Related
Ok here goes... This is my first thread post here but I am in serious need of help.
I have searched and searched the forums for a hopeful answer but I have found it difficult to find the answer I seek.
So here is the story:
Bought a GT second hand from Akihabara in Japan which was locked to NTT DoCoMo. I was using it as a WIFI only Tab and all was wonderful till my IT brain decided it could be better and I began to tinker.
I had been looking around for a way to make my Australian Virgin Mobile SIM to work on the tab and found a lot of good answers but nothing that would make it work.
I then had the brilliant idea to change the firmware with a European firmware so I could get all the features enabled from a fresh start. Which is where it all went wrong.
I first tried to flash the tab using Odin 1.7 with the P1000XXJK5 euro firmware from samfirmware.com
This failed and left my tab with the picture of a phone and a pc with a dotted line and in between them an exclamation point in a triangle.
After a lot of fiddling (I dont remember what I did but I managed to get rid of that screen had something to do with retrying the flash and it was very late last night at this point) I managed to try again but Odin just kept failing on running the updated firmware.
I then decided that it would be a good idea to run the Rotohammer firmware by following the instructions on this thread:
http://forum.xda-developers.com/showthread.php?t=895827&highlight=sc-01c
This is where I once again received errors from Odin and now my tab is somewhat bricked.
I tried reflashing but same errors every time. (I currently dont have the errors from Odin but I will update my post when I get home)
I can still get to the downloading screen (Yellow triangle with the Android digging) so I am hopeful all is not lost.
So now you have heard my sob story I will ask two questions....
1. Has anyone actually successfully flashed a Japanese model Tab?
2. My only thought/hope at the moment can anyone direct me to an original NTT DoCoMo firmware so I can at least go back to having WIFI only Tab?
Thanks in advance if you can help
Alex
Yes , i suggest you to wait until you get a right firmware for it !
That would probably work if the partitions are a match !
What is this model called btw ?
"NTT DoCoMo Japanese Tab" or there is any model ? such as M180 for korean , P1000 , P100 Sprint , I800 Verizon , etc..
Br
Oz
I am searching the an original NTT DoCoMo firmware.
Electroboy said:
Yes , i suggest you to wait until you get a right firmware for it !
That would probably work if the partitions are a match !
What is this model called btw ?
"NTT DoCoMo Japanese Tab" or there is any model ? such as M180 for korean , P1000 , P100 Sprint , I800 Verizon , etc..
Br
Oz
Click to expand...
Click to collapse
Oz the model is SC-01C it has a build date of 2010/12
I was thinking considering I can get into the build/download screen maybe trying an emergency firmware recovery using Kies.
Hi,
I'm a fellow SC01 owner. You can get a backup of the stock firmware here: http://www.megaupload.com/?d=OJAK2UZF
Firmware code is SC01COMJK2
I believe there are newer firmwares (which I haven't installed as some of them contain a new bootloader that only allows for signed firmwares, same as the international units) that I have seen mentioned on various Japanese blogs. Let me know if you want me to try to hunt any down for you.
As for my SC01, I installed the custom kernel by koxudaxi and it's working great. Mind you, I've only changed to this kernel and apart from that am running the stock OS. I got his kernel here which can overclock to 1.4GHz: http://koxudaxi.sakura.ne.jp/
The kernel I installed via Heindall is zImage_ntt_2. It looks like he's built a newer version though, I might check that out. I think what you might want to do, is in download mode try to restore the above backup to your unit. Look up the Roto Backup thread to see how to do this. Hopefully since you can get download mode, all is not lost. I personally think it's quite crummy that there are different hardware versions like this which aren't interchangeable though >_<
I'm going to give the original firmware a go today at lunch time and I will let you know how I go. Thanks anyways for the link if all goes well I'll look at possibly trying the the koxudaxi kernel.
UPDATE: Well I'm not having luck getting the firmware to flash to my tab I keep getting "Failed to retrieve config Descriptor" when trying to flash. I will keep plugging away.
UPDATE: Still getting the same problems using heimdall to flash the tab. Any suggestions as to what I could do next?
Recovering a Docomo Tab
I'm currently running Overcome v1.1.3 ROM and richardtrip's V15 kernel on my SC-01C.
acont said:
UPDATE: Well I'm not having luck getting the firmware to flash to my tab I keep getting "Failed to retrieve config Descriptor" when trying to flash. I will keep plugging away.
