{FIXED} take a look at this bricked galaxy tab, repairable? [FIXED] - Galaxy Tab Q&A, Help & Troubleshooting

basically i messed up the bootloaders now it does this (bear with me)
http://www.youtube.com/watch?v=QkFsZK79XYQ
it only does this when plugged into the wall and it will not do anything if plugged into usb port on the pc, my guess now is the battery is so flat that it wont do a thing any more! i almost got it to run via odin on the pc but the battery drained so bad that it wont respond, i have left it plugged in for at least 6 hours with then just the same response just on and off on and off.
can i take the battery out and charge it via a separate charger to get some life into it to then flash the stock rom via odin?
any ideas would be great! i don't mind taking it apart but don't want to if i'm going to fry the battery i have all sorts of wall chargers, can i join the + and - from the wall charger to the correct wires on the battery for it to charge? i have a multimeter to test the batteries voltage. any suggestions?
[UPDATE 1 ] flashed overcome stock rom then pc wont connect to odin even in recovery mode, :recovery is stock: :rom is stock: from the overcome website, cant flash any rom via odin as it wotn connect, error message usb device not recognised' how to fix this issue? maybe update.zip via sdcard within stock recovery? which rom and for gt-p1000 united kingdom. i tried to reinstall samsung kies for the correct driver but still the same issue, cannot connect after flashing. i have been following this guide http://p1000.teamovercome.net/?page_id=64 any help with connection would be great or flashing via recovery, almost unbricked but not quite.
my connection problem was due to a faulty usb cable, all is fixed now and i have overcome kratos.installed and running sweet

Hello, I don't think that you have a dead battery. I think your rom has a defect cause your Tab would like to boot. Is it possible to go to recovery or to the download mode? Try to flash something. Does your Tab start this screen flash automaticly by plug on a PC od starts this only if you try to turn it on?
PS: It is possible to remove the battery but it is a little difficult. My suggestion: don't touch the Battery

will not go to download mode or recovery. no response when pushing power power button, all i get is the flashing screen with pc and mobile phone connection.

i left tab connected to the pc for one hour, the tab came on with the pc-phone connection image, i flashed overcome rom via odin with repartition which completed but when it went to reboot it has stayed turned off and wont come on at all even when pressing the power button, no download mode and no recovery, i will wait again for it to come on and try the stock rom, not sure if i've got the correct bootloaders or not.
any ideas?

Have you tried leaving it on the ac outlet? or car charger?

ok slight update. . .
i left it plugged into the pc after it passed the odin flash it then BOOTED i was like WWWAAAAAAHHHHOOOOO bouncing on my chair and feeling very happy indeed the battery is totally dead but is now charging in the wall switched off to get some life back into the battery im so pleased
next steps is to get the overcome rom to flash!

lexriley said:
Have you tried leaving it on the ac outlet? or car charger?
Click to expand...
Click to collapse
i tried for 6 hours to plug it directly into the wall but nothing worked.

Exact same thing happened to me on the Sprint Tab. Called Samsung and sent the unit in. They sent me a brand new unit the next week.

when plugged into my pc now i get an error message, ' usb device has not been recognised' im thinking its the drivers but not sure where to get them, i have searched.
i have updated the 1st post with more information on this issue.

Your tab was showing a secondary bootloader so if you mess up your primary bootloader with the bootloader patch it'll still be recoverable and as for getting overcome I would recommend upgrading to gingerbread which doesn't have protected bootloaders and flash kratos or Jupiter which are faster than the froyo based overcome rims ;-)
Sent from my GT-P1000 using XDA Premium App

Roms*
Sent from my GT-P1000 using XDA Premium App

the only issue im having now is the fact that the pc wont recognise the android phone when in download mode.
the only message i get on the screen is 'usb device not recognised' i am then unable to flash a different rom or a stock rom via odin being gingerbread or froyo. thats why im asking if there is an update.zip file that i can flash from the recovery to make the usb mode work as it wont even work with debugging mode on or off and wont show via samsung kies or odin when the tab is booted.

my connection problem was due to a faulty usb cable, all is fixed now and i have overcome kratos.installed and running sweet

good troubleshooting!!! I
Sent from my GT-P1000 using XDA Premium App

Related

[Q] sgs-Is this a problem I can fix or take it to a center???

