Related
I was reflashing my phone, while in download mode, the power went off, and now my phone won't turn on or anything. I think my phone is bricked.
I bought the phone a week and a half ago. Will AT&T accept my phone for a replacement if I say it just stopped working? I have the $4.99/month Wireless Insurance, but won't they deny it when they find out I've been messing with it? What should I do?
Thanks!
Before you take it back, make sure it isn't bricked. Remove the battery, replace it, hold both the volume buttons, plug in the usb and see if it takes you to download mode
Sent from my Samsung SGH-i897
Kaik541 said:
Before you take it back, make sure it isn't bricked. Remove the battery, replace it, hold both the volume buttons, plug in the usb and see if it takes you to download mode
Sent from my Samsung SGH-i897
Click to expand...
Click to collapse
It's bricked. Replaced battery, won't turn on no matter what I do to it.
There's a small scratch on the screen, and the micro USB charging port cover is messed up a bit from something sticky getting in there.
What should I tell AT&T? What's the likeliness of them declining my claim? Can they tell that it's been tampered with even though it's bricked?
Wrong forum. But I would use my insurance instead and tell them it just quit on me...
Try plugging into the computer, remove the battery reinsert the battery. Then hold volume up and power till red text comes on the screen from there switch to holding both volume buttons down and power then when the red text flashes to black release power and continue to hold both volume buttons. That should get you back to the downloading digger bot.
Tehwall said:
It's bricked. Replaced battery, won't turn on no matter what I do to it.
There's a small scratch on the screen, and the micro USB charging port cover is messed up a bit from something sticky getting in there.
What should I tell AT&T? What's the likeliness of them declining my claim? Can they tell that it's been tampered with even though it's bricked?
Click to expand...
Click to collapse
They won't give you a hard time on the software side - to them off is off - they can't tell if you bricked it - they will send it somewhere and have it flashed.
BUT - if there is something sticky in the USB port then they do have grounds to deny your claim - for all they know you poured juice in there.
Good luck.
Get it into download mode and flash it again with odin. Likely not bricked.
Sent from my SAMSUNG-SGH-I897 using XDA App
alphadog00 said:
They won't give you a hard time on the software side - to them off is off - they can't tell if you bricked it - they will send it somewhere and have it flashed.
BUT - if there is something sticky in the USB port then they do have grounds to deny your claim - for all they know you poured juice in there.
Good luck.
Click to expand...
Click to collapse
If there is something sticky there it means he put something sticky there lol.
And also, follow thedamn directions people are giving you man. Your phone isntbricked, I dont even know of anyone who has bricked their phone yet..
Mattwp103 said:
Try plugging into the computer, remove the battery reinsert the battery. Then hold volume up and power till red text comes on the screen from there switch to holding both volume buttons down and power then when the red text flashes to black release power and continue to hold both volume buttons. That should get you back to the downloading digger bot.
Click to expand...
Click to collapse
votum said:
If there is something sticky there it means he put something sticky there lol.
And also, follow thedamn directions people are giving you man. Your phone isntbricked, I dont even know of anyone who has bricked their phone yet..
Click to expand...
Click to collapse
I tried everything suggested, nothing happens. The power went out, while flashing new firmware, now the phone won't turn on no matter what I do. I already tried peoples suggestions.
Tehwall said:
I tried everything suggested, nothing happens. The power went out, while flashing new firmware, now the phone won't turn on no matter what I do. I already tried peoples suggestions.
Click to expand...
Click to collapse
The AT&T screen doesn't come up?
Guys we have been told a gazillion times about this...what does this have to do with Development?! Jesus....
Which firmware were you using at the time and which one were you flashing?
also make sure the battery is charged
prestopasto said:
The AT&T screen doesn't come up?
Click to expand...
Click to collapse
Nothing does, I tried every combo, SIM card in and out, replacing battery, USB plugged in and out, download mode, regular power button, recovery mode, what the guy suggested above; everything.
Not a single thing shows up on the screen.
You glanced over my question.
The version of firmware you were using before the flash and during the failed flash can be very pertinent to the key combination you need to get into download mode =P
Zilch25 said:
You glanced over my question.
The version of firmware you were using before the flash and during the failed flash can be very pertinent to the key combination you need to get into download mode =P
Click to expand...
