Database Develop

Charmer crashed with the new Aku 3.3!

Hello!
I tried to flash my Charmer with the new german Aku 3.3. At first everything seems to be ok, but at 95% it stops and i got the Message: update error- there is an comunication problem! So what can i do? I tried to flash the old rom back but there comes also at 95% a message: invalid command - nfb file cannot be used for your pda!
Please help me !
Greetings Musna!
Ps: can somebody upload a sd image for the mda compact II !

Go to bootloader mode, then try to flash RUU rom (1.x). You can find it on Charmer wiki.

It doesn`t work too, it always stops at 95% has anyone another idea?

did you try hard reset?

Yes i tried hard reset, but it is always in bootloader!

I have also the same problem. Tried to upgrade to version 3.3. Everytime it stops at 80%. I don't know why?! I can repair it with the software and re-run it. But it has the same effect.
Now i will try to downgrade to 2.6 again. I really don't understand what causes the problem. I hope i will get this thing running again....
EDIT: I reflashed the device with the older 2.6 ROM and it is working right now. However I didn't really get why it gets stuck at 80% with 3.3 ?!?!

nitrane said:
I have also the same problem. Tried to upgrade to version 3.3. Everytime it stops at 80%. I don't know why?! I can repair it with the software and re-run it. But it has the same effect.
Now i will try to downgrade to 2.6 again. I really don't understand what causes the problem. I hope i will get this thing running again....
EDIT: I reflashed the device with the older 2.6 ROM and it is working right now. However I didn't really get why it gets stuck at 80% with 3.3 ?!?!
Click to expand...
Click to collapse
The aku3.3 is up to date the bootloader version!!!
IPL and ISP version now is 3.00.
http://www.windowsceportal.hu/forum/viewtopic.php?t=1079

Sorry but i do not speak hungarian. What do you want to tell me ?

I´ve got the same: My charmer is in Bootloader IPL 2.06.0001 SPL 3.08.0001
I can´t downgrade to AKU 2: Please order a newer Version.
Every try to upgrade to AKU 3.3 failed at 95% with Error 326.
Is there any help for my charmer???

oh.**** !!!! I got the same problem with them and my first pda uk rom already empty screen and then i try with my scrond pda German rom it the same problem and now just only show in bootloader screen.Have i ask someone who knowage about this he told me that if SLP in you PDA have chang it be hard to repair.So,I think I lose 2 PDA did I try to flash in T-Mobile Official Rom de that i hope to develop it but i hve to kill 2 Charmer.Who take responsibilities,T-Mobile right ???

Ok no problem you can repair it! At first you have to brand your device with the rom you want to! After 95% the Problem will come again! When it stops you have to go with a reset to bootloader again.When your device is in bootloader you have to install the Radio Rom from this thread:
http://forum.xda-developers.com/showthread.php?t=302768
After that your device will be able to boot again and it should work!- But the Problem during the installation will stay,so you have always to use this way to flash your Mda compact II!
In the new rom there must be a problem with the radio rom and this causes the broken device.
I`m sorry for my bad english but i`m not used to talk very much! So i hope you understand what i mean!
Greetings from Austria Musna!

that link is broken

Then try this one:
ftp://xda:[email protected]/Prophet/Radio_Roms/Prophet_G4_RadioRom_v2.47.11.exe
You can find the radio rom also on the ftp server. Prophet> Radio Roms>Prophet_G4_RadioRom_v2.47.11.exe
You can try different Radio Rom versions, i have flashed the v.247.11 and it worked.
Normaly it should work!

Thank u so much !!! My Charmer secrond PDA come back have life again and it can working.So,my Charmer first PDA UK rom still empty screen and notthing working when i press any button.Who can slove this problem !!

