I have had my Milestone for a while and it is out of warranty. Recently a narrow strip on the right side (when held vertically) of the phone has stopped responding to touch. It has decommissioned the search softkey, the backspace, L and the P key of the keyboard.
However, I have noticed that the touch response on the left has increased. For instance Q, A, and Z keys respond even if i touch the black edge of the screen, this goes for the back/return softkey as well.
This leads me to conclude that somehow my phone's inner working's alignment to the screen has been disturbed.
I have tried several roms...CM7, Froyomod and stock froyo but the problem remains.
I did use a third-party car charger once that gave me the ghost screen issue. Draining the batter to 0 with the app Battery Refresh and charging it to the full with Milestone charger solved the issue.
I'm in Bangladesh and there is no moto here...there is no support and sending the phone abroad for a fix is not an option. I'll have to fix it myself or save up for a few months to buy something else...not a bootloader locked moto again.
So, any suggestions? or directions I should be going or looking at?
1. The ghost touch appeared for me, too, after flashing FroyoMOD. I left the phone for ~a night slided-out, without battery, micro SD, SIM etc ) and it worked fine for ~5 days. Then, the same right side stopped working. We don't actually know what is the problem (moisture, bad charging, wear of the flex cable, defective digitizer) and we also can't be sure if we replace the digitizer the problem won't appear again. So, I suggest that you should sell the phone.
2. You could get an i9000, an LG 2x or a Desire HD.
L.E. I'm 95% sure that this isn't a software issue, so flashing different ROMs wont help.
same issue...
solution: dumped stone, got galaxy (Y)
My milestone eventually died. No M logo even. Thinking about getting a Huawei U8500 as an interim phone before I get something good.
Try Iphone insted
Once I got the same problem, it was not on the edge, but the middle of the screen & U, J & N keys stopped working. It was under warranty so I got the things replaced.
Touchwood
Related
Hello,
I'm not really sure if anyone encountered this before..
Suddenly today in the morning, I notice my Milestone's touchscreen is acting up.
I can't reach the menu button at the bottom of the screen. It always chooses Phone or Web Browser button instead :/
I use search to get to Dev Tools and Pointer Locations, and I realize there's a segment, about 1 third of the touchscreen, in the middle, unresponsive to touch.
I tried cleaning the screen, clearing cache, rebooting, it made it work temporarily, but then it returned again. I changed to stock 2.1 SBF, still no change. And now, its stuck in this state, I can't get it to work even temporarily..
I really dont want to send it to Customer Service, is there anyway to solve this?
Thanks!
Lesiroth said:
Hello,
I'm not really sure if anyone encountered this before..
Suddenly today in the morning, I notice my Milestone's touchscreen is acting up.
I can't reach the menu button at the bottom of the screen. It always chooses Phone or Web Browser button instead :/
I use search to get to Dev Tools and Pointer Locations, and I realize there's a segment, about 1 third of the touchscreen, in the middle, unresponsive to touch.
I tried cleaning the screen, clearing cache, rebooting, it made it work temporarily, but then it returned again. I changed to stock 2.1 SBF, still no change. And now, its stuck in this state, I can't get it to work even temporarily..
I really dont want to send it to Customer Service, is there anyway to solve this?
Thanks!
Click to expand...
Click to collapse
Same with me, i can't reach from menu in a bottom side to upper side, maybe 10mm dead space + 7mm right side from bottom side to upper side.
Please help me!!
Sorry my english is not good
It happen to me last 2 weeks while helping out a friend's Milestone. After i flashed a kernel, the whole screen is not working. Trying to flash back to stock ROM,custom ROM,etc but still the same.
By accident i press and hold both BACK key(the bottom left) and SEARCH key( bottom right) and ON the phone. I let go of the the two,BACK and SEARCH key after the phone is completely ON. To my surprise, it works!!! Until now the phone has no problem with the touchscreen.
