[Q] Another day another brick or hope not, please help. - Galaxy S I9000 Q&A, Help & Troubleshooting

Hello,
I know there's a lot of brick topics and I looked at them and couldn't find any help. To sumarize. Flashed Dary 10.2 EE and after having freezes and what not went and restored my back up. It restored but boots only to Talon splash screen as that happens to be kernel I was on before Darky. Funny thing is I cannot boot to recovery but I can to download mode. So I set up to flash new firmware with odin and click repartition, that's an obvious solution. The problem is that the phone is not recognized in download mode. But it is recognised when it's on the splash screen. I unplug it put to download mode plug it back in and nada, tried reinstalling drivers kies and what not. Nada. And one more think when off and I plug it, it looks like it is not charging, there's just all gray battery symbol on screen and that's it.
I'd appreciate it if you guys have any suggestions or solutions.
Thanks

hmmm weird.
Have you tried a different USB port ? preferably direct into motherboard ?
Also, what version of odin are you using ? there are several versions, perhaps you could try a newer version and see if that makes a difference ?

azzledazzle said:
hmmm weird.
Have you tried a different USB port ? preferably direct into motherboard ?
Also, what version of odin are you using ? there are several versions, perhaps you could try a newer version and see if that makes a difference ?
Click to expand...
Click to collapse
it simply doesn't show up in device management of the computer when in download mode and it needs to for odin to recognise it regardless of version. Did try different usb port and still nada. Thanks

Fremen567 said:
it simply doesn't show up in device management of the computer when in download mode and it needs to for odin to recognise it regardless of version. Did try different usb port and still nada. Thanks
Click to expand...
Click to collapse
try a different computer... see if that works

Fremen567 said:
Hello,
I know there's a lot of brick topics and I looked at them and couldn't find any help. To sumarize. Flashed Dary 10.2 EE and after having freezes and what not went and restored my back up. It restored but boots only to Talon splash screen as that happens to be kernel I was on before Darky. Funny thing is I cannot boot to recovery but I can to download mode. So I set up to flash new firmware with odin and click repartition, that's an obvious solution. The problem is that the phone is not recognized in download mode. But it is recognised when it's on the splash screen. I unplug it put to download mode plug it back in and nada, tried reinstalling drivers kies and what not. Nada. And one more think when off and I plug it, it looks like it is not charging, there's just all gray battery symbol on screen and that's it.
I'd appreciate it if you guys have any suggestions or solutions.
Thanks
Click to expand...
Click to collapse
First, thing try,try try again ..
If it doesn't work, maybe the issue is with the microUSB port, try cleaning it using cloth dipped in spirit. [had a similar issue , where my phone would charge, when connected via usb, but wouldn't get detected. got solved using this ]
Hope it helps..