Click to collapse
I had the stock firmware, installed the JM5 firmware, reinstalled the JM5 firmware, while doing so, they power went off.
Just pressing Volume Down + Power got me into Download Mode everytime.
Edit: And yes, the battery was charged, it was at about 67% when I was flashing the firmware. How can I charge the battery for the heck of it when the phone is dead? Normally when you plug in the USB cable there's a charging animation on the screen. Nothing comes up at all, can a dead phone charge a battery, or does the software need to send the power to the battery?
Honestly I've had flashes fail at varying points during the flash and I've gotten the black screen before, ALWAYS I've been able to get it to work by following these steps:
Pull out everything, SIM, SD, Battery, USB, EVERYTHING
Close Odin (If it's open)
Reopen Odin
Insert battery, hold vol down (If this doesn't work hold both volume buttons NO POWER)
While holding the button(s) plug in USB
Don't touch the power at any point, if this fails and you want to try the other key combo, start the process over completely.
Zilch25 said:
Honestly I've had flashes fail at varying points during the flash and I've gotten the black screen before, ALWAYS I've been able to get it to work by following these steps:
Pull out everything, SIM, SD, Battery, USB, EVERYTHING
Close Odin (If it's open)
Reopen Odin
Insert battery, hold vol down (If this doesn't work hold both volume buttons NO POWER)
While holding the button(s) plug in USB
Don't touch the power at any point, if this fails and you want to try the other key combo, start the process over completely.
Click to expand...
Click to collapse
This man speaks the truth, listen to him.
If your insurance covers damage then destroy the phone and call att and tell them its been destroyed.
if not then it is possible that the power outage could have caused your phone to zap.
Flashing or not if you spilled stuff into the usb port your screwed. Week and a half and you scratched the screen and did that? I have tried to scratch mine with no succes. I say ditch that phone and get a GO phone. And have a mod delete this pointless thread already!!!!
Hi all,
I was flashing between Jf6 and JH7 today, wanted to see if flashing JH7 via different methods would give me a 3 button fix. (If it did fix it then flashing via Kies mini didn't do the job)
Ironically it backfired when Odin froze and I flipped out the battery
(Hey, I've been at the dl screen before when it was doing nothing and it survived!)
I plug the USB in, I get the exclamation screen
Do it with volume keys pressed, still get it
Hold down the volume + power and the screen goes blinking between exclamation and blank. I've tried releasing power keys at each point in those screens
I even took a video incase I'm not doing it right. Odin is running in the background. No USB plug-in 'pings' from Windows, as you can hear.
Anything I can do?
btw my bat build date is 8/13.. that bad week
I'm in Australia (bought phone off ebay) so sending it back to the States will be a bit of trouble.. I'm hoping I can work something out with the ebay seller otherwise I'll buy another cappy and hope someone finds the jtag points I guess.
same here. no button combo method that previous worked is working now. :/
OP, did you see this thread: http://forum.xda-developers.com/showthread.php?t=775911
not working for me, but maybe it'll help you ... ?
Tremere said:
Hi all,
I was flashing between Jf6 and JH7 today, wanted to see if flashing JH7 via different methods would give me a 3 button fix. (If it did fix it then flashing via Kies mini didn't do the job)
Ironically it backfired when Odin froze and I flipped out the battery
(Hey, I've been at the dl screen before when it was doing nothing and it survived!)
I plug the USB in, I get the exclamation screen
Do it with volume keys pressed, still get it
Hold down the volume + power and the screen goes blinking between exclamation and blank. I've tried releasing power keys at each point in those screens
I even took a video incase I'm not doing it right. Odin is running in the background. No USB plug-in 'pings' from Windows, as you can hear.
Anything I can do?
btw my bat build date is 8/13.. that bad week
I'm in Australia (bought phone off ebay) so sending it back to the States will be a bit of trouble.. I'm hoping I can work something out with the ebay seller otherwise I'll buy another cappy and hope someone finds the jtag points I guess.
Click to expand...
Click to collapse
You may also want to try removing and then reinstalling the Samsung USB drivers on your PC.
I've verified there is simply no USB device being registered no matter what OS, the phone is just sucking power.
