Related
Need some help trying to figure out how to make my Captivate turn on...I press power and get the AT&T slash screen and then the galaxy s logo loads for about 3 minutes and goes to blank dark screen with the capacitive buttons lit. this is not good because my **** won't boot into recovery either
You should flash to stock then...pull battery, hold volume buttons and plug in usb with odin loaded and ready on the computer. There's plenty of threads to help you out
Sent from my phone so excuse the spelling errors
Funnily enough... My phone just did that too. I was installing Mort Widget and it just totally bricked...
I'm rather p!ssed at this...
Course this was after it deleted all my email accounts and SMS.
What you'll need.
Odin (search or look in any of the ROM/Firmware threads, for example the i9000 ROM or unofficial JH2 or JH3 ROM)
Your USB cable.
The firmware files.
Steps:
Remove battery, SIM card and micro SD card.
Open Odin on the computer.
Put the battery back in.
Plug in the USB cable to the phone.
Hold both volume up and down.
With VOL up/down held in, plug usb cable to the computer.
Your phone will show the beloved DOWNLOADING yellow image.
Odin:
Simply select the rom/firmware you want to flash to and enjoy.
I can confirm this will not overwrite the phone's internal 16gb storage, which is where most apps save backups to.
Future steps:
Before trying anything crazy, copy the entire phone internal 16gb storage to your computer. If you brick, you can always get a new captivate, copy the junk back and run a restore.
I recommend Titanium backup (donate the $6, the backup/restore is SUPER SUPER fast) along with Clockwork recovery. Clockwork's Nandroid makes full kernel backups and you can boot to recovery from the phone itself. No more adb reboot download or adb reboot recovery.
sorry for my english i have a 19000m the one from bell my phone boot with the GALAXY S LOGO WITH THE MUSIC BUT AFTER THAT BLACK SCREEN CAN I REPAIR THAT ?
Yes, odin is about your only hope here... Even if you boot into the bios and try to do a factory reset it will come up with error after error...
Reflashing will totally wipe and start fresh.
I am curious however. I think i isolated where my problem came from but I am still curious...
Did you try to sideload anything?
It happened to me twice with Bell's Vibrant version. The first time, just after one week after getting it (not rooted). They simply gave me a brand new one.
The second one took 3 week to go dead. Knowing my way around Linux Embedded systems, this time I investigated the issue. In recovery mode, there were error messages saying that the system could not fine the internal flash memory partitions. I could confirm from the kernel messages that partitions on internal sdcard had disappeared. I did factory reset, reflash original stock firmware with Odin, but it did nothing.
I Sent the phone back for repair and three weeks later, they gave me another one (probably refurbished!!).
My phone just turns on, with a black screen and the capacitive buttons lit up. Nothing else happens. When I try to go into download mode, it only goes back to this black screen. I does however detect that the phone is connected driver wise on the computer, but does not show up in Hemidall or Odin. I've tried just about everything
i used ODIN to resotore the phont to stock
but when it finsh...i get black screen
and the phone dose not work or do anything.
any help plzzz
isa.ahmed said:
i used ODIN to resotore the phont to stock
but when it finsh...i get black screen
and the phone dose not work or do anything.
any help plzzz
Click to expand...
Click to collapse
Does it light up or display anything and then go black, or does it just do nothing? If it does nothing, you're probably bricked, but try this anyway just in case your phone still has some life in it:
open Odin; press and hold both volume buttons and plug in your USB. If Odin lights up yellow, flash.
If that doesn't work, buy or build a jig, use it, and see if it goes into download mode. If it doesn't, plug the cable in anyway and see if Odin recognizes it. If it does, flash.
If that doesn't work, you're probably bricked. JTAG or Unbrickable Mod are your options from here, neither of which I personally know anything about but you can search around and find someone who can help you.
Hard Bricked= No signs of life, black screen no matter what, no response to USB plug in. Nothing but Unbrickable mod or JTAG will fix, I WOULD SUGGEST getting Unbrickable because you only have to get it once, and it cost the same as JTAG.