My phone was acting up so I restarted the phone and it gets to the samsung galaxy I9000 screen an shuts off. When I connect it to my PC or a wall outlet via usb cord, the battery charge screen comes on for a sec and goes blank and back and so on.....it wont charge. I tried the hard restart and it doesnt work and when I try the download mode it goes to a yellow screen with a triangle. It says downloading....
Not sure if thats working properly.
Is this a problem where I can flash my phone and fix this.
Because sending my phone off to a center would take forever.
Any advice would be greatly appreciated. Thanks.
Well first of all your download mode is working fine. For your problem i have few questions: does your pc recognize your phone and can you charge it. Have you bought it with that problem or it has suddenly happened? I think that this is a hardware problem but we should wait for other opinion
Sent from my GT-I9000 using XDA App
If your phone was hacked before (rooted, flashed new firmware), you should reflash it with a clean firmware (or ask someone who has experience). If not, that might be a virus which rooted and damaged your software. There were some of these in the market. This could also be repaired by flashing. But you'll lose your warranty.
You have a "boot-loop". Your download mode is working. So you can flash stock firmware. Find your country specific firmware and use ODIN! But please read up on which version of stock you have to flash.

Bet this can't be fixed

No firmware and USB problem
I have a large problem, my wifes galaxy s won't go by the first screen (says GALAXY S GT-I9000)
So i thought i'd fix it using odin using the 3 button combo. But that isn't working anymore.
Luckily i have a usb jig which gets me to the download mode ...... but !
When i connect the pc cable (tried 2 OE samsung ones) i get device not recognized so i can't use odin to fix it.
What can i do, or do i have to send it to a repair centre to be resurrected ?
I have searched and searched but not found any topics with the same issues i have on her phone.
Need a bit more info i.e were you flashing the phone??if so which rom?
Then phone was playing up so i flashed darkys 10.4.2.
However the usb connection wouldn't work so i flashed it to standard JVT
using mobile odin.
Then i rooted it and went to go into recovery mode and it wouldn't turn on.
I tried to help the gentleman , but no luck . From what he told me , phone turns on after battery insertion , and It is not recognised by usb => so odin not usable .
If you can get to download mode but the phone isn't recognized by your computer then i'd say it's a driver issue. Install your phone's drivers again. To do that, just installing kies is enough BUT be sure to open task manager in windows and kill any process that has kies in it's name before opening odin.
If that still isn't flying i'd try using different USB ports and even with a different computer.
Extra advice:
- try not to flash bootloaders for now. That means picking a rom that has no bootloaders included but matches your phone's current bootloader. If you were using gingerbread flash a gingerbread rom, if you were using froyo, flash a froyo rom.
phone not starting up past first screen (GALAXY S GT-I9000 in white on black screen), phone not recognized neither by pc nor laptop ( usb drivers installed ) , phone turns on after battery insertion without pressing anything.
This manual is from a German board
Take the battery out, then hold the 3 keys combo for download and put the battery back on. Now you should start the download mode.
If not, then try it with a jig.
Good luck!
GOT A JIG. WORKS FINE.
But pc wont recognize it !!
Have you double checked that you have the right drivers installed? I know you have to use the Nexus S drivers for CM9, not sure about Darky's ROM.
Drivers
Download drivers 64 bit | 32 bit from here and install.
It is NOT the drivers as my other galaxy s connects fine every time.
Drivers have been removed and installed repeatedly.
I would suggest a different computer, maybe a different cable. I have this same issue with my infuse, hope you get this resolved.
Sent from my Desire HD using XDA App
Already tried that as well
You could try Adam outler's unbrickable mod.
Pasted from other thread:
I just wrote a wall of text b4 and my browser crashed GG
Well, here we go again, i will only tell what I did/the process
I did a nandroidbackup, then i wiped all data (data+cache+dalvik), installed CyanogenMod 9 (Build 16), it rebooted automaticly, so I entered recovery again, installed Google Apps from there, wiped data and cache (no dalvik), rebooted.
Ended up looping at the Samsung screen (not animation), and I couldnt do the 3-button-combo, so the NANDroid backup is useless.
I can enter the download thing, but i dont even know what it does.
Tried plugging it in the charger (after letting it dry out during the night), and only the loop thing appears. Cant do anything.
I see that theres something called odin (Since my download thing is working (VolDown+Home+Power) if its that you mean.
If its possible to fix my phones state, please tell me how, since I startedrooting, flashing and stuff yesterday (Gotta start at some point) and followed HDTechVideos tut (On his website)
woolf clubs said:
You could try Adam outler's unbrickable mod.
Click to expand...
Click to collapse
I have nowhere near enough ability for that. Pity though.
Your problem is most likely the USB port. Maybe cleaning it might help. It happened to me for a few months then when I got the S2 I stopped using it. Began to use it as my home 3g wifi modem and kept it on charge the whole time. A few weeks later tried connecting it to the computer and it worked first go. Ever since it has worked perferctly. I suspect the problem possibly started by a rain drop getting into the port.
Mind you, even when it wasn't being recognised by the PC, I would constantly connect, remove, reconnect, reboot PC and phone etc and it would sometimes get recognised. Other times it wouldn't connect but Odin still recognised it.
Sounds silly but try leaving it on charge as I did and maybe, just maybe you'll be lucky like I was.
Sent from my GT-I9100T
Well as of today it is away to the O2 repair centre.
Its under warranty (unless the find out it was rooted etc) so fingers crossed.
Well had a text back today to say my phone has been despatched, so here is hoping that its fixed.
It came back from the repair centre yesterday with a note saying a part had been replaced,
no costs for me, yippeeeeeeee.

