Hi guys, I recently fell into the sea by accident and my phone was in my pocket and it got wet. I did not know what to do and i thus took out everything and wiped it dry and then plugged it into a power source. No response. After a few tries, it started vibrating madly and the light on top of the device started flickering. The phone started heating up like mad until finally i switched off the power supply. Now it is not giving any response. Please Help!!!
you fried the board.
In future if you ever get a phone/anything electronic wet, immediately remove the power source (battery) and leave it to dry in a well ventilated place for a long time (or a bag of dry rice, which can draw the water out). And when you think it's dry, leave it a bit longer still!
Don't be curious and try turning it on "to see what the damage is", as you will invariably cause more damage.
Unless it's tap water that's spilled on it (or it's been submerged in) you will likely want to wash it out before drying it - pure, deionised water is good for this. This might seem mental, but it's not - pure water is generally harmless to electronics unless there's current running through them. The residue from dried seawater or coffee will cause short circuits and damage the thing, so best to wash it off.
Spideyrocks said:
Hi guys, I recently fell into the sea by accident and my phone was in my pocket and it got wet. I did not know what to do and i thus took out everything and wiped it dry and then plugged it into a power source. No response. After a few tries, it started vibrating madly and the light on top of the device started flickering. The phone started heating up like mad until finally i switched off the power supply. Now it is not giving any response. Please Help!!!
Click to expand...
Click to collapse
Seawater? Ouch. If anything salt will kill the motherboard faster than the water. But yes, you made a mistake by plugging it into a power outlet after drying it out. Next time (which hopefully does not occur), pull out the battery, dry it out, and stick it in a bag of rice or silica gel packets. Waiting a few days before touching it would also be a good idea. You may be able to try this now and to rid of the salt, soaking the phone in 100% rubbing alcohol (only 100%!) may clean out the internals. Good luck!
By the way, I haven't tried out the alcohol method but it was suggested by other forum members. The worst case scenario with the alcohol is that some of it seeps into your screen and won't evaporate, so try out the rice first.
It's a common misconception that water conducts electricity. In fact, it's salt water that conducts electricity. The problem is our skin has minute amounts of salt on it. It has been tested already making a completely water submerged PC as an advanced cooling method such as using cooking oil. The plus side is for circulating, water isn't as thick & flows faster plus it don't "go bad". The downside is you have to be very careful not to let salt get into the water & how hard it is to find "pure water".
P.S. DO NOT TRY IT YOURSELF. Even Mineral Oil can be dangerous to PC parts if you don't know what you are doing, plus Oil dissolves rubber & plastic parts over time.
drkfngthdragnlrd said:
It's a common misconception that water conducts electricity. In fact, it's salt water that conducts electricity. The problem is our skin has minute amounts of salt on it. It has been tested already making a completely water submerged PC as an advanced cooling method such as using cooking oil. The plus side is for circulating, water isn't as thick & flows faster plus it don't "go bad". The downside is you have to be very careful not to let salt get into the water & how hard it is to find "pure water".
P.S. DO NOT TRY IT YOURSELF. Even Mineral Oil can be dangerous to PC parts if you don't know what you are doing, plus Oil dissolves rubber & plastic parts over time.
Click to expand...
Click to collapse
Are you joking? Water conducts electricity. Distilled water (saltless) conducts electricity. Mineral Oil != water! And it does not conduct electricity (the pc cooling projects).
beaups said:
Are you joking? Water conducts electricity. Distilled water (saltless) conducts electricity. Mineral Oil != water! And it does not conduct electricity (the pc cooling projects).
Click to expand...
Click to collapse
You may be right that distilled/Pure water conducts electricity, for that matter everything conducts electricity if enough voltage is applied. Even air as proof by Lightning. Computers run on 12/5 Volts though (except the Power Supply that turns 220/110 Volts into 12/5 Volts). This is not enough voltage (the 12/5 Volts) to pass through Pure Water. The point is people have tried it & it works. Would I recommend it to someone, NO. As I said, any contaminants will increase water's ability to conduct electricity. There's parts in the PC that can give off salt & other contaminants into the water. Our devices work on less than 5 Volts. If you take the battery out immediately & let dry out completely. You can save the device. I've done it myself & helped others save their doing this. The best choice for a advanced cooling system is this 3M liquid, but it's extremely expensive.
beaups said:
Are you joking? Water conducts electricity. Distilled water (saltless) conducts electricity. Mineral Oil != water! And it does not conduct electricity (the pc cooling projects).