Soft Bricked= DL mode access is available(by jig or button combo and usb), recovery too, has some life in it. Can use ODIN/HEIMDALL to fix it.
when the flashing finsh and say done...and show the green light in the ODIN. the phone did not start up
dose this mean it break or dead charger?
as m not shure if the battery is full or not.
anyway i can pass the battery by over it with cuted USB cable?
isa.ahmed said:
when the flashing finsh and say done...and show the green light in the ODIN. the phone did not start up
dose this mean it break or dead charger?
as m not shure if the battery is full or not.
anyway i can pass the battery by over it with cuted USB cable?
Click to expand...
Click to collapse
If you got a green light, I would think it should at least turn on. However, if it was a successful flash, it should charge with the phone off. A bricked phone and a bad charger would both look the same: dead.
Try a different charger or battery if you think your battery could that dead. However if your battery died during your flash, that could also be the cause of your brick.
i charge the battery...and nothing happend
will the USB JAG solve it?
as i read in some post this will not
i need to send to some one to do it by opeing the phont it self
isa.ahmed said:
i charge the battery...and nothing happend
will the USB JAG solve it?
as i read in some post this will not
i need to send to some one to do it by opeing the phont it self
Click to expand...
Click to collapse
A jig is worth trying, but I suspect it will not solve your issue. You are correct, you need to send it to someone to have it fixed. Send a PM to AdamOutler or Connexion2005 and they can point you in the right direction.
what a crapy phone
i had Moto Defy and i never face same issue
so now am end with usellss phone..and need to theough away
what a waist of mony
isa.ahmed said:
what a crapy phone
i had Moto Defy and i never face same issue
so now am end with usellss phone..and need to theough away
what a waist of mony
Click to expand...
Click to collapse
You moto defy never flashed boot loaders since Motorola always had them locked down, and if you didn't know what you were doing flashing the stock Emma's that had boot loaders then it is not the phones fault. You should never really have to flash boot loaders and that is the ONLY risky part in flashing on these phones. Other than that Samsung cappys are almost TRUELY unbrickable (HARD BRICK) unless you mess up flashing boot loaders. WHICH YOU DID WHETHER YOU KNEW IT OR NOT BY FLASHING THE STOCK ODIN. SEND IT FOR UNBRICKABLE MOD, it is cheap repair and you WONT run into your same mistake ever again.
Sent from My KickAss CM7 Captivate
so no way i can do it here?
need to send it?to who i send? and who to trust?
i found some one will do for 50$
http://www.mobiletechvideos.com/blog/?page_id=776
Adam Outler
Sent from my SGH-I897 using xda premium
and other issue, i never toch the bootloader of it
i only re flash the OS of it only..and end with black screen.
this gay he will do what?
can the agent do it?
as it will be easer than to send it
can i have link of who will do it
So I was trying to go from serendipity 6.4 to 7...
I was following the directions on the serendipity site, got to the point where it was supposed to be flashing the new boot loader and gingerbread. Odin sat on "zImage" for about 15 minutes before i decided for some reason that it was frozen and that unplugging it and trying again might help...
now the only thing I can get from the phone is a black screen with red and green dots when i try to get to download mode.
any suggestions??
Elliot
zImage is the kernel. This should recoverable
Did it get passed boot.bin and sbl.bin? If so you've got the new boot loaders. vol down and power to get to DL mode. Since odin hung and was disconnected before completion the image for DL mode might not even be on the phone. Try that combo (or better yet a jig) then whatever screen it boots into hook it up to odin and try flashing just xcals gb kernel. If it's not in DL mode it will just hang on "setting up connection."
studacris said:
zImage is the kernel. This should recoverable
Did it get passed boot.bin and sbl.bin? If so you've got the new boot loaders. vol down and power to get to DL mode. Since odin hung and was disconnected before completion the image for DL mode might not even be on the phone. Try that combo (or better yet a jig) then whatever screen it boots into hook it up to odin and try flashing just xcals gb kernel. If it's not in DL mode it will just hang on "setting up connection."
Click to expand...
Click to collapse
Got it to what is now just a white fuzzy screen (not giving me the black with dots anymore) and the computer doesn't recognize im plugging anything in. about to head to radio shack to source a jig.