Click to expand...
Click to collapse
You're getting this error from Heimdall, right? Have you tried Odin 1.7?
Here's how I recovered my Tab using Odin:
1. Following the instructions in http://forum.xda-developers.com/showthread.php?t=895827, specify the P1_add_hidden.pit in the PIT button and select Re-Partition.
2. Specify the stock Docomo ROM when pressing the PDA button.
3. Ignore the Phone and CSC buttons, as the stock ROM already contain these items.
You should be able to restore your Tab to stock settings using this procedure.
If this doesn't work, you might want to check if the USB connection to your PC is ok, and if everything necessary to run Odin is installed on your PC.
Bugger!
Well thanks for your help all of you but I think I have just made matters worse.
Last night I had success in flashing the original docomo firmware provided to me by zetsurin but I think I shouldn't have included the boot images.
Unfortunately I think it is completely bricked now it now wont turn on and when plugged into power (thinking that the battery had died) it just comes up with a white screen.
I can't boot into download mode and I can hold down the power button till I turn blue in the face... So as Bones would say "It's dead Jim"
Unless any of you have anything else I could try as a last ditch shot I might just have to ship it back to Japan and get them to fix it or maybe try Samsung here in Oz.
Serves me right
Thanks again.
acont said:
Last night I had success in flashing the original docomo firmware provided to me by zetsurin but I think I shouldn't have included the boot images.
Click to expand...
Click to collapse
What exactly happened?
The SC01COMJK2 firmware does not contain protected bootloaders, by the way.
acont said:
Unfortunately I think it is completely bricked now it now wont turn on and when plugged into power (thinking that the battery had died) it just comes up with a white screen.
Click to expand...
Click to collapse
I've heard about this happening when the battery runs out. Try connecting the Tab to your PC (not your AC adapter) and let it trickle-charge for an hour or so. If successful, you should see the download screen.
fury1sog unfortunately that didnt work
spoke to the samsung repairers here in Aus and they said they can take a look at it for me hopefully bring life back into my unit and then I will never touch it again
Any thoughts?
Hopefully this post is still being looked at but has anyone got any ideas as to what I could do before I fork out $374 to my tab repaired by Samsung Australia?
According to the repair guys its a faulty board (not an idiot that tried to flash it) and needs to be replaced. Not sure if this is worth my trouble considering I could buy a brand new tab for $599.
There is a positive out of this, the MB will be an Australian MB and I will have a working "Australian" tab instead of the Japanese version.
Considering the unfortunate tragedy in Japan I am not sure I should try and get my friend in Japan to fix it for me.
Thoughts anyone?
I know someone who can unlock it, I have mine unlocked by them.
I was afraid of flashing it myself so I paid to have it unlocked, cost was $20.
I think you better go for the MB replacement, it's cheaper.
For what it's worth, I went to reset my tab to factory using a rotohammer backup I made when I first bought it, and got stuck in a boot loop. So I then used ODIN. Still got a boot loop. Then I tried ODIN repartition... it hung for hours. Knowing the thing was likely bricked I pulled the plug and now I am in the situation as you: I have a crappy icon of a phone + an exclamation + computer image. Dead.
I think the best thing I can do for this junk is to toss it unceremoniously in the bin. Fortunately I also have an iPad which has resumed full-time service.
EDIT: Some signs of hope in here: http://forum.xda-developers.com/showthread.php?t=903257
Try "heimdall close-pc-screen" to see if your tab can get kicked back into the boot loop at least. Mine has failed a repartition, but I can still get it into the boot loop, which is a start. Will experiment over the weekend.
EDIT 2: Well my tab is back up and runing. I reflashed my original roto backup using ODIN with repartition on, then I went into recovery and did a factory restore. Back up like stock now. I think I'm going to sell it though, since it's been badly dis-owned by Samsung.
zetsurin said:
Hi,
I'm a fellow SC01 owner. You can get a backup of the stock firmware here: http://www.megaupload.com/?d=OJAK2UZF
Firmware code is SC01COMJK2
I believe there are newer firmwares (which I haven't installed as some of them contain a new bootloader that only allows for signed firmwares, same as the international units) that I have seen mentioned on various Japanese blogs. Let me know if you want me to try to hunt any down for you.
