I'm new to the captivate.. was going to flash a rom, following thru the instructions im at the point where im flashing back to stock rom with the odin3 oneclick downloader.. but its been just sitting at this for about 20 mins now...
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
Is this normal time to take or should i be worried..? and if its stuck what do i do?
Check your drivers and restart your computer is a good place to start
Sent from my SAMSUNG-SGH-I897
You have to quit ODIN. You aren't in download mode, or you haven't done everything in the correct steps. The page isn't very clear, so it's no problem
Here's what you have to do:
Turn your phone off.
Take out the battery, SIM card, External SD card
Put the battery back in.
Hold down both of the volume rockers.
THEN put in the USB cable (while ODIN is open)
Continue to hold down the volume rockers until your phone is recognized by ODIN
I'm trying to revert to stock jf6 with odin one click downloader from continuum 5 RC3, The phone was put in download mode with volume down+power combo and recognized fine, afer I clicked start it reads as follows:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
And now it's stuck, (about 20 minutes as I'm writing)
Now the "DO NOT TURN OFF TARGET" frightens me, should I wait? I'm guessing it's not the safest thing to unplug it right now..
I've used odin before and never has it taken this long.
Help appreciated.
You have no choice but to unplug
Pull battery
Restart computer
Open odin
Get into dl mode
Try again
mcord11758 said:
You have no choice but to unplug
Pull battery
Restart computer
Open odin
Get into dl mode
Try again
Click to expand...
Click to collapse
Thanks Giving it a go now.
it sometimes does that. as long as it didnt lock up during pbl or sbl .bin you should be just fine!
I recently purchased a samsung galaxy phone from someone which had a custom lidroid rom in it.
I am trying to revert back the custom rom to stock using ODIN Odin3 v1.3 as well 1.85. Every time, i connect my device with ODIN, it is stuck in set up connection state itself and doesn't go beyond that.
Additional Info:
I am trying this by putting my phone into download mode by pressing volume up + Home + Power.
Also, when i press Volume Up + Home + Power, the phone just keeps restarting.
Please help. I dont like the lidroid rom.
Some more info: I downloaded the mobile ODIN app, but it says Could Not locate CLockWorkMod Recovery. CWM3, CWM4 or CWM5 is required, but then there is an option to download that add-in which leads to an item not found page....
nishanchi said:
I recently purchased a samsung galaxy phone from someone which had a custom lidroid rom in it.
I am trying to revert back the custom rom to stock using ODIN Odin3 v1.3 as well 1.85. Every time, i connect my device with ODIN, it is stuck in set up connection state itself and doesn't go beyond that.
Additional Info:
I am trying this by putting my phone into download mode by pressing volume up + Home + Power.
Also, when i press Volume Up + Home + Power, the phone just keeps restarting.
Please help. I dont like the lidroid rom.
Click to expand...
Click to collapse
Make sure your phone are i9000 !!!
Reflashing the stock Rom xxjvu android 2.3.6 from Samsung for Galaxy S i9000.
1.Switch off your phone ( if not Bricked )
2.Get into download mode by pressing Power + Valume down + home button together.
3.Launch ODIN you downlaoded from above.
4.Connect your phone via USB to PC
5.If Odin shows com:[port number] in ID:COM in yellow colour, your phone is connected to pc, else reconnect
6.Extract the zip file su-i9000 you downloaded http://hotfile.com/dl/140301534/be8872c/I9000XXJVU_I9000OXAJVU_OXA.rar.html.(password: samfirmware.com)
7.Now select files in Odin , click on each tab and select files listed below
PIT –– s1_odin_20100512.pit
PDA –– CODE_I9000XX.....tar.md5,
Phone –– MODEM_I9000XX.......tar.md5,
CSC –– GT-I9000-CSC-.....tar.md5
8.
9.Click start Button now, It starts the Installation Process and then wait for Installation to finish. Your phone will reboot after ODIN displays PASS.
Samtan4326 said:
Make sure your phone are i9000 !!!
Reflashing the stock Rom xxjvu android 2.3.6 from Samsung for Galaxy S i9000.