Assuming im not completely water-headed, there should be a screenshot of my odin attempt, for your viewing pleasure...
if thats the first fail, then the bootloaders were never flashed so try the old button combo... switch usb ports first of all no matter if you try the next peice of advice or not anytime odin fails you should swap usb ports(always making sure its on the back, no hubs or front ports)...open odin, hold volume buttons and plug in usb chord on your phone...
a jig is always a good idea... i made mine before i ever flashed anything so i knew i would have an out if things went sour.
studacris said:
if thats the first fail, then the bootloaders were never flashed so try the old button combo... switch usb ports first of all no matter if you try the next peice of advice or not anytime odin fails you should swap usb ports(always making sure its on the back, no hubs or front ports)...open odin, hold volume buttons and plug in usb chord on your phone...
a jig is always a good idea... i made mine before i ever flashed anything so i knew i would have an out if things went sour.
Click to expand...
Click to collapse
finally got it to download mode, but now im frozen at "param.lfs" after "firmware update start"...
Thank you so much for the prompt help studa, I really appreciate it
Hmmm...not your day huh? If it's frozen you have no choice but to disconnect. All the damage has been done. When you disconnect now you will most likely get the "clay" screen: phone....!.....pc and like I said before the download mode image might be missing. But this should still be recoverable
What version of odin is that? The earlier versions tend to freeze up more. go to this thread http://forum.xda-developers.com/showthread.php?t=979133 don't worry about the firmwares just at the bottom there is a few versions of odin. 1.7, 1.81 and 1.82 try one of those.
studacris said:
Hmmm...not your day huh? If it's frozen you have no choice but to disconnect. All the damage has been done. When you disconnect now you will most likely get the "clay" screen: phone....!.....pc and like I said before the download mode image might be missing. But this should still be recoverable
What version of odin is that? The earlier versions tend to freeze up more. go to this thread http://forum.xda-developers.com/showthread.php?t=979133 don't worry about the firmwares just at the bottom there is a few versions of odin. 1.7, 1.81 and 1.82 try one of those.
Click to expand...
Click to collapse
Fortunately, I am apparently allowed a few more tries... it keeps letting me go back to download mode after it inevitably freezes at either "param.lfs" or "zImage"...
I tried with 1.82, still no luck...
umm could be the usb chord...
ouch.... a usb cable.... but on the other hand, you are now my hero!
Thank you very much sir, donations ye shall receive
Hi everyone! I have Captivate(1008 batch) with Phoenix Ultimate firmware. Today I tried to flash it with batch Gingerbread. Seems like my mistake was that I forgot to turn off lagfix. Odin halted. Now I'm getting "phone-!-PC" screen each time I connect phone to PC...
I can not get cappy into download mobe(tried all 3 ways)
Odin doesn't see phone...
Do I have any chaces to repair my phone or it's a brick? Is there a chance that jig will help?
There's a new thread in the dev section about a one click unbrick from that screen. I read that it's just downlad the software, plug in phone and click run.
AdamOutler made this -
http://forum.xda-developers.com/showthread.php?t=1153310
Ok, thanks I'll try that! BTW which fimware should I flash if my cappy is back to download mode? As I understand Phoenix formated my phone memory into ext4 filesystem. Is that possible to flash stock Gingerbread on ext4 filesystem?
UPD: Unfortunately software unbrick doesn't help I got "Phone is not connected" message. My PC doesn't see phone at all
The Jig should work, assuming you don't have mixed bootloaders. If you do have mixed bootloaders, JTAG service will be what you need.
If you do manage to get back to download mode, use the JF6 Odin 1-click.
You can get it here: http://forum.xda-developers.com/showthread.php?t=731989
Here's another suggestion that I did with a 1008 that I had a while back. open Odin 1 click to prepare for download mode. (make sure it's not one with the three button fix - if you one click from gingerbread to 3 button fix stock, it is a certain hard brick).
Remove battery, count to 10, replace battery.
hold the vol up and vol down buttons at the same time until you see the screen flash. It should flash every 5-7 seconds as long as you continiuosly hold the buttons.
When you see the screen flash, insert usb cord (with it already connected to computer).
This got me to download mode. It mat take a few tries. sometimes it's a challenge to get to DL mode from this screen. This procedure worked on my 1008. Hope it works.