Click to expand...
Click to collapse
Excuse me, Distilled water has no free ions which are found in normal tap water (minerals, K, Na, Mg, F) that's why it won't conduct electricity, but as " drkfngthdragnlrd " said at extreme voltages not currents, it totally can and that's what's exhibited in stun guns for example where air itself connects..
Related
hey i have an htc dream that was just recently dropped into a cup of malibu. The phone turns on but it has entered safe mode. Well sometimes its in safe mode. i think the power key is messed up cuz it thinks im holding it down and keeps poppin up the phone options. i dont know what to do or if this can be fixed. please help
The best procedure for dealing with phones falling in liquid is to remove the battery immediately and let it dry completely.
What kills phones is not the liquid as such, but trying to use them while still wet, the current supplied by the battery causes what is known as 'dendritic growth' between the end caps and pins of the many surface mount components, and in the process can actually strip the metal off, leaving a greyish fuzzy deposit.
Plain water is actually not that bad, but sugary liquids, such as fruit juices, or carbonated drinks are the worst, followed by alcoholic drinks, beer, coffee, tea, etc.
If you do spill or drop you phone in anything other than water, you may still have problems, since the residues will be water soluble, and even condensation or high humidity may cause issues.
If it was my G1, ( I don't have one, yet...), then I would completely strip it, and wash everything except the lcd screen, in warm soapy water, then rinse in clean cold water, followed by at least 3 hours in an oven at 60-80 degrees Celcius to dry it off.
The above procedure may save your phone, but it's not a task for anyone not used to disassembling phones, be aware that it will void any warranty you have, and that it is possible to completely kill your phone this way, ( although leaving it with malibu in it will also do that eventually).
I actually read a post, on lifehacker.com I believe, that stated you could submerse the phone into a bowl filled with dry (uncooked) rice... Do not know if it works, but I intend on trying it if my phone decides to take a bath... Could not hurt...
L8r
Open it up, take out the battery and stick it in a bowl of dry rice for a day or so. Don't try to use it while it's wet.
Dry rice will certainly help remove any water, it may leave some water soluble residues, such as sugars etc, which will become 'active' when exposed to a humid atmosphere, the dry rice solution is perfect for water, but may not be as good for other liquids.
Hi,
The water proof feature is nice. However, I prefer sea water for snorkeling etc. So given corrosiveness of salt it's probably not a good idea.
Still from many reports people seem to have it surviving even salt water submersions when not too long and rinsing it immediately afterwards with fresh water.
But i don't want to dessctroy my nice Z3C obviously, so been looking for intermediate solution, like sealed zip bags or so, that would prevent it from too much wate rcontact, and if it leaks or whatever, it will still not die.
Any idea what could be used , if possible not too big to fit the Z3, and still let take some pics?
The phone is not rated for salt water, so I wouldn't want to try it. Salt water splashes from waves are probably fine.
I also wonder if Sony has a way of telling if salt water got in the phone should you have to send it in for warranty service. Plus, it's also gonna be much easier to inadvertently exceed the depth rating in the ocean. Definitely best to get a dry bag of some kind IMO.
Something like this: http://www.bhphotovideo.com/c/product/1035195-REG/loksak_lok_alok3_4x7_3_aloksak_bags_4_5x7.html
Or this: http://www.amazon.com/FRIEQ®-Universal-Waterproof-Carrying-iPhone/dp/B00AW2QT8I/ref=pd_cp_sg_0
There are a ton of waterproof phone cases/bags out there. Just be sure to pick one that promises super-clear plastic for photos.
Please use the questions and answer sections for questions you want answered
Thread moved
Sorry for wrong forum and thanks for moving it.