Related

Bricked phone after updating to JH7 through Mini Kies

I recently found out I could update my captivate with Kies Mini. I updated and everything went smoothly. Kies told me update was successful and I unplugged my captivate. It was booting up fine until it reached the Galaxy S logo. It kept going through the logo animation for about 2 minutes before it shut off. I took the battery out and tried again. Same result. my soft buttons are lighted up. When I touch them It responds with a blink, but no haptic feedback. What is going on??How can I fix this? I tried using Odin to flash it back to stock but it won't recognize it. Mt phone was stock 2.1 with the Voodoo Lag Fix installed and everything ran fine and then after the JH7 update the phone messed up. I read that Launcher Pro causes problems with this update and you have to select the Touch Wiz UI when doing it which I forgot to do.
Please help, thank you.
Make sure your phone is powered down (remove then replace the battery if you have to), run odin, while holding both volume up and down buttons plug in the usb cable to enter download mode, flash with odin.
opcow said:
Make sure your phone is powered down (remove then replace the battery if you have to), run odin, while holding both volume up and down buttons plug in the usb cable to enter download mode, flash with odin.
Click to expand...
Click to collapse
Ya I did that. I get a failed message in red. I attached a picture showing what it shows me.
hve you tried the one click odin tht takes you all the wy back, or is that what you show in the screen shot? You may want to try a different computer or try a master clear.
j101399j said:
hve you tried the one click odin tht takes you all the wy back, or is that what you show in the screen shot? You may want to try a different computer or try a master clear.
Click to expand...
Click to collapse
I tried master clear, it says failed and then completed but it still won't boot up, the Galaxy S screen stays up while the S is flashing and then it goes black. If I press the power button the soft buttons light up but I can't see anything on the screen.
Hmm. And you are putting the phone in download mode (with the big yellow triangle and a shoveling bot pic) as opposed to recovery mode?
opcow said:
Hmm. And you are putting the phone in download mode (with the big yellow triangle and a shoveling bot pic) as opposed to recovery mode?
Click to expand...
Click to collapse
Yes, download mode with the android shoveling that rock stuff
Weird. The only suggestions I can think of then are, try running odin as admin, try using heimdall to flash.
Edit: if all that fails try a different computer and/or different USB cable.
opcow said:
Weird. The only suggestions I can think of then are, try running odin as admin, try using heimdall to flash.
Edit: if all that fails try a different computer and/or different USB cable.
Click to expand...
Click to collapse
I agree, I have bricked my phone and was able to come back with Odin. Even try downloading it again. Heck try flashing froyo odin one click as well
opcow said:
Weird. The only suggestions I can think of then are, try running odin as admin, try using heimdall to flash.
Edit: if all that fails try a different computer and/or different USB cable.
Click to expand...
Click to collapse
DUDE YOU FREAKING ROCK!!!! THANK YOU!!! (I ran as administrator and it worked this time)
Nice. Glad you got it working.
Word to the wise folks... disable any lagfixes before attempting to update. I had the same issue and had to Odin 1-Click to get it back to stock.

BRICKED 1st post edited.