I hope you guys can try this out or is it an coincidence,I don't know..
bietoff0728 said:
It happen to me last 2 weeks while helping out a friend's Milestone. After i flashed a kernel, the whole screen is not working. Trying to flash back to stock ROM,custom ROM,etc but still the same.
By accident i press and hold both BACK key(the bottom left) and SEARCH key( bottom right) and ON the phone. I let go of the the two,BACK and SEARCH key after the phone is completely ON. To my surprise, it works!!! Until now the phone has no problem with the touchscreen.
I hope you guys can try this out or is it an coincidence,I don't know..
Click to expand...
Click to collapse
thanks but no fix it for my phone
I had the same problem sometime last year, which I eventually fixed by clearing cache partition and rebooting a bunch of times.
Unfortunately, the problem re-appeared today. So far, rebooting and clearing cache hasn't worked.
By any chance, have any of you installed the WiiMote Controller App? I was convinced that was what was doing it to my phone. (maybe not, as I never re-installed it though)
I'm about to flash the sbf file, but as Lesiroth said, that might not work
i believe u r having GHOST TOUCHSCREEN syndrome
my touchscreen sometime do not response to my touch
it just went berserk!
the notification bar keep sliding up and down
if im in the menu, it goes up and down too!
sometime i cant unlock the screen bcos it do not respon
however, some chinese users found that this could be due to ripped/ torn ribbon
just google it
it is widely reported too!
I just want to say that I have fixed my Droid's touchscreen problem (or maybe it will re-appear in another six months).
Anyway, I just set the screen brightness to max and screen timeout to 30min and let the battery drain. I took the battery out for a second and then charged the phone with the USB that came with the phone over the wall socket.
I think the USB wire is the culprit (I was using a BB one for a while).
haroldz123 said:
i believe u r having GHOST TOUCHSCREEN syndrome
my touchscreen sometime do not response to my touch
it just went berserk!
the notification bar keep sliding up and down
if im in the menu, it goes up and down too!
sometime i cant unlock the screen bcos it do not respon
however, some chinese users found that this could be due to ripped/ torn ribbon
just google it
it is widely reported too!
Click to expand...
Click to collapse
my problem seemed to be disappeared after i soft reset n use stock rom
i tot launcher pro was the culprit but it is not
so i re-install LP n use for 1 day
d only problem i had was when i went for a jog, i tucked it on my waist (no in the pocket).
after that the screen stop working at all, i have to reboot by taking the battery a few time.
after 30 min or more, the problem was gone.
tis could be due to the stress applied to the screen when im joggin (as it it as "touched" while im jogging).
however, i removed beautiful widget n its addon too, dat could the source of the problem as well.
SOLUTION: soft reset, use stock rom / launcher for 1 day
if it still persist, it could a hardware problem
jtnw said:
I just want to say that I have fixed my Droid's touchscreen problem (or maybe it will re-appear in another six months).
Anyway, I just set the screen brightness to max and screen timeout to 30min and let the battery drain. I took the battery out for a second and then charged the phone with the USB that came with the phone over the wall socket.
I think the USB wire is the culprit (I was using a BB one for a while).
Click to expand...
Click to collapse
I am glad that you solved your problem. Unfortuntely the past week or so has been a really busy time for me, I could not focus on this problem. I will try your solution, although I still think it is a broken digitizer on my part.
maybe the problem is the digitizer..
try to change rom or wipe it first..
if the problem still persist i think its the digitizer..
use only the original charger..
OMFG that worked on my phone!!!
bietoff0728 said:
It happen to me last 2 weeks while helping out a friend's Milestone. After i flashed a kernel, the whole screen is not working. Trying to flash back to stock ROM,custom ROM,etc but still the same.
By accident i press and hold both BACK key(the bottom left) and SEARCH key( bottom right) and ON the phone. I let go of the the two,BACK and SEARCH key after the phone is completely ON. To my surprise, it works!!! Until now the phone has no problem with the touchscreen.
I hope you guys can try this out or is it an coincidence,I don't know..
Click to expand...