I finally ordered one of these: http://www.amazon.com/dp/B00AW2QT8I/ref=pe_385040_121528360_TE_dp_1
Will see how it works with the Z3C
Excuse me... Why should the Z3C not be waterproof in saltwater???
I really cannot see the problem? It is not that saltwater is more wet than "normal" water...
The saltwater will leave some salt when it is dry but you could easily remove this by putting the Z3C in water without salt for some minutes...
I don't believe the salt will do much good to the oliphobic coating of the screen or audio connector.
We are talking about 30 minutes of contact with salt...? To play it safe you use it in salt water for 20 minutes and then put it in normal water for 5 minutes and all the salt is gone...?
And by the way are both the power button and the audio connector made of aluminium...? And why would salt ruin the oliphobic coating of the screen...?
I could understand if pool water with chlorine could do something to the screen but since Sony advertise that you can use it in the pool then that shouldn't be a problem...
Salt is more corrosive unlike chlorine
cyphomatic said:
Salt is more corrosive unlike chlorine
Click to expand...
Click to collapse
In contact with iron, yes...Plastic, glass and aluminium, no - not for a 30 minute contact...
Foxhunter123 said:
In contact with iron, yes...Plastic, glass and aluminium, no - not for a 30 minute contact...
Click to expand...
Click to collapse
Indeed, I believe that the audio connector might be a weak spot. It sure isn't aluminum. I had other waterproof equipment before with an audioconnector that came into contact with seawater, wich turned out very bad. I won't take a chance.
I will try my Z3c within a week or so when I'm in the Canary Islands.
Have used my previous phone, Xperia ZR, in saltwater many times. No problem at all!
Dont do it. The water proof is only for freshwater.
You may want to read this page : http://support.sonymobile.com/global-en/xperiaz3compact/dm/water-and-dust-resistance/
Never immerse your device in salt water or let the micro USB port, headset jack or other uncovered parts come into contact with salt water. If you’re washing dishes by hand, avoid letting your device come into contact with the detergent or any other liquid chemicals.
Click to expand...
Click to collapse
If your Sony smartphone or tablet is waterproof to IPX8 standard*, then you can use it in a chlorinated swimming pool. However, avoid keeping the device in the pool for too long and remember to rinse it off thoroughly with fresh water once you get out.
Over time, chlorinated water can corrode the rubber seals, so prolonged use in chlorinated water is not recommended. But if you want to use your device to get underwater close-ups of a spectacular dive or your child’s first swimming lesson, go ahead.
Click to expand...
Click to collapse
Apart from the fact that Sony says don't immerse the phone in salt water, common sense suggests the copper contacts of the mag charger and headphone jack will not fair well (salt water will leave a nice oxide layer on both, which will impact the conductivity). A few minutes and very careful cleaning of the jack (not just a quick rinse) will probably be OK, but then we also have no idea how the glass coating, camera lens coating and various waterproofing membranes will fair in salt water. Knowing the corrosive nature of salt water and Sony's warning I certainly wouldn't risk dunking it in the ocean. YMMV
There was one story of a z2 that survived after being submerged for 6 weeks in salt water
http://www.phonearena.com/news/Sony...g-submerged-in-salt-water-for-6-weeks_id59223
I've used both my previous Z1 Compact and now my Z3 Compact in saltwater, not an issue at all.
Just pour some fresh water on it afterwards.
Blue grotto, long swim from gradola. no problem later
Use a condom, tie a knot waterproof
pakjebakmeel said:
Use a condom, tie a knot waterproof
Click to expand...
Click to collapse
For playing safe, you should use one of those waterproof bags for smartphones if you want to take your phone for dives in salt water so necesserily.
You would normally be right
Foxhunter123 said:
Excuse me... Why should the Z3C not be waterproof in saltwater???
I really cannot see the problem? It is not that saltwater is more wet than "normal" water...
The saltwater will leave some salt when it is dry but you could easily remove this by putting the Z3C in water without salt for some minutes...
Click to expand...
Click to collapse
However, the frame is aluminium, which doesn't play nice with salt water.