As for my SC01, I installed the custom kernel by koxudaxi and it's working great. Mind you, I've only changed to this kernel and apart from that am running the stock OS. I got his kernel here which can overclock to 1.4GHz: http://koxudaxi.sakura.ne.jp/
The kernel I installed via Heindall is zImage_ntt_2. It looks like he's built a newer version though, I might check that out. I think what you might want to do, is in download mode try to restore the above backup to your unit. Look up the Roto Backup thread to see how to do this. Hopefully since you can get download mode, all is not lost. I personally think it's quite crummy that there are different hardware versions like this which aren't interchangeable though >_<
Click to expand...
Click to collapse
hi zetsurin!
thanks for teaching me how to unlock the tab.
problem now is, im not able to successfully flash any rom. keeps saying write fail, using odin.
stuck at docomo logo when rebooted.
need help.
also used heimdall. starts downloading. but stuck almost at the end of the tab's progress bar.
argh...
me too ! samsung galaxy tab m180 Korean .... huhu
What ROM is best for a SC-01C?
Hi Guys
I picked up a 2nd hand SC-01C from Yahoo Auction, and am wondering what the best ROM to use with it is...
Looks like this guy has got an Overcome ROM on it OK, (http://chaki-ramone.blogspot.com/2011/06/galaxytabsc-01cgingerbreadromovercome.html), so I wonder if the latest version (http://forum.xda-developers.com/showthread.php?t=1205990) will work OK - anyone tried? (is the SC-01C a GSM-based model??)
I'm not going to use a SIM with it, so I'm not bothered about unlocking - but just want it rooted & want a good balance between speed & battery life. If you were going from scratch with an SC-01C, what would you do? Any suggestions greatfully received!
Thanks in advance?
PS - I'm an iPhone / iPad / Ideos 8150 / Notion Ink Adam owner, all jailbroken / rooted. So I'm not scared about rooting per-se, just worried about trying something that will not work because of anything docomo has done to the Tab!
Acont you could be coma bricked try pluginging it into THE MAINS for at least 4 hours if nothing come up your hard bricked.
Sent from my GT-P1000 using XDA Premium App
zetsurin said:
For what it's worth, I went to reset my tab to factory using a rotohammer backup I made when I first bought it, and got stuck in a boot loop. So I then used ODIN. Still got a boot loop. Then I tried ODIN repartition... it hung for hours. Knowing the thing was likely bricked I pulled the plug and now I am in the situation as you: I have a crappy icon of a phone + an exclamation + computer image. Dead.
I think the best thing I can do for this junk is to toss it unceremoniously in the bin. Fortunately I also have an iPad which has resumed full-time service.
EDIT: Some signs of hope in here: http://forum.xda-developers.com/showthread.php?t=903257
Try "heimdall close-pc-screen" to see if your tab can get kicked back into the boot loop at least. Mine has failed a repartition, but I can still get it into the boot loop, which is a start. Will experiment over the weekend.
EDIT 2: Well my tab is back up and runing. I reflashed my original roto backup using ODIN with repartition on, then I went into recovery and did a factory restore. Back up like stock now. I think I'm going to sell it though, since it's been badly dis-owned by Samsung.
Click to expand...
Click to collapse
Can anyone pls help,, my galaxy tab 7inch gt-p1000r is stuck on phone+pc logo, can't go to download mode, can't go to recovery mode,, can't do anything,, pls someone help me,, I am desperate..
huylang280285 said:
me too ! samsung galaxy tab m180 Korean .... huhu
Click to expand...
Click to collapse
unbricking M180 is done long time ago
Here is a video for you
http://www.ort-jtag.com/blog/?e=15
udhtari said:
Can anyone pls help,, my galaxy tab 7inch gt-p1000r is stuck on phone+pc logo, can't go to download mode, can't go to recovery mode,, can't do anything,, pls someone help me,, I am desperate..
Click to expand...
Click to collapse
What about this P1000R , what is special or different ?
I know P1000L was for south american edition !
lemmy_0 said:
hi zetsurin!
thanks for teaching me how to unlock the tab.
problem now is, im not able to successfully flash any rom. keeps saying write fail, using odin.
stuck at docomo logo when rebooted.
need help.
