Related
Hello good people,
I've been searching the forums but i don't seem to be able to find a solution for my dead kaiser.
I'll explain the problem:
When i push the power button on my Kaiser, it start's booting the first part, displaying the "smart mobility" slogan by HTC, after a few seconds, some data appears in red, in the right lower corner of the screen, this is what is says:
R 1.27.12.11
G 22.45.88.07H
D 1.56.00.00
After displaying this for a while (about 1 min.) it goes to the Windows Mobile Splash Screen.
After displaying this for a few seconds (5 to 10 secs) it makes the "empty battery" sound and shuts down.
Can someone help me ?
*** And NO, the battery is NOT empty ... i've charged it over night, and the power light was green. ***
I've tried booting with and without SIM and MicroSD cards ... makes no difference.
ttenhag said:
..snip*** And NO, the battery is NOT empty ... i've charged it over night, and the power light was green. ***
I've tried booting with and without SIM and MicroSD cards ... makes no difference.
Click to expand...
Click to collapse
Will it boot with the phone plugged in to power?
Bill
Yeah, try booting with the charger on. Chances are that your battery' life is out..
Reagdrs,
Carty..
I have had the same thing and wondered if it was the battery... except that sometimes it will stay on for about 2 minutes, sometimes half an hour... but most of the time as soon as it goes to the Today screen, I get the battery dead sound and then it turns off. I am going to try to use another battery to see if that makes a difference.
it's not the battery
I've tried with the power cord on the phone, it does 2 things:
1. The same thing as i said before
2. Doesn't boot at all, it halts on the screen where the red data shows up and stays there until you take the power cord off and the battery out.
It does one of these things, randomly.
I've also tried with another battery from my friends kaiser which works perfectly.
So i guess it's not the battery, anyone another idea what it could be?
Might be something wrong with the firmware or anything? problem is, i can't flash it if it doesn't boot can i ??
any ideas ?
Today i managed to get my hands on a brand new kaiser battery, my uncle has a brand new kaiser and i borrowed his battery.
His battery was full, i put it in my kaiser and tried booting, same problem as above.
I've tried with the power cord plugged into the phone, the charging led went on, and i tried booting, same as above.
Later i've tried with the USB cable connected to the phone and the computer, still the same.
I've also tried soft&hard resetting with the new battery, no succes.
So therefore, i believe it's not a battery or a power problem, it must be firmware corrupted or something of the hardware broke ?
Does anyone has any idea how i can try to re-flash this thing ? to find out if that might be the problem ?
It's not the battery. Could be a bad flash or something. Try to reflash it. Yes, it will reflash even though it won't "boot" as you say. Try to reflash and then report back. Remove the memory card for now.
Also, what Rom and SPL are you using?
Ur going to have to force it into the bootloader to flash it, no biggie. Just hold down the power and camera buttons, and hold the soft reset button with the stylus, untill you get the tri color boot screen. Then flash away! I would flash a stock rom until u can tell weather your problem is hardware related or not. If hardware related keep the stock rom and spl, and try to warrenty return it.
O.k., this just happened to my Brand New kaiser last night too, WTF! Was running fine when the low battery icon came up with half battery life n shut down, now it wont start up at home screen for more than 3 secs before it shuts down and says the battery is dead even while its plugged in! There's no way to reflash or hard reset since it doesn't stay on long enough to do so. Just ordered my replacement, but reading different forums, it seems many people have experienced this with Kaiser and most around the same time, again, WTF!!!
kaalgoosy said:
O.k., this just happened to my Brand New kaiser last night too, WTF! Was running fine when the low battery icon came up with half battery life n shut down, now it wont start up at home screen for more than 3 secs before it shuts down and says the battery is dead even while its plugged in! There's no way to reflash or hard reset since it doesn't stay on long enough to do so. Just ordered my replacement, but reading different forums, it seems many people have experienced this with Kaiser and most around the same time, again, WTF!!!
Click to expand...