A jig may work too, but it n ever worked for me on the 1008.
Thank you guys. Hope your suggestions will help!
With the phone and PC screen the Jig will work for sure try and make one or u can buy it.
You can also try this, Remove the battery open odin 1 cick and plug the cable to the usb port at the back of the PC and then the phone and now put the battery see if the odin lits up if yes you are done.
I solved the problem(even without jig). So writing my solution, hope this will help someone.
1) I went home to use another PC. Installed Samsung drivers there.
2) I tried different key combos. Vol Up + Vol Down didn't worked but Vol Down + USB entered Download mode.
3) One guy from russian android forum told me to try with Odin 1 click 2.1 stock firmware. Only this version of firmware connected to my soft bricked phone.
One more time thanks everyone for your replies
For future reference.
If your phone turns on (you can see anything on the screen), then you do not have a perminate brick, and a jig will work.
And your filesystem/lagfix does not matter with odin 1click. It resets everything to the way it came, nomater what you came from. (It even works on cm7 witch repartisioned it and used MTD).
I have the same problem as you. I can't get get the one-click unbrick to work (doesn't detect a device). I ordered a jig yesterday, hopefully it comes soon. I have a 1010 though, which I heard had more problems than others.
use a JIG
i made my custom JIG for 60 cents, save my Cappy after a failed cyanogen install.
I was running CM7 nightly builds. I was attempting to switch to the stable CM7 build with an ODIN restore. I couldn't get ODIN to recognize my phone, and a forum thread said to try re-installing the update.zip file from the recovery boot. It got hung up trying to do that and upon reboot, it is now stuck on the startup screen. Can't get to recovery, can't do anything. Any thoughts?
Help is GREATLY appreciated.
Thanks!
have you pulled battery and started again? tried button combos? have you used odin since installing cm7? i believe it needs different drivers..... more info will get you more help. more reading will keep you out of trouble (mostly) i've never used cm7 so i can't help that much...
I have tried pulling the battery, running the battery to dead and then putting it on the charger, all the button combos.
I have not tried ODIN but thats because ODIN needs to be in download mode and I cant get into download mode. The only thing I can get to is the AT&T World Phone screen with the white background. I have done some google searching about getting stuck on the boot screen but none of the threads I have found have seemed to mot relate to my exact problem. I am currently looking into if this is the kind of problem that a jig would fix.
definitely sounds like a job for a jig.. it will force it into d/l mode as long as the bootloaders are not corrupted..... best of luck
if the bootloaders are corrupted, is there anything to do or is the phone just finished?
Jtag/unbrickable mod
I had the same loop yesterday doing something else, but i had the ATT boot loop and no button combos worked to get into DL mode. So I tried pulling the battery, then holding vol+/vol-, putting battery back in, and then plugging in usb cable. Went to DL mode. If that doesn't work, I'm sure a jig would.
fuloplori said:
Jtag/unbrickable mod
Click to expand...
Click to collapse
Jtag should only be used for hard bricked phones. Since there is a sign of life, he can probably recover from this without the need of jtag.
Use a jig. It's the easiest way to get into dl mode. If you don't have one, you can make a crude one that will work until you can get a proper one ordered.
beast534 said:
I had the same loop yesterday doing something else, but i had the ATT boot loop and no button combos worked to get into DL mode. So I tried pulling the battery, then holding vol+/vol-, putting battery back in, and then plugging in usb cable. Went to DL mode. If that doesn't work, I'm sure a jig would.
Click to expand...
Click to collapse
That got it into download mode! I am going to try and ODIN restore and see what happens. Thanks!
ODIN Restore worked! I had to restart it a couple of times but I am back on stock. Now to get the stable CM7 becuase I don't think I can handle stock ROM again...
cdenney said:
ODIN Restore worked! I had to restart it a couple of times but I am back on stock. Now to get the stable CM7 becuase I don't think I can handle stock ROM again...
Click to expand...