Click to expand...
Click to collapse
Docomo solution is very soon !
That TAB need JTAGging thats the only way ..
I have the good and dead device in hand , we will release for ORT-JTAG probably this week ..
Best Regards
Oz.
I have searched every post and followed every guide. And flashed pretty well every CDMA firmware I can find with no luck. Ok here is what I have. Tab would do nothing but the Samsung logo and then just a black screen with a vibration every few seconds. I finally got past that but still pretty screwed. I managed to flash the rom Samsung Galaxy Cubed with his old kernal. No the tab will load up, but a list of problems:
1. No verizon boot animation(no biggie)
2.No clockwork mod or recovery(thru the market app or power and volume)
when pushing the power and volume up I get a screen that stats power reset unknown command(something to that effect)
when using the market app I get suscess in bootstrap but when I push the recovery I go into bootloop
3.The tab will not leave airplane mode but will connect to wi-fi.
4.Under the system info for hardware and build number it stats unknown
I think that is most of it. I have a lot of experience with CMW, Sbf, flashing roms and all that good stuff with a droid x, but I am pretty noob with the whole tab. I try my best to support devolpers with buying apps and donations. So if anyone is willing to help a noob out I am more than happy to pay or help out in return in anyway possible. Thanks in advance.
Sounds like you need a new modem. see the modem thread.
Hi All,
Australin Optus GT-I9305 (4G/LTE Ver).
Android 4.1.2
Download mode: Binary dowload 3 - Current binary Official - System status Official
I tried to root my SGS3 today with Odin however I used the wrong root from my old Note 2 which caused the screen to do weird things and then the screen would not boot up or respond. I have reinstalled the stock software on it with Odin and now the phone starts up but still does not respond to my touch's.
I can boot into recovery and download mode no problem. I have cleared the cache and performed a factory reset still no response from screen. I am stuck in the first set up screen atm the menu key, back & home key all make sounds when I touch them.
If I unroot the phone will it fix this issue? if so how?
Is the phone gone/dead/unfixable?
Or can I use USB OTG to control the phone so I can use triangle away and return for warranty?
I also think USB debugging is off as well as I cannot get into the phone.
Any help will be really appreciated thanks guys.
Although extremely similar in hardware the screen's digitalizers are different causing issues like this instead of a plain brick that you would get if you tried a I9300 firmware. Try using Samsung Emergency Restore on Kies.
If that doesn't work then you may have to send it into a repair center as you could have, put bluntly, ****ed it.
Sent from my GT-I9305 using xda premium
I've read of several cases where people have used Roms or recoveries intended for the Note 2 on their S3 and it literally fries the screen.
It allows too much current through or something like that.
I think you will need to get a new screen mate.
We have a AT&T LTE 8.9 which I now deduce is a P7320 model. A year back when I got the 8.9, I rooted it, CWMed and installed a a AOKP ROM and it has been running great since. However, last week I swapped it for another device with my brother who decided I should put it back to the stock ROM so that he could ebay it.
Well with all the timeliness and hectic mode of the festive season, I failed to research thoroughly and flashed it a stock P7300/P7310 ROM. Which rendered it completely dead. It would not respond to anything, power/vol+, power/vol-, power/both vols, usb to pc, usb to wall with no charging icon e.g. Odin doesn't even see it. The only sign of life if that, is that it shows up as an error with QHUSUB_DLOAD in device manager.
Right now, I have the power button taped down to see if I can get anywhere draining the battery. You would think that Odin should at least see it? Is this the end of my tab?
bdbx18 said:
We have a AT&T LTE 8.9 which I now deduce is a P7320 model. A year back when I got the 8.9, I rooted it, CWMed and installed a a AOKP ROM and it has been running great since. However, last week I swapped it for another device with my brother who decided I should put it back to the stock ROM so that he could ebay it.
Well with all the timeliness and hectic mode of the festive season, I failed to research thoroughly and flashed it a stock P7300/P7310 ROM. Which rendered it completely dead. It would not respond to anything, power/vol+, power/vol-, power/both vols, usb to pc, usb to wall with no charging icon e.g. Odin doesn't even see it. The only sign of life if that, is that it shows up as an error with QHUSUB_DLOAD in device manager.