Click to collapse
Does it power off while beeing in bootloader? You doesnt have to start the device up to get into bootloader you know. Try checking if it shuts down while beeing in bootloader, if its not just reflash. Another thing, what spl and rom are you guys having this problem using?
It's alive!!!
Finally got it to bootloader mode before it dies and reflashed and it seems to be running just fine now. Using spl ver.1 with schaps 4.30 wm 6 (although users running the stock rom had the same experience). Got the "smart chip not provisioned mm 2" message most likely from at&t killing my sim card from a reorder as they did when I Returned the Iphone which is a rediculous policy(policing); having to constantly contact at&t to update to a new sim. Still, it makes me wonder what caused this defunct in the first place, and if it'll happen again tomorrow or the next day. Reflashing and reinstalling cabs is a Real *****, especially for a pda where people use their device for business and gather a collection of missed calls and lost connections when the Os decides to randomly crash. As much as I dig htc's devices, it's kinda strange how HTC, with such a huge marketshare with pda's, is so quiet about updates or firmware fixes. Anyways, long live the only source for htc fixes, XDA!!
Mine is still completely in the state in which i got it.
Just the stock HTC Firmware, rom's and loaders
Okay, a little update.
How the hell can i flash this thing if it keeps on bugging me with the "Wrong vender ID" message when i try to flash it ?
I know, install HardSPL ... but how can i ? without a possibility to connect ActiveSync?, you'll have to start the device for that and run activesync, but i can't because it won't even boot.
Is there any other way of getting this device to allow me to flash without needing to boot it up fully.
I have no problems getting in to the Tri-Color bootloader, but no further.
When updating it gets to 1%, then my PC gives the message: "Wrong vender ID, please use your own device's update utility" and the phone stays at 1% till i rip out the battery.
ok guys I have the same problem with two of my kaiser's
I can power them up but in aproximately 1 minut goes off, no matter if the charger is plugged or not, it doesn't make a difference
I can put the phone in tri-color screen and stays there with no problem
and I can flash them with no problem because they are olipro already
but after flash them with anything still the same problem ???
so if anybody has a clue or maybe a rom to fix this would be great
thanks
best regards
linterna
One more thing. I have the same problem but mine when starts flashes Blue LED when was good hasn't. I Started few times and it works for 2-3 weeks and again. Best to do is to not use camera. Every time it happends i ise my camera and battery was middle-low. I think its some problem with camera. Many times it don't want to start up or saids that there is no memory for saving photo. Maybe i should flash rom from wersion without cameras.
im having the same problem, has anyone solved this?
Yeah solve . HTC as a kids toy .
Buy Nokia! Or SonyEricsson.
I won't buy smartphone ever again.
Does not boot to the OS
I have the similar problem...... My kaiser is dead not even booting with battery only (not plugged to the PC or external charger).
However when I plugged it to the power source it boots up and continue to the OS and boom (shuts off) in split of second.
I tried different flash and it propelry boots and got windows up and running when plugged to the PC with the old ATT test ROM which I got from the xda threads.
But with the latest roms it wont boot to the windows , it dies before that.
Anyone having idea what could resolve this.
any update on this? i am having the same problem. i tried a hard reset already with no success it goes to the splash screen and says "the device is clearing the storage. please wait" then pings and turns off
r 1.65.21.18
g 25.88.40.05h
d 3.57.00.00
my phone is completely stock and has never been unlocked or messed with. found an updated at&t rom, i ran it and none of the numbers change in the bootup, then goes to the splash screen and says again "the device is clearinng the storage. please wait" and then pings and turns off.
also i have been searching for the oilpro or jockeyw hard spl files on google and on here but have found nothing, the search function doesnt seem to be able to find much.
any help would be appreciative, thanks in advance
Don't mean to hijack but didn't want to make my own thread when this one was here. I'm not having exactly the same problem as everyone else but I am having a battery issue. It works fine and says it's charging when plugged in but when I unplug it the battery goes down fast (like 1-4 % a minute) and when it hits around 70%, it shuts off. Then whenever I turn it on, it immediately shuts down before the Today screen fully shows (like others are mentioning here). I have to plug it back into the charger to get it to turn on again.