1.Switch off your phone ( if not Bricked )
2.Get into download mode by pressing Power + Valume down + home button together.
3.Launch ODIN you downlaoded from above.
4.Connect your phone via USB to PC
5.If Odin shows com:[port number] in ID:COM in yellow colour, your phone is connected to pc, else reconnect
6.Extract the zip file su-i9000 you downloaded
7.Now select files in Odin , click on each tab and select files listed below
PIT –– s1_odin_20100512.pit
PDA –– CODE_I9000XX.....tar.md5,
Phone –– MODEM_I9000XX.......tar.md5,
CSC –– GT-I9000-CSC-.....tar.md5
8.
9.Click start Button now, It starts the Installation Process and then wait for Installation to finish. Your phone will reboot after ODIN displays PASS.
Click to expand...
Click to collapse
Thanks for the reply. I did all the things that you mentioned. The ODIN is just stuck with this stack:
<ID:0/004> Enter CS for MD5..
<ID:0/004> Check MD5.. Do not unplug the cable..
<ID:0/004> Please wait..
<ID:0/004> Checking MD5 finished Sucessfully..
<ID:0/004> Leave CS..
<ID:0/004> Enter CS for MD5..
<ID:0/004> Check MD5.. Do not unplug the cable..
<ID:0/004> Please wait..
<ID:0/004> Checking MD5 finished Sucessfully..
<ID:0/004> Leave CS..
<ID:0/004> Enter CS for MD5..
<ID:0/004> Check MD5.. Do not unplug the cable..
<ID:0/004> Please wait..
<ID:0/004> Checking MD5 finished Sucessfully..
<ID:0/004> Leave CS..
<ID:0/004> SetupConnection..
Any ideas y?
nishanchi said:
Thanks for the reply. I did all the things that you mentioned. The ODIN is just stuck with this stack:
<ID:0/004> Enter CS for MD5..
<ID:0/004> Check MD5.. Do not unplug the cable..
<ID:0/004> Please wait..
<ID:0/004> Checking MD5 finished Sucessfully..
<ID:0/004> Leave CS..
<ID:0/004> Enter CS for MD5..
<ID:0/004> Check MD5.. Do not unplug the cable..
<ID:0/004> Please wait..
<ID:0/004> Checking MD5 finished Sucessfully..
<ID:0/004> Leave CS..
<ID:0/004> Enter CS for MD5..
<ID:0/004> Check MD5.. Do not unplug the cable..
<ID:0/004> Please wait..
<ID:0/004> Checking MD5 finished Sucessfully..
<ID:0/004> Leave CS..
<ID:0/004> SetupConnection..
Any ideas y?
Click to expand...
Click to collapse
I also tried removing my battery and reinserting it, but that also didn't help....
Also, Make sure your phone are i9000 !!! what does this mean.. The seller told me that this is the phone model and also, i checked the settings>>about phone and it shows this model number there..
nishanchi said:
I also tried removing my battery and reinserting it, but that also didn't help....
Also, Make sure your phone are i9000 !!! what does this mean.. The seller told me that this is the phone model and also, i checked the settings>>about phone and it shows this model number there..
Click to expand...
Click to collapse
use odin v1.7
you may follow this guide, this is more detail. http://nguyenkieuhung1984.blogspot.sg/2012/01/i9000xxjvu-android-236-upgrade-for_07.html
Samtan4326 said:
use odin v1.7
you may follow this guide, this is more detail. [/URL]
Click to expand...
Click to collapse
Even that didn't solve the problem. I even tried taking out the battery and reinserting it, but the ODIN is still stuck in the same place.
nishanchi said:
Even that didn't solve the problem. I even tried taking out the battery and reinserting it, but the ODIN is still stuck in the same place.
Click to expand...
Click to collapse
Do not connect through USB hub
1) KIES process not running in PC tsk manager
2) Try another port
3) Another USB cable
Could also try uncheck "reset time"
Samtan4326 said:
Do not connect through USB hub
1) KIES process not running in PC tsk manager
2) Try another port
3) Another USB cable
Could also try uncheck "reset time"
Click to expand...