Right now, I have the power button taped down to see if I can get anywhere draining the battery. You would think that Odin should at least see it? Is this the end of my tab?
Click to expand...
Click to collapse
First of all, is your tab booting to AOSP now ??
if not can you see the [Samsung Galaxy Tab Logo], and after what did that happened (is it after you flashed a P7300 Stock ROM??)??
have you ever flashed stock ROM through odin before??
can you at least enter the recovery (CWM)??? cuz that would make things easier
we should know these things before we can help
omarainea said:
First of all, is your tab booting to AOSP now ??
if not can you see the [Samsung Galaxy Tab Logo], and after what did that happened (is it after you flashed a P7300 Stock ROM??)??
have you ever flashed stock ROM through odin before??
can you at least enter the recovery (CWM)??? cuz that would make things easier
we should know these things before we can help
Click to expand...
Click to collapse
The tab is non-responsive to *anything*. It won't boot, tethered or not, after the incorrect stock rom flash. I cannot get into recovery and odin does not see it. I have had a blank screen since.
Yes, I am somewhat familiar with odin/fastload/adb and various other tools for my android phones. Prior to this deadly flash, I had used odin to install cwm and a ROM on it. However, at this point, odin cannot see the tab either.
bdbx18 said:
The tab is non-responsive to *anything*. It won't boot, tethered or not, after the incorrect stock rom flash. I cannot get into recovery and odin does not see it. I have had a blank screen since.
Yes, I am somewhat familiar with odin/fastload/adb and various other tools for my android phones. Prior to this deadly flash, I had used odin to install cwm and a ROM on it. However, at this point, odin cannot see the tab either.
Click to expand...
Click to collapse
I assume that the problem is caused from the bootloader incompatibility
so you're saying that you can't enter the download mode or CWM
and your computer can't recognize your tab through adb connection ether
if this is exactly the case, then I don't think anyone can help you
maybe you should try to take your tab to any close samsung branch
Good luck
omarainea said:
I assume that the problem is caused from the bootloader incompatibility
so you're saying that you can't enter the download mode or CWM
and your computer can't recognize your tab through adb connection ether
if this is exactly the case, then I don't think anyone can help you
maybe you should try to take your tab to any close samsung branch
Good luck
Click to expand...
Click to collapse
You can get JTAG for about $40 so not that bad:
http://www.youtube.com/watch?v=BgL5vWRwh5k#t=22
http://mobiletechvideos.mybigcommerce.com/samsung-galaxy-tab-8-9-jtag-brick-repair/
Hi All.
I am looking for help and advice with regards to getting my wife's Samsung Galaxy S3 Mini GT-I8190N working again.
My wife has been having issues with this phone restarting it's self at random on and off for the last few months, but as the phone is always in use/needed, I have been unable to have a look for the cause of the problem.
A few weeks ago the phone powered down, and would not switch back or, it would also not charge.
After removing the battery and having a closer look it seems that the battery has swollen and is no longer flat so a new replacement battery was ordered.
The new replacement battery was fitted and the phone was put on charge, the phone displayed that is was now charging, I thought all was good and just left the phone to charge.
Some time later on I tried to power on the phone, but am just greeted by "Samsung Galaxy S3 Mini GT-I8190N" logo and then the phone just restarts again, and keeps on doing this.
The phone is 100% stock, it has not been unlocked or re-flashed.
The phone is on contract from Tesco Mobile, but my wife has been told by Tesco that the warranty has expired.
From searching on the forum it seems that it is quite common for Samsung phones to get stuck in this kind of boot loop.
So far it seems that there are two possible ways to fix the current issue.
1 - Power off the phone and go into boot-loader and do a factory reset.
or
2 - Re-flash the stock rom.
So I thought I would 1st try the factory reset.
So I removed and replaced the battery, Held down "Volume Up, Home, Power", I am then greeted by "Samsung Galaxy S3 Mini GT-I8190N" logo and the phone just sits there.
So it now looks like the only other option is to re-flash the phone with the stock rom.
But how do I find out what stock rom that I need for this phone, as I am unable to get into the bootloader to run any ADB or FastBoot commands.
Any help would be much appreciated.
Thanks for your time.
