Mteor Slow not start after flash - HTC Breeze

Hello,
I have problem with Mteor, I flash ROM RUU_BREE100_1.13.251.2_1.06.00.10_QtekEUR_Ship_R3 to Mteor but he is extremly slow 10 minutes to start and can't use. So problem is, that I can't flash any other ROM. I take Mteor to service center but they say me that problem is mainboard, but I thing this is not true...
IPL 0.90
SPL 1.10
can anyone help me?
thank you!

st.tom said:
Hello,
I have problem with Mteor, I flash ROM RUU_BREE100_1.13.251.2_1.06.00.10_QtekEUR_Ship_R3 to Mteor but he is extremly slow 10 minutes to start and can't use. So problem is, that I can't flash any other ROM. I take Mteor to service center but they say me that problem is mainboard, but I thing this is not true...
IPL 0.90
SPL 1.10
can anyone help me?
thank you!
Click to expand...
Click to collapse
you try to get into Bootloader mode attach the USB cable and flash the new ROM

Related

Stuck at bootscreen after flash

I just flashed my Qtek 9100 with the T-mobile rom "RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe" from the ftp. I have tested a lot of different roms without trouble. But after the flash my Qtek is stuck at the bootscreen just displaying
IPL 1.06
SPL 1.06
GSM 01.12.10
Tried a hardreset and it says format complete but after a reboot I am stuck at the bootscreen again. I am terrified - can I make my beloved qtek to work again or is it just a piece of expensive junk now ?
Sorry, stupid me I was as easy as start in USB mode and reflash and it booted normally again
easycure1974 said:
I just flashed my Qtek 9100 with the T-mobile rom "RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe" from the ftp. I have tested a lot of different roms without trouble. But after the flash my Qtek is stuck at the bootscreen just displaying
IPL 1.06
SPL 1.06
GSM 01.12.10
Tried a hardreset and it says format complete but after a reboot I am stuck at the bootscreen again. I am terrified - can I make my beloved qtek to work again or is it just a piece of expensive junk now ?
Click to expand...
Click to collapse
I am in the same situation now..
I am trying to re-flash the original ROM now, enter the booloader menu by holding voice-dial+CAMERA while resetting. then connect USB an try to re-flash.. It works for 30 minutes now without luck, I don't know what to do either... HELP!!
and a hint to those that are NEW: if you want to screw up your device, play with ROM upgrades... you will end up like us..
easycure1974 said:
Sorry, stupid me I was as easy as start in USB mode and reflash and it booted normally again
Click to expand...
Click to collapse
PLEASE help me, what utility did you use to reflash?
Just press the camerabutton and reset and then you will come to the USB mode and then just used the flash utility file again and start the flash again and then it shall work.
I used the RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe form the ftp once again and it worked
easycure1974 said:
Just press the camerabutton and reset and then you will come to the USB mode and then just used the flash utility file again and start the flash again and then it shall work.
I used the RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe form the ftp once again and it worked
Click to expand...
Click to collapse
doesn't work form me because I didn't unlock before it crashed.. now I can't re-flash it..
ok, but then use the right official flash for your device - if it is a qtek use a qtek flash or imate if it is an imate device. The most flash files is available on the ftp.
easycure1974 said:
ok, but then use the right official flash for your device - if it is a qtek use a qtek flash or imate if it is an imate device. The most flash files is available on the ftp.
Click to expand...
Click to collapse
10x easycure, you are an easy cure for my troubles I am downloading it and I am sure it will work this time ( have a QTEK 9100)
Another question: did RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe upgrade your radio ROM as well? what machine do you own? I think of flashing it eventually as well..
I hope it will work for you!
Yes the t-mobile upgraded everything - but it has a lot of crap in the extended rom that I don´t like and with the new rom versions it doesn´t seem possible to delete anything from the extended rom.
So I will flash it again when a newer flash from qtek is available. Tried the Qtek_9100_1_6_7_ENG.zip rom but it is just OS - I dont like the idea of using OS from Qtek and the rest of the software from some other brand.
I have a swedish Qtek 9100
easycure,
I don't like the crap either but I found someone's suggestion to soft reset the device just before installing software from extended ROM (just after aligning screen). I just had to install some CAB's manually to get MMS support etc.
Hope this helps you also
Priit said:
easycure,
I don't like the crap either but I found someone's suggestion to soft reset the device just before installing software from extended ROM (just after aligning screen). I just had to install some CAB's manually to get MMS support etc.
Hope this helps you also
Click to expand...
Click to collapse
I tried that but I didn´t got the mms to work with that but then I shall make another try with that!
I installed Shortcut-MMS1-JAVA6XX-CV-VOICE-EmailWiz-TMO-03Nov05.CAB to get MMS support. I also installed coouple of CABs that had "Camera" in the name hoping it will improve camera functionality or something

Charmer crashed with the new Aku 3.3!