Could this be a bad flash too..? I know I did one of the latest HardSPLs and tonight I just now updated to the latest stock AT&T ROM. But it can't be a flash because the night I got it (bought it used on eBay), I was playing with it not plugged in using Skype and it shut off on me. I didn't think much of it and had always had it plugged in since then.
I'm assuming I simply need a new battery.. I've emailed the original owner and she says she never had any problems with it like this.
Zerxer said:
Don't mean to hijack but didn't want to make my own thread when this one was here. I'm not having exactly the same problem as everyone else but I am having a battery issue. It works fine and says it's charging when plugged in but when I unplug it the battery goes down fast (like 1-4 % a minute) and when it hits around 70%, it shuts off. Then whenever I turn it on, it immediately shuts down before the Today screen fully shows (like others are mentioning here). I have to plug it back into the charger to get it to turn on again.
Could this be a bad flash too..? I know I did one of the latest HardSPLs and tonight I just now updated to the latest stock AT&T ROM. But it can't be a flash because the night I got it (bought it used on eBay), I was playing with it not plugged in using Skype and it shut off on me. I didn't think much of it and had always had it plugged in since then.
I'm assuming I simply need a new battery.. I've emailed the original owner and she says she never had any problems with it like this.
Click to expand...
Click to collapse
I've just started having the same problem as you. Very annoying. Mine phone is a year and a half old now, so i'm assuming the battery is coming to an end.
Charge battery, will last a while, but goes down to around 80-70% and then it says plug power in blah blah blah and dies. Then when you charge it, it stays on one or 2 bars for a bit and then jumps to 100% fully charged.
Saw a procedure to "reset" the battery. Supposedly have to take the battery out for a bit then plug in and charge fully over night with the phone OFF. None of this seemed to work for me... I'm due for an upgrade in January, so is it really worth paying for a new battery... hmmm
Nightmare.
Got my Diamond today, and charged it up.
It ran out 5 minutes ago, so I plugged it into the mains charger.
It vibrates, shows HTC and then gets stuck in a constant reboot. It's like it gets a little charge, uses it, then restarts the process.
I guess the battery is so dead that even the mains charger cant give it enough boost to start charging.
Help Please
If you only got it today then id be sending it back as it seems to be a faulty unit. Perhaps someone can give you a fix but if it was me, id be demanding a new working unit...you just never know what other faults the phone might have.
Good job I didn't Hard-SPL it straight away.
Damn, Always happens to me.
Are you trying to charge it with the wallcharger or by usb to a computer.
Beacuse if you are doing it by the computer there is an option on the phone that disables charging when conected to the computer.
Good luck dude.
Definately wall charger.
I think it's f(***d
I'll go back to my Kaiser and wait for the Raphael I think.
i would first try to charge the battery device turned off!
i noticed that the led in center button does not blink in the beginning but it should charge!
after a while try a hard reset!
Tried the following:
I cant switch off the device as soon as power is applied via USB it switches on. Tried holding the power button down but nothing.
Tried entering bootloader but same reset loop.
Tried hard reset, gets to grey screen with blue text but then reset loop again.
I tried leaving the battery out for half an hour and trying again but soon as usb is in it powers up and reset loop.
I put a multimeter on the battery and it is dishing out 3.7v as expected.
I think the device is knacked, even though I was using it for most of the day.
laporte said:
i would first try to charge the battery device turned off!
i noticed that the led in center button does not blink in the beginning but it should charge!
after a while try a hard reset!
Click to expand...
Click to collapse
Usually a hard reset solves everything (hopefully)
Sergio PC said:
Usually a hard reset solves everything (hopefully)
Click to expand...
Click to collapse
Tried hard reset, gets to grey screen with blue text but then reset loop again.
