Related
There have been those that run into problems after installing the XXJP3I9000 update on the Samsung Captivate and attempt to reboot into recovery mode. The issue that they have is that since the Captivate has no physical home button to select an option like you can with the Galaxy S, you can't select an option, and therefore you can't reboot your device regularly. While I am in this same problem and have not figured out a solution, I have started this thread to post what knowledge I have about this issue so that others may help get this issue figured out. If anyone has information on how to fix this problem, please comment below. Let's fix this!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
First of all, the key combinations that standardly would work with the original captivate firmware will not work anymore. Pressing all three buttons (Vol+, Vol - and Power) will only power cycle the phone, that is, until you let up on the buttons. Pressing Vol+ and Vol- and then plugging your phone into the computer will also do nothing. (By nothing I mean will take you back to the recovery menu)
Every key combination will only take you back to the recovery menu, so key combinations seem to be out.
If you boot into recovery mode, take out the battery and put it back in, all the while keeping the phone plugged in to the computer, the phone will enter the "POWER RESET OR UNKNOWN UPLOAD MODE", which will show your device in windows as being a Samsung USB Composite Device and a Samsung Mobile Modem (gadget serial, Windows 7) While this may be helpful, you cannot run ODIN or ADB in this mode, nor does this allow disk access. If you have Samsung Kies installed, it will detect a device, but will never complete loading it.
Other information with this method: On the phone screen, as well as showing "POWER RESET OR UNKNOWN UPLOAD DEVICE" the screen will also show the following in red:
RST_STAT =0X1
PMIC_IRQ1 =0X0
PMIC_IRQ2 =0x0
PMIC_IRQ3 =0x4
PMIC_STATUS1 =0x40
PMIC_STATUS2 =0x2c
If this helps anybody, it was a pleasure
Another method I found briefly was that after installing Kies, and rebooting the phone into recovery mode (again) my computer detected four new devices, two of them being Samsung Android devices and one being a disk drive. Potentially, without freezing or error, the drivers that are included with the Kies software will detect and allow for disk management while the phone is in recovery mode. Three of the four devices installed without error for me, but the fourth, the actual Android device, continued to say "installing device" until I unplugged the phone out of frustration. It has since not detected those four devices again, and I have yet to figure out how to do that again. The nice thing about that was that although the adb.exe reboot download command did not work, adb.exe did detect the phone. if this is true then rebooting normally or into download mode should be easy.
The last thing I noticed is that button furthest to the left on the main screen on the captivate will close the recovery menu when pressed, and leave the background behind, and then will reopen the recovery menu when pressed again. This is showing me that the four touch buttons are operable, but not configured. If it were possible to reconfigure the actions that pressing these buttons do, then it would be easy to be able to reboot the device normally.
I have compiled information to the best of my ability, and here is a question to ask, that I think will help solve the problem. Can the captivate with I9000 2.2 software run adb in recovery mode?
Comments, Questions, and Most of all, answers would be appreciated for me, as well as for other users with the same problem as I. Hopefully, this thread can be the solving point for this problem.
Many Thanks,
TouchofDestiny
The n00b who isn't a n00b at all
An Update: The reason that the combinations don't work for me or either people is because they (and I) fail to install the captivate kernel, and that is making the volume power button controls useless.
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
You're problem is a little different. If you can't get into recovery mode, than that means you aren't in recovery mode, which means you can use ADB to enter download mode and use Odin to flash your phone. I have given up looking for a solution, and have sent my phone back to AT&T for a replacement. Since I'm still in my thirty day trial period, it doesn't matter if I used different firmware or not. Hopefully others won't get into the situation I had. For me, this thread is complete.
brandon9721 said:
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
Click to expand...
Click to collapse
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
yep, same boat
I am in the same position here. I downloaded the froyo leak and installed it with odin, no problem there. Upon startup into froyo, all was good, except my phone was stuck in horizontal mode until I tilted it vertical, *then* it would go horizontal. So basically I am 90 degrees off kilter. I decided to look around for another rom to try, and in the process managed to get stuck in recovery mode. Couldn't tell ya what firmware I have, just what is on the endless recovery screen that I cannot get out of!