Hello!
I tried to flash my Charmer with the new german Aku 3.3. At first everything seems to be ok, but at 95% it stops and i got the Message: update error- there is an comunication problem! So what can i do? I tried to flash the old rom back but there comes also at 95% a message: invalid command - nfb file cannot be used for your pda!
Please help me !
Greetings Musna!
Ps: can somebody upload a sd image for the mda compact II !
Go to bootloader mode, then try to flash RUU rom (1.x). You can find it on Charmer wiki.
It doesn`t work too, it always stops at 95% has anyone another idea?
did you try hard reset?
Yes i tried hard reset, but it is always in bootloader!
I have also the same problem. Tried to upgrade to version 3.3. Everytime it stops at 80%. I don't know why?! I can repair it with the software and re-run it. But it has the same effect.
Now i will try to downgrade to 2.6 again. I really don't understand what causes the problem. I hope i will get this thing running again....
EDIT: I reflashed the device with the older 2.6 ROM and it is working right now. However I didn't really get why it gets stuck at 80% with 3.3 ?!?!
nitrane said:
I have also the same problem. Tried to upgrade to version 3.3. Everytime it stops at 80%. I don't know why?! I can repair it with the software and re-run it. But it has the same effect.
Now i will try to downgrade to 2.6 again. I really don't understand what causes the problem. I hope i will get this thing running again....
EDIT: I reflashed the device with the older 2.6 ROM and it is working right now. However I didn't really get why it gets stuck at 80% with 3.3 ?!?!
Click to expand...
Click to collapse
The aku3.3 is up to date the bootloader version!!!
IPL and ISP version now is 3.00.
http://www.windowsceportal.hu/forum/viewtopic.php?t=1079
Sorry but i do not speak hungarian. What do you want to tell me ?
I´ve got the same: My charmer is in Bootloader IPL 2.06.0001 SPL 3.08.0001
I can´t downgrade to AKU 2: Please order a newer Version.
Every try to upgrade to AKU 3.3 failed at 95% with Error 326.
Is there any help for my charmer???
oh.**** !!!! I got the same problem with them and my first pda uk rom already empty screen and then i try with my scrond pda German rom it the same problem and now just only show in bootloader screen.Have i ask someone who knowage about this he told me that if SLP in you PDA have chang it be hard to repair.So,I think I lose 2 PDA did I try to flash in T-Mobile Official Rom de that i hope to develop it but i hve to kill 2 Charmer.Who take responsibilities,T-Mobile right ???
Ok no problem you can repair it! At first you have to brand your device with the rom you want to! After 95% the Problem will come again! When it stops you have to go with a reset to bootloader again.When your device is in bootloader you have to install the Radio Rom from this thread:
http://forum.xda-developers.com/showthread.php?t=302768
After that your device will be able to boot again and it should work!- But the Problem during the installation will stay,so you have always to use this way to flash your Mda compact II!
In the new rom there must be a problem with the radio rom and this causes the broken device.
I`m sorry for my bad english but i`m not used to talk very much! So i hope you understand what i mean!
Greetings from Austria Musna!
that link is broken
Then try this one:
ftp://xda:[email protected]/Prophet/Radio_Roms/Prophet_G4_RadioRom_v2.47.11.exe
You can find the radio rom also on the ftp server. Prophet> Radio Roms>Prophet_G4_RadioRom_v2.47.11.exe
You can try different Radio Rom versions, i have flashed the v.247.11 and it worked.
Normaly it should work!
Thank u so much !!! My Charmer secrond PDA come back have life again and it can working.So,my Charmer first PDA UK rom still empty screen and notthing working when i press any button.Who can slove this problem !!
Musna do you have any massage such as msn