[Q] Is my phone dead after flashing on rom manager installed clockwork mod

I have been flashing roms and kernels on my note since the day I got it on release.. Could say I'm bit of a flashaholic, but Friday I made the mistake of not using a SAFE kernel from xda but installed clockwork mod recovery from rom manager.. After I wiped data and proceeded to flash a custom rom my phone turnt off and I haven't been able to turn it back on. I can't get into recovery or download mode. My pc is picking up the phone but is throwing out USB not recognisable errors.. Could this be the dreaded hard brick and would a Samsung jig be my way out of it?
u said while flashing the rom the phone went off.. could it be possible that the battery is dead?
The battery was fully charged whilst flashing... And since it happened I have had my phone on charge whilst at work to see if that was the fault.
If phone is taking charging den use jig.
Hit thanks button please
Sent from my GT-N7000 using xda app-developers app
I have no charge screen on the note but my charger has LEDs on to show charging. Should there be a charge screen whilst bricked?
it depends.. if its hard brcked then no just black screen
Thanks a lot. I'm sure with my pc throwing out USB not recognised errors I should be fine when my jig arrives. I'll let you know the results
hopefully. keep us posted

Possibly bricked Galaxy i9000

Hi, i bought a used Galaxy i9000 from a friend and it had Froyo 2.2 installed on it, i rooted the phone with an app on the phone because i couldn't seem to get any response when i plugged it into the laptop via usb lead. The computer will not detect the phone at all it just does nothing when it's plugged in. It will charge from the usb cable and charger but will not do anything once plugged into the computer. I tried using rom manager to install a rom, the last thing on-screen on the phone was saying that it was flashing the kernel, then it rebooted and since then the phone just displays Galaxy i9000 or it will also display a small circular clock type icon in the middle of the black screen and it is a frozen icon. The phone will go into download mode and i have tried to flash it with odin but when in download mode and plugged into the computer, Odin does not detect it, i have tried at least 6 usb cables all tested on my other i9000 and work fine but with this other phone they do not respond. The only thing i can think of is maybe the usb micro port is broken/faulty, what do you think it could be? Any help would be appreciated because i have been trying for hours for the past two days and cannot seem to figure it out, i'm just hoping the phone isn't beyond being repaired. Thanks
Did you install the latest version of samsung drivers?
if not install them, then try to flash again using odin... do it multiple times until you get it right.
and by the way, going into download mode without your computer recognizing your device is a big big mistake... hope it'll work for you
here you can get the latest drivers:
http://forum.xda-developers.com/showthread.php?t=961956
Have you tried in a different computer with automatic windows update switched on?
Sent from my GT-I9000 using xda app-developers app
I have tried installing the latest drivers and also tried on another computer with no response. I have a working i9000 and tested it on both computers with the same user cables and it works fine, do you think the micro usb port is broken? I thanks for the replies
Sent from my GT-I9000 using xda app-developers app
can you get into recovery mode, if you can you may be able to use a sd card to flash from. This depends on what recovery is already on there, have a look at this page http://forum.xda-developers.com/showpost.php?p=30415128&postcount=1
It wont go into recovery mode it just boot loops when i try
Sent from my GT-I9000 using xda app-developers app
Just yesterday I had issues with the latest Samsung driver (1.5.16.0 bricked my phone), so i reverted to1.5.9.0. This seemed to rectify flashing my recently acquired GT-I9000T.
It may help you.
P.S. 1.5.16.0 worked OK on my GT-I9100.
Sent from my GT-I9000 using xda app-developers app
Bern112 said:
Hi, i bought a used Galaxy i9000 from a friend and it had Froyo 2.2 installed on it, i rooted the phone with an app on the phone because i couldn't seem to get any response when i plugged it into the laptop via usb lead. The computer will not detect the phone at all it just does nothing when it's plugged in. It will charge from the usb cable and charger but will not do anything once plugged into the computer. I tried using rom manager to install a rom, the last thing on-screen on the phone was saying that it was flashing the kernel, then it rebooted and since then the phone just displays Galaxy i9000 or it will also display a small circular clock type icon in the middle of the black screen and it is a frozen icon. The phone will go into download mode and i have tried to flash it with odin but when in download mode and plugged into the computer, Odin does not detect it, i have tried at least 6 usb cables all tested on my other i9000 and work fine but with this other phone they do not respond. The only thing i can think of is maybe the usb micro port is broken/faulty, what do you think it could be? Any help would be appreciated because i have been trying for hours for the past two days and cannot seem to figure it out, i'm just hoping the phone isn't beyond being repaired. Thanks
Click to expand...
Click to collapse
Hi , r u able to resolve this issue .. now iam facing the same issue .. my phone boots to download mode but my pc doesn't detect it & i am unable to go to recovery mode.

