Database Develop

[Q] [SOLVED!] USE ODIN >1.7 (semi?) bricked ... despite precautions galaxy s odin

Hey guys,
First of all I checked every brick thread I could find and I am pretty sure none of the solutions applies to my problem.
I've flashed hundreds of times on numerous phones so I take most precautions to make sure I don't brick my phone, still, that's what happened now for the first time.
Situation:
- Download mode and recovery mode checked... both working
- Had Darky's DarkSteel 3.0 running with LagFix (no problems)
- Disabled LagFix by adding the folder
- Reboot ... disabled lagfix ... still running strong
- Flashed Darky's LegendarySteel 4.0 ... running
- Reboot ... hey no Voodoo ... oops lagfix folder was still there of course
- removed folder
- reboot ... still no lagfix ... OK so I accidentally chose the wrong Darky's ... The one with SpeedFix kernel not the one with Voodoo
- remember: lagfix folder still there, but I thought it would not be enabled as Darky's SpeedFix version had no Voodoo, also, Quadrant showed 900 like you would expect without lagfix
- Checked recovery/download just for precaution ... both working still
- Flashed the rom I wanted: Darky's LegendarySteel 4.0 with VOODOO
- So basically, I flashed WITHOUT "disable lagfix" folder, somehow thinking this would not be a problem considering LagFix wasn't running on the previous rom, and was disabled before flashing the previous rom.
- Clockwork Recovery clear cache / wipe partition ... choose zip ... run update ... OK REBOOT
- Stuck at Galaxy S logo
- No recovery
- Download mode works
- Tried Odin to flash stock rom using PIT 512 with and without repartition ... both just wait for a long time on some message "checking file system" and I don't know how long that should take but after 20mins I gave up.
- Tried rebooting and waiting forever as advised on the Voodoo site ("if you had a lagfix enabled previously, it will take forever, just be patient") well I waited forever (hours?) and still "Galaxy S" bootup screen
- Kies recognizes nothing
- Same for ADB
- Only download mode works ... Odin does recognize the device so all could not be lost right?
My questions:
- What should I flash (including firmware, PIT, odin version, repartition, wait time etc) to get up and running again?
Any help would be greatly appreciated!!!

nin2thevoid said:
Hey guys,
First of all I checked every brick thread I could find and I am pretty sure none of the solutions applies to my problem.
I've flashed hundreds of times on numerous phones so I take most precautions to make sure I don't brick my phone, still, that's what happened now for the first time.
Situation:
- Download mode and recovery mode checked... both working
- Had Darky's DarkSteel 3.0 running with LagFix (no problems)
- Disabled LagFix by adding the folder
- Reboot ... disabled lagfix ... still running strong
- Flashed Darky's LegendarySteel 4.0 ... running
- Reboot ... hey no Voodoo ... oops lagfix folder was still there of course
- removed folder
- reboot ... still no lagfix ... OK so I accidentally chose the wrong Darky's ... The one with SpeedFix kernel not the one with Voodoo
- remember: lagfix folder still there, but I thought it would not be enabled as Darky's SpeedFix version had no Voodoo, also, Quadrant showed 900 like you would expect without lagfix
- Checked recovery/download just for precaution ... both working still
- Flashed the rom I wanted: Darky's LegendarySteel 4.0 with VOODOO
- So basically, I flashed WITHOUT "disable lagfix" folder, somehow thinking this would not be a problem considering LagFix wasn't running on the previous rom, and was disabled before flashing the previous rom.
- Clockwork Recovery clear cache / wipe partition ... choose zip ... run update ... OK REBOOT
- Stuck at Galaxy S logo
- No recovery
- Download mode works
- Tried Odin to flash stock rom using PIT 512 with and without repartition ... both just wait for a long time on some message "checking file system" and I don't know how long that should take but after 20mins I gave up.
- Tried rebooting and waiting forever as advised on the Voodoo site ("if you had a lagfix enabled previously, it will take forever, just be patient") well I waited forever (hours?) and still "Galaxy S" bootup screen
- Kies recognizes nothing
- Same for ADB
- Only download mode works ... Odin does recognize the device so all could not be lost right?
My questions:
- What should I flash (including firmware, PIT, odin version, repartition, wait time etc) to get up and running again?
Any help would be greatly appreciated!!!
Click to expand...
Click to collapse
Flash some ecleir ROM with 512 re-partition. Hope this helps.