Hi guys
My phone was dropped in the water. I gave time to it and make it dry by hairdryer and put it in rice to absorb its humidity. Then I opened the back panel and made it drier. INow when I press the power button nothing happened. Just when I connect it to the charger, the charging logo and then start screen appear and shows 1 percent charge, is charging and then disappear. it repeats without starting normally. What is your remarks folks?
Something is shorted, just send it to someone to fix it and tell them it's water damage.
Disconnect the battery immediately.
Rice does nothing.
Get some anhydrous (99%) isopropyl alcohol* and liberally flush the entire phone with it to absorb the moisture.
Use low pressure compressed dry oil free air to blow out as much of the alcohol as possible.
Do it in a dry room and it is flammable.
After you get it as dry as possible allow to dry in a warm, dry room with a fan on it.
Let it rest for at least several days.
Reconnect the battery and see what you got.
* never use isopropyl alcohol or any solvent around an LCD display, it will poison it. Should be safe for AMOLED displays. Try to prevent it from getting in between the display and the glass if that can happen.
Use your best judgement.
The more you can safely disassemble it before flushing it out the better. Be aware that individual assemblies like the display and mobo are sensitive to ESD damage when out of circuit.
In a dry room handling them is risky if you disconnect the ribbon cables. Unfortunately this is exactly where water tends to get trapped.
If you disassemble to subassemblies level raise humidity in the room to 50% and use a plain wood surface, or earth grounded ESD mat to work on. A ESD wrist strap is highly recommended.
It may be best not to remove the ribbon connectors other than the battery, flush it well, and allow more drying time.
Either way you want to dry the assembly in a warm dry remove to remove all residual moisture; it must be completely dry before powering up again.
If any corrosion formed as a result of the water exposure especially with the battery connected it will not be salvageable.
Lol, that sounds more complicated than having a heart transplant.
vuittion said:
Lol, that sounds more complicated than having a heart transplant.
Click to expand...
Click to collapse
Well once you get a device wet, speed and appropriate actions make the difference between a paper wieght and a working device.
At least I gave known good advice*. Manufacturers won't even attempt to salvage them because experience has shown it's not worth it.
*dropped my Buds case in a full coffee cup (cream/sugar). Immediately pulled it out and apart. Flushed first with RO water to dissolve any sugar then flushed with anhydrous isopropyl.
A day later it was charging again. 2 years later it still works. And that was with the battery in it.
The coffee was still drinkable too
so i just got my xperia 1ii today, i was wiping the screen with a bit of wet cloth before sticking on the screen protector, then i saw mist on the front facing camera, next thing i know it screen starts to flicker and turn green, then it died, it was a sad day for me, is it possible for water to get in an ip68 phone when brand new?
it was also kinda my fault for using wet cloth, but like all my other ip68 phones this never happened to me T _ T
WYSIWYG... yes it's possible.
Never assume the seals are intact. Protect from water exposure at all times is what I do.
Will Sony warranty cover it???
I am not sure about Sony's warranty on user error.
There is nothing in the box stating anything about warranty. I bought it online but there is a physical shop that I collected the phone from.
I left it in a bag of rice for 10 hours but the screen still turn up black screen with some odd lines and shut itself down, I feel so dumb for causing this, I usually do the same way of installing screen protectors for my Z3+,Z5 and XZ and water never got in, I feel so embarrassed and unlucky T_ T
Rice Doesn't Work!
The phone needs to be powered down and the battery disconnected asap. Otherwise it will likely be destroyed if it isn't already. It needs to then be completely dried out.
-or-
Battle it out with Sony.
Obviously the first option is incompatible with the second option. I'd send the mess back to Sony, they may or may not suck it up easily.
Sony is a pain to deal with...
blackhawk said:
Rice Doesn't Work!
The phone needs to be powered down and the battery disconnected asap. Otherwise it will likely be destroyed if it isn't already. It needs to then be completely dried out.
-or-
Battle it out with Sony.
Obviously the first option is incompatible with the second option. I'd send the mess back to Sony, they may or may not suck it up easily.
Sony is a pain to deal with...
Click to expand...
Click to collapse
Sony is hard to deal with, ya so I've heard, too bad stores are not open today or tomorrow need to wait till Monday.
damn it I bought rice for nothing.