Best Regards.
MadProfessor2002 said:
Hi All.
I am looking for help and advice with regards to getting my wife's Samsung Galaxy S3 Mini GT-I8190N working again.
My wife has been having issues with this phone restarting it's self at random on and off for the last few months, but as the phone is always in use/needed, I have been unable to have a look for the cause of the problem.
A few weeks ago the phone powered down, and would not switch back or, it would also not charge.
After removing the battery and having a closer look it seems that the battery has swollen and is no longer flat so a new replacement battery was ordered.
The new replacement battery was fitted and the phone was put on charge, the phone displayed that is was now charging, I thought all was good and just left the phone to charge.
Some time later on I tried to power on the phone, but am just greeted by "Samsung Galaxy S3 Mini GT-I8190N" logo and then the phone just restarts again, and keeps on doing this.
The phone is 100% stock, it has not been unlocked or re-flashed.
The phone is on contract from Tesco Mobile, but my wife has been told by Tesco that the warranty has expired.
From searching on the forum it seems that it is quite common for Samsung phones to get stuck in this kind of boot loop.
So far it seems that there are two possible ways to fix the current issue.
1 - Power off the phone and go into boot-loader and do a factory reset.
or
2 - Re-flash the stock rom.
So I thought I would 1st try the factory reset.
So I removed and replaced the battery, Held down "Volume Up, Home, Power", I am then greeted by "Samsung Galaxy S3 Mini GT-I8190N" logo and the phone just sits there.
So it now looks like the only other option is to re-flash the phone with the stock rom.
But how do I find out what stock rom that I need for this phone, as I am unable to get into the bootloader to run any ADB or FastBoot commands.
Any help would be much appreciated.
Thanks for your time.
Best Regards.
Click to expand...
Click to collapse
Download the stock firmware you prefer from here: http://www.tsar3000.com/Joomla/inde...iii-mini-firmwares&catid=55:samsung&Itemid=82
Then follow this guide to install it: http://forum.xda-developers.com/showthread.php?t=2429169
Riky720: Thank you for your reply, and the links.
I have already been reading the following guides
[GUIDE] Stock Rom - All S3 Mini
and
[GUIDE] Unroot / Unbrick, Flash official stock firmware on Galaxy SIII Mini GT-I8190
Can you please advice how I can find out what is the correct firmware / stock rom to download, as the phone will not boot, and I am unable to use ADB or Fastboot to pull any information from the phone.
As said before my wife got the phone from Tesco Mobile on contract, and from my understanding is that Tesco Mobile uses the O2 Network.
Looking at the list of firmware's I can't not see any listed as Tesco Mobile.
Thanks again for your time.
Best Regards.
I am still having issues with this phone, and I have been unable to progress forward.
I did start this post: Samsung Galaxy S3 Mini GT-I8190N - Re-flashing stock rom, to try and locate the stock firmware (rom) so that I could re-flash it.
From my other post I have been able to locate the following firmware (roms) for the phone.
I8190NXXAMJ2_I8190NBTUAMJ1_BTU.zip
I8190NXXAMG1_I8190NOXXAMG1_BTU.zip
I8190NXXALL6_I8190NOXXALL3_BTU.zip
I have tried flashing all of the above firmwares (roms) one by one, but I am still having the same issue.
Can anyone please advice me on anything else that I can try.
Thanks for your time.
Best Regards.
I am still having issues with this phone, and would really like some help and advice.
I found this post with a similar issue: S3 Mini stuck in boot loop after flashing cm 10.2 try odin am i missing a step?
The above post pointed me here: Official ROOTED firmwares for the SIII mini - OXX csc
I have once again tried all the I8190N firmware (roms) listed, and I am still having the same issue as before.
Just to recap the issue that I am having.
The phone will switch on, get as far as displaying "Samsung Galaxy S3 Mini GT-I8190N" then the phone restarts, this will on happening.
If you try to start the phone in bootloader / recovery mode the phone will just display "Samsung Galaxy S3 Mini GT-I8190N" and sit there.
Powering up the phone in Odin mode seems to work fine.
Thanks again for your time.
Best Regards.
MadProfessor2002 said:
I am still having issues with this phone, and would really like some help and advice.