Nope
leave it charging for at least 10 minutes before turning it on.
bakman said:
leave it charging for at least 10 minutes before turning it on.
Click to expand...
Click to collapse
I cant switch off the device as soon as power is applied via USB it switches on. Tried holding the power button down but nothing.
don't even touch the power button!
the device should not start if you touch nothing and just plug the powercable!?
i don not think that you press the powerbutton accidentally while plugging the cable, i hope i'm right?
Without touching the power button, I plug in the charger and the phone vibrates and starts.
From dead:
1. Plug in charger
2. I get 2 swirls of white on the round button thing
3. Phone vibrates
4. Smart mobility logo shows
5. Phone reboots
GOTO 1:
i miss the touch diamond screening with rom version etc.
normally it shows up before the htc smart mobility screen.
i don't think the battery is the badguy. seems more a fault in ipl or spl?
You're right.
I was wrong when I said smart mobility.
It comes up with TOUCHDiamond across the centre of the screen and right where the little red numbers USUALLY appear in the bottom right, it reboots before that.
To perform a hard reset
1. Pull out the stylus.
2. With the device turned on, press and hold the VOLUME DOWN and ENTER buttons, then press the RESET button with the stylus tip.
3. Release the RESET button, but continue pressing the VOLUME DOWN and ENTER buttons until you see message on the screen
4. Release the VOLUME DOWN and ENTER buttons, then press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset
save this info on your computer
Sorted!
I left the battery out overnight, and when I came to work this morning, I plugged it into the charger and it didn't automatically start up so it got a good 3/4 hour charge which then enabled me to fire it up for a full charge.
congrats! i hope for you that this problem doesn't come back!
Sounds to me like it also could have been the power button was jammed pushed in. Maybe leaving it for a while without pushing the button did the trick, allowing it to release itself.
In case that was the problem, keep an eye on the power button in case it seems to be a bit dodgy. If it is going to do it again, then you want to swap it immediately for a replacement brand new unit. After a while, if you try to swap it out, they will give you a refurbished unit, not a brand new one!
Of course it could have just been a software bug, that was cleared by letting it fully power down (as others have said).
Just make your decision quick before you end up with a refurbished model for replacement.
Just to let you all know.
Over the weekend I fully charged my Diamond, and without even making a phone call or using WiFi, Bluetooth or anything the battery lasted 1.5 hours.
It's gone back to clove now for a replacement.
I've seen a few people having this issue so I advise getting it back for replacement asap.
My diamond got very hot during normal use (without charger). Is that normal? Not the battery but the actual device.
Yesterday, I was flashing back to the JH6 again. It stuck at factory.rfs for a long time. Then, I tried to restart. After phone is off, it couldn't turn on any more. No matter, press vol down + power or press vol up and down then plug in usb with ODIN on. Or just press power button. I've tried the whole day even try to put on wall charger overnight. There is no battery screen during charge just for the reference.
It seems there is no way to bring it back other than jtag? anyone has any experience about this dead phone and bring it back to life?
Thanks.
Have you tried another battery? Just to make sure it didn't take a dump. It has been reported by very few that has happened.
Same thing happened to me it froze during the Factory.rfs so I turned it off and the phone wouldn't turn back on. I panicked and found somewhere else on these forums although I cannot find the thread again. What I did I just plugged my phone into the wall charger for a couple minutes with the battery. Then I unplugged it and took the battery out for a another minute then put the battery in and try to turn it on while holding the volume - or + I forgot, and if you start to see Orange Text being dumped to your screen chances are you can force it back into Download Mode. Just keep trying different button combos to get it working, unless I was extremely lucky but I do not think these phones can be bricked so easily.