@The_Bishop: Did see that, exactly the same as yours, plug usb in, get that screen
Anyone want to be awesome and send my Capppy back to Samsung on my behalf?
best method that never dies when i was in your situation......
unplug usb, turn phone off, then put battery in, turn odin on, now hold volume buttons ONLY then insert usb in phone, you will see download mode with odin identifying the port;
hope it worked ?!?!?!?
Believe me I have tried everything. There is simply was and still is no way to enter recovery or download mode on this phone. Its hardware locked!
a little off topic, but how do i find my phones "bat build date" ?
I had the exact same problem. If you do a battery pull.. hold down both volume buttons and plug the usb cable into the phone while it's hooked to PC then it bumps you into Download mode. I did the exact same thing you did and am running froyo at the moment.
Oh.. no power button.. just both volume buttons.
YoungGun821 said:
a little off topic, but how do i find my phones "bat build date" ?
Click to expand...
Click to collapse
Is on the underside of the battery, one facing into the slot.
i.e 2010.08.13
terrigan said:
I had the exact same problem. If you do a battery pull.. hold down both volume buttons and plug the usb cable into the phone while it's hooked to PC then it bumps you into Download mode. I did the exact same thing you did and am running froyo at the moment.
Oh.. no power button.. just both volume buttons.
Click to expand...
Click to collapse
Done that. Exactly what happens in video. Both volume buttons down, plug in usb.. no response, just brick screen.
I had the same problem.. the phone didn't register USB.. have you rebooted the computer? I believe i did that at one point.
terrigan said:
I had the same problem.. the phone didn't register USB.. have you rebooted the computer? I believe i did that at one point.
Click to expand...
Click to collapse
I did try once or twice. From another thread it was also said to disable driver verification on windows startup for x64 machines. which I also did.
Basically I want to hear from someone who:
a) has a captivate that could never enter dl/rescue via buttons, only adb
b) captivate didn't trigger a plug in 'ping' from Windows until they ??
FYI this is a Macbook Pro, and I booted into Win7 x64 Pro for flashing.
Hi I have the same problem..
What I did was this rooted with one click.. loaded Cognition 2.1.6 all was good..I saw the froyo so I thought lets try it. so opened up ODIN put it in recovery mode. with ADB could never get it in the button way.. it started to load and it froze. I didn't disable voodoo and IS THAT WHY I AM STUCK? I have tried every combo changed drivers computer will not see the phone.. is it a AT&T Phone
IS there anyway to fix it?? or can someone make a program to fix this? I would make a big donation if they did!!!
Thanks Forum!!
Yeah I had it in adb mode to enter download mode, maybe that is why it won't start back up.
I've now given the phone to a local mobile repair business, if riffbox or someone comes out with a Captivate rescue soon its probably as a end result of me
I sent mine back to Samsung as well. BTW, I have a battery from 2010.08.12 so I might be in the same boat. Wish I'd have used one of my OEMs to see if that made any difference, but I did not. :/
I have the same issue.
Rooted my phone through adb, which was fine. Couldn't get into recovery/download modes with hardware before then.
Now my phone is bricked, and not detected or even charging via USB.
wtf
If the repair shop cant fix it try this:
1.) Remove Battery, SIM Card and External SD
OR
2.) Press and HOLD VOL UP AND DOWN with USB inserted and THEN slap in the battery.
This worked for me, for some reason inserting the battery last did the trick.
Let me know if anyone finds a solution to this I have tried it all and my computer will not detect my phone. Has Samsung blocked this in there firmware?
Did you try what I posted above?
yep nothing if I could get it to detect in command prompt I could force it but it won't... the button thing didn't even work when the phone worked!
So ....
So I was attempting to flash back to stock with Odin (I was using Assonance 5.2). I turned the phone off, then while holding the volume buttons plugged in the USB like normal. Then Odin said added the phone, then I hit start. And it seemed like it was working just fine, then all of a sudden the screen on the phone turned red. Then the status bar on Odin stopped moving completely (stayed for awhile). So I think I made the next big mistake of just disconnecting the USB and taking out the battery. So now the phone won't turn on. So I'm not sure I hard bricked the phone or what? Anyone have any idea? Thanks!