Click to collapse
----------------------------------------------------------------
A segment of my phone covering the home button went dead two weeks ago.. and duuuuude did this work!! its super smooth as ever!!! thanks a ton!!
Mine did the same exact thing! The entire strip from the home button to the top of the screen no longer works!
Sent from my SAMSUNG-SGH-I777 using XDA App
silverslasher said:
Mine did the same exact thing! The entire strip from the home button to the top of the screen no longer works!
Sent from my SAMSUNG-SGH-I777 using XDA App
Click to expand...
Click to collapse
ive the same problem, and i believe that's because of moisture. because every time when its raining except the problem with right side of screen im not even able to use the phone touch screen doesn't work at all and the phone just does something by itself! this issue started with small vertical bar from right side of screen and it growing everyday now im not able to use right side of screen till home button.
i want to know do i have to replace touchscreen or i can fix it with something to absorb humidity?
thanks in advance
Hello
One night I was using the phone without doing anything special , some video watching . Phone went dark, tried to reboot. Blank Screen and the capacitive buttons flash. Left it to charge all night, in the morning it started but after I pressed the lock button blank screen but phone still working and receiving input.
Took the battery and SD card out left it for 30 seconds then started it again, Stuck at LG logo. Repeat , phone started ... Pressed lock button once then again to unlock , screen wouldn't start.
Used LG Mobile Update recovery tool to restore it ... Didn't solve problem. Sometimes it does not even start , just flashes buttons, other times it does without screen and last all works even the screen until first time goes dark , in the last two cases I can use LG On-Screen Phone without trouble, in doing so I installed a proximity sensor test app to see if it was causing my screen to not come back on , the sensor looked fine.
Facts:
1. Two day old Optimus Black p970, worked like a charm until stated problem
2. The app that checked proximity sensor showed the sensor to be free when my hand wasn't on it
3. The warranty laws in my country are idiotic so I would do or buy anything rather than send it so they can give me a new one in 3 months.
4. Tried another battery from another Optimus, fully charged nothing different.
5. Stock rom.
Do any of you fine people have some ideas on how to fix this? Thanks in advance
Hi there...
Sometime ago [1 year and a half or so~] I worked at a cell refurbishing facility [there were samsung, motorola and palm devices from sprint] and that problem you have was quite usual. Blank screen, still the phone is somehow usable like reciving calls...
There's this thing called "flex" which is the connector between board and display and that is what we fix, most of the time not even "fix it" just getting it in the right place...
This happen because of excesive use in those sliding or clamshell devices, in OB could be for overheating, you could try to fix it yourself or pay $20 usd [that's what it cost here]
Would that connector explain the fact that sometimes it doesn't start at all? hmm I am thinking now and I guess if it moves and somehow the phone feels it has not display connected it could fail to start... Anyhow thank you
actually yes, it could be only for the flex [some devices don't start at all when not having display or keyboard if there's any] but since our OB is not sliding nor clamshell type probably was overheating.
you say you have stock rom, well now I'm using CM7 but when I was at stock and after using the phone a few minutes it felt warm and some more minutes [like playing gunbros where you need to use both hands and a lot of movement] it was really hot and had to stop playing for a while.
what I'm trying to say is that because of overheating flex could have moved, but because of overheating too may have move something else, you couldn't belive the huge number of micro-things that reside in the board.
so if it's only the flex, it's an easy task to do, just unplug and plug again, but if it's something else it's quite hard to know just looking at it, you need to do some electric measures and stuff, the recomendation is to take it to a tech center or something
Hi. I Have same issue. Two times when i press power buton, butons flashing and screen still black. Phone not responding. I must remove baterry.
Sent from my LG-P970 using Tapatalk
Hi there, got the same problem too with my optimus black. Screen goes flickering, shut down don't do any good, and the phone temperature is kinda hot. But in my case it work after I clean some cache and data in the phone storage through LG OSP. After that, the phone temperature back to normal and the phone screen back to normal also. I believe that in my case the phone is overheated.
