click to collapse
my personal fav to get out of any such troubles
http://www.darkyrom.com/community/index.php?threads/odin-jvu-re-gt-i9000.6558/
many thanks.
on that link, it tells me to 'Put PDA.tar it into PDA', is this a file that should of been included in the download pack along with the pit file. because i cannot locate it anywhere?
also in odin, do i need to tick the PDA box when i upload a file into it?
thanks.
impatientlime said:
many thanks.
on that link, it tells me to 'Put PDA.tar it into PDA', is this a file that should of been included in the download pack along with the pit file. because i cannot locate it anywhere?
also in odin, do i need to tick the PDA box when i upload a file into it?
thanks.
Click to expand...
Click to collapse
the package you downloaded.. can you tell me what are the files that are included in it..
When you browse the pda file in odin, it'll get checked by itself..
i have...
s1_odin_20100512.pit
boot.bin
cache.rfs
dbdata.rfs
factoryfs.rfs
modem.bin
param.lfs
sbl.bin
zimage
impatientlime said:
i have...
s1_odin_20100512.pit
boot.bin
cache.rfs
dbdata.rfs
factoryfs.rfs
modem.bin
param.lfs
sbl.bin
zimage
Click to expand...
Click to collapse
the link I gave, downloads the zip file .. JVU-RE.zip... in it you found all these?
from what I can understand you should have found two files..
s1_odin_20100512.pit
and the other one another compressed file which would comprise of the rest of files you mentioned..
along with odin files I guess
is that right?
haha, apologies i've worked it out. stupidity on my behalf.
i have flashed my phone, however it has made no difference. still facing the same problem. think i've got to face up to the fact that my phone is finished.
impatientlime said:
haha, apologies i've worked it out. stupidity on my behalf.
i have flashed my phone, however it has made no difference. still facing the same problem. think i've got to face up to the fact that my phone is finished.
Click to expand...
Click to collapse
even after flashing this you are not able to get past the GT-I9000 screen?
the flashing was successful right?
yes the flash was successful but i still cannot get past the i9000 screen.
impatientlime said:
yes the flash was successful but i still cannot get past the i9000 screen.
Click to expand...
Click to collapse
that's really weird then .. try flashing stock samsung firmware ..
you can download from this link
http://www.sammobile.com/firmware/?page=3&t=1&o=1&m=GT-I9000&r=1
would suggest downloading the one for your region and flashing in same way you flashed earlier.. this would give an unrooted stock rom on your SGS .. if this also isn't successful well then you should take it to service center.

[Q] How to downgrade from CM10 to stock GB?