I have no external microSD card, only the SIM card, and no way to get it recognized on my XP or win 7 system.
Really, really stuck here, guys. I do have the androidsdk installed, if there is a way to get it to reboot. As it is, adb cannot see the device, so I am looking at a truly bricked phone.
And yes, this is a US phone, which is why the power button and home button are not mapped (I assume).
I am DESPERATE for some help here!
and while I am at it...
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
pkrouse said:
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
Click to expand...
Click to collapse
when you are on the i9000 rom the only button that will get you in download mode is the vol down
That's HUGE!
You, sir, are a gentleman, scholar, and all-round smart guy! How did I miss that? I coulda SWORN I was getting into download mode with both volume keys. I've never been so happy to see a little Dalek dude with a shovel in my LIFE. 2 minutes in the one-click installer and now I'm back in business!
Thanks for helping a terrified owner out, and preventing a trip to the AT&T store.
I cannot go to download mode
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
xaga150 said:
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
Click to expand...
Click to collapse
the key to the i9000 rom/kernel button combo is VOL DOWN + using the USB trick. do not press vol up + down, just the down while you are plugging in the usb cable
i too am stuck in recovery mode. the only way i can get into download mode is by using both volume buttons. just holding the down button just sends me to revoery mode as well. how can i fix my phone in download mode?
nevermind, reinstalled 2.2 and it works now.
Eureka I got it...I think
I installed froyo 2.2 i9000 on my captivate and got stuck in recovery mode...power button doesnt select and when I hold down the up and down vol buttons I couldnt get the downloading icon anymore either. Then I remembered something from another post....
Home + Vol Down + Power = Downloading Icon
It worked for me....let me know if this helped....I'm officially unbricked.
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
JPBetley said:
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
Click to expand...
Click to collapse
JPBentley-- Since the I9000 firmware is set to use physical buttons, and the Captivate doesn't contain any, once you get into recovery mode, you cannot get out. The standard Captivate key combinations to get into download mode do not work, as do the combinations to get into download mode via the I9000 firmware. Basically, you get to a dead end. Unless there is some way to flash the phone's ROM outside of download mode, which I doubt, your best bet is to return the phone for a replacement. After haggling around with AT&T for a while, they admitted that installing the I9000 ROM doesn't invalidate your warranty, so they should take it back. They did with mine, and now I'm running the official Froyo leak. Good luck with your new phone!
SOLUTION
For all those that are having this problem, Ive struggled with it & tried EVERY possible button combination & nothing worked.
The ONLY solutions I have found is to use a usb JIG. Take out the battery, sim card & sd card, plug in the Usb JIG & put the batter back in. Give it a couple of seconds & I'tll enter recovery mode without pushing any buttons. You dont even need to push the power button, it's that simple.
Here is an image of how to make one if you are electronically inclined, personally I am not so I found a local electronic parts store & they put on together for me.
1.bp.blogspot.com/_3KjgtwnRiWM/TNTyjkZGquI/AAAAAAAABL4/7NSmqrYmkmU/s640/i900.jpg
If you want, you can also buy one online, I cant post a link becuase Im a new member but just search for "samsung usb jig" on ebay.com & youll find plenty.
shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=samsung+usb+jig&_sacat=See-All-Categories
yes, i think you need to build a jig or buy one online if you want to play with custom rom. you may not need it now, but you may need it just in case.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139
agustinpac said:
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
Click to expand...
Click to collapse
OMG you saved my life
thx so much for your post
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
drowe24 said:
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
Click to expand...
Click to collapse
That's not even close to a brick. Are you using a usb port closest to the motherboard on your pc? Is your cable good? Make or buy a jig, that will put your phone into download mode.
Sent from my blazing fast Captivate running Continuum GB ROM using Tapatalk Pro
Hi
first of all thank you for so much info.
I spend more than 10 hours looking for a solution on other posts but can't fins a solution.
my phone is bricked and i am not able to get to the download mode or the recovery. before I bricked it I was able to get the download mode with adb with since i tried odin, i have the phone --!-- computer
I am in canada so returning it would be a hassle. any help would be much appreciated to get to the download mode
thank you very much
Download Odin.