Click to collapse
Great! Glad I could help
hey all, i've had my captivate for about two years now, and for a while i used cognition, then for the last year i've been using firefly. firefly has completely destroyed my phone's speed and responsiveness, and i needed to clean everything off and start with a minimalist ROM. so i picked slimICS.
i'm still very hazy on the details and terminology of flashing ROMs, but i got two to work (i remember using one-click root thing in 2010, and then in 2011 i flashed firefly through clockwork) so i figured it shouldn't be a problem to install slim, which i figured would be my last ROM until next year, when i'd get a new phone.
so i backed up my stuff, tried to get into recovery mode with the 3 buttons (didn't work, unsurprising since it didn't work last year either), took out my SIM, went to CWM, and selected the flash rom option. this restarted the phone and sent it into recovery mode--except it was the stock recovery, and i couldn't select anything because i think firefly made the phone think it was the i9000 model from canada, instead of the i897 captivate, so it assumed i had a physical "ok" button on my phone (which i obviously do not). i tried the power button, the various capacitive buttons on the bottom, nothing would select any of the options, so i just took out the battery and put it back in. the phone immediately booted into the CWM recovery menu, in which i selected flash ROM, and scrolled down to choose slimICS.
i let it do its thing for a while, it jumped between the AT&T white logo screen and a screen with scrolling text for like 5-10 minutes, then just stayed on the AT&T logo screen for another ten minutes. i should have left it for maybe a half hour to be sure, but i figured the install failed. i couldn't get out of this so i pulled the batttery. and now the phone is bricked (soft i hope). if i hold the power button it goes to the AT&T white logo, flashes briefly for a half-second and goes back to the screen, then stays there indefinitely. no button combinations seem to work. does anyone have any suggestions?
thanks!
Since you backed everything up, I'd suggest flashing a stock rom via Odin or Heimdall to clean everything up before moving forwards.
You can flash a non-bootloader one to be safe, or if you want to make sure you can flash anything, flash a package with Gingerbread bootloaders.
jmtheiss said:
Since you backed everything up, I'd suggest flashing a stock rom via Odin or Heimdall to clean everything up before moving forwards.
You can flash a non-bootloader one to be safe, or if you want to make sure you can flash anything, flash a package with Gingerbread bootloaders.
Click to expand...
Click to collapse
how do i flash anything in my phone's current condition? it doesn't turn on fully. it's stuck at the white AT&T logo.
Turn it completely off (pull the battery, if necessary), then hold V+ and V-, and insert a USB cable. That should put it in download mode. Once you're there, you can flash a stock rom (There's a stick with those roms in the development section).
jmtheiss said:
Turn it completely off (pull the battery, if necessary), then hold V+ and V-, and insert a USB cable. That should put it in download mode. Once you're there, you can flash a stock rom (There's a stick with those roms in the development section).
Click to expand...
Click to collapse
doesn't work. as i mentioned in the OP, i can't get into download or recovery mode or whatever. these button combos have never ever worked with this phone. for example, holding + and - and inserting a cable with ODIN open has never done anything. that's why i used clockwork.
Sounds like u r gonna need a Jig. If u are on a pc, click on my sig link below and there u will find a link on how to make a jig and/or where to buy one.
4-2ndtwin said:
Sounds like u r gonna need a Jig. If u are on a pc, click on my sig link below and there u will find a link on how to make a jig and/or where to buy one.
Click to expand...
Click to collapse
is that guaranteed to work? or is it most likely? or is it unlikely at this point?
The jigs that I have made myself in the past and as well the professional made ones that I have purchased have always worked to get me into download mode.
The jig is worth a try, I suggest you should
if I'm reading the op right, and if memory serves firefly was an I9000 build and button combos are different. My suggestion would get the Odin kk4 one click with repartition and WITH boot loaders from 4-2ndtwin's sig links, open that and while powered off and holding just the vol- button insert the USB that should do the trick. I9000 builds use different boot loaders with different button combos. Since you will be flashing a boot loader package be aware this is when you can truly hard brick your device. Be sure you have a good connection and cable before starting. If you still can't get into download mode I can +1 on the jig. The jig and 4-2ndtwins one click has saved my bacon more than once.
ok so i bought the jig, and good news: it gets me into download mode! yay!
problem: i don't know where to go from here. i've tried the following:
A. after getting into download mode, i followed the ODIN method here: http://forum.xda-developers.com/showthread.php?t=1350266, meaning i flashed the gingerbread bootloader update (nothing happened to the phone, which made me confused when i got to step 7., because i was STILL IN download mode), then flashed the speedmod kernel (which reset the phone, but it just got stuck in the "SAMSUNG CAPTIVATE i-897" white text on black screen, forever. i had to do a battery pull. turning on the phone goes to the same screen and then it freezes. trying to hold all three buttons to go into recovery mode alternates between that screen and the white AT&T screen, actually alternates, forever if i let it.