Long story but I need to downgrade my i9000 from CM10 (currently on c-rom bean v2.3) back to stock 2.3.6 and couldnt find anything specific to the i9000 on to how to do it. Can I just get the stock firmware (ie PDA, CSC, Phone) and then flash through Odin? But I read on XDA (http://forum.xda-developers.com/showthread.php?t=1729458) that I may also need PIT and Bootloader? If so, where can I download these files??? Any help greatly appreciated!!!!
blion said:
Long story but I need to downgrade my i9000 from CM10 (currently on c-rom bean v2.3) back to stock 2.3.6 and couldnt find anything specific to the i9000 on to how to do it. Can I just get the stock firmware (ie PDA, CSC, Phone) and then flash through Odin? But I read on XDA (http://forum.xda-developers.com/showthread.php?t=1729458) that I may also need PIT and Bootloader? If so, where can I download these files??? Any help greatly appreciated!!!!
Click to expand...
Click to collapse
You have to download any 3 files stock ROM (I suggest you JVS, as JW versions can damage your IMEI), then select PDA, CSC and Phone
in ODIN. You don't have to have bootloader, as it is already in PDA, and yes, you have to have PIT file, it is usually within archive with ROM.
Just flash it and you're done. For download go to this thread: http://forum.xda-developers.com/showthread.php?t=1837223 and you'll find
there any ROM you want. Hope it will help you.
--
Leszek
twinsen.net said:
You have to download any 3 files stock ROM (I suggest you JVS, as JW versions can damage your IMEI), then select PDA, CSC and Phone
in ODIN. You don't have to have bootloader, as it is already in PDA, and yes, you have to have PIT file, it is usually within archive with ROM.
Just flash it and you're done. For download go to this thread: http://forum.xda-developers.com/showthread.php?t=1837223 and you'll find
there any ROM you want. Hope it will help you.
--
Leszek
Click to expand...
Click to collapse
Thanks for your prompt response. I am looking to go back to stock GB and last time I downloaded them from here (http://forum.xda-developers.com/showthread.php?t=1102881&page=1). I chose XWJW8/XWJW1/VAUJV9/Sbl (CSC: VAU (Vodafone)) as I live in Australia and my provider is Vodafone. But how do I extract the PIT file??
Also out of curiosity, what if I chose the stock rom of another network provider? Does it make a difference??
blion said:
But how do I extract the PIT file??
Also out of curiosity, what if I chose the stock rom of another network provider? Does it make a difference??
Click to expand...
Click to collapse
you cannot extract a PIT File, you can download a 512 PIT file from My Android Collections
If you use telstra , it will not work for vodafone and vice versa as they are branded
(Do remember to backup your contacts, data, images etc and also your EFS folder before flashing a ROM and make sure you have more than 50% battery charge before you attempt any sort of flashing.)
xsenman said:
you cannot extract a PIT File, you can download a 512 PIT file from My Android Collections
If you use telstra , it will not work for vodafone and vice versa as they are branded
(Do remember to backup your contacts, data, images etc and also your EFS folder before flashing a ROM and make sure you have more than 50% battery charge before you attempt any sort of flashing.)
Click to expand...
Click to collapse
Ok. So I take the 512 pit file from your link and also the official GB firmware from Ramad's thread. Then flash using Odin with only PIT, PDA, Phone and CSC. Also "re-partition", "Auto reboot" and "F Reset Time" needs to be ticked. Sorry about being so padantic but just wanted to make sure I get the steps right the first time. Thanks!!!
blion said:
Ok. So I take the 512 pit file from your link and also the official GB firmware from Ramad's thread. Then flash using Odin with only PIT, PDA, Phone and CSC. Also "re-partition", "Auto reboot" and "F Reset Time" needs to be ticked. Sorry about being so padantic but just wanted to make sure I get the steps right the first time. Thanks!!!
Click to expand...
Click to collapse
yup, that should do it mate.

[Q] Going back to stock, confused...

Hi
I am having a little bit of trouble going back to stock. I currently run the latest cm10 nightly, which repartitions your phone, right? So i want to go back to stock, but am confused. I have a 803 pit file which i believe i need to flash. Now the firmware package i have (from sammobile.com, correct one for my region) is all one tar file. Does not contain files that odin can flash, so in which one (pda, boot, modem etc.) do i need to put that file? It contains a load of .bin and .rfs files. Also, reading this guide: http://forum.xda-developers.com/showthread.php?p=7152078#post7152078 it tells me not to flash the pit with the one package file i have, so what is the exact procedure?
Thanks in adavnce!
The package you have is the PDA if is only one don't insert a pit and don't tick repartition,only put the file In the pda
Inviato dal mio GT-I9000 con Tapatalk 2
race55 said:
Hi
I am having a little bit of trouble going back to stock. I currently run the latest cm10 nightly, which repartitions your phone, right? So i want to go back to stock, but am confused. I have a 803 pit file which i believe i need to flash. Now the firmware package i have (from sammobile.com, correct one for my region) is all one tar file. Does not contain files that odin can flash, so in which one (pda, boot, modem etc.) do i need to put that file? It contains a load of .bin and .rfs files. Also, reading this guide: http://forum.xda-developers.com/showthread.php?p=7152078#post7152078 it tells me not to flash the pit with the one package file i have, so what is the exact procedure?
Thanks in adavnce!
Click to expand...
Click to collapse
If you have one file .tar choose it on bootloader and select auto reboot and f.reset time.:good:

Categories

Resources