Click to collapse
1) KIES process not running in PC tsk manager: KIES not installed
2) Try another port : Tried
3) Another USB cable: Tried
Tried it all, but still ODIN is stuck in setting up connection.
Also, can you please tell me how does the download screen look like. I am seeing 3 options there: reboot, wipe cache paritioning and wipe system data (except sdcard). Is this correct?
Hey
Try installing CM as it has CWM. Then try Downgrading..
Give it a try since u tried almost everything..
tchindalia said:
Hey
Try installing CM as it has CWM. Then try Downgrading..
Give it a try since u tried almost everything..
Click to expand...
Click to collapse
\
I have tried installing CM, it gives a signature verification failed when i try to flash it.....
nishanchi said:
1) KIES process not running in PC tsk manager: KIES not installed
2) Try another port : Tried
3) Another USB cable: Tried
Tried it all, but still ODIN is stuck in setting up connection.
Also, can you please tell me how does the download screen look like. I am seeing 3 options there: reboot, wipe cache paritioning and wipe system data (except sdcard). Is this correct?
Click to expand...
Click to collapse
To get in download mode turn phone off & press: volume DOWN + home button + power button. On your screen a yellow triangle appears
To get in recovery turn phone off & press: volume up + home button + power button. U see what u described above
You are not in download mode!
This is; hold down+home+power
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Start odin
put all files in odin
Connect cable
Wait for yellow connection
Start
Wait
Done
Sent from my GT-I9000 using Tapatalk 2
RobertSand said:
You are not in download mode!
This is; hold down+home+power
View attachment 1519774
Start odin
put all files in odin
Connect cable
Wait for yellow connection
Start
Wait
Done
Sent from my GT-I9000 using Tapatalk 2
Click to expand...
Click to collapse
Yep, that comend to go to download
and remember nishanchi, if odin stuck on some part of flash, just put some pendrive to other usb it will help
nishanchi said:
1) KIES process not running in PC tsk manager: KIES not installed
2) Try another port : Tried
3) Another USB cable: Tried
Tried it all, but still ODIN is stuck in setting up connection.
Also, can you please tell me how does the download screen look like. I am seeing 3 options there: reboot, wipe cache paritioning and wipe system data (except sdcard). Is this correct?
Click to expand...
Click to collapse
the screen will show you one yellow andriod with downloading.... and Do not turn off Target. if you seeing 3 options is wrong you are boot to recovery mode not download mode.
download mode combo is " power + valume down + home"
Samtan4326 said:
the screen will show you one yellow andriod with downloading.... and Do not turn off Target. if you seeing 3 options is wrong you are boot to recovery mode not download mode.
download mode combo is " power + valume down + home"
Click to expand...
Click to collapse
I am using the same combo as suggested by you and tried everything and everyone has suggested in this post....
When i press Volume UP + Centre button + Power my phone keeps restarting.
Also, you mentioned that 3 options is wrong, but then that is what i get when i press volume down + Power + Centre button....
Also, i see a yellow traingle with android bot and an exclaimation mark inside the traingle... Does this tell you anything about my problem?
nishanchi said:
I am using the same combo as suggested by you and tried everything and everyone has suggested in this post....
When i press Volume UP + Centre button + Power my phone keeps restarting.
Also, you mentioned that 3 options is wrong, but then that is what i get when i press volume down + Power + Centre button....
Also, i see a yellow traingle with android bot and an exclaimation mark inside the traingle... Does this tell you anything about my problem?
Click to expand...