I found this post with a similar issue: S3 Mini stuck in boot loop after flashing cm 10.2 try odin am i missing a step?
The above post pointed me here: Official ROOTED firmwares for the SIII mini - OXX csc
I have once again tried all the I8190N firmware (roms) listed, and I am still having the same issue as before.
Just to recap the issue that I am having.
The phone will switch on, get as far as displaying "Samsung Galaxy S3 Mini GT-I8190N" then the phone restarts, this will on happening.
If you try to start the phone in bootloader / recovery mode the phone will just display "Samsung Galaxy S3 Mini GT-I8190N" and sit there.
Powering up the phone in Odin mode seems to work fine.
Thanks again for your time.
Best Regards.
Click to expand...
Click to collapse
Let me understand.
Download mode is working fine and ODIN recognizes phone ?
You tried to flash stock ROM via Odin ?
But It still stucked in bootloop ?
That is correct.
Are you sure about did you find the stock ROM ?
Behind the battery there is a paper. With S/N you may understand which baseband do you have
I am not sure about the stock firmware (rom), that is why I have been asking for help and advice.
The sticker under the battery has the following details:
MODEL: GT-I8190N
FCC ID: A3LGTI8190N
SSN: -I8190NGSMH
IMEI: ******/**/******/*
S/N: R21D7D7BEJE
Click to expand...
Click to collapse
The sticker on the NAND Flash chip has the following details:
073110
H49C BTU
HS033741
C-HVT1
I8190NXXA
Click to expand...
Click to collapse
Are you above to advice me what is the correct firmware (rom) I need with the above details?
Best Regards.
You should try kies. It will find the correct ROM but I didnt use it and its diffrent from ODIN
Kies does not work, when you have kies loaded and then plug the usb cable into the phone kies just shows connecting but fails to connect or do anything else.
You need to unistall ODIN. Did you entered your phone S/N and did kies download the files ?
simbilli said:
You should try kies. It will find the correct ROM but I didnt use it and its diffrent from ODIN
Click to expand...
Click to collapse
Here are some question about Kies.
Does Kies detect a rooted device and deny its USB connection?
Or limit any feature on it?
I`m facing a problem using Odin and USB connection while
trying to flash TWRP update on my Samsung Galaxy S3 Mini (GT-I8190N).
i have no issue using Kies to make a backup before, so i`m guesting that`s the reason.
my solution was to uninstall Kies temporarily(keeping the backup files).
Its no major problem, just trying to communicate and share opinions in this forum.
Anyone having/had this kind of problem?
Naimlaaa said:
Here are some question about Kies.
Does Kies detect a rooted device and deny its USB connection?
Or limit any feature on it?
I`m facing a problem using Odin and USB connection while
trying to flash TWRP update on my Samsung Galaxy S3 Mini (GT-I8190N).
i have no issue using Kies to make a backup before, so i`m guesting that`s the reason.
my solution was to uninstall Kies temporarily(keeping the backup files).
Its no major problem, just trying to communicate and share opinions in this forum.
Anyone having/had this kind of problem?
Click to expand...
Click to collapse
Did you installed USB drivers ?
simbilli said:
Did you installed USB drivers ?
Click to expand...
Click to collapse
I did. Probably after done the backup via Kies, I think (not sure the exact time).
I was looking forward on flashing custom ROMs.
Naimlaaa said:
I did. Probably after done the backup via Kies, I think (not sure the exact time).
I was looking forward on flashing custom ROMs.
Click to expand...
Click to collapse
Ok now If you installed USB drivers flash twrp via ODIN. Donf forget to unistall kies.
simbilli said:
Ok now If you installed USB drivers flash twrp via ODIN. Donf forget to unistall kies.
Click to expand...
Click to collapse
Thank you simbili Bro. Will flash -f2fs 2.8.1.0 version. i just got an update of CM11 Rom, maybe will use it on my Mini`s. Thanks again simbili.
:highfive:
Your welcome
I will be happy If you use thanks button :good:
simbilli said:
Your welcome
I will be happy If you use thanks button :good:
Click to expand...
Click to collapse
Done. :good:
What does the "thanks" button main effect anyway?
Naimlaaa said:
Done. :good:
What does the "thanks" button main effect anyway?
Click to expand...
Click to collapse
It just effects thanks meter not a big thing