Musna do you have any massage such as msn

Htc Breeze Test Sspl

So, guys, here is the first test SSPL for breeze. I have no breeze, so please report if it works.
extract to your device root!!!
start spl.lnk AND immediately press POWER and CAMERA buttons. (or try hust CAMERA)
if the screen shows sth like spl 1.01 DFR, then everything is ok - it is my spl
this version was intended to allow you to flash any CID rom update and unsigned nbh files. the next release will be based on the latest spl and include compatibility with new RUU of 1.34 rom updates and the feature to fix bad blocks.
EDIT - may 10, 2007 - SSPL V1 works successfully
CID check - disabled
NBH check - disabled
attached spl in nbh format for flashing - breeimg.zip
Thanks to:
DES for his SSPL
Olipro for his hard spl which actually saved me from hours of IDA analysing - I simply compared his spl to original and patched the one from breeze

at first try...
i have exactly what i descriped here:
http://forum.xda-developers.com/showpost.php?p=1253965&postcount=782
after the reboot i can't get into the bootloader...
what did you changed in the spl ?! or in the sspl.exe ??

I try... It's WORK!!!!!

what did you do??
edit:
ok, strange things goes on here ... just tryied it another time yet...
ipl-sspl by Des
SPL-1.01
should work
if i have time today i will try to made an cooked rom ...
if this works i look for a way to extract the files out of the excalibur wm6 rom ...
edit2:
i now have the problem that i can't connect mtty to bootloader... mtty ends with error when producing the cmd command line... i just had this problem with hermes to... i have 2 mtty version on all the 2 the same error...
i will try it now on a other machine..

1) Rename the BREEZE_HTCEUR_1.34.251.1_SHIP.nbh file to BREEIMG.nbh
2) Copy to sd card
3) start spl.lnk and immediately press POWER and CAMERA buttons
4) Phohe start in bootloader and flash new rom. (but no new radio)

THX
Thx for the replies, i`ll try to make a newer sspl. also, let`s begin the work for wm6 for breeze based on hermes rom... but in another thread some time later

can anyone confirm that they have sucessfully flashed a cooked ROM onto a breeze? Please update the wiki.

doedoe said:
can anyone confirm that they have sucessfully flashed a cooked ROM onto a breeze? Please update the wiki.
Click to expand...
Click to collapse
Hi, i work on it!!
on afternoon/evening i will try to cook a rom with a few freeware tools bases on the actuell rom!!
i can begin working on wm6 rom recently when extract the excalibur content... because of the problem that breeze is a smartphone an hermes a ppc there would be some problems with coredll's of the system! because of that i need smartphone wm6 rom... befor that there is no wm6 on breeze possible!
....
can anyone else can try mtty with the sspl ?
-----
engel98 said:
1) Rename the BREEZE_HTCEUR_1.34.251.1_SHIP.nbh file to BREEIMG.nbh
2) Copy to sd card
3) start spl.lnk and immediately press POWER and CAMERA buttons
4) Phohe start in bootloader and flash new rom. (but no new radio)
Click to expand...
Click to collapse
this should work when you have a new spl installed - and you want to flash another cid rom!!
has nothing to do with unsigned code!!
!!! only for understanding!!

hey what should i say...
it just look like that it works...
i have cooked a rom now...
only small reg changes!!
i have flashed it with hermes RUUUpdaterV2
only a OS file!
Phone boots! now i have to check if the changes are taken over!!
But why not ;Þ

Please post to the wiki.
I am hoping that we can use tornado WM6 code to cook a WM6 image...

I just added some Infos to wiki!!
Updated:
Breeze/MTeoR Upgrading Guide (4Hard/S-SPL)
Custom RUU Updater

I can also confirm that this SSPL truly works, but I am still unable to flash 1.38 radio over 1.29 currently installed with this SSPL version.
Any hints when could we expect SSPL based on some newer SPL release (like 1.09 or 1.10)?

just extract the radio rom what you want from an shipped rom ...
take it and re nbh's it with the nbgehn utility ... than put it in the custom ruu folder start ruuwrapper and flash it...

futureshock said:
just extract the radio rom what you want from an shipped rom ...
take it and re nbh's it with the nbgehn utility ... than put it in the custom ruu folder start ruuwrapper and flash it...
Click to expand...
Click to collapse
Tried that 3 times already. Doesn't work! Although process finishes whithout any glitches, System Info still says Radio ROM 1.29.00, and my phone still acts like crap...

.... i tried it too ... no problem... you should have done a mistake...
download an usb sniffer and let it run when updating... maybe then we can see the error...
but i had done it too... with sspl had no problems!!