Hello,
I have sent my gnexus off to be repaired this week and recently started to use my old milestone until my other phone is repaired. Phone was working fine, a little slow to my nexus but it was better than nothing. I was checking my emails and stuck my phone in my pocket to cross the street, when I pulled it out again, the screen would light up (glow) but the screen was black, I tried pulling the battery and rebooting but to no avail. I can feel the phone vibrate when I slide my finger across to unlock it and tap icons, but nothing is being displayed. I'm wondering if anybody else has had something like this happen and if it is possible to fix relatively easily?
If you don't get anything on the screen anymore I'm afraid it's a hardware failure.
Maybe the connector cable is broken (partially), I guess...
I guess Eiertschik is right.
In the boot process, does the M logo show up?
Hello Everyone!
So i'm really stuck over here. I have an international Samsung Galaxy Note N-7000 that is working but with a black screen!
First of all i want to discuss exactly what i have done:
1.i had a problem with the charging port where it works sometimes and most of the times doesn't. So i decided to order a new charging port to replace the existing one.
2. When i received the new charging port i instantly started to dissemble the device (The device was working perfectly before starting replacement)
3. After i removed the old one and installed the new, i turned on the device and it showed only a black screen, then after some time i saw the touch buttons light, but still the screen is black:crying:
4. so i decided to return back the old charging port and this time when i turned on the device it sounded like it's booting and working but still with a black screen. The phone even received call and the touch screen is working but with black screen.
What do you guys think has just happened to my phone? could the new charging port cause any problems with the motherboard?
i'm really stuck and don't wanna go to a service center
I have recorded a video of the problem. Please see it below
since i'm new over here, i'm not allowed to post youtube link.
please head to youtube and type my username and watch the video : nadeaa0a
thank you very much
My younger brother always liked to disassemble things with a hammer wondering after why it wasn't possible to assemble it the other way around.
It took him a few years to understand that real knowledge of things is a clear advantage.
Go to a service center and get help from a professional instead of making it ...
Sent from my GT-N7000 using xda premium
maybe you disconnected the wire you were changing ports ! don't worry and don't freak out just take to any shop and they will check it i don't think the screen is burnt because if it was it would be more expensive ! go to any shop and ask them to change ports and check the screen
for what you described, my best guess would be either you unplugged the lcd and didnt plug it back in properly.... or you damaged the flex for the lcd... the charging flex wouldnt cause the problem... just inspect the lcd flex and plug for damage... if no visible damage plug it in again and try it again... lets hope its just not plugged in right...
I have the same problem
Hi,
I have the same problem. I had never disassembled my phone and the screen slowly turned purple and started blackening out. It was fully functional. This I knew because I connected it to my Windows 7 computer and used Android Commander. I ordered a new screen complete with bezel etc. I have two batteries, the first didn't even charge after I put it in the phone (it had drained totally during the wait for the new screen), the second was partially charged and allowed the screen to boot. It is however behaving like the first screen did before it went black, that is purple. I am sure I have not done anything wrong with the connections. Could it be the batteries? or the adapter flex? I just hope it is not the mainboard. It is not on warranty and we don't have that many honest phone specialists around where I live. I am almost sure others have experienced the same problem and someone on xda knows what the problem is. If you do I would be indebted.
nadeaa0a said:
Hello Everyone!
So i'm really stuck over here. I have an international Samsung Galaxy Note N-7000 that is working but with a black screen!
First of all i want to discuss exactly what i have done:
1.i had a problem with the charging port where it works sometimes and most of the times doesn't. So i decided to order a new charging port to replace the existing one.
2. When i received the new charging port i instantly started to dissemble the device (The device was working perfectly before starting replacement)
3. After i removed the old one and installed the new, i turned on the device and it showed only a black screen, then after some time i saw the touch buttons light, but still the screen is black:crying:
4. so i decided to return back the old charging port and this time when i turned on the device it sounded like it's booting and working but still with a black screen. The phone even received call and the touch screen is working but with black screen.