I've plugged the phone into the outlet charger, still nothing happens. This happened like maybe 15 min ago. No action when plugged in the computer or charger. Can't even boot into recovery I don't think. the power button was giving me some trouble earlier today. whenever I was trying to wake the phone up, it seemed to take a few clicks of the power button to wake the phone. This happened only after I flashed Assonance 2.5, so I wanted to flash to an earlier version of the rom. thanks!
What you want to do is get into Download Mode, and flash with Odin One-Click JF6 to get your phone working again..
Have you tried all the various button combos to get into Download Mode? .
If the button combos don't work, you can always try to build/buy a JIG which will force your phone into Download if it's still possible on your phone.
I've tried to get into download mode, but can't seem to do it. I've tried holding the volume up and down button then plugging in the usb (which didn't work). then i tried the taking the battery out, then holding the volume up and down button and power button, then plugging in the usb, then reinserting the battery, then taking my hand off the power button (which didn't work). what is the JIG method?
edit. ok i have no clue wtf just happened, but i am currently in download mode using odin and flashing back to stock.....this is just too weird.....sooo any rom suggestions?
Look in my signature for an example of a JIG.
norcal einstein said:
Look in my signature for an example of a JIG.
Click to expand...
Click to collapse
cool i'm actually gonna go ahead and get one this things......JUST in case of future screw ups that don't have a happy ending
i clicked on the link but it won't let me go the page. below is the message it gave me.
marefin, you do not have permission to access this page. This could be due to one of several reasons:
Your user account may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.
marefin said:
cool i'm actually gonna go ahead and get one this things......JUST in case of future screw ups that don't have a happy ending
Click to expand...
Click to collapse
Definitely a great idea having the jig. Nor cal can attest to the late night save that jig provided me.
Sent from my SGH-T959D using XDA App
Hey guys,
This is another HELP! post, I recently tried to install the O B S S E S S I O N custom rom. I have installed serendipity before and never had a problem with it. I reverted back to the factory reset and everything appeared ok. Well, I got to the point where I installed the new rom and when it reboots, all I see is the "AT&T World Phone." The sound from the Galaxy S screen plays but it just stays on that same AT&T screen. I was going to go into downloading mode and do the Odin reset but the phone will no longer go into downloading mode. I'm just not sure what to do at this point, so any help is greatly appreciated.
Take out the battery SD and sim connect your phone to the computer and press Vol +- and insert battery. There are a few more key combos (depending on what Bootloaders you have) if none of them work i suggest getting a Jig. You can buy them in Ebay or Mobiletechvideos. You can make one alot faster and probably cheaper with this guide. Even if you are able to get in to down load mode its always a good idea to make/buy a jig to have around.
Thanks, I've tried to get it into download mode the way you described and it just does not want to do it. I had to buy a new Captivate yesterday, so I will probably just bring it back to the store and exchange it with another one, and just claim ignorance to the issue lol
I stand by the Jig though, anyone modding their captivate or any SGS should have a jig around.
prbassplayer said:
I stand by the Jig though, anyone modding their captivate or any SGS should have a jig around.
Click to expand...
Click to collapse
This is true, but you have to hold vol up/vol down BEFORE you insert usb lol. I had the same issue. ended up being kernel was the problem. I was able to get into dl mode with vol up/down insert just fine, though. Like Bassplayer said, get a JIG it's like cheap insurance. Not full coverage, but it isn't going to leave you stranded either
Yeah I saw the Jigs are only $8, I am definitely going to be purchasing one tonight just to have it in case
Twicebak3d said:
This is true, but you have to hold vol up/vol down BEFORE you insert usb lol. I had the same issue. ended up being kernel was the problem. I was able to get into dl mode with vol up/down insert just fine, though. Like Bassplayer said, get a JIG it's like cheap insurance. Not full coverage, but it isn't going to leave you stranded either
Click to expand...
Click to collapse
The other way to do it is while your battery and sdcard and chip are out plug in the usb, then hit the vol up/down buttons, followed by placing your battery in while still holding the buttons.
popfan said:
The other way to do it is while your battery and sdcard and chip are out plug in the usb, then hit the vol up/down battery, followed by placing your battery in while still holding the buttons.
Click to expand...
Click to collapse
This method does work, I had a <PC+PHONE> screen yesterday after a failed bootloader install and this did the trick, got me right back into download mode .