I confirm this is also work on my dopod 595.
Now I need to search how to change the splash screen

what would you want to change??

futureshock said:
.... i tried it too ... no problem... you should have done a mistake...
download an usb sniffer and let it run when updating... maybe then we can see the error...
but i had done it too... with sspl had no problems!!
Click to expand...
Click to collapse
This is what I did/have...
- I have installed Radio ROM 1.29.00.10 (with older 1.32.251.1 RUU)
- My MTeoR is CIDed QTEK_A07 - all available RUUs fail with INVALID VENDOR ID error
- If I use SSPL (linked in this thread), my MTeoR actually does start SuperCIDed and I can run any RUU or custom ROM, and although all of them complete with success Radio ROM DOES NOT CHANGE at all.
My theory is (based on posts in Hermes upgrading forum) that Radio ROM 1.29 installed Radio BL 0108 which in turn does not allow flashing Radio ROM when started SPL is pre-1.09 codebase. I presume that it flashes with 1.09, 1.10 or newer only (makes sense because HTC released new 1.34 RUU which first installs SPL 1.09, then the rest of ROM).
Can anyone concur with my assessment or am I completely wrong?

Ohhh,thank.It works perfectly on my HTC MTEOR from O2 Czech Republic.

sp3dev said:
So, guys, here is the first test SSPL for breeze. I have no breeze, so please report if it works.
SSPL V1 works successfully
CID check - disabled
NBH check - disabled
Click to expand...
Click to collapse
WOW
I have now read for weeks the Hermes/Trinity threads wondering if this would be possible for "simple" smartphones too - and you did it
So while it is possible for the MTeor, maybe your kind of patching the SPL would also work for the Excalibur/S620?
I would love to flash my O2 Cosmo, but want to have an original ROM Backup for warranty/fallback reasons.
I also found out that it is possible to extract and cook ROMs for it like the way for the Hermes - but I cannot flash because of this f****g need for signed .nbh.
May be you are able to do this MAGIC on a Excalibur SPL too?
I would try out on my phone if you want to take the challange - if it doesn't work I think I'll have to get a MTeor
Anyway - lots of thanks for your work - and giving me back my hope on smartphone ROMcooking

HTC P3600 don't want to flash!

Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!

no ideas guys?

so no one can help me with an idea???

What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.

jackkkkk said:
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
Click to expand...
Click to collapse
it's a P3600

Do a hard reset and flash an OFFICIAL ROM from SD-card

Switch to Des' Crash Proof SPL and try flashing the ROM straight from SD card.
This should work.

thank you very much. I've already tried to change to Des Crash Proof but at about 13%-14% it gives me an error when I reboot by softreset the system is always the same. Is it normal? Is there a specific procedure to change SPL software?

If it works at all after SPL flashing, then you must have followed all procedures. Try flashing Olipro's SPL and scan for bad blocks in flash.

nightblade said:
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
Click to expand...
Click to collapse
Make sure that your SD card it out

Help me for updating ROM for HTC Touch HD

Hi,
I'm using HTC TOUCH HD (orange). I bought this handset from Scotland it was locked with orange only but i Unlocked this handset in india and now i'm using this handset with vodafone India.
Now this handset works gr8 for me but still i can see some settings are map with orange only. I heard if i update with international English ROM then my problem will get solved.
I have no idea about updating ROM. I read lots of blogs even i read on xda wiki also but not sure as its looks like if i update my ROM then i may lose my original ROM.
I have few question:
1. How to choose correct ROM for my handset.
2. Which is the right tool to take the Device backup.
3. If i'm unable to update with new ROM then will i lose my Original ROM.
Hereby i'm sending you my current ROM Version and release date
Current ROM Version: 1.1961.1 WWE
Operator Version: 34.119.1.611
ROM Date: 11/25/08
Radio Version: 1.09.25.14
Protocol Version: 52.49a.25.26U
Your help will be highly appreciate.
Thanks in advance.