ragin said:
Flash some ecleir ROM with 512 re-partition. Hope this helps.
Click to expand...
Click to collapse
Try the Odin 1.7 from my thread posted here.

Try flashing back to the kernal that you had on the rom first?
Don't really know if it would help.. just taking a shot in the dark..

God I love this forum. Thanks for the tips all. I was using older ODIN and now using 1.7 (couldn't find it in the specified thread since the link was missing ^^ but used the forum search instead).
It's flashing ... At least that!! I will report back how it goes!
Edit:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> zImage
<ID:0/003> dbdata.rfs
<ID:0/003> factoryfs.rfs
<ID:0/003> param.lfs
<ID:0/003> modem.bin
<ID:0/003> cache.rfs
<ID:0/003> Removed!!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Live and kicking again! Woot... Thanks all!

Well, atleast we know that odin 1.7 is more stable and more "unbrick" friendly =)

nin2thevoid said:
God I love this forum. Thanks for the tips all. I was using older ODIN and now using 1.7 (couldn't find it in the specified thread since the link was missing ^^ but used the forum search instead).
It's flashing ... At least that!! I will report back how it goes!
Edit:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> zImage
<ID:0/003> dbdata.rfs
<ID:0/003> factoryfs.rfs
<ID:0/003> param.lfs
<ID:0/003> modem.bin
<ID:0/003> cache.rfs
<ID:0/003> Removed!!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Live and kicking again! Woot... Thanks all!
Click to expand...
Click to collapse
If it has helped you, please post a reply in my thread. can help others like you.

from my experience odin works the best if you connect your phone and hit the flash button immediately. connecting the phone in download mode and waiting with it always caused the flash process to "stuck" just like you describe.
anyway happy 1.7 helped you.

I had the exact same problem last night.
to solve the issue... I basically reflashed to ECLAIR JM8.
Then installed the ROM i wanted from clockwork recovery, and everything went back to normal!
Hope things work out well for you! cheers!!

I guess Re-Partition solved the problem. This should also work with Odin 1.0 / 1.3

No it was 1.7 that solved it since I did the exact same steps as with 1.3. Upgrading Odin was the fix for sure. I'm surprised not many people use 1.7... all the tutorials and guides point to 1.0 and 1.3.
Thanks for all the help guys!

hi gays,
actuly i have the same problem " screen of death "
but it happened whit my when i tried to flash -speedmod kernel - and - ce-root- in PDA
and it's stopped in middel of the action -- it happened in odin3 1.7 > it's naver happened in odin3 1.3 and odin3 1.3.2
i think there something wrong with 1.7
--sorry for bad English - i hope you understand what i'm tring to say
thanks for your time !!