Thanks. I did see the thread you mentioned and tried every way I can but not available. Fortunately, I got ATT warranty center to send me a replacement. However, the only catch is that I'm not sure if it's unlockable now since it might come with JH7. If that's the case, I'm gonna sell it and get other phone.
samsung captivate brick
i have the same problem... im running windows 7 x64(64 bit) and i was updating my phone to the rooted 2.2 froyo update via odin with the "I897UCJI6-OCD-REV02-Low-designgears" while updating the phone when the odin program froze and ruined/bricked my phone... i have tried all the steps to try and un-brick my phone but at this point im about ready to give up.... at this point my phone will not power on in any mode nor will it go into recovery mode or download mode... if any one has any info on how to fix this please let me know....
After an unfortunate rooting session with my Motorola Milestone, the phone now returns into an "dead" mode. It refuses to start at all. I tried charging it and see if it starts by itself, but it doesn't budge and the little while led doesn't lit. The only time when it lit is when I connect it to the PC. I tried putting in it a new battery, taking out the SD card and SIM, but to no avail. I remember seeing a video where a guy used a dissected USB cable to spark the phone into turning on again, so I take it I'll have to use a "hardware approach"? Please help.
I tried following this guide, though without success. The phone still has that white LED lit when it's connected to the PC.
After a reply on this thread I also made, it might be possible that the battery is charged, but the phone refuses to boot at all. Is there any way to unbrick the phone in this state?
Do you think your device is really BRICKED?
If so, you can try to flash your original sbf file into your phone. Guide here: http://forum.xda-developers.com/showthread.php?t=696845
If you are using a Linux, google for "sbf_flash".
I agree with my front floor..ermm, u dont need to worry about its 'dead'. just flash original sbf can rescure your phone.
I had the same problem too, but good news is I tried to revive my phone successfully recently, btw your phone is not 'dead', it's just staying in limbo state, the solution is to pull out the battery and don't connect to any usb, don't try to power it up, it must be completely out of power wait about 12 hours, and then try to power your phone, I think there is some capacitors in the phone which retain the phone state, to make it out of power will wipe out it's state, good luck
algopem said:
I had the same problem too, but good news is I tried to revive my phone successfully recently, btw your phone is not 'dead', it's just staying in limbo state, the solution is to pull out the battery and don't connect to any usb, don't try to power it up, it must be completely out of power wait about 12 hours, and then try to power your phone, I think there is some capacitors in the phone which retain the phone state, to make it out of power will wipe out it's state, good luck
Click to expand...
Click to collapse
"My phone is in limbo state... "
That's a pretty cool statement.
From technical view, it might have happened that something caused a kind of deadloop when reading scratchpad SRAM inside OMAP processor.
This SRAM, as well as the internal RTC is powered by a small battery soldered on the mainboard, while the phone is shut down and the battery is taken out.
What you did was, to wait untill this battery became uncharged.
All SRAM and RTC setting as well then gets erased.
Afterwards the CPU will start up with empty scratch SRAM, might be called a "real" cold boot
Normally the phone should not behave like this. Even if SRAM is not valid the phone should boot up...
...but anyway as you observed it like this, it might happen.
@andoruB:
Apart from that, the Milestone is hard to brick in general.
Might happen though, if you do evil things while flashing new firmware.
Especially while flashing bootloaders...
If you got some more information about the things you did, would be helpful!
Good luck anyway!
scholbert
andoruB said:
After an unfortunate rooting session with my Motorola Milestone, the phone now returns into an "dead" mode. It refuses to start at all. I tried charging it and see if it starts by itself, but it doesn't budge and the little while led doesn't lit. The only time when it lit is when I connect it to the PC. I tried putting in it a new battery, taking out the SD card and SIM, but to no avail. I remember seeing a video where a guy used a dissected USB cable to spark the phone into turning on again, so I take it I'll have to use a "hardware approach"? Please help.
Click to expand...
Click to collapse
how did u root it? can u give a more detailed description? and hows ur phone? sometimes, the milestone would just shut off and wont come up if the battery is gone. Try charging it for maybe 2-3 hours, untouched, and see what happens.
Have this exact problem. Was doing a nandroid recover when the phone got stuck. Pulled the battery out. Placed it back in, pressed the power button. Nothing.