SinclairLen said:
Sony is hard to deal with, ya so I've heard, too bad stores are not open today or tomorrow need to wait till Monday.
damn it I bought rice for nothing.
Click to expand...
Click to collapse
I know Sony well, as I have torn into them multiple occasions. They are rotten to the core.
That however doesn't mean that a loose chainsaw can't find an artery
I'm one of the few customers who's gotten a refund check and spoke with a VP in Teterboro NJ. They are slime... the VP's are the worst; a midlevel manager is more likely to help you if you slip through one of the cracks in customer support.
If they take back without trouble, fine.
Otherwise better buckle up Dorothy, it's going be a rough ride.
Did you use a MC or Visa to make the purchase? If so you got leverage...
Send unit back for refund of replacement and do a charge back through the bank.
Do you want another? If not be clear you want a full refund.
Here's the thing I live in Malaysia, I bought it online, and these guys are a small retail start-ups.
They Imported the device from Hong Kong cause we are kinda short on phones that are price above $600. Malaysians don't really spend much on buying new phones hence the difficulty to find high end phones locally, especially Sony, not a popular pick in recent times.
Visa here doesn't even provide any leverage hahaha.
would try to send it back to their local store tomorrow.
I would actually like to get replace to be honest, but some how I have doubts in my mind saying that its gonna be super thought ride.
Have the rear cover removed, disconnect the battery*. Is there visible water in it?
Get out as much as possible.
You need a warm, dry room. Lay on side with a high volume fan on it. Let sit for a couple days.
If you can get anhydrous isopropyl alcohol** carefully flush with that to remove the water. Use care as if it gets between the glass and display it will leave a water mark. Then dry as above.
All connectors, everything must be 100% dry before you reconnect the battery. The room must be dry, heat drives out moisture; use a hot box if you must. Keep temperature under 110F. This may save it...
*the sooner the better.
** never use methanol or isopropyl that isn't at least 96% alcohol. Never use any solvent including isopropyl alcohol with LCD display, it will poison it!
I don't dare to remove the back cover, wont that void the warranty?
I think water got in the LCD connectors, cause last time I turn it on I has weird flickering and turns green with vertical lines.
SinclairLen said:
I don't dare to remove the back cover, wont that void the warranty?
Click to expand...
Click to collapse
Yes it might.
That's a AMOLED display not a LCD...
I got some silica gel put in an air tight jar, its been sitting over night since yesterday, hope it turns on tomorrow, or else I am gonna feel so awkward when I bring it to their store.
Damn I've never brought a Xperia phone or any phone in for water damage or any sort of claim warranty before, its giving me the shakes.
SinclairLen said:
I got some silica gel put in an air tight jar, its been sitting over night since yesterday, hope it turns on tomorrow, or else I am gonna feel so awkward when I bring it to their store.
Damn I've never brought a Xperia phone or any phone in for water damage or any sort of claim warranty before, its giving me the shakes.
Click to expand...
Click to collapse
That will do nothing. Do Not power it up.
[UPDATE]
So I brought it to the store, there was a bit of resistance there, but in the end they allow me to bring it back in for a check.
They say hopefully there is no red on the water damage sticker, cause if there is, they cant help, but if its just faulty they can replace the phone.
blackhawk said:
Yes it might.
That's a AMOLED display not a LCD...
Click to expand...
Click to collapse
Sony use since xperia 1 an Oled display and not Amoled.
blackhawk said:
That will do nothing. Do Not power it up.
Click to expand...
Click to collapse
You'd be surprised at what silica dessicant beads can do.
V0latyle said:
You'd be surprised at what silica dessicant beads can do.
Click to expand...
Click to collapse
Heat drives out moisture. You need air circulation as well for best results. With a sealed phone that isn't going to cut it.
First any free standing water needs to be dumped out... that's sort of funny, but true.
If you every dealt with flood damaged cars the magnitude of the problem becomes clear. Powered on circuits can be damaged irreparably in a short amount of time. A lot depends on the conductivity of the water and how long it sits there. If the battery was disconnected the car may be salvageable.
blackhawk said:
Heat drives out moisture. You need air circulation as well for best results. With a sealed phone that isn't going to cut it.