I have a similar problem, which is not solved yet. I would be glad if someone would help.
Explanation of my probs:
I think I've bricked my SGS. It's a European version, not branded with T-mobile or any operator.
Friday I flashed the JPU (Android 2.2.1) and it worked fine. I've updated it several times via Odin, and never really had problems.
Then I installed the Voodoo recovery image and a custom ROM (Darkys 5.2 ROM). Still worked fine, a quadrant score of 1650. But then... I went to the recovery and chose to partition the internal SD card (EXT3/4). The phone said it succeeded doing this, but then it rebooted and I only got the Samsung logo (in white, no colors). Waited for 10 minutes, nothing happened.
Now I can't get it into recovery mode, however, the 3-button combo is still working, so I can get it into download mode as usual. But it does'nt work. It starts, I get the green slider on the phone, but after a very short time the update stops, it happends while Odin writes sbl.bin
I've tried several ROM's, but it does not work. I don't know what to do now - why can't I flash the phone even though it's in download mode?
Hope that someone can help me.
--- update ---
Hmm, maybe I'm on the right track now - I hope so.
Now I can turn on the phone, but it does go into the stock recovery, even though I just turn it on. It's the stock recovery (Android system recovery <2e> Samsung recovery Utils - for BML -
I downloaded Odin 1.7 from this link:
Download Odin-1.7with.pit.512.803.zip from General-Search.com
I did this on my work computer instead of my laptop. Never used Odin on this computer before. Then I just wanted to test Odin, so I chose some random PDA file I had on the computer. I chose the JPK Root + Busybox 1.17.1 + 2e\i9000_Kernel.tar that I used for rooting the JPK firmware when I was running that.
Then I have flashed the other file from that package (I9000XXJPK_Kernel.tar) - but when I turn on the phone, it stops but shows the white Galaxy S logo.
...more to come.
UPDATE!
UPDATE! Flashed JM7 firmware (that's the newest I already had downloaded on my work computer) and the beast is ALIVE AGAIN! Hallelujah!

I solved it with old ODIN flash 1.3 firmware JPA_JP4_U_JPP.tar (no pit file) USB pluged and unpluged a cuple of times. no repartition and no bootblock . After first flash i had to wipe and factery restore in 2e recovery. and flash again. After that the phone was fine. The KIES version i have installed is 1.5.3.10103.102. I think it is the driver version that KIES installs that is the problem, You could try installing older KIES vith older drivers. After first flash the new firmware could not install aps after first boot, thats why i wiped and flashed again.
Sory for bad English

Help pls.. I can run but it failed in the end after waiting it to run. I had tried reopening the oldin and replug in batt all no use...

Thank you so much for the tips here guys, been trying to recover my nephews softbricked i9000 for 5 days now - finally sorted, woohoo!!!!
I used Odin 1.7, Re-Partitioned with the 512 pit file and flashed a stock rom.
This was my last attempt too so Christmas has come early!

Black Screen after Samsung Boot

I was running Webstar's "Ultimate" ROM 3.0, after which I decided to go to stock and then upgrade to a different ROM.
I flashed stock 2.2 stock firmware with Odin 1.7 with 803 pit (from samfirmware.com). Now my phone is stuck on a black screen and vibrates after the Samsung boot animation.
I had disabled the lagfixes and tweaks from recovery but the files still stayed back on the sdcard.
This is what Odin says :
<ID:0/023> Added!!
<ID:0/023> Odin v.3 engine (ID:23)..
<ID:0/023> File analysis..
<ID:0/023> SetupConnection..
<ID:0/023> Initialzation..
<ID:0/023> Get PIT for mapping..
<ID:0/023> Firmware update start..
<ID:0/023> cache.rfs
<ID:0/023> factoryfs.rfs
<ID:0/023> modem.bin
<ID:0/023> param.lfs
<ID:0/023> zImage
<ID:0/023> Removed!!
<ID:0/023> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Recovery mode/Download mode works for me. I tried clearing cache/factory reset, it worked, but my phone's still stuck on black screen.
I tried reading through similar threads on the forum, but most of that hasn't helped me. I also get the yellow screen something like -----|---- (which I haven't tried with Kies)
I'm downloading the 2.1 stock firmware now, I will try flashing it with Odin.
I just got this phone last week so I deserve to panic a little :\

Same issue with my friend phone
she said was playing with apps in the markets then crash
then Black screen after the Big S show.
Tried wiping cache and data, not working
Flash it with stock 2.1, not working ~
stucking and need assistance
video of booting

I tried 2.1 firmware without PDA and Re Partition on Odin, still doesn't work.. It says successful but stuck at black screen post reboot.
Edit: *Finally works*
I did an odin flash with 512 pit, with repartition selected. After boot format sd/factory reset and clear cache. REMOVE USB, and reboot.
Hope this works for her.