EDIT:
odin crashed while going back to stock then
my phone will get to download mode buuuuut.. my computer doesnt recognize my phone...
i re-downloaded drivers and the phone is recognized however odin failed the 2 times i got it in dl mode(took about an hour to get it each time)... so i have a jig ordered but with odin not working im not feeling optimistic
nothing seems to happen when its plugged into the wall no battery icon. i reinstalled drivers hoping that would help with no luck.. i just got it back in dl mode after like an hour of it not turning on for me but it doesnt do anything once i get it there.
Get odin3 one click and use it in dl mode. It will brg ur phone back to stock
Sent from my SAMSUNG-SGH-I897 using XDA App
definately problem of bad USB..either cable or port....try using different USB cable or different computer....Use full odin by iCezar...its with minimum risk....specially very beneficial in cases like yours....
my pc doesnt see my phone. thats the issue i cant use odin. and the only thing my phone will do is glow black or go to download mode, idk if its charging but its getting hard to get it in dl mode, multiple tries atm no luck
i have already tried reinstalling the drivers. what are they called so i can delete them and install again rather then just redownload maybe that will help?
.
donks232 said:
my pc doesnt see my phone. thats the issue i can use odin
i have already tried reinstalling the drivers. what are they called so i can delete them and install again rather then just redownload maybe that will help?
.
Click to expand...
Click to collapse
did you always had this problem or just when in DL mode? if you always had this problem then ofcourse something wrong with USB port...but if its only for DL mode then u remove and redownload drivers....
viny2cool said:
did you always had this problem or just when in DL mode? if you always had this problem then ofcourse something wrong with USB port...but if its only for DL mode then u remove and redownload drivers....
Click to expand...
Click to collapse
nope this only happened AFTER my crash on odin. my pc has always seen the phone.
try connecting your phone to pc when odin is already running. See whether it detects. Mine worked this way.
bigbyte.me said:
try connecting your phone to pc when odin is already running. See whether it detects. Mine worked this way.
Click to expand...
Click to collapse
i tried that once of twice
need help
ive got this error after tryimg to bring my phone back to 2.1. any one please help me, my email is [email protected]. igot an error with a black background and showing caution sign between a phone and a computer maybe its brick, need help.
thank you so much for your help.
sorry idont know where to put this.
jvmiralles said:
ive got this error after tryimg to bring my phone back to 2.1. any one please help me, my email is [email protected]. igot an error with a black background and showing caution sign between a phone and a computer maybe its brick, need help.
thank you so much for your help.
sorry idont know where to put this.
Click to expand...
Click to collapse
thats not a big deal, just get it in download mode, and flash it with odin.
EDIT: might as well us this post to say what my computer says with usb since i got in in dl mode again...
USB device not recognized
one of the usb devices attached to this computer has
malfunctioned, and windows does not recognize it.
then something about for assistance in solving this issue click here
this has happened to me acouple times, the first was my fault I pull the usb before odin finished. I could get back into Download mode but Odin would not see the phone and computer would not recognize the phone either, device not recognized.
I tried rebooting, re-installing drivers etc. did not work.
but after an hour or so I finally got it to recognize and odin'd back to stock and back to flashing I was.
this is what I did hope it works for you.
1. disconnect all usb devices
2. un-install captivate drivers
3. reboot computer
4. goto device manager and verify that there is no USB device errors, if there is delete them and reboot again verify again in device manager.
5. install captivate drivers
6. reboot computer
7. start ODIN (DG or iCezars, iCezars is safer)
8. plug USB cable into the computer first (the one that came with the phone not an after market one)
9. hold both up and down volume buttons on the phone
10. plug the usb cable into the phone quickly to get into download mode (if I plugged the phone is slowly ODIN did not recognize the phone no COM, once I did it quick and it picked it up)
11. push START as soon as ODIN shows the COM1, COM2, COM3, COM4 etc (this had to be done quickly too, If i waited ODIN would show the COM but still would not start flashing back to stock)
this worked for me more than once I hope it helps you good luck
oh ok thanks, ill give that a try when i get off of work. i hope my battery doesnt die idk if its charging or not
well no luck even getting back to download mode. i bought a jig so i guess im waiting and trying while i wait.
i keep reading its possible to completely brick if odin fails... did i perma brick?
well a bump of sorts, the jig should come in the mail tomorrow. i miss my phone
jig came in the mail, im working on a few failed odin3 attempts but as i freaked out and started typing this post it seems like a great success. the jig works wonderful
donks232 said:
jig came in the mail, im working on a few failed odin3 attempts but as i freaked out and started typing this post it seems like a great success. the jig works wonderful
Click to expand...
Click to collapse
I have not had to do this but I know some others had issues with Odin and had to right click on Odin and run as administrator for it to work. Also the Odin 1 click should work in almost any situation to get you back to stock. The only worry (again never had the problem) is that depending on the build version of the phone you could lose the three button recovery. Look for the Odin that DG posted.
Sent from My KickAss Captivated CM7 OC'd 1.4Ghz/Undervolted
Just bricked mine... had a problem with kies mini while updating to official 2.2, had to enter download mode to return to stock but Odin failed and now this piece of **** won't even turn on nor enter download mode.. ****ing bad luck?
Toddyn said:
Just bricked mine... had a problem with kies mini while updating to official 2.2, had to enter download mode to return to stock but Odin failed and now this piece of **** won't even turn on nor enter download mode.. ****ing bad luck?
Click to expand...
Click to collapse
Did you try a jig?

[Q] Big problems with my Galaxy....Help needed!!