Click to collapse
if you see a yellow traingle with android bot and an exclaimation mark inside the traingle mean you are on download mode, so now you can
1)Launch ODIN you downlaoded
2)Connect your phone via USB to PC
3)If Odin shows com:[port number] in ID:COM in yellow colour, your phone is connected to pc, else reconnect
4)Extract the zip file su-i9000 you downloaded http://hotfile.com/dl/140301534/be88...U_OXA.rar.html.(password: samfirmware.com)
5)Now select files in Odin , click on each tab and select files listed below
PIT –– s1_odin_20100512.pit
PDA –– CODE_I9000XX.....tar.md5,
Phone –– MODEM_I9000XX.......tar.md5,
CSC –– GT-I9000-CSC-.....tar.md5
6)Click start Button now, It starts the Installation Process and then wait for Installation to finish. Your phone will reboot after ODIN displays PASS.
this time you problem should be solved :good:
Try some of these:
1. Install Kies (Kies contains drivers for your phone)
2. Download another version of Odin
3. Try connecting phone to another USB port
4. Try doing the same on some other PC, if your phone starts in download mode and Odin won't install, then it's probably that phone is fine, but your PC or Odin is having trouble accessing to your phone
Heres my problem. I flashed twrp on my device (note 5 tmobile, Model SM-N920T). I then flashed kernel from twrp screen on my device. Now when i hold vol up, power and home it does nothing. wont open twrp or recovery mode. I can get to the download os screen (vol down, home and power). i try to flash the stock firmware onto the device via odin always fails.
as seen below
Added!!
Odin engine v(ID:3.1005)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
SingleDownload.
sboot.bin
NAND Write Start!!
cm.bin
FAIL!
Complete(Write) operation failed.
All threads completed. (succeed 0 / failed 1)
Removed!!
i tried reinstalling usb drivers, still fails the same.
When my phone is plugged in to charge it deplays the battery with the lighting bolt. At the top in red lettering it says “KERNAL IS NOT SEANDROID ENFORCING.”
If i hold vol down, home and power im prompted with the warning screen. instead of hitting vol up for download i hit vol down to reboot. The device getting stuck at logo with the red lettering “KERNAL IS NOT SEANDROID ENFORCING.” at the top.
i have also tried to recover using samsung switch could get switch to recongnize my phone is plugged in.
Any idea on how to restore to default would be great please email me
[email protected]
What kernel did you flashed?
---------- Post added at 02:11 PM ---------- Previous post was at 02:10 PM ----------
Did you unlocked the bootloader first??
Dear All,
It's my first time converting from iPhones to Android. Happy to join this community to learn and share.
It was my first amateur experience flashing my Galaxy Note 9.
Basically, I flashed an incorrect file under BL at Odin after OEM Unlock. Phone was running Andriod 9 and it was a N960N (Korean Model)
I downloaded the BL file from another forum that was supposedly to be flashed inside TWRP.
I was stupid enough to change that zip file into a .tar file.
After a successful flash at BL, the phone seems to be bricked. It is unable to go into recovery or download mode.
Whenever I press power, the following message is prompted "KERNEL REV. CHECK FAIL DEVICE:3 BINARY: 2 (BOOT)
I was stupid. Please advise me. Could it be that the volume down button is faulty? I was having a hard time bringing it to download mode at the beginning. I used recovery mode to boot into download mode and then made this big mistake.
Any solution?
Thanks in advance.
This is the Odin Log
<ID:0/009> Added!!
<ID:0/009> Odin engine v(ID:3.1301)..
<ID:0/009> File analysis..
<ID:0/009> Total Binary size: 8 M
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> NAND Write Start!!
<ID:0/009> SingleDownload.
<ID:0/009> cm.bin
<ID:0/009> keystorage.bin
<ID:0/009> sboot.bin
<ID:0/009> up_param.bin
<ID:0/009> RQT_CLOSE !!
<ID:0/009> RES OK !!
<ID:0/009> Removed!!
<ID:0/009> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
you are flashing older kernal. try to download and install same version of the firmware. Your bootloader version is 3 and your are flashing bootloder version 2. go to sammobile and download stock latest firmware for your device. and flash it through odin. make sure you use odin version 3.13.
Munawar Mehmood said:
you are flashing older kernal. try to download and install same version of the firmware. Your bootloader version is 3 and your are flashing bootloder version 2. go to sammobile and download stock latest firmware for your device. and flash it through odin. make sure you use odin version 3.13.
Click to expand...
Click to collapse
Thank you for taking time to read and comment on my thread. Issue now is that the phone is unable to go into recovery and download mode. Not sure if its the problem physically with the volume down button but the phone is not detected by the PC and unable to enter recovery or download mode.