killslayer said:
I tried 2.1 firmware without PDA and Re Partition on Odin, still doesn't work.. It says successful but stuck at black screen post reboot.
Edit: *Finally works*
I did an odin flash with 512 pit, with repartition selected. After boot format sd/factory reset and clear cache. REMOVE USB, and reboot.
Hope this works for her.
Click to expand...
Click to collapse
mind finding the exact link for the Odin and Pit and Firmware for me ?
i wanna try to exactly the same thing, hopefully will work for her too

wildbat000 said:
mind finding the exact link for the Odin and Pit and Firmware for me ?
i wanna try to exactly the same thing, hopefully will work for her too
Click to expand...
Click to collapse
Sorry I dont have the links anymore, you'll have to look around a bit. I got the firmware from samfirmware.com
You can get the firmware for your area there and search for odin 1.7 with pit files, shouldn't be hard.

Still stucked
anyone know a fix
got Download mode and Recovery Mode
but just won't boot up .... (as shown in the video)
anyone have a clue?

Flash an old Eclair firmware that uses 512.pit. (In fact, all of them should.) Get them off www.samfirmware.com

did it many times~ not working

[HELP] 3-button combo deleted?

Hi
I was trying to flash another ROM on my SGS, while having some bugs on CM7.
I formatted system, cahce and data, and did wipe data/factory reset + wipe cache.
I kept getting an error on flashing the new ROM, and accidently hit the "reboot system" while navigating around in CWM3.0.0.5. Now I can't get back to CWM with 3-button combo and got no ROM on my phone?
what to do? Wierd enough I can get into download mode
thanks in advance
PS: I normally use 3 button combo to get into CWM, and did this prior this episode

just flash via odin, with 3 files and re-partition.
that should work.

derrzredeem said:
just flash via odin, with 3 files and re-partition.
that should work.
Click to expand...
Click to collapse
I'm not so farmiliar with Odin yet... tried it a couple of times, sticking strictly to a guide, that I cant find right now :S
Could you give me a quick tutorial in what to combinate .e.g.?
PIT? PDA? PHONE or CSC? And what is what?
I know I used to flash a radio with the PDA function...
thanks

you should flash a low level package means a 3 files PDA, MODEM and CSC.
i.e XXJPU which contains XXJPU_modem, OXAJPU_CSC, and XXJPU_Rev3_PDA. Now you should put the files according to the names (like PDA in PDA, Modem in Modem and so on). I usually use 512pit for re-partition.
You should not put modem in pda when flashing using odin, like i said before "put the files according to the names"
ps. Do not tick any other option except repartition, (F. Reset Time, and Auto-reboot) when going back to samsung ROM from CM7
Good Luck

derrzredeem said:
you should flash a low level package means a 3 files PDA, MODEM and CSC.
i.e XXJPU which contains XXJPU_modem, OXAJPU_CSC, and XXJPU_Rev3_PDA. Now you should put the files according to the names (like PDA in PDA, Modem in Modem and so on). I usually use 512pit for re-partition.
You should not put modem in pda when flashing using odin, like i said before "put the files according to the names"
ps. Do not tick any other option except repartition, (F. Reset Time, and Auto-reboot) when going back to samsung ROM from CM7
Good Luck
Click to expand...
Click to collapse
Thanks a lot. You just managed to answer my next question at the same time as I was about to put it out (regarding check marks F. Reset Time, and Auto-reboot)... looks like it is going through now... The blue line is increasing anyway under the litthe android builder
thank you so very much
EDIT: God dang it Phone bootet up once again in original rooted firmware anf 3e recovery is back

Hmm... seems I was a bit to fast on the keyboard anyway
Followed "How to: flash firmware and kernels" from post #2 in this thread
http://forum.xda-developers.com/showthread.php?t=723596
I found a 512 pit from the link, where I also downloaded Odin. I chose the I9000XWJS3.7z from original firmware package (from the link), which included a .tar file, that I chose as PDA.
The phone boots up now, but when as it is about to show android UI, it starts to vibrate and the screen turns black, and menu button + back button light up continously.
I can get into 3e recovery know though, but is there a way to flash clockworkmod or another custom recovery via odin og 3e recovery? or could I try another combination of pit and PDA file ind Odin?
thanks again
Odin log:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> modem.bin
<ID:0/004> param.lfs
<ID:0/004> zImage
<ID:0/004> cache.rfs
<ID:0/004> factoryfs.rfs
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!