I suggest not doing it. If you can't read and search, then you can't flash a ROM.

hey dear. i also got my handset from UK with locked with orange. If u want to upgrade simply go for Cooked ROM's. Those original rom's are crap and cant use the full potential of ur handset.
I would suggest u go for Energy sense 2.1 21898 version.
u need to do just few things in order to flash a cooked rom. if u r ready then do let me know
the best way to take a backup is using PIM backup software
re ur 3rd question. once u flash a cooked rom u will never want to go back to ur original stock rom.
send me a pm whenever u r ready and confident to flash ur phone
apatni said:
Hi,
I'm using HTC TOUCH HD (orange). I bought this handset from Scotland it was locked with orange only but i Unlocked this handset in india and now i'm using this handset with vodafone India.
Now this handset works gr8 for me but still i can see some settings are map with orange only. I heard if i update with international English ROM then my problem will get solved.
I have no idea about updating ROM. I read lots of blogs even i read on xda wiki also but not sure as its looks like if i update my ROM then i may lose my original ROM.
I have few question:
1. How to choose correct ROM for my handset.
2. Which is the right tool to take the Device backup.
3. If i'm unable to update with new ROM then will i lose my Original ROM.
Hereby i'm sending you my current ROM Version and release date
Current ROM Version: 1.1961.1 WWE
Operator Version: 34.119.1.611
ROM Date: 11/25/08
Radio Version: 1.09.25.14
Protocol Version: 52.49a.25.26U
Your help will be highly appreciate.
Thanks in advance.
Click to expand...
Click to collapse

it is a real simple process and once u do it u wont fear flashing it again & again

sorry for late reply Thank you so much for ur positive reply.
Could you please let me know from where i can get the currect ROM for my handset?
also please tell me who u did it with ur HTC TOUCH HD and does and don't if you have something before flashing ROM.

OK I have some time so let me try to put it as simple as I can.
First, there are 3 firmwares:
SPL -- This needs to be hacked to be able to change to any ROM
ROM -- You have the HTC official one and cooked ones
RADIO: you have 1.09, lastest are 1.13 / 1.14 / 1.17
The safest way is to use USPL, since it does not modify the SPL. You can always flash a ROM again.
See: http://forum.xda-developers.com/showthread.php?t=462347
Download uspl_2.5.zip
Be aware that some antivirus flag the exe as dangerous, but that's because it contains an exploit for a buffer overflow.
If you're using Vista or 7, you need to change the drivers for HTC USB sync as explained on http://forum.xda-developers.com/showthread.php?t=291723.
Now power off the phone (long press power button)
Press volume down on the side, and power button
That should leave it in the Red/Green/Blue/White screen
Now connect it to the PC and run USPL
It should reboot and go back to the Red/Green/Blue/White screen but now it says USPL
The phone is ready to flash any ROM or any radio now.
Official HTC ROMs here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.3 4_1.13.25.24_Ship.exe
is the last one on the web, it works fine. Does not have the lastest versions of everything but it works fine.
In the forum you have links to many cooked ROMs, based on Windows Mobile 6.1 and 6.5. WM 6.5 takes more RAM and it's slower than 6.1 (like Vista and XP). But most ROMs today are WM 6.5.
I have been used these two in the last months:
http://forum.xda-developers.com/showthread.php?t=460640
http://forum.xda-developers.com/showthread.php?t=648831
The recomendation is to flash the HTC stock ROM first (that will also update the RADIO to 1.13.25.24). Then if you want to experiment, you can flash a cooked ROM.

Well,
My opinion: once you are addicted to ROM, I think HSPL would be the best way.
You can flash a ROM within 5 minutes or less. Also, using task29 is even more easier.
Cheers, my friend.

vcespon said:
If you're using Vista or 7, you need to change the drivers for HTC USB sync as explained on http://forum.xda-developers.com/showthread.php?t=291723.
Click to expand...
Click to collapse
Could somebody tell me in an easy way how to do this? And when do i do it? Do i have to install the old drivers again after flashing? Where can i find the drivers to use, i use windows 7 32 bit
Thank you from Forca