Since yesterday my Galaxy S got stuck. It doesnt start anymore.
What happened?
I flashed my rom to the newest ICS. Everything went well and I used it a couple of days. Yesterdaymorning I did wiped the battery stats and cleared the Davik cache. I rebooted and it got stuck in the bootscreen.
I tried to got in recoverymodus but that was not possible. Bootscreen was all I saw.
Then I tried the downloadme. That is working BUT odin did not see my phone and KIES did also not recognize it. I have the right drivers. When my phone was working it was also not recognized because I am afraid the USB port is not good anymore.
Does anyone have tips?
wvawijk said:
Since yesterday my Galaxy S got stuck. It doesnt start anymore.
What happened?
I flashed my rom to the newest ICS. Everything went well and I used it a couple of days. Yesterdaymorning I did wiped the battery stats and cleared the Davik cache. I rebooted and it got stuck in the bootscreen.
I tried to got in recoverymodus but that was not possible. Bootscreen was all I saw.
Then I tried the downloadme. That is working BUT odin did not see my phone and KIES did also not recognize it. I have the right drivers. When my phone was working it was also not recognized because I am afraid the USB port is not good anymore.
Does anyone have tips?
Click to expand...
Click to collapse
can you go to recovery?
unfortunately not.
if i do the 3button trick the sreens stays on the bootscreen.
Change your drivers to the Nexus drivers in OP of TH ICS thread and try a different USB port.
Once in odin flash the initial CM7 kernel without reboot then go into recovery and reflash CM9.
installed nexusdrivers.
still nothing happens.
any other suggestions?
thx for the help!!!
Different USB port?
tried all 4 and another laptop
also used different cables.
almost start crying
-prereq-
install samsung drivers for your device and windows install type (x32/x64). It's quite important that you install 64 bit drivers on a 64 bit box and not 32, because they are ****ty and work 7/10 times used.
1. be sure to use the same port.
2. be sure to use ONLY the original cable that came with your phone
3. Make sure your phone is able to enter download mode. (Vol down+Home+Power)
if it does, it should install your drivers without issue about then.
4. If you can't use odin to restore your pda/csc/modem, then use heimdall. If that fails, you need to commandprompt heimdall into flashing with 512.pit + required files (refer for help to the heimdall readme included in their install) file after unpacking pda,modem,csc into the heimdall commandline exe.
If 4 does not work you need to unbrick it via 1clickbrick. It's a jar file you donwnload, dblclick and use.
thx for trying to help me. but I am afraid my USB port (mini) on my galaxy is not working. Tried 4 computers, several drivers but stil no connection possible.
Any other suggestions?
wvawijk said:
thx for trying to help me. but I am afraid my USB port (mini) on my galaxy is not working. Tried 4 computers, several drivers but stil no connection possible.
Any other suggestions?
Click to expand...
Click to collapse
Did you indtall usb drivers?
Sent from my GT-I9000 using XDA App
Try flashing the EZBase with Odin in Download Mode. Then report back
Sent from my GT-I9000 using Tapatalk
thx but the problem is : odin does not work.... it does not recognize my phone.... and I use the right drivers....
can it be because I work on isc rom?
When i was on ics (bootloop), ich have downloaded the Samsung USB drivers (exe.) and flashed via odin jvu...
Sent from my GT-I9000 using XDA App
@ aakaashjois
damn....it didn't work with the EZbase pitfile.....:-(
Unusual
wvawijk said:
@ aakaashjois
damn....it didn't work with the EZbase pitfile.....:-(
Click to expand...
Click to collapse
Are you sure? did your phone appear as 'added' after you out it in d/l mode? follow these steps...this is a sureshot method dude.
http://www.theandroidsoul.com/ezbase-ezrom-for-android-2-2-install-revert-back/
Good Luck!
any of the computers find it as new hardware?
amadeus_l said:
Are you sure? did your phone appear as 'added' after you out it in d/l mode? follow these steps...this is a sureshot method dude.
http://www.theandroidsoul.com/ezbase-ezrom-for-android-2-2-install-revert-back/
Good Luck!
Click to expand...
Click to collapse
No added unfortunately..... starting to give up.......
hackandmore said:
any of the computers find it as new hardware?
Click to expand...
Click to collapse
Nope..... I am afraid I lost my Galaxy...... :-(
Had the same problem on Windows machines - for some reason two of my Windows powered computers stopped recognizing my phone. Tried different drivers for no effect, so I gave up and tried it on linux and successfully flashed new kernel using heimdall.
I don't know if this is a legitimate solution because it's like going around the problem instead of solving it, but if everything else fails, try different operating systems.
try charging it..does it charge?
if it doesnt then go in a service and ask them to take a look at it.they will do that for a pack of cigarettes in their extra time.if its fixable and cheap(dont think of replacing the entire motherboard...sell this one for parts and buy another one, or find one with broken display and take em both to a service and tell them to replace the screen from your phone to the other)