First any free standing water needs to be dumped out... that's sort of funny, but true.
If you every dealt with flood damaged cars the magnitude of the problem becomes clear. Powered on circuits can be damaged irreparably in a short amount of time. A lot depends on the conductivity of the water and how long it sits there. If the battery was disconnected the car may be salvageable.
Click to expand...
Click to collapse
Heat can help but the point is to make the air inside the bag extremely dry. Air readily absorbs moisture, which eventually evaporates. Very true about keeping everything turned off; while deionized water is non conductive and won't bother anything, most accidental spills and drops are in contaminated water which not only can be conductive, but may leave behind trace elements as it evaporates.
Still, I've had quite good success with desiccant rescue bags.
V0latyle said:
Heat can help but the point is to make the air inside the bag extremely dry. Air readily absorbs moisture, which eventually evaporates. Very true about keeping everything turned off; while deionized water is non conductive and won't bother anything, most accidental spills and drops are in contaminated water which not only can be conductive, but may leave behind trace elements as it evaporates.
Still, I've had quite good success with desiccant rescue bags.
Click to expand...
Click to collapse
I've cleaned thousands of circuit boards over to remove the flux. Sticking them in a sealed container with dry air is one thing I never did to dry them. Anhydrous sopropyl alcohol is an excellent cleaning/drying agent for most electronics, but needs a dry room to avoid condensation as it evaporates. Dry warm/hot air with high air flow is best for both isopropyl and water. Most times I also used compressed air to knock off the solvent/water beads then dry the pcbs. A high air flow blower of a large shop vac was another favorite for drying them.
Heat drives out moisture ie hot box. Hot boxes have been used for over a century especially in humid climates to preserve surgical instruments, camera equipment and electronics. Works regardless of the outside humidity. The box or cabinet is sealed but not completely air tight.
The surgery room at Pennhurst actually had it's surgery instrument cabinets lined in the back with steam heated radiators, circa about 1900.
They had large glass doors.
You could vacuum dry it though as this be very effective but again the cover should to be removed at the minimum. It's easy to make a small vacuum chamber, the vacuum pump doesn't need to pull a high vacuum to work well at a warm temperature.
Desiccant bags are best used to keep sealed items dry rather than to remove water per se.
I use them to protect lens.
As for the conductivity of the water it's a crap shoot. It could be mixed with sweat, be acidic, or otherwise contaminated.
I used RO water to flush my Buds case when it fell into a full cup of coffee, cream and sugar. The RO water to chase the sugar, then anhydrous isopropyl alcohol to chase the cream and water. Allowed it to dry in the sun and in a room for a day with the spot welded battery in it. I had the case torn apart and flushed within 5 minutes. 2 years later it still works normally. I drank the coffee after I cleaned the case, perfect day
Silica gel works to a degree on my phone, the screen was able to turn on with the start-up logo but as soon it turns on it restarts itself.
I guess two day wasn't enough, especially on phones that are partially sealed, but I guess its true, not all phones are made equal when it comes to waterproof, I remember my XZ was completely waterproof, the swimming pool kind of waterproof.
Its like buying a lottery when you get a phone that fails its waterproof.
still waiting for update from the seller hahaha.
My Samsung mobile phone has fallen into the water because of my fault. But soon after I took it from the water I turned it off. Since I have never faced a situation like this before I searched for some instructions using the internet on my laptop. While searching on the internet I found some directions to solve this and save my phone. But after following those steps still, the phone won’t turn on. To fix this phone,
Soon after I took the phone from the water I put it in a rice bag to remove the water inside it (Nearly 24 hours).
De-assembled the phone as I can (It has a non-removable battery)
Put the phone inside a rice bag for 6 hours and tried again.
But the phone won’t turn on. Is there any other way I can fix this phone? Or should I take this to a repair station?
Rice does nothing.
Pull the battery asap. The phone must be completely dried before connecting the battery again. Pull the rear cover, disconnect the battery and place on side in a warm/hot, dry room with strong fan on it. Give it at least 3 days.
blackhawk said:
Rice does nothing.