You're in a bootloop. Try wipe cache partition and do a factory reset from recovery and then reboot.
If that doesn't work try a different firmware. A LOW LEVEL PACKAGE one, JPU for example.
Afaik, JS3 only had one file (and the new JS3 is using 803pit file, tho it comes with 3 files; for me 512 always gave the best result).
Edit : You need to use a correct pit file when flashing a firmware.
~drz

derrzredeem said:
You're in a bootloop. Try wipe cache partition and do a factory reset from recovery and then reboot.
If that doesn't work try a different firmware. A LOW LEVEL PACKAGE one, JPU for example.
Afaik, JS3 only had one file (and the new JS3 is using 803pit file, tho it comes with 3 files; for me 512 always gave the best result).
~drz
Click to expand...
Click to collapse
Just to make sure I got the last part right. 803pit is for JS3? but I can use 512pit instead?
where do I get 803pit? do you have a link?
Im downloading JPY and will test it, if 803pit og wipe doesn't work.
thanks for the response

larsn84 said:
Just to make sure I got the last part right. 803pit is for JS3? but I can use 512pit instead?
where do I get 803pit? do you have a link?
Im downloading JPY and will test it, if 803pit og wipe doesn't work.
thanks for the response
Click to expand...
Click to collapse
God, you need to learn to listen/read. Use JPU, JPY is a single file.
Ps. Good luck though
~drz

Okay, I thought the name JPU/JPY determined which area it is fore?
Im downloading from here
https://www.wuala.com/Samsung Galaxy S/Firewares , Updates and Odin/?key=AfzUZSU4SpKU
but I cant seem to find JPU...
thanks for your help. Im a bit noobish regarding samsung... Its buy far not the same as HTC hehe
EDIT: Can't I just flash an original firmware with Odin, and it such case? Where do I find it. tried JPY, JS3 from above link, and get bootloops no matter what. Those files are downloaded from the sticky guide in general section, and I followed the guide. If I need to use JPU, where do I download it? all 3 files?
Right now, the phone just vibrates in intervals, but contiounsly, with back button and menu button light on

Yes, every firmware is for different region. But you need to get your phone to work first, right?
After that you can flash any firmware you want
You can download JPU from http://samfirmware.com or find a thread by BogdanSNB in general section.
Btw, Gingerbread is out
~drz

SOLVED
Finally got it to work with XJWM9 as PDA, XEEJM1 as CSC, XXJM4 as PHONE and 512pit file.

Can't flash with Odin - Please help!

I have been trying to flash my Samsung Galaxy S i9000 for a week now with no success.
First off, it has a lot of problems connecting when I am in download mode. It has no problem at all when the phone is fully booted up, but Odin has a really hard time seeing it while the phone is in download mode. I have to restart the phone several times into download mode and pull the cable, etc until I can finally get Odin to see it.
Once I get Odin to finally see the phone in download mode I loaded the PIT and the PDA files from the tutorial for DarkyROM_10.2_Resurrection.
But when I hit start is just stops here:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
And will not go any further.
I originally rooted with one click, but I am afraid I might have messed that up. After I did the one click I was messing around with the phone and formatted the internal memory from the download screen. I even went back into one click to try to unroot, but it gives me an error message.
Did I mess up my phone? Is there any way to fix this?

have you ever succeeded in flashing with odin or first time?
have you closed all kies programs from task manager? (do you even have it installed?)
if you have win7, have you opened odin with right click menu->as administrator?
what ver. of odin do you use?
maybe the cable is faulty?
did you connect it directly to the comp or by some hub? (better connect directly)

guy7685,
No, I have never flashed before. This is the first time.
I tried running Odin as system admin, made no difference.
I do not have Kies installed.
I'm pretty sure the cable is good, it works fine for everything else including data transfer on my other phone, just not in download mode for this phone.
I've tried a few different versions. v1.30, v1.83, v1.85
When I tried in in v1.83 & v1.85 I get a fail, then this message:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
Any thoughts?