Led lights up only when connected to the computer's USB. Battery was charged before Nandroid recover. Used nandroid a lot of times but for some reason, my stone stopped playing nice.
I just removed the battery. Hoping this works. Can someone please post if you got this same issue resolved? I like this phone no matter how slow it goes sometimes. Thanks!
I completely forgot about this thread, sorry guys!
I don't remember exactly what happened, it's been so long... but I do remember I left the phone "inactive" (it's not like i had much of a choice! XD ) for 1 or 2 months, with the battery out. After I got hold of a wall charger, I plugged in the battery, after I plugged in the charger, and what do you know? It worked! It started charging (was 60% charged, fully charged, I unplugged it, but after putting it to charge again just to make sure it was fully loaded before I would flash a new ROM, it was charged up to about 80%, weirdly, so I guess it was a weird battery problem)
I do remember I didn't do anything to it, so I'm not sure what to tell you guys to do, except leave out the battery for a month or so ^^;
Hello all,
I searched around, but didn't find anything quite like my issue so figured I'd create a new thread.
I work for a company that uses Galaxy Tabs for various purposes. One of our men brought back their VZW Galaxy Tab (SCH-i800) and it was in an infinite boot loop.
I went to recovery and attempted to do a full wipe. This did not work (partitions were all jacked up) so I couldn't get it fixed. I'm not sure if the guy tried to root the thing and broke it or what.
Anyway, I was attempting to root then fix the partitions (then was going to flash a stock unrooted rom) and ended up soft bricking it (Phone Icon -- /!\ -- Computer Icon). The issue I'm having is the only time that screen comes up is when the device is plugged into the wall. It turns on, then off, then on, then off. If I unplug the device, it shuts down with no way of bringing it back up. I've tried holding power for 5 minutes, the same amount of time with power + vol up and power + vol down. Plugging it into the computer's USB ports does not help either.
It's like the battery is drained but it won't charge when it's on the soft brick screen. I've had it plugged in to the wall for almost 6 hours now with no hope in sight. When it's plugged in, I feel heat on the back of the device like it would normally be charging. The AC adapter is also the standard warmth after a lengthy charge.
I was wondering if anybody has had similar issues with this device and if there is any way to correct it.
--- EDIT 8/10/2012 ---
Another thing of note is when the device is charging, I can power it down by holding power for a few seconds, but the Soft Brick screen pops back up almost immediately upon release of the button.
I cannot boot into recovery or the standard download mode even when it's plugged in.
As long as you can get the Phone ! PC screen, your'e good, because this screen IS as a download screen. Go to this screen and flash a known good ROM.
ableeker said:
As long as you can get the Phone ! PC screen, your'e good, because this screen IS as a download screen. Go to this screen and flash a known good ROM.
Click to expand...
Click to collapse
You must not have read the whole thing. Not a problem.
The only time I get the Phone ! PC screen is when it's plugged in to the wall. As soon as I unplug it, it goes away and the device won't start up no matter what I try.
When you connect the tab to the pc, is it recognized by Odin.
Sent from my GT-P1000
salahmed said:
When you connect the tab to the pc, is it recognized by Odin.
Sent from my GT-P1000
Click to expand...
Click to collapse
No... When the device is unplugged from the wall it is shut down and won't boot back to the download screen, recovery, nothing. It doesn't turn on. There are occasions where the download screen stays up but it appears to just be frozen. The computer doesn't recognize it and neither does Odin.
I left it plugged in when I left work on Friday... Going to see if charging for the weekend does anything.
MaskedDriver said:
No... When the device is unplugged from the wall it is shut down and won't boot back to the download screen, recovery, nothing. It doesn't turn on. There are occasions where the download screen stays up but it appears to just be frozen. The computer doesn't recognize it and neither does Odin.
I left it plugged in when I left work on Friday... Going to see if charging for the weekend does anything.
Click to expand...
Click to collapse
No dice.. still jacked.