Take out the SIM, SD card, and battery. Launch Odin, replace the battery, and plug the USB cord in, and just press down on the volume up and down buttons.
This should boot it right into download mode, then flash with Odin.
This phone is virtually IMPOSSIBLE to brick.
man, i tried that maybe 50 times no kidding!
still no download mode
SeriousBizznass said:
Download Odin.
Take out the SIM, SD card, and battery. Launch Odin, replace the battery, and plug the USB cord in, and just press down on the volume up and down buttons.
This should boot it right into download mode, then flash with Odin.
This phone is virtually IMPOSSIBLE to brick.
Click to expand...
Click to collapse
Hold the volume buttons first then plug in the usb. Thats what works for me. You have to have odin open first like he said.
just tried and still nothing....
if somebody is located in montreal, i would love to meet them to check that out
Athailias said:
Hold the volume buttons first then plug in the usb. Thats what works for me. You have to have odin open first like he said.
Click to expand...
Click to collapse
Having Odin open makes no difference if his button combo is not working. Unfortunately some people are not aware that there phone does not have the 3 button combo working.
what is your solution when you don t have the 3 button combo working?
The only thing you can do if there is no way to reach download mode is to contact At&t or samsung and see if they can repair the phone for you.
Have you tried using a different usb cable, someone mentioned that some USB cables dont work right with the captivate, try the one that came with the phone.
I know odin doesnt matter, but if he is going to flash with odin it helps to have it open first is all I meant. As far as that screen and no three button combo I think you are done... bricked... sorry, dont take my word for it though.
I could enter download mode with key combination before applying Cog's Beta5.5...
I've returned my cappy for exchange.
I am trying with the cable that came with the phone. I don't have another one.
I just bought this phone out of ebay. I will give it this week end to try and find a solution.
I really don't see any as of now but we'll see...
I will try return the phone to the ebay seller as i asked him before buying it if you could go into download mode! and he said yes!
man, I hope i find a solution!
what happens when you try and start your phone normally -- boot screen loop, anything?
Can you get into recovery mode?
when I try to start it normal I get the phone--!--computer
I am sure I tried recovery mode without any success. I am telling I spent so much time on this forum that my wife is going to start being jalous
How do you get to recovry mode again? I tried so many things, that I don't remember
you can't get the phone to be recognized on your computer? Could do ADB to boot into download.
But the battery trick should work.
Pull the sim, external sdcard, and battery.
Hold down the volume buttons and plug in the USB
Then jam the battery back in.
It might take a few times to get it.. but it should get into download mode. I just restored mine doing this trick when it was stuck on this screen.
Really we need to have a youtube vid of this technique
younescito said:
when I try to start it normal I get the phone--!--computer
I am sure I tried recovery mode without any success. I am telling I spent so much time on this forum that my wife is going to start being jalous
How do you get to recovry mode again? I tried so many things, that I don't remember
Click to expand...
Click to collapse
Hold down both volume buttons then hold down the power button until the boot s screen flashes two times then release the power button.
BTW - although it is a LOOOOONG video.. this might help folks out:
http://www.youtube.com/watch?v=iefapF1yZhE&feature=related
Not sure if it will help, but I've also read that you should use the actual motherboard usb ports and not a hub or any kind of "external" ports (i.e. the ports on the front of the tower)
i did all that stuff.
I ended up returning it to the ebay seller who will send me another captivate.
thanks guys
My download was working on cog 2.2 beta before i flashed back to stock using odin. Now when I try to enter download mode i just see the charging symbol. So the only thing that has changed is software. Could odin3 remove my download mode? What can i do?
Its been a rough night for me. I did a Nandroid backup which turned out I needed to restore after something else failed. After restore I did not have what I expected.
Anyway, to make a long story short, I ended up in a situation that no matter what I did, I could not get into download mode. Only recovery.
The good news is that after trying several different things, I finally found I had the original base rom I was using still on the SD card (even though I had done a Master Clear). I guess maybe the only thing that will empty the SD card is to format it.
I have no idea what I would have done had I not had a Clockwork zip on there.