If you have another computer you can try it on, do that otherwise I think you need to install the drivers again. You can search for them or you can install them via kies. Once you have kies installed go to tools and install drivers.
Remember that before you open Odin you go through task manager to close all kies processes.
Good luck
Sent from my GT-I9000 using XDA

Got it to work
I was finally able to get it to work. I think I was using the wrong recovery screen or at least what I thought was a recovery screen because I finally got the guy in the construction picture and it flashed no problem with Odin.

After Odin Succes
Everything is ok and all thred completed (succesd 1 / failed 0)
After this, my galaxy tries to reboot but it only shows the flashing battery and will not reboot itself.
Help!

jimnycricket65 said:
Everything is ok and all thred completed (succesd 1 / failed 0)
After this, my galaxy tries to reboot but it only shows the flashing battery and will not reboot itself.
Help!
Click to expand...
Click to collapse
i have similar problem. Please have you gotten solution to this problem? Your help is appreciated. Thanks.

are you instaled drivers completly???

alireza17mah said:
are you instaled drivers completly???
Click to expand...
Click to collapse
Right Click -> Run As Administrator it should resolve the issue

If its showing the battery only then its probably the wrong flash file.
Sent from my GT-I9000 using xda app-developers app

SGH-i537 Wifi not working, can't flash odin

A few days ago I tried upgrading to 4.4.2 via safestrap and ran into some problems. Long story short I was stuck in Download mode but eventually got out of it and flashed 4.3 ML2. I rooted 4.3 before my problem and followed the instructions and everything worked. Flashed the two different tar files (pwndkernel and orignalkernel) so my wifi was working fine.
Now after I had the problem I can't get wifi working no matter what I try, and I can't flash anything besides the tar kernels but they aren't doing anything to fix my problem. Everytime I try to flash 4.3 so I can start from scratch it fails.
I have tried renaming and deleting wpa_supplicant.conf and that had no effect.
I have also tried doing a factory reset and I still have the same problem.
Any suggestions would help! I've been reading for the last 2 days trying to find something but no one seems to have the same issue.
Dan

dan123dbl said:
A few days ago I tried upgrading to 4.4.2 via safestrap and ran into some problems. Long story short I was stuck in Download mode but eventually got out of it and flashed 4.3 ML2. I rooted 4.3 before my problem and followed the instructions and everything worked. Flashed the two different tar files (pwndkernel and orignalkernel) so my wifi was working fine.
Now after I had the problem I can't get wifi working no matter what I try, and I can't flash anything besides the tar kernels but they aren't doing anything to fix my problem. Everytime I try to flash 4.3 so I can start from scratch it fails.
I have tried renaming and deleting wpa_supplicant.conf and that had no effect.
I have also tried doing a factory reset and I still have the same problem.
Any suggestions would help! I've been reading for the last 2 days trying to find something but no one seems to have the same issue.
Dan
Click to expand...
Click to collapse
Did you try flashing the MF1 modem.bin?

Devo7v said:
Did you try flashing the MF1 modem.bin?
Click to expand...
Click to collapse
I tried downloading it but was unable to (link was bad I think)
Would that work even though im mf2?
I also just tried flashing 4.3 again on a different computer with the right drivers installed and it failed.. I'm kind of lost as to why this is happening.