[Q] Boot loop without recovery and download mode

Hello everybody!
I've tried to find a solution, but without success.
Today I tried to install CWM on a french Galaxy S.
I've rooted the phone with z4root and after I started on download mod with adb.
Then with Odin3 I installed this file "Root-XX_OXA_JVK-v2.7-CWM3RFS.tar".
After that the phone rebooted automatically, unfortunately it's rebooting eachtime on the galaxy s logo.
The problem are that I can't boot on download mod or on CWM.
When the phone is off and I plug it on charger, it doesn't charge!
I think my phone is bricked.
Do you think you can help me or it's dead?
Is there a hard reboot procedure or something like that?
Thanks
I have exactly the same problem!
Are you sure you can't enter recovery? Volume up+home+power.
Sent from my GT-I9001 using xda premium
Yes i'm 1000% sure!
I can acess the Download Mode, but Odin/Heimdall does not recognize the USB connection...
Keep Trying
I know this is weird but keep hard resetting it. Try like 20 more times before you give up. Worked for me in the past I know it is weird. I had just flashed a new factory ROM.
I swear i have tried to enter the Recovery 20-30 times!!
It's fine
Hello,
I've bought an USB JIG for my SGS GT i9100 and I've been able to install ICS SLIM using Odin v3 1.7.
Very easy...
I advise this solution..
Thanks for your help.
Italia99 said:
I swear i have tried to enter the Recovery 20-30 times!!
Click to expand...
Click to collapse
did u try vol down + home + power button to go to download mode? if it can do that, the problem is just find some driver to make odin recognize your phone. search for "usb driver for samsung galaxy s" in google
then you can bring back your phone to live by downloading any rom you want and flash it via odin
ps. but if you cannot go to download mode, JIG USB with 301 K ohm will help you look at http://www.youtube.com/watch?v=Rdn5GoRjhn0
Same problem here, I actually didn't see this in my search and made a new thread about it (feel free to delete). My computer had KIES on it so it had the drivers already and it's the same computer I went through the download mode before with so I have the drivers. I tried to reinstall them but still nothing.
I fear I may need to buy out my contract :crying:
Tical84 said:
Same problem here, I actually didn't see this in my search and made a new thread about it (feel free to delete). My computer had KIES on it so it had the drivers already and it's the same computer I went through the download mode before with so I have the drivers. I tried to reinstall them but still nothing.
I fear I may need to buy out my contract :crying:
Click to expand...
Click to collapse
I am sure that I am right with this. "If you root, do not use KIES" so you have to uninstall KIES and download separate USB driver.
Then it should see your phone when connect with ODIN
Hope you got your phone back alive soon
USB Connection
Italia99 said:
Yes i'm 1000% sure!
I can acess the Download Mode, but Odin/Heimdall does not recognize the USB connection...
Click to expand...
Click to collapse
Did you checked usb drivers, if not try to connect another samsung android device to your pc first. if another phone connected properly then problem in your phone only.
i suggest check this thread, if you think you completely lost your device - http://forum.xda-developers.com/showthread.php?t=819551
coepeq said:
I am sure that I am right with this. "If you root, do not use KIES" so you have to uninstall KIES and download separate USB driver.
Then it should see your phone when connect with ODIN
Hope you got your phone back alive soon
Click to expand...
Click to collapse
Sorry, I should have been more specific. When I reinstalled the drivers I had actually uninstalled KIES and installed just the drivers.
I do have an update though but still can't get it to boot completely. Late last night I decided to try to get download mode to work one last time before passing out and pressing Vol-, Home and Power actually brought me to the recovery screen for the first time in my phone's life! "F YA!" was the only thing I could think at the time so I first went through and formatted/wiped every option I could find then installed the CM9 that I knew worked and now I get to the alien with the matrix-esque background and it stops there. I plugged it in and left it on that screen all night and that guy was still staring at me this morning. I tried download mode again but my computer still doesn't recognize it.