wow you make it very easy for me now this weekend i'm gonna try all this.
I really appreciate your effort to explain me in details. I think its quite easy to do.
vcespon said:
OK I have some time so let me try to put it as simple as I can.
First, there are 3 firmwares:
SPL -- This needs to be hacked to be able to change to any ROM
ROM -- You have the HTC official one and cooked ones
RADIO: you have 1.09, lastest are 1.13 / 1.14 / 1.17
The safest way is to use USPL, since it does not modify the SPL. You can always flash a ROM again.
See: http://forum.xda-developers.com/showthread.php?t=462347
Download uspl_2.5.zip
Be aware that some antivirus flag the exe as dangerous, but that's because it contains an exploit for a buffer overflow.
If you're using Vista or 7, you need to change the drivers for HTC USB sync as explained on http://forum.xda-developers.com/showthread.php?t=291723.
Now power off the phone (long press power button)
Press volume down on the side, and power button
That should leave it in the Red/Green/Blue/White screen
Now connect it to the PC and run USPL
It should reboot and go back to the Red/Green/Blue/White screen but now it says USPL
The phone is ready to flash any ROM or any radio now.
Official HTC ROMs here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.3 4_1.13.25.24_Ship.exe
is the last one on the web, it works fine. Does not have the lastest versions of everything but it works fine.
In the forum you have links to many cooked ROMs, based on Windows Mobile 6.1 and 6.5. WM 6.5 takes more RAM and it's slower than 6.1 (like Vista and XP). But most ROMs today are WM 6.5.
I have been used these two in the last months:
http://forum.xda-developers.com/showthread.php?t=460640
http://forum.xda-developers.com/showthread.php?t=648831
The recomendation is to flash the HTC stock ROM first (that will also update the RADIO to 1.13.25.24). Then if you want to experiment, you can flash a cooked ROM.
Click to expand...
Click to collapse

By the way, I'm back to Topix 3.5 WM6.1 Manila 2.1.
The difference in speed with a WM 6.5 ROM is too big. People should really consider give this one a try and see what I mean. On WM 6.5 even typing in keyboard is slow. Here you start with 37% RAM used, not 52%. And while using Opera, you have 55% RAM used, not 80%.
No way I'm going back to WM 6.5.

ok, I'm closing this thread now. In future could everyone direct users looking for flashing help to this thread.
Thread closed

Help with upgrade to WM6.5

Hi all,
please if someone can help me solve problem.
I got few days ago Touch Diamond2. It has WM6.1 ROM on it. I tried to upgrade with official ROM from htc.com to wm6.5 but it hangs on 18% with error "communication error". Phone turned on in recovery mode. After that i tried flashing with custom roms but no luck again. It hangs on HTC screen when booting and nothing happens. I flashed it back with shipped 6.1 ROM from HTCpedia and it started normal.
When i start it in boot load mode it states 1.33 Olinex SPL. Do i need to put original hardSPL before upgrading to official ROM or there is something else i am missing?
Tnx in advance

Borna_bkpdata said:
Hi all,
please if someone can help me solve problem.
I got few days ago Touch Diamond2. It has WM6.1 ROM on it. I tried to upgrade with official ROM from htc.com to wm6.5 but it hangs on 18% with error "communication error". Phone turned on in recovery mode. After that i tried flashing with custom roms but no luck again. It hangs on HTC screen when booting and nothing happens. I flashed it back with shipped 6.1 ROM from HTCpedia and it started normal.
When i start it in boot load mode it states 1.33 Olinex SPL. Do i need to put original hardSPL before upgrading to official ROM or there is something else i am missing?
Tnx in advance
Click to expand...
Click to collapse
updating your Hard-Spl to HSPL 1.83 first ! in order to flash WM 6.5 rom or custom rom

Hi and tnx for quick answer.
Just to confirm. I need to update even if I want to flash official WM6.5 rom from htc.com?

Borna_bkpdata said:
Hi and tnx for quick answer.
Just to confirm. I need to update even if I want to flash official WM6.5 rom from htc.com?
Click to expand...
Click to collapse
I think it could, try it !

Doesn't the official WM6.5 ROM update include an embedded SPL though? Although if flashing from official ROM to custom ROM or vice versa you'd definitely need to update HSPL.

netrial said:
Doesn't the official WM6.5 ROM update include an embedded SPL though? Although if flashing from official ROM to custom ROM or vice versa you'd definitely need to update HSPL.
Click to expand...
Click to collapse
Please Read Carefully the instruction for installing HSPL 1.83 or better to upgrade it to 2.51.OliNex.Make Sure U Have a internet connection on as hspl needs internet to install.