Related
I know there are others experiencing the 28% death wall while trying to flash WM6, but there doent seem to be any specific solutions to this.
I have a Dopod D810 and has already installed 1.30 olipro. Just trying to flash to the official WM6 ANZ Rom. No luck.
Any suggestions guys?
Should just be a very straight forward procedure. Flashing a Dopod with an official Rom.
should be, but it's not... mine is Dopod asia, and stuck at 28% when flashing. Not too sure, but really seemed to me that it was something related to hard-spl. After the 28% error, i reflashed an unofficial rom and tried the official again.
eventually it worked for me.
i guess you don't technically need to manually enter hard-spl first before flashing official ROM.. if anything went wrong i guess you could send it back to them..
safest is to use a modified RUU so it just flashes ROM without IPL + SPL.. i thiiiiiink problem is something to do with SPL
which unofficial rom did u reflash it to? I've been going back and forth with AX3L_OS v3.0.0.2 and the official ANZ dopod rom.
tried about 5 times now. still trying. each time it fails at 28% it's another 10 minutes to flash backto the unofficial rom.
maybe if i try to trce ur steps exactly it might work.
i was flashing to some pdaviet ROM, but i don't think that would make any difference from ax3l's...
have you tried flashing the official ROM with a modified RUU, or you really want the whole package...
If you're just trying to keep everything official i guess you could try to flash the official rom without manually entering bootloader and take your chances. Being that its an official ROM i guess it's safer, or at least covered in warranty..
One question, why don't you try to flash to official WM5 ROM, then to official WM6.. since technically it's supposed to work that way
seriously, i'm not sure why you'd want the official one though.. it's nothing special
Yeah I've tried flashing back to the official WM5 and then WM6, same story.
Tho I havent tried flashing the official WM6 through modified RUU, mainly coz i dont know how to.
Also, In the AX3L version of WM6, there doesnt seem to be a phonepad input method. only keyboard and block recongniser and one other one. Is that coz it's a modified rom, or does WM6 not have the phone pad input. if that's the case i can forget about flashing to WM6 all together.
can't remember if official wm6 has phonepad, but you can just install a cab for it, so it's not a big deal.
look on my site for a link to modified RUU official ROM... instructions are here
i had a lot of problems being stuck at 28%
what eventually i got it to flash to the aus rom was i used SPL 1.20 then it seemed to flash fine.
for some reason my phone doesnt like any other version of SPL besides the one on the latest aus rom either, i flashed to a cooked rom and couldnt flash back until i had put spl 1.20 back in then flashed back to the aus rom.
I have the same problem with 28% stucking
I try to reflash but I still have the same
do you have hard-spl? if so, which version? If you do, flash back a cooked ROM..
if not, you need to try to flash official ROM..
if neither is working, use splxploit. I think all links you need are in this thread already
I have a same problem.
I was upgraded from WM5 to Hong Kong Official WM6 chinese ROM, then I want to change to Official English ROM, I did the Hard-SPL 1.3 and get the SuperCID, but when upgrading the WM6 English officeial ROM, this was stuck at 28%.
Now I was able to flash back to WM5 rom, but I world like to Upgrade to WM6 official ROM, anyone help?
I had this problem when upgrading to the Australian WM6 official HTC Release. The way around it is to run the Trinity Service Provider & CID unlock program from the link below. Dont know why but to use either release, Dopod or HTC WM6 you must run this tool first.
ftp://xda:[email protected]/Trinity/Tools_and_Programs/HTC_Trinity_SIM_CID_Unlock_v1.zip
Hope this helps
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
HI, Thank for your reply, how can I do the modified RUU?
Hi all,
I have success to flash the WM6 official ROM.
this is my experience:
To flash the Radio ROM first, I has flash the 1.50.08.11 Radio ROM.
Then to download the Dutty NBH Tool to take off the Radio DOM of WM6 official ROM.
Then to flash the modify ROM.
Now, my phone is running WM6.
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
Learn something new everyday. Never knew that simply modifying the RUU would itself allow the updates. Just tried it, and yes it works also.
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
how do mofify the RUU? and what do I modify it to?
thanx walterjm
Can you share HK-CHT rom for noSPL noIPL noRadio ? Thanks!
WildsideUK said:
I had this problem when upgrading to the Australian WM6 official HTC Release. The way around it is to run the Trinity Service Provider & CID unlock program from the link below. Dont know why but to use either release, Dopod or HTC WM6 you must run this tool first.
ftp://xda:[email protected]/Trinity/Tools_and_Programs/HTC_Trinity_SIM_CID_Unlock_v1.zip
Hope this helps
Click to expand...
Click to collapse
Can you share HK-CHT rom for noSPL noIPL noRadio ? Thanks!