What do you guys think has just happened to my phone? could the new charging port cause any problems with the motherboard?
i'm really stuck and don't wanna go to a service center
I have recorded a video of the problem. Please see it below
since i'm new over here, i'm not allowed to post youtube link.
please head to youtube and type my username and watch the video : nadeaa0a
thank you very much
Click to expand...
Click to collapse
it shows as color black, or nothing (like locked device)? I used to face this problem too with my infuse 4G, but it was because of installing custom rom. Had problem with few rom i installed but nothing happen on my stock one. If your device is just not lighting up(like locked device), then i guess because of ROM, but i'm not sure yet. But if it shows "color black", then i don't know.
THIS IS NOT A SOFTWARE BUG. Its the Screen flex or the ribbon. Disassemble the back part, and take a look at the flex or the ribbon connector of the screen, clean the conector with a tooth cleaner with alcohol and let it dry for a few minutes. Put it back on and mount the back part again. Test it, it should work.
Same thing here: changed the usb port, booted fine, had issues with the sim, turned off took it apart again to check, put it back on and black screen.
Yea having the same issue here, dismantling the usb module and put in new one, power up black screen!! The menu and back button did lights up, and the phone is working too, can hear the booting tone, anyone got any solution for that yet?
jasonhs said:
Yea having the same issue here, dismantling the usb module and put in new one, power up black screen!! The menu and back button did lights up, and the phone is working too, can hear the booting tone, anyone got any solution for that yet?
Click to expand...
Click to collapse
You damaged your LCD flex cable or didn't plug it in correctly ..
N00b... said:
You damaged your LCD flex cable or didn't plug it in correctly ..
Click to expand...
Click to collapse
I have unplugged and replug back few times, same result. Guess most probably i have damaged the flex cable. Replacement part seems too pricy to change, rather buy a new phone.
Sent from my GT-P6800 using Tapatalk
Hello,
I know a lot of us are having problems with displays and digitizers and im wondering if anyone else has this problem. Yesterday i replced my screen because it had a dead zone. I booted up the phone and everything worked great until i locked the screen. When i pressed the power button to unlock it there was just a black screen with lots of white lines forming. Without fail the phone will do this. I restart and its fine but when i lock it, it gets screwy. I really need to get this working since i dont even have a backup phone right now. By the way the display is not oem its a knockoff.
Since you change your LCD....it might be a different panel from your original. Check your kernel or flash the kernel again.
Sent from My LG G2 LS-980 or LG G Pad 7.0 V400
Same thing happen to me about a month ago during my G2 screen repair. I bought mine on ebay from a seller that had sold hundreds of them, figured I couldn't go wrong. Unfortunatly I never figuered out why it was failing and just ended up returning it for a refund. The second screen I bought was from etradesupply and it worked perfectly. Hopefully someone has a fix for this weird issue.
I had that exct thing happen to me, well rainbow colored lines. I shattered the screen on a corner drop. I took it to Gopher Mods, they replaced the screen and within a few minutes it happened. They replaced it 2 more times and eventually the last time the screen popped out a little bit since they did not add enough glue/sticky tape inside and the lines dissapeared. They also gave me a full refund, with which I got another G2. So two working phones now lol.
Basically the screen might be pressed in too tightly causing the cable inside to be kinked too much. Its very easy to damage the video cable in this phone mind you.
Bmatthews11 said:
Hello,
I know a lot of us are having problems with displays and digitizers and im wondering if anyone else has this problem. Yesterday i replced my screen because it had a dead zone. I booted up the phone and everything worked great until i locked the screen. When i pressed the power button to unlock it there was just a black screen with lots of white lines forming. Without fail the phone will do this. I restart and its fine but when i lock it, it gets screwy. I really need to get this working since i dont even have a backup phone right now. By the way the display is not oem its a knockoff.
Click to expand...
Click to collapse
Try installi mg dorimanx's kernel which detects your panel type of search the thread for a kernel swap flashable. Your new panel may be of a different type causing the white lines.