B. after that failed, i tried using the 2.2 Heimdall one-click (http://forum.xda-developers.com/showthread.php?t=1266172) but the file, when run, says
Code:
ERROR: Drivers Not Found
Installing drivers
but i still followed the instructions (except the instructions say "Install driver" but the actual button is "Replace driver"?) in any case, this does nothing. and then checking off "Flash bootloaders" and doing it again does nothing. the phone remains in download mode.
C. so i wanted to try one-click downloader http://forum.xda-developers.com/showthread.php?t=731989, but nothing pops up on the ODIN window when i plug my phone in. i can't even do anything.
please help!
please, does nobody know what to do?
Take a look at the "Captivate Connection Issues" thread for some more things to try. At this point, it sounds like you need to clear all the phone drivers off of your machine and reinstall them.
jmtheiss said:
Take a look at the "Captivate Connection Issues" thread for some more things to try. At this point, it sounds like you need to clear all the phone drivers off of your machine and reinstall them.
Click to expand...
Click to collapse
thanks, that worked! (it was my laptop that was the source of the connection issues i think; i tried all that stuff in the thread, but when i switched to the desktop, all of a sudden ODIN recognizes the phone!) i got my phone to flash ODIN one-click. so now i'm back to stock 2.1 eclair.
however, much to my dismay, i still can't get into recovery mode to (re-) root. the three button combo still does the weird flashing thing, where the white AT&T logo shows up, then the screen goes to black, then the AT&T logo, then black... ad infinitum. how do i either 1) enter recovery, or 2) re-root the phone + get a nice, lean, fast, modern ROM on it without going into recovery?
so far this thread has helped me unbrick the phone, now all i need is to update it from stock!
spacenegroes said:
thanks, that worked! (it was my laptop that was the source of the connection issues i think; i tried all that stuff in the thread, but when i switched to the desktop, all of a sudden ODIN recognizes the phone!) i got my phone to flash ODIN one-click. so now i'm back to stock 2.1 eclair.
however, much to my dismay, i still can't get into recovery mode to (re-) root. the three button combo still does the weird flashing thing, where the white AT&T logo shows up, then the screen goes to black, then the AT&T logo, then black... ad infinitum. how do i either 1) enter recovery, or 2) re-root the phone + get a nice, lean, fast, modern ROM on it without going into recovery?
so far this thread has helped me unbrick the phone, now all i need is to update it from stock!
Click to expand...
Click to collapse
I could be wrong but when you do the 3 button combo it sounds like you are continually holding the buttons which will cause it to keep looping like you describe. Starting with your phone off hold down all three buttons. The phone will show the white ATT screen. Then if you had a custom kernel it would show the kernel splash screen, in your case you said it just goes black which is fine too. Then you will of course get the white ATT screen again. As soon as you see the white ATT screen again release all the buttons and that should boot it into recovery.
m1batt1 said:
I could be wrong but when you do the 3 button combo it sounds like you are continually holding the buttons which will cause it to keep looping like you describe. Starting with your phone off hold down all three buttons. The phone will show the white ATT screen. Then if you had a custom kernel it would show the kernel splash screen, in your case you said it just goes black which is fine too. Then you will of course get the white ATT screen again. As soon as you see the white ATT screen again release all the buttons and that should boot it into recovery.
Click to expand...
Click to collapse
i tried various durations of holding the buttons. none worked. 2nd AT&T logo, nope. 1st black screen, nope. 1st AT&T logo, nope.
Your gonna have to get ADB set up on your pc. Then... "adb reboot recovery" will get u into recovery mode.
Sent from my SGH-I897 using xda premium