I determined the following scenarios may have happened:
1) The battery died (bad battery) during a software update and messed up the partitions
2) The battery died (bad battery) while he attempted to (unauthorized) root or flash the device, messing up the partitions.
The only thing I'm sure of is the battery is fried so any kind of hacking I can do to the device are for naught. I was able to get it to connect to Odin this morning for about 3 minutes (after having it plugged in to the wall all weekend). During the flash it shut down again bricking it even worse. Now the device won't turn on when plugged in to the wall.
Thanks for the suggestions and help. I'm calling this a lost cause at this point. We're just swapping out the device for a new one. Once that's complete, I may tear the device down and try to do a reset on the main board to see if that does anything, though I doubt that's the case.
Right I had exactly the same problem as you (exactly the same symptoms) but I have now fixed my tablet.
Like you I got to the point where the Tablet had enough charge to actually unplug it and connect it to my PC where I then tried to flash a stock ROM using Odin. About three quarters of the way through flashing the stock ROM the tablet died, disconnected from Odin and I got a message in the task list in Odin advising me that the process had failed. Even weirder my PC did an emergency shut down and restarted in safe mode.
Anyway I tried it again but when I started my machine, once I'd logged onto my desktop I started up Odin as quickly as possibly, selected the .tar file and pressed start as quickly as possible....it worked and my tablet was flashed with a stock ROM. However my battery was still pretty much dead and the first time of charging once it had been flashed with the ROM took about 24hrs plugged in at a mains charger for the battery to reach 100%.
My point is persevere with it and you will fix it. I was at the point where I was about to send it off to be un-bricked but obviously I'm glad I didn't now.
It is a ***** of a brick though, this 'coma brick'.
I've been having these same issue with my friends i800 galaxy tab. Can you chime in and offer some advice?
Sent from my Galaxy Nexus using Tapatalk 2
same problem-solved
I was having the exact same issue. the device screen was completely black when plugged into the computer. I was just about to give up when, all of a sudden the device went to the boot error screen while plugged into my computer. Apparently, it must remain plugged into the computer for about 20-30 minutes. Once this screen appeared, I ran the Heimdall one-click unbrick utility, and like magic, my galaxy tab was working again. Give it a try, and good luck.
MaskedDriver said:
Hello all,
I searched around, but didn't find anything quite like my issue so figured I'd create a new thread.
I work for a company that uses Galaxy Tabs for various purposes. One of our men brought back their VZW Galaxy Tab (SCH-i800) and it was in an infinite boot loop.
I went to recovery and attempted to do a full wipe. This did not work (partitions were all jacked up) so I couldn't get it fixed. I'm not sure if the guy tried to root the thing and broke it or what.
Anyway, I was attempting to root then fix the partitions (then was going to flash a stock unrooted rom) and ended up soft bricking it (Phone Icon -- /!\ -- Computer Icon). The issue I'm having is the only time that screen comes up is when the device is plugged into the wall. It turns on, then off, then on, then off. If I unplug the device, it shuts down with no way of bringing it back up. I've tried holding power for 5 minutes, the same amount of time with power + vol up and power + vol down. Plugging it into the computer's USB ports does not help either.
It's like the battery is drained but it won't charge when it's on the soft brick screen. I've had it plugged in to the wall for almost 6 hours now with no hope in sight. When it's plugged in, I feel heat on the back of the device like it would normally be charging. The AC adapter is also the standard warmth after a lengthy charge.
I was wondering if anybody has had similar issues with this device and if there is any way to correct it.
--- EDIT 8/10/2012 ---
Another thing of note is when the device is charging, I can power it down by holding power for a few seconds, but the Soft Brick screen pops back up almost immediately upon release of the button.
I cannot boot into recovery or the standard download mode even when it's plugged in.
Click to expand...
Click to collapse
I am having this issue with my sch-i800.... phone /!\ pc screen only when plugged into the wall, and no recognition of it on the pc. Any way of fixing it?