It is not able to be detected by Odin for me to flash stock files..
Try Samsung Smart Switch on PC .
puddleofmud said:
Dear All,
It's my first time converting from iPhones to Android. Happy to join this community to learn and share.
It was my first amateur experience flashing my Galaxy Note 9.
Basically, I flashed an incorrect file under BL at Odin after OEM Unlock. Phone was running Andriod 9 and it was a N960N (Korean Model)
I downloaded the BL file from another forum that was supposedly to be flashed inside TWRP.
I was stupid enough to change that zip file into a .tar file.
After a successful flash at BL, the phone seems to be bricked. It is unable to go into recovery or download mode.
Whenever I press power, the following message is prompted "KERNEL REV. CHECK FAIL DEVICE:3 BINARY: 2 (BOOT)
I was stupid. Please advise me. Could it be that the volume down button is faulty? I was having a hard time bringing it to download mode at the beginning. I used recovery mode to boot into download mode and then made this big mistake.
Any solution?
Thanks in advance.
This is the Odin Log
<ID:0/009> Added!!
<ID:0/009> Odin engine v(ID:3.1301)..
<ID:0/009> File analysis..
<ID:0/009> Total Binary size: 8 M
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> NAND Write Start!!
<ID:0/009> SingleDownload.
<ID:0/009> cm.bin
<ID:0/009> keystorage.bin
<ID:0/009> sboot.bin
<ID:0/009> up_param.bin
<ID:0/009> RQT_CLOSE !!
<ID:0/009> RES OK !!
<ID:0/009> Removed!!
<ID:0/009> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
i saw that you went to download mode through recovery.
there is the regular way
to go into download mode...
hold vol down + bixby + power.
Using power + Bixby + vol down to enter download mode has never worked for me. Here's an alternative method:
Make sure the phone is off. Plug your cable into your computer, hold volume down + Bixby (do not touch the power button), and plug the other end of the cable in your phone while still holding the buttons.
oddbehreif said:
Using power + Bixby + vol down to enter download mode has never worked for me. Here's an alternative method:
Make sure the phone is off. Plug your cable into your computer, hold volume down + Bixby (do not touch the power button), and plug the other end of the cable in your phone while still holding the buttons.
Click to expand...
Click to collapse
It didn't work... Please help me..
sunmybun said:
i saw that you went to download mode through recovery.
there is the regular way
to go into download mode...
hold vol down + bixby + power.
Click to expand...
Click to collapse
Phone is not responding to (vol down + bixby +power) or (vol up + bixby + power) or (vol down +bixby)
The phone just keeps showing the same thing.....
JJEgan said:
Try Samsung Smart Switch on PC .
Click to expand...
Click to collapse
Thanks for your time to reply but the phone can't be detected by the computer..
Is there any other way to fix it? Open up the phone or something?
Thank you....
puddleofmud said:
Phone is not responding to (vol down + bixby +power) or (vol up + bixby + power) or (vol down +bixby)
The phone just keeps showing the same thing.....
Click to expand...
Click to collapse
The above combination (plug USB cable to PC, press and hold, vol down + bixby + power..... While still holding, plug in the USB cable to your phone) should actually work cause myself that's the only way i get my note 9 N960N into download mode. Try reinstalling Samsung drivers and possibly try changing the USB-C cable you're using.
puddleofmud said:
It didn't work... Please help me..
Click to expand...
Click to collapse
vol down + bixby + power should work. you have to hold all three until the blue screen comes up.
it should not show the samsung splash screen.
start from fresh.
(make sure data cable is ok, try connecting any other phone to check the cable)
uninstall smartswitch and drivers then restart your pc.
again install latest version of smartswitch.
Run odin as administrator.
now plug one end of cable to pc.
press power+bixby+volume down key as soon as phone vibrates plugin data cable and release power key only. it should go in download mode. if not then try this.
plug cable in pc and phone. Then press power+volume down+bixby button as soon as phone vibrates release power key only. it should go in download mode.