I'm stuck in a pretty crappy situation. The phone is on some weird bootloop. When it boots, the AT&T screen comes up, then some weird multi-colored screen comes on, the phone turns off, and this process repeats.
I know how to put it into download mode, but the phone turns on as soon as I put the battery in. I'm not sure how to have it powered off with the battery in long enough so I can hold the volume buttons down and plug the USB in. If I could at least get into download mode and flash something via Odin, I could possibly fix it.
Any suggestions?
did you try, remove battery, plug in usb, hold power and both volume buttons then insert battery? or even just hold vol down and power then insert battery?
adobrakic said:
I'm stuck in a pretty crappy situation. The phone is on some weird bootloop. When it boots, the AT&T screen comes up, then some weird multi-colored screen comes on, the phone turns off, and this process repeats.
I know how to put it into download mode, but the phone turns on as soon as I put the battery in. I'm not sure how to have it powered off with the battery in long enough so I can hold the volume buttons down and plug the USB in. If I could at least get into download mode and flash something via Odin, I could possibly fix it.
Any suggestions?
Click to expand...
Click to collapse
fractaline said:
did you try, remove battery, plug in usb, hold power and both volume buttons then insert battery? or even just hold vol down and power then insert battery?
Click to expand...
Click to collapse
(psst, he said his power button is broken)
You dont need to use the power buttons to enter download mode. Just hold both volume buttons and plug in usb. Though tbh I haven't had to do it in so long my memory is a bit foggy on whether it was both volume buttons + usb or just volume up + usb. Either way one of those should work. Im pretty sure you should be able to do it without the battery inserted.
When all else fails, jig it. Jig it hard.
Herp derp Captivate Tapatalk 2
fractaline said:
did you try, remove battery, plug in usb, hold power and both volume buttons then insert battery? or even just hold vol down and power then insert battery?
Click to expand...
Click to collapse
Well, the power button doesn't work, so I haven't tried the latter. It's not rooted, so trying to get into CWM wouldn't really do much. When I try to plug in the USB, hold the volume buttons, and plug in the battery last, the phone just goes to the battery charging screen. If I take the USB out.. it stays there.
I'm not sure why the phone turns on by itself as soon as I put the battery in. My sister has the same model, and she has to hold the power button to turn it on. :/
I just turned it on, and it's stuck on the AT&t screen instead of bootlooping. This is the first time it has done this after the bootloop began. Odin recognizes it. Is this ninja download mode? If so, could you please point me in the right direction of getting out of this mess? :x This is my sister's fiance's phone, I own a SGS4G. Really don't wanna risk this phone any more than I already have, lol.
Thanks, guys.
--Edit--
To be more specific, I attempted using this to root the phone, which resulted in this situation. Not sure if that's even helpful, but it can't hurt.
I feel for ya, I hate having hardware issues when a software issues happens..
follow fractaline's instructions: Odin ON, battery out, Good USB cable with good USB port Insert, (this is where it gets tricky), hold down volume up and volume down, whilst 2 seconds later putting the battery back in.
if you see the screen with something that looks like this, http://movilzone.org/files/2011/09/Captivate-Download-Mode1.jpeg
or this,
http://1.bp.blogspot.com/-BwmbWV5u6h8/TvNq1jXT7oI/AAAAAAAAMpU/_Mh4V9LMYd8/s1600/Semi-bricked.jpg, Then you can flash a kernel.
Were you on gingerbread 2.3.5? if so I would recommend this http://forum.xda-developers.com/showthread.php?t=1294477&highlight=corn
if you flash corn there is an option in CWM to install root I believe.
I used to flash the corn kernel all day to fix my 2.3.5 problems.
it really depends which version you previously were running. which is hard to tell since it wasn't your phone... more info needed, i'll be back in the morning. hope this helps.
Oh and on the hardware side of things, you could take the back plate off, the plate under the battery, and clean all the crap out. i find with mine i often get dust particles that interfere with my power button. there is a guide to properly tear down a captivate on xda somewhere... I've posted on it before as well.
or, take your fingernails and try and peel back the plastic on the edge of the glass up by the power button, if you can pull it back enough to blow air in there sometimes you can dislodge/clean out whatever is obstructing the power button.