Just tried flashing modem.bin mf1 and got this
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> modem.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Everything I try and flash fails besides originalkernel.tar.md5

dan123dbl said:
Just tried flashing modem.bin mf1 and got this
Added!!
Odin v.3 engine (ID:3)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
modem.bin
NAND Write Start!!
Transmission Complete..
Now Writing.. Please wait about 2 minutes
Receive Response from boot-loader
FAIL! (Auth)
All threads completed. (succeed 0 / failed 1)
Everything I try and flash fails besides originalkernel.tar.md5
Click to expand...
Click to collapse
Odin is super picky. Make sure you are using the original cable that came with your phone. Try different usb ports, try to uninstall and reinstall the drivers, try different computers. Odin will work, the conditions just need to be right. There are also 2 versions of the MF1 floating around, one works and one doesn't.
Unfortunately the only thing I can tell you it's too keep trying, it will eventually work.
EDIT: Here's the correct modem file. http://forum.xda-developers.com/showthread.php?p=52001518

Devo7v said:
Odin is super picky. Make sure you are using the original cable that came with your phone. Try different usb ports, try to uninstall and reinstall the drivers, try different computers. Odin will work, the conditions just need to be right. There are also 2 versions of the MF1 floating around, one works and one doesn't.
Unfortunately the only thing I can tell you it's too keep trying, it will eventually work.
EDIT: Here's the correct modem file. http://forum.xda-developers.com/showthread.php?p=52001518
Click to expand...
Click to collapse
I was able to flash the mf1 modem you linked succesfully. Still no wifi though! Would it be worth trying to get a hold of an at&t sim card to update to 4.4.2 through the network? (I'm on rogers)

dan123dbl said:
I was able to flash the mf1 modem you linked succesfully. Still no wifi though! Would it be worth trying to get a hold of an at&t sim card to update to 4.4.2 through the network? (I'm on rogers)
Click to expand...
Click to collapse
There is no network update anymore, AT&T pulled it because it was messing up people's phones.
I don't know what to tell you, maybe try completely wiping the phone and flash the ML2 package again? It could be a hardware issue and in that case you'd have to send it in for warranty.

I wiped the phone and I was still unable to flash the ml2 package. I'm able to flash the modem.bin. I just can't flash any full packages for some reason. I have tried 3 different usb cables, including the one that the phone came with. I've tried 2 computers, and 3 different versions of odin.
I find it odd that I can flash modem.bin or originalkernel.tar but I can't do a complete package...
I bet it's something simple but I just can't figure it out.
I'm not sure how it would be a hardware issue since it happened right after I messed up going to 4.4.2. The wifi button just won't toggle, every time you go to turn it on it quickly goes back to off.
EDIT:
Right after I typed that I thought of something to try and it fixed it.....
In the whole odin package for 4.3 I decided to single out just the CP file and try to flash that since that's the modem file for the package.
After i flashed that it worked perfectly :silly::silly::silly:
Still have no idea why I couldn't flash the entire package but I will leave it alone for a while before I try and get to 4.4.2 again.
Thanks for all your suggestions!

You're a genius!
Thanks, it works!
dan123dbl said:
i wiped the phone and i was still unable to flash the ml2 package. I'm able to flash the modem.bin. I just can't flash any full packages for some reason. I have tried 3 different usb cables, including the one that the phone came with. I've tried 2 computers, and 3 different versions of odin.
I find it odd that i can flash modem.bin or originalkernel.tar but i can't do a complete package...
I bet it's something simple but i just can't figure it out.
I'm not sure how it would be a hardware issue since it happened right after i messed up going to 4.4.2. The wifi button just won't toggle, every time you go to turn it on it quickly goes back to off.
Edit:
Right after i typed that i thought of something to try and it fixed it.....
In the whole odin package for 4.3 i decided to single out just the cp file and try to flash that since that's the modem file for the package.
After i flashed that it worked perfectly :silly::silly::silly:
Still have no idea why i couldn't flash the entire package but i will leave it alone for a while before i try and get to 4.4.2 again.
Thanks for all your suggestions!
Click to expand...
Click to collapse