Captivate problem

Samsung Captivate I897 Devil3 kernel
Slimbean Rom
Stuck on either battery screen(batttery wont show up) only circle icon or at&t world phone screen
Tried button Combos as well as jig still wont change from Batteryscreen
any advice greatly appreciated
I dont know if this is the right place but I am desprate I have looked and looked for possible answers nothing worked....
Finally got it into download mode but computer did not detect unplugged phone now its stuck in cell ! computer icon and phone
turns on automatically when battery is inserted
The phone ! Computer screen is download mode. This has happened because the last time you tried to use Odin the cable was pulled to soon. Open the Odin one click your trying to use while the phone is on that screen, and plug in the USB. If Odin does not recognize it you can look here for connection issues.
http://forum.xda-developers.com/showthread.php?t=1953930
Captivate PC Connection Issues, Download Mode and Recovery Mode Help
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
robm1911 said:
The phone ! Computer screen is download mode. This has happened because the last time you tried to use Odin the cable was pulled to soon. Open the Odin one click your trying to use while the phone is on that screen, and plug in the USB. If Odin does not recognize it you can look here for connection issues.
http://forum.xda-developers.com/showthread.php?t=1953930
Captivate PC Connection Issues, Download Mode and Recovery Mode Help
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
Click to expand...
Click to collapse
I apprecciate it but its still a no go Heimdall doesnt even work, tried reinstalling drivers, tried all button combos, my phone turns on automatically when battery is inserted, Jig does not work either, dont really know what to do at this point
Damienwindigo said:
I apprecciate it but its still a no go Heimdall doesnt even work, tried reinstalling drivers, tried all button combos, my phone turns on automatically when battery is inserted, Jig does not work either, dont really know what to do at this point
Click to expand...
Click to collapse
Heimdall and Odin won't work on same USB port. Have you tried using a different one?
Kinda a shot in the dark but if you haven't tried it yet, put the jig in before the battery. Or try the jig a couple times (wait like 20-30sec in between) with the battery in, that worked for me before.
Odin help
Hey Guys... I am trying to see if anyone can help me figure out the problem with my phone.. i currently have the stock rom running 2.2 i897uckb2
Kernel - 2.6.32.9 - Froyo build
Now I have trying to get Odin to recognize my phone when I am in download mode but it noes not show up in the port field. I have been trying both odin 1.3 as well as Odin 1 click...
The funny thing is that Heimdall can recognize the phone on one click but i am trying to get odin to recognize so that i can switch roms... I preffer Odin to Heimdall so if anybody has any ideas it would be greatly appreciated.
By the way if i am not in download mode and the phone is on and I connect it and have odin on, it actually recognizes the phone... so not sure...
Thanks for any help guys...
rheanjd said:
Hey Guys... I am trying to see if anyone can help me figure out the problem with my phone.. i currently have the stock rom running 2.2 i897uckb2
Kernel - 2.6.32.9 - Froyo build
Now I have trying to get Odin to recognize my phone when I am in download mode but it noes not show up in the port field. I have been trying both odin 1.3 as well as Odin 1 click...
The funny thing is that Heimdall can recognize the phone on one click but i am trying to get odin to recognize so that i can switch roms... I preffer Odin to Heimdall so if anybody has any ideas it would be greatly appreciated.
By the way if i am not in download mode and the phone is on and I connect it and have odin on, it actually recognizes the phone... so not sure...
Thanks for any help guys...
Click to expand...
Click to collapse
Have you tried another USB port? My experience with heidmall is that when you install it's own driver, Odin no longer recognizes the phone when you boot into download mode. If for some reason it still doesn't work, I suppose you could uninstall your captivate drivers and re install them.
Ok... cuz really i did feel that it was because of the one click heimdall that the driver might not be recognized... Mind pointing me to how to un install and then re install the driver on the phone...?
Thanks again for the quick response.
rheanjd said:
Ok... cuz really i did feel that it was because of the one click heimdall that the driver might not be recognized... Mind pointing me to how to un install and then re install the driver on the phone...?
Thanks again for the quick response.
Click to expand...
Click to collapse
Heimdall installs it's own drivers to the USB port you use it on. You will have to use another USB port if you wanna use Odin (Your pc should have more than one).
You could uninstall the drivers but it is far more complicated than just using a different USB port.
location GPS antenna on i897. Well, then disassemble the phone and the antenna to be under the speaker if the speaker remove the antenna located in the top right corner of the board. Who can come up with how to enhance signal reception, write.
^
Answered in ur other post...
Sent from my SGH-I777 using xda premium

Categories

Resources