I had the same problem and I resolve it by extract the rom and re-build it ... look at the thread http://forum.xda-developers.com/showthread.php?t=327667
Good luck
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
no ideas guys?
so no one can help me with an idea???
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
jackkkkk said:
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
Click to expand...
Click to collapse
it's a P3600
Do a hard reset and flash an OFFICIAL ROM from SD-card
Switch to Des' Crash Proof SPL and try flashing the ROM straight from SD card.
This should work.
thank you very much. I've already tried to change to Des Crash Proof but at about 13%-14% it gives me an error when I reboot by softreset the system is always the same. Is it normal? Is there a specific procedure to change SPL software?
If it works at all after SPL flashing, then you must have followed all procedures. Try flashing Olipro's SPL and scan for bad blocks in flash.
nightblade said:
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
Click to expand...
Click to collapse
Make sure that your SD card it out
I've tried to download the ROM, but HTC tell me this "Sorry, this software download is not suitable for your device".
Maybe my device s/n number is not correct.
Maybe someone who has the correct s/n could download this ROM~
Just tell you guys the news~
http://www.htc.com/europe/SupportDownload.aspx?p_id=174&cat=2&dl_id=537
Caxio's and frednd's DownLoad Link--(I wanna say THANK YOU VERY MUCH!)
See page3 #21 & #23
Filename is :
HTC Touch 3G_MR2009_RUU_Jade_HTC_Europe_2.32.401.2_Radio_Sign_12.41.30.16_0.41.30.12_Ship
edit:
on booting the last red line (after radio and protocol) now says :
D 2.32.44800
Date (which shows after first boot) after screen calibration is now set to 25/03/09
(in settings / about) Build : 5.2.20771 (20771.1.4.6)
(in settings / device info) : rom version 2.32.401.2(44800)
ON customization after first boot if scaned for wifi networks and poped up a message about available networks
Ht845kh14923 :d
o2p63 said:
Ht845kh14923 :d
Click to expand...
Click to collapse
This is for italian version.
Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??
Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??
It seems HardSPL 1.40oli and this 2.32 rom don't work very well.Very sluggish and phone can't turn ON even after 2 Hard resets.
What is your experience???
Do not install if hard spl
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Could anyone check, if the gps-support has been improved?
km
lexx2009 said:
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Click to expand...
Click to collapse
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
update : Jade is fine now. New SPL is 2.32.0000 . More testing to be done.
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
lagoskon said:
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
Click to expand...
Click to collapse
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Myster said:
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Click to expand...
Click to collapse
This is on the Hard-SPL page along with the Oli version
http://forum.xda-developers.com/attachment.php?attachmentid=166262&d=1236988725
GPS seems to work fine now, also the scroll behavior of opera is better
km
It is annoying that hardspl doesnt work with this upgrade of jade.. can't built a rom now with the new oem. It's all newer than the iolite versions, but still doesnt include Footprint
Any changes in Manila? New tabs? Calendar? Stocks? Changes in the contacts?
Hi
What is the Radio version in this new ROM?
I have just applied the version from here and if this contains the old Radio then I can hold off for now until hopefully a compliant Hard-SPL is made, I can live without Opera being perfect.
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
nereus114 said:
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
Click to expand...
Click to collapse
Install a different rom from this forum-> Shut down your jade, unplug it. Hold down "volume down button" and ""power on button" to get in to boot mode. now start to flash another rom.
when finished you can install stock spl and then install this new rom
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
jarel said:
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
Click to expand...
Click to collapse
that's right.. but i think it's in one of the drivers. using the old drivers and the new oem/sys makes it possible to run it with the current hardspl.
radio in this rom 0.41.30.12
no changes in manilla tabs, don't know what changed but it's newer
Good morning,
im opening a new thread because i didnt find an answer for my problem.
I got my Blackstone running with HSPL1.56+ olinex, 1.17 radio and using different roms like dutty or miri ones... so everthing works fine since I tried to flash the new dutty rom holy grail R2... after that my screen s displsaying the colours wrong like in 256colours graphic. some colours like green and purple are flickering...
I tried to change from HSPL to USPL but it wont help...moreover i flashed the USPL and flashed with 1.56 stock rom without success
dont know what to try
thanks in advance
zwon
Mybe a coincidental hardware problem... but just a guess!
Use my mobiler and see what the phone looks like on your PC?
or is it wrong rom... i gess is about grafick try to put out batery thehn back turn on then when boot do soft reset i have smilary problem
afr33s said:
Mybe a coincidental hardware problem... but just a guess!
Use my mobiler and see what the phone looks like on your PC?
Click to expand...
Click to collapse
i think so too
hm on my pc its looking good...
gagi75 said:
or is it wrong rom... i gess is about grafick try to put out batery thehn back turn on then when boot do soft reset i have smilary problem
Click to expand...