Pull the battery asap. The phone must be completely dried before connecting the battery again. Pull the rear cover, disconnect the battery and place on side in a warm/hot, dry room with strong fan on it. Give it at least 3 days.
Click to expand...
Click to collapse
Thank you. It has a non-removable battery but I will follow the rest of the instructions.
maxsam321 said:
Thank you. It has a non-removable battery but I will follow the rest of the instructions.
Click to expand...
Click to collapse
You're welcome.
You disconnect the battery via it's ribbon cable.
Even when powered off there are circuits that have power going to them. This current exacerbates the corrosion and destruction of key circuits.
Anhydrous isopropyl alcohol (>96%) can be used as a drying agent. LCDs displays can be poisoned by any solvent, do not use on LCDs.
Flush liberally with isopropyl alcohol then get as much as possible off the assemblies as fast as possible in a dry room. Isopropyl alcohol is very hydroscoppic and will grab moisture out of the air, it also cools as it evaporates, attracting any moisture in the air. It is flammable...
After doing this allow to dry for 2-3 days as described in previous post.
Avoid getting the alcohol between the display and glass as this would leave a residue stain. Use best judgment... only use anhydrous isopropyl alcohol not methanol!
blackhawk said:
You're welcome.
You disconnect the battery via it's ribbon cable.
Even when powered off there are circuits that have power going to them. This current exacerbates the corrosion and destruction of key circuits.
Anhydrous isopropyl alcohol (>96%) can be used as a drying agent. LCDs displays can be poisoned by any solvent, do not use on LCDs.
Flush liberally with isopropyl alcohol then get as much as possible off the assemblies as fast as possible in a dry room. Isopropyl alcohol is very hydroscoppic and will grab moisture out of the air, it also cools as it evaporates, attracting any moisture in the air. It is flammable...
After doing this allow to dry for 2-3 days as described in previous post.
Avoid getting the alcohol between the display and glass as this would leave a residue stain. Use best judgment... only use anhydrous isopropyl alcohol not methanol!
Click to expand...
Click to collapse
Ok, I will follow these instructions. Thank you for the help.
maxsam321 said:
Ok, I will follow these instructions. Thank you for the help.
Click to expand...
Click to collapse
You're welcome.
Bare in mind there are BGA chipsets in this phone as in most. Water can seep under the chipset and will take longer to dry. The connectors can also retain water and take longer to dry. Place on side to help in draining.
Low pressure compressed dry oil free air can be used as well, but carefully. A shop vac blower... carefully. This can also created an Electro Static Discharge hazard though. Don't touch the phone and nozzle or vac at the same time. Dry air raises the risk of ESD damage. Earth ground yourself before touching the phone; a ESD mat and wrist strap are preferred. Be aware of this hazard. Generally in circuit assemblies are relatively well protected. Points on the mobo can lack input protection and it's best not to touch them.
Heat drives out moisture ie hot boxes that are still used in humid climates to provide a dry environment for humidity sensitive equipment. Up to 120F is perfectly safe for drying. Don't expose the display to direct sunlight to speed drying though. Good luck.
blackhawk said:
You're welcome.
Bare in mind there are BGA chipsets in this phone as in most. Water can seep under the chipset and will take longer to dry. The connectors can also retain water and take longer to dry. Place on side to help in draining.
Low pressure compressed dry oil free air can be used as well, but carefully. A shop vac blower... carefully. This can also created an Electro Static Discharge hazard though. Don't touch the phone and nozzle or vac at the same time. Dry air raises the risk of ESD damage. Earth ground yourself before touching the phone; a ESD mat and wrist strap are preferred. Be aware of this hazard. Generally in circuit assemblies are relatively well protected. Points on the mobo can lack input protection and it's best not to touch them.
Heat drives out moisture ie hot boxes that are still used in humid climates to provide a dry environment for humidity sensitive equipment. Up to 120F is perfectly safe for drying. Don't expose the display to direct sunlight to speed drying though. Good luck.
Click to expand...
Click to collapse
Ok, I will keep those things in mind when following those instructions. Thank you again for your kind help.