How to fix a bad radio flash ? "no gsm" on boot

Hi, i've bough a p3600 on ebay.
The seller tell me the phone is out because he flash a bad radio version on the phone.
I try to upgrade some file. ( Rom OS, Radio, SPL,etc ...)
I try the splexploit...
BUT ... The phone already stay on startup. i can see HTC startup screen,the windows startup screen ...but never the today screen.
I try hard reset, htc official rom, cookeed rom,...but when i flash a rom with "gsm", the update freeze at 13%
I try with usb and with sdcard..same thing, already stay at 13% !
But if i flash hard spl, 100%, if i flash OS, 100%, just the radio freeze at 13%
Any idea please ?
update
after the boot, i've got a "no gsm" message near the radio version
other people got the same problem like me ...
God oli, help me please
I more or less had the same thing and solved it with the sc card flash page.
http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
A rom that works for me to flash it back to the working original
http://www.allaboutphones.nl/forum/request-originele-spv-m700-rom-p3600-rom-t727.html
To download you have to register with them.
GL
Hi, updating the radio to 1.56 crashed, now I have the No gsm message and doesn't boot, running mtty from bootloader with info2 command it says supercid but I can't update any official rom SPA, WWE, ITA... the error is "vender id invalid". I've tried the sd method but returns to bootloader .
Any help will be appreciated.
You should try SSPL : http://forum.xda-developers.com/showthread.php?t=293632
And if it doesn't work the Des' Crash-Proof SPL :
http://trinityguides.info/index.php?option=com_content&task=view&id=39&Itemid=66
and try to flash a radio rom again !
doesn't work
try again and again ...the phone block at 13% ( when the radio upgrade begin) ...
pfffff
I've the same problem and after several attempts without result I sent the phone to the workshop and they told me the problem is with the main board! (this cost almost the price of phone itself). Moreover, I've seen some where here that the problem could be caused by radio chip but I couldnt get the detail.
If you find a solution give me a tip.
i've test lot of thing.
I progress with mtty. but i've got a problem ..i can't downgrade the phone under SPL 1.05.
SPL 1.04 can "reset" the radio, or enter directly to the radio bootloader. With that, i can save my phone.
Try mmty (see the wiki => bootloader info) and with the mfg spl, you can try the method.
Guys,
I've got the same problem...
I've sim and cid unlocked my spv m700 some time ago, using wonderful software from pof. Everything went smooth.
Today I've decided to update radio rom to 1.38.00.11 to enable gps.
I've launched RUU, everything was ok till 44%, when I've got message "Communication error".
After that program tried to recover rom without success, I've got another message "Image corrupted"...
I've tried to reboot my spv (both SR and HR), after rebooting I see:
M 05
B 05 D 1.23
then those symbols disappear and I see only Orange logo.
That's it... The end...
Should I reload radio rom or both rom and radio rom to my DEAD spv? If yes - how?
Please help as I'm very disappointed, frustrated and so on!
Thank you!
Update: A-A-A!!! I did it! I revived my spv! Let me explain how (I'm kinda new to all this rom and and ssl things, so forgive me for mistakes, if there are any):
1 I ran unbrick software. Yesterday it did not work (said, that could not find smth), but today it worked fine.
2 I ran RUU and BINGO! That's it!
BTW, I have vista, but it still worked (I think, thanks to Windows Mobile Device Center, which I have installed).
Also, I killed wmd process in Task manager in the beginning (have read this recommendation somewhere).
Thanks to everybody for their help!
nyco,
could you please explain briefly what you did exactly and which radio and rom you used
thanks and regards
Flash HSPL, then issue task 2A command from mtty. Flash full ROM.
Thanks stepw...
when I hit task 2A nothing happens.
Original ROM doesnt respond. I flash with cooked ones. Result 100% successful. I restart the phone- hang at boot screen.
stepw said:
Flash HSPL, then issue task 2A command from mtty. Flash full ROM.
Click to expand...
Click to collapse
Hi,
I'm already under the hard SPL. and "task 2A" not working.
Macars, try only with radio ripped or full original rom (from htc or cooked with radio) because some cooked rom have only OS.
Can you tell me what SPL you have?
Hard SPL?
Have you try splxploit ?
Can you tell me what rom you try oviplokos1 ?
thanks,
it shows SPL 9.99 and with this I cannot flash anything so what I do is to update with splxploit and then the phone changes to SPL 1.2 olipro. With 1.2 I can only flash coocked ROM and will go until the end 100% successful- (original ROM the phone does not respond), but when restarts with newly loaded cooked ROM the phone hangs at window login screen and when put it in bootloader the SPL 9.99 returns again.... the story goes on like this.
I'm becoming mad....
hi,
you can only flash cooked rom because the rom you flash contains only OS. When you flash HTC rom, the rom contains os+radio+spl+....other thing ...
Try this method to downgrade your SPL (9.99) to oli 3.20 :
1°) run splxploit
2°)when the phone reboot on the spl 1.20 oli, run HardSPL 3.20 olipro. (search on the wiki or the trinity forum
3°)upgrade to 3.20 oli ...
Now, when you go to the bootloader, you can see SPL 3.20 oli.
Try reflashing a radio only (see the upgrading topic, you will see radio 1.56.xxxx)
Tell me if this method work.
When i'm on spl 3.20 oli, i can load radio rom to 0%
when I downgrade my phone to spl 1.05, and i can run the upgrading to 7% (best score )
To downgrade to SPL 1.05:
edit the "unbrick.bat" on the splxploit folder.
Replace TRIN_HardSPL.nb to TRIN_SPL105.nb
try to find SPL 1.04. I'm sure if i got the spl 1.04 i can revive the phone
Did exactly as you said final result:
When i'm on spl 3.20 oli, i can load radio rom to 0% (and stays there )
hi,
ok, try to load spl 1.05 with splxploit, and when it is load, run radio upgrade (1.56.xxxx)
Try to find spl 1.04 and mtty it can be reset the radio bootloader
if you find 1.04, give me it
hi nyco,
I tried with SPL 1.05 the result is the same as your reaches 7% and restarts. I'm still trying to find SPL 1.04 I found one for Hermes I tried but didnt work failed.
macars said:
hi nyco,
I tried with SPL 1.05 the result is the same as your reaches 7% and restarts. I'm still trying to find SPL 1.04 I found one for Hermes I tried but didnt work failed.
Click to expand...
Click to collapse
arf :/
You got exactly the same problem i have.
did you check if you have bad block (with mtty)
try format the phone with mtty.
i contact pof, but he doesn't answer me