Click to collapse
i think not because i flash roms which i got working before
take out battery i tried a few times...last night my hd had no batt^^
i wos instal ok rom but each time when i do reset he goes off he wont start then i remove batery off then put back and start he goes up then when i see on screen smart mobilty is write tu soft reset and is ok all.i have thet problem and solwed...do what i do meybe help
sory for english
Update your hardspl to version 1.56
Does your SPL match rom, i.e. if a rom based on 1.56+ you need HSPL 1.56
Fallen Spartan said:
Does your SPL match rom, i.e. if a rom based on 1.56+ you need HSPL 1.56
Click to expand...
Click to collapse
yes i tried... flashed the hspl 1.56+ before and using it with the equal spl version but wont fix my screen
i tried a many different solution but nothing would solve it
flash to stock rom, revert spl to stock and reflash stock rom.
use the newest stock rom available, after that HSPL again and everythings good to go.
have a look at the wiki, the problem is described pretty well.
regards
meska said:
flash to stock rom, revert spl to stock and reflash stock rom.
use the newest stock rom available, after that HSPL again and everythings good to go.
have a look at the wiki, the problem is described pretty well.
regards
Click to expand...
Click to collapse
sure? than sorry.. dont saw it
ill give it a try
meska said:
flash to stock rom, revert spl to stock and reflash stock rom.
use the newest stock rom available, after that HSPL again and everythings good to go.
have a look at the wiki, the problem is described pretty well.
regards
Click to expand...
Click to collapse
how to revert to stock spl?
ok find it by myself....would 1.54 be recommend or later? or could you even post the url where i find this in wiki??
dont find it
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Rom156
have a look under the greenscreen section... 1.54 will just be fine.
Options if you have Olinex 1.14 HSPL installed then installed a 1.56 rom and now have greenscreen
* (Not recommended) Revert back to stock SPL (using Restore-SPL-1.xx from HSPL thread)
* Update HSPL to 1.56 (After flashing HSPL 1.56 your device will reboot and the greenscreen problem is gone.)
* Or Use USPL 2.5
or send me a PN i can help you via ICQ even in german.
regards
meska said:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Rom156
have a look under the greenscreen section... 1.54 will just be fine.
Options if you have Olinex 1.14 HSPL installed then installed a 1.56 rom and now have greenscreen
* (Not recommended) Revert back to stock SPL (using Restore-SPL-1.xx from HSPL thread)
* Update HSPL to 1.56 (After flashing HSPL 1.56 your device will reboot and the greenscreen problem is gone.)
* Or Use USPL 2.5
or send me a PN i can help you via ICQ even in german.
regards
Click to expand...
Click to collapse
so i tried this with all 3 kinds of stock spls...1.54 even too but it wont work
seems to me as it would be an other problem as the Greenscreen issue
yeah would be nice if you could help me with that tomorrow
ill add u in icq
hi
i thought that wm6.1 is faster than wm6.5 so after hardspl flash my new topaz with wm6.1 rom but it didn't start .after soft flashing and rest just shows startup picture and restart again .so i had to reflash it to wm6.5.
the question is how can i use wm6.1 and???
thanx in advanced
farzad23 said:
hi
i thought that wm6.1 is faster than wm6.5 so after hardspl flash my new topaz with wm6.1 rom but it didn't start .after soft flashing and rest just shows startup picture and restart again .so i had to reflash it to wm6.5.
the question is how can i use wm6.1 and???
thanx in advanced
Click to expand...
Click to collapse
I think you would need to downgrade your SPL.
So you would need to reinstall SSPL, then just install HSPL 1.83, then the 6.1 ROM. You will probably have "commercial use" issues to reinstall 1.83 so I would send the Olinex team an e-mail first before trying.
thanx Bruce Inman for u'r reply.i'm waiting for
hi Bruce Inman
I did what you said before.downgarde hard spl to 1.8 ver and then flashed my topaz with wm6.1 cocked and stock but didn't work. in boot session reboot cycling occur.
downgrading spl is not necessary i think, because i have also downgraded 6.5 to 6.1 last week, and my topaz got the latest hspl. last year i downgraded my kaiser to 6.0 and 6.1 with the latest spl.
i think the rom image you acquired is damaged, try re-downloading it
@Carrier
hi
i tested many rom cocked and stock .when i bought this damn topaz it was wm6.5
i think all fu... HTC are slow ,unstable .
I tried the same my self with official ROM from HTC. I didn't have to downgrade SPL because my phone for some reason is unable to be flashed HSPL Olinex ??
Operation run smoothly but after finishing topaz entered a constant reset loop after boot screen
I run out of ideas ...