[Q] Captivate ROM Error

Ok, so I hard bricked my Captivate, used the Radioshack homemade jig to force it into download mode, and flashed Gingerbread 2.3.6 XXJVU. After further research, I realized I wanted to downgrade to 2.3 for a more effective custom ROM flash, so I flashed a stock Eclair 2.1 ROM using Odin one click (with bootloaders, I'm assuming). The flash was successful as far as Odin was concerned, but now the phone gets stuck in a boot loop for quite some time. If I let the loop run its course, it will eventually load the 2.1 ROM, but the phone will power off after about 5 seconds after I plug either a USB cable OR a charger (the charger is recognized as a USB cord by the phone). I cannot get the phone into recovery or download mode; the 10 plus button combinations do not work, and the jig sends it into the boot loop. I even tried holding the volume down key through the entire boot loop sequence, but it never stops (as opposed to not holding the volume down key, where it boots eventually). I tried reformatting the internal SD card, and I looked into putting it into download mode through ADB, but I do not have it installed and even if I did, I can't get the phone to stay on while connected via USB. The computer even recognizes it through USB until the phone shuts off. Through much research, I've come to the conclusion that I must re-brick my phone somehow from within the stock ROM I have installed. I have no idea if this is even possible or if it's the right solution, but I'm at the end of the line at this point. Any suggestions to help with this?
worldextermination said:
After further research, I realized I wanted to downgrade to 2.3 for a more effective custom ROM flash, so I flashed a stock Eclair 2.1 ROM using Odin one click (with bootloaders, I'm assuming).
Click to expand...
Click to collapse
No such thing as "more effective custom ROM flash". All you need is stock GB with GB bootloaders.
You need to get to Download mode and flash stock GB. Tons of information in this forum, please read it.
I've been browsing these forums for days for information on this subject, and none of the solutions I've found fix my problem.
And where exactly did you read you need to downgrade 2.3.x to 2.1 in order to flash a custom ROM?
Calm down, turn the phone off and leave it on a charger for few hours in order to recharge the battery. Disconnect the charger, remove the battery, remove SIM and SD. Reinstall battery only, hold both volume keys and plug the phone to the PC. See Download mode now?
I didn't read that I needed to downgrade, but the guides I was reading were one click solutions for root and flash for 2.3, and I guess should've ignored them and done it manually. I did a one click on a #1110 phone, which is why it's now acting lame, I assume.
Ha, I am pretty calm. I have a Verizon Galaxy S that I've been using to charge the battery, since my AT&T Captivate won't even charge the battery via USB or straight charger when it's off, so it's pretty full. I've tried every method, including the one you just mentioned, and none of them work to bring me to download mode.
Captivate - PC Connection Issues, Download Mode and Recovery Mode Help
4-2ndtwin said:
Captivate - PC Connection Issues, Download Mode and Recovery Mode Help
Click to expand...
Click to collapse
I've had that thread open in my browser for the past 2 days, and have tried everything it suggests multiple times.
^
Have ya tried to make a Jig ?
http://forum.xda-developers.com/showpost.php?p=9238587&postcount=1
The jig I used to get it from fully bricked state into download mode would put it back into the boot loop. I solved my problem with the adb reboot download command. I managed to activate the command before the phone randomly shut off, as it does when I insert the USB cable. Thanks everyone!

Categories

Resources