Edit: if you do get it rooted, bring it up to ICS, it's fantastic up here
adobrakic said:
Well, the power button doesn't work, so I haven't tried the latter. It's not rooted, so trying to get into CWM wouldn't really do much. When I try to plug in the USB, hold the volume buttons, and plug in the battery last, the phone just goes to the battery charging screen. If I take the USB out.. it stays there.
I'm not sure why the phone turns on by itself as soon as I put the battery in. My sister has the same model, and she has to hold the power button to turn it on. :/
I just turned it on, and it's stuck on the AT&t screen instead of bootlooping. This is the first time it has done this after the bootloop began. Odin recognizes it. Is this ninja download mode? If so, could you please point me in the right direction of getting out of this mess? :x This is my sister's fiance's phone, I own a SGS4G. Really don't wanna risk this phone any more than I already have, lol.
Thanks, guys.
--Edit--
To be more specific, I attempted using this to root the phone, which resulted in this situation. Not sure if that's even helpful, but it can't hurt.
Click to expand...
Click to collapse
I think you were not on Gingerbread and you attempted to flash a gingerbread kernel. That is why it is bootlooping. You can flash back to stock (Gingerbread or froyo) and that should solve your issue. I'm trying to download and get the stock froyo kernel for you so you can flash that again. Just an FYI, applying root through CWM would require the use of the power button.
Try flashing this in the PDA in Odin. It is the stock froyo kernel.
https://www.dropbox.com/s/vx5r7hr3iokj764/zImage.tar
@Bacon, it was version 2.2. I can't get to download mode because the phone turns on as soon as I put the battery in. I'm not sure why it does this. Also, I don't get the bricked screen because it just bootloops. The AT&T screen comes on, then this comes on, the phone turns off, and this repeats. I'm assuming that the multi-colored screen would be the SGS screen, or something similar.
Oh and on the hardware side of things, you could take the back plate off, the plate under the battery, and clean all the crap out. i find with mine i often get dust particles that interfere with my power button. there is a guide to properly tear down a captivate on xda somewhere... I've posted on it before as well.
or, take your fingernails and try and peel back the plastic on the edge of the glass up by the power button, if you can pull it back enough to blow air in there sometimes you can dislodge/clean out whatever is obstructing the power button.
Click to expand...
Click to collapse
If it comes to that, I'll definitely keep this in mind.
@Red Wow, I'm stupid. -_- I don't know how I missed the "Requirements" on that page. Thanks, I'll try your .tar now.
--Edit--
Ah, unfortunately that AT&T screen wasn't download mode. I guess I'm just gonna have to keep trying until I finally get it into download mode. I just don't get why it's this difficult.
adobrakic said:
@Red Wow, I'm stupid. -_- I don't know how I missed the "Requirements" on that page. Thanks, I'll try your .tar now.
--Edit--
Ah, unfortunately that AT&T screen wasn't download mode. I guess I'm just gonna have to keep trying until I finally get it into download mode. I just don't get why it's this difficult.
Click to expand...
Click to collapse
You're not stupid. I added that after reading your post to prevent others from getting into the same situation.
As for download mode, if you don't have a jig, try this:
Take battery out
Plug phone into computer
Hold down Volume Buttons
Put battery in
adobrakic said:
@Red Wow, I'm stupid. -_- I don't know how I missed the "Requirements" on that page. Thanks, I'll try your .tar now.
--Edit--
Ah, unfortunately that AT&T screen wasn't download mode. I guess I'm just gonna have to keep trying until I finally get it into download mode. I just don't get why it's this difficult.
Click to expand...
Click to collapse
I can't tell you how many times i flashed the wrong kernel because i didn't read that it was for my version! lol!
that screen is unsettling...
well it's tough to say what to do next... just keep trying for a download mode. I've never used a Jig, perhaps that would be a good investment. Maybe use a one click.. I don't know..
I don't suppose this could be a bootloader issue could it?
EDIT: You're sure you have a reliable USB port/Plug? it's very important that both are good.
Red_81 said:
You're not stupid. I added that after reading your post to prevent others from getting into the same situation.
As for download mode, if you don't have a jig, try this:
Take battery out
Plug phone into computer
Hold down Volume Buttons
Put battery in
Click to expand...
Click to collapse
When I do that, I get to this screen. I'm assuming that's the battery charging screen, but the picture of the battery never comes up, just that refreshing icon.