New Official ROM Upgrade- Release Date: 2009-04-14

I've tried to download the ROM, but HTC tell me this "Sorry, this software download is not suitable for your device".
Maybe my device s/n number is not correct.
Maybe someone who has the correct s/n could download this ROM~
Just tell you guys the news~
http://www.htc.com/europe/SupportDownload.aspx?p_id=174&cat=2&dl_id=537
Caxio's and frednd's DownLoad Link--(I wanna say THANK YOU VERY MUCH!)
See page3 #21 & #23
Filename is :
HTC Touch 3G_MR2009_RUU_Jade_HTC_Europe_2.32.401.2_Radio_Sign_12.41.30.16_0.41.30.12_Ship
edit:
on booting the last red line (after radio and protocol) now says :
D 2.32.44800
Date (which shows after first boot) after screen calibration is now set to 25/03/09
(in settings / about) Build : 5.2.20771 (20771.1.4.6)
(in settings / device info) : rom version 2.32.401.2(44800)
ON customization after first boot if scaned for wifi networks and poped up a message about available networks
Ht845kh14923 :d
o2p63 said:
Ht845kh14923 :d
Click to expand...
Click to collapse
This is for italian version.
Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??
Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??
It seems HardSPL 1.40oli and this 2.32 rom don't work very well.Very sluggish and phone can't turn ON even after 2 Hard resets.
What is your experience???
Do not install if hard spl
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Could anyone check, if the gps-support has been improved?
km
lexx2009 said:
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Click to expand...
Click to collapse
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
update : Jade is fine now. New SPL is 2.32.0000 . More testing to be done.
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
lagoskon said:
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
Click to expand...
Click to collapse
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Myster said:
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Click to expand...
Click to collapse
This is on the Hard-SPL page along with the Oli version
http://forum.xda-developers.com/attachment.php?attachmentid=166262&d=1236988725
GPS seems to work fine now, also the scroll behavior of opera is better
km
It is annoying that hardspl doesnt work with this upgrade of jade.. can't built a rom now with the new oem. It's all newer than the iolite versions, but still doesnt include Footprint
Any changes in Manila? New tabs? Calendar? Stocks? Changes in the contacts?
Hi
What is the Radio version in this new ROM?
I have just applied the version from here and if this contains the old Radio then I can hold off for now until hopefully a compliant Hard-SPL is made, I can live without Opera being perfect.
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
nereus114 said:
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
Click to expand...
Click to collapse
Install a different rom from this forum-> Shut down your jade, unplug it. Hold down "volume down button" and ""power on button" to get in to boot mode. now start to flash another rom.
when finished you can install stock spl and then install this new rom
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
jarel said:
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
Click to expand...
Click to collapse
that's right.. but i think it's in one of the drivers. using the old drivers and the new oem/sys makes it possible to run it with the current hardspl.
radio in this rom 0.41.30.12
no changes in manilla tabs, don't know what changed but it's newer

Need Original WM6 ROM for i-mate KJAM

Helloo all helpers
I need a original imate WM6 ROM for i-mate KJAM (wizard) can any helper give me the link to download.
Thanks in advance
a 6.5 rom for i-mate k-jam needed!!
hi everyone,
everytime i try to flash a 6.5 rom to my k-jam it freezes on the (red green blue) screen..
and in the RUU it says check your USB cable more like a connection problem but i tried 3 cables all with the same problem..
i thought it might be the wrong ROM but i really dont know..
any help will be appreciated
BIG SHF
BIG SHF said:
hi everyone,
everytime i try to flash a 6.5 rom to my k-jam it freezes on the (red green blue) screen..
and in the RUU it says check your USB cable more like a connection problem but i tried 3 cables all with the same problem..
i thought it might be the wrong ROM but i really dont know..
any help will be appreciated
BIG SHF
Click to expand...
Click to collapse
Did you superCID or HardSPL before you tried to flash?

Categories

Resources