If I keep holding the volume buttons, the phone seems to turn off in this state. I tried immediately unplugging the USB cable and letting go of the volume buttons once it does this. It stays off (if it's actually off). However, when I hold the volume buttons down and plug the USB back in, it just goes back to that screen. No download mode.
@Bacon
I don't suppose this could be a bootloader issue could it?
EDIT: You're sure you have a reliable USB port/Plug? it's very important that both are good.
Click to expand...
Click to collapse
To be honest, I have no idea if it could be a bootloader issue. I'm knowledgeable of Android as far as a user goes, I know nothing about the OS past rooting it, and tweaking it to OC/UC, etc. Also, I believe that the USB port/plug is reliable. It's the same combo I used prior to bricking it (lol). However, I have about 8 different ports and a few different cables as well, I'll give those a go.
Thanks for the help guys, I really do appreciate it.
adobrakic said:
@Bacon
To be honest, I have no idea if it could be a bootloader issue. I'm knowledgeable of Android as far as a user goes, I know nothing about the OS past rooting it, and tweaking it to OC/UC, etc. Also, I believe that the USB port/plug is reliable. It's the same combo I used prior to bricking it (lol). However, I have about 8 different ports and a few different cables as well, I'll give those a go.
Thanks for the help guys, I really do appreciate it.
Click to expand...
Click to collapse
Man I wish I could help more, i tend to be a hardware guy so i'm not much help other than telling you how to fix you power button... just keep flashing the crap out of it i guess. see if anything sticks...
Open a dos window and go to KK4_Root\Tools (probably on your C:\ drive)
Type:
Code:
adb wait-for-device reboot download
and hit enter.
Now try booting the phone with it plugged in again. If the computer recognizes it during the bootloop, it will issue it the command to boot into download mode.
Otherwise, I would suggest getting a download Jig. It will put you into download mode every time.
@Bacon
All good buddy, thanks so much for your help.
@Red
Holy ****, that worked perfectly. I'm in download mode right now, and am in the process of using a one click to get back to stock.
I'll post back with results.
--Edit--
This is the one click I was using. It won't flash bootloaders at first to prevent bricking, so I'm now in Android system recovery. I'm wanting to get into download mode again, but I guess since it's not in bootloop, the command Red gave me doesn't get me there. I need to get back into download so the bootloaders can be flashed. Any suggestions as to how I could get there again?
the most success I've had is using kies mini up to 2.3.5 and then using corn from there on.
Sent from my SGH-I897 using xda app-developers app
Does it always boot to recovery? You could just pull the battery and then try to let it boot normally.
Sent from my SAMSUNG-SGH-I897 using xda premium
@Bacon
Don't I need the phone to boot up for kies, though?
@Red
Yes. As soon as I put the battery in, the AT&T screen comes on, and then the Android System Recovery <3e> screen comes on.
When I try to plug in the USB, hold the volume buttons down, and plug in the battery last, it simply goes to the battery charging screen. I don't know why it doesn't go to download mode. I've tested the volume buttons in the Android System Recovery screen, both work just fine.
If you could get that power button to work you could try wiping data. That might get it out of that funk.
Try this:
Open a dos window and go to KK4_Root\Tools (probably on your C:\ drive)
Code:
adb reboot recovery --wipe_data
Crap, my computer doesn't seem to recognize the device when it's in the Android System Recovery screen. Should I try prying open the power button and seeing if I can get it to work? Don't see any other way out of this. I wish the soft-key buttons could be used for 'enter' instead of just the power button. :|
adobrakic said:
@Bacon
Don't I need the phone to boot up for kies, though?
Click to expand...
Click to collapse
Shoot, sorry i misread i thought you said you had gotten it partially fixed... my b.
I was just commenting how I'd had the most success using a one click to stock and moving up with kies. I'm afraid you may have to wipe data, which would suck.
Try the power button first. It's really easy taking the hardware apart. Just don't strip the tiny screws.... i only have three of the 6 holding my back plate in. You really don't need them all
Sent from my SGH-I897 using xda app-developers app
Honestly man, at this point, I wouldn't care if I had to repurchase all of the apps that I had if it was necessary to get the phone working. I'll YouTube some instructions for disassembly. Hopefully it'll get me out of this jam.