I installed Amimod that lets me change the transitions between apps, i ran it to change it to a cross fading transition and it said i had to reboot later to make the changes take effect. I kept that and mind and used some other apps. They all didn't load and gave me the "com.xxx.xxxx is unable to continue" type deal with the force quit button.
So i restarted my phone and now launcher loads but the pop ups come saying "com.android.phone is unable etc" or "com.android.media is unable...". There is no status bar and the phone doesn't lock. After about five minutes of trying to press the force quit button, nothing happens. I went into recover mode and cleared my cache but that didn't help.
[tldr] I can get my phone into download mode but is it possible to open the phone as a root folder on my computer so i could uninstall Animod and any changes it made? I don't want to master reset.
ROM reflash is only option.
I reflashed using odin but now its stuck in a boot loop with the att logo. When i plug it into the usb it loops the loading sign and the battery sign. What now?
Have you used odin before?
Which odin did you use?
What build is your phone?
Can you still get into download mode?
I have not used odin before this was my first time.
I used the one that is prepackaged with the .pit and .tar file "I897UCJF6-final-OCD-REV0.exe"
My phone was stock android that i rooted.
Cant get it into download with any button combo.
Under your battery left side on the white sticker. Your phone had a build number. Mine is 1008. 10 meaning 2010 08 meaning august. What is yours
Also tell me exactly what you have tried to get into dl mode
Build number 1011, and now my phone wont even turn on. When i hold the power button it is unresponsive, and its not dead i charged it.
Niwatori said:
Build number 1011, and now my phone wont even turn on. When i hold the power button it is unresponsive, and its not dead i charged it.
Click to expand...
Click to collapse
Looks like you will need to try to force the DL mode with the odin instructions or get a jig and see if that works
Download mode
remove all sd, sim, bat
Put bat back in
Hold volume up abd down
Plug in usb
In it works great, if not usb jig
Going forward do not use odin one click use this method
http://forum.xda-developers.com/showpost.php?p=10056254&po
i got it into download mode using the button combos (battery out then hold vol up and down etc) and used the odin 1 click downloader for captivate, but it failed twice.
It got to the point where I had to buy some resistors to make a USB jig. The jig worked fine and put it into download mode but Odin still failed...Twice more. Now my phone wont even show the logo when i hold the powerbutton and the jig doesnt seem to work anymore. Its not the battery because i charged it for a full night before i tried jigging it again.
I would try the non one click odin method now except that i cannot get my phone into download mode.
I have no idea what to do now, it seems like its completely bricked.
At this point (if I'm able to replace it) would the workers at samsung or att be able to access my data at all? I only had the phone for 3 months. And would my warranty be void for rooting/flashing?
Niwatori said:
At this point (if I'm able to replace it) would the workers at samsung or att be able to access my data at all? I only had the phone for 3 months. And would my warranty be void for rooting/flashing?
Click to expand...
Click to collapse
Hypothetically, yes and yes, but the reality is they will likely just wipe it and reflash it without ever looking at what's on it. Just tell them something went wrong when you tried to upgrade to Froyo via Kies. That's happened to enough people that they probably won't question it.
I had Cognition 4 flashed but had a problem that whenever the battery was removed when the phone was on, about half of my apps, wifi, and texting would force close on reboot and never be able to open until I reflashed Cogntion. Because of this, I decided to try Serendipity VII. I put the zip file on my phone, rebooted into recovery, then tried to do the same thing that I did for Cognition. When I did this it said that it was installing, then said install complete without rebooting. I decided to reboot the phone, and when I tried, it keeps looping on the att screen. I do not see the battery charge signal when I plug it in. I see a loading gear for the battery for about five seconds, then the screen has electric looking blue lines flash through the center and then nothing. I cannot boot into recovery or download, it just keeps looping on the ATT screen.
Make or buy a jig to force it into download mode.
Sent from 234 Elm Street
slow_DC4 said:
Make or buy a jig to force it into download mode.
Sent from 234 Elm Street
Click to expand...
Click to collapse
How do I force it into download mode?
So you tried flashing a GB rom without first flashing GB bootloaders?
You should have read and followed the installation instructions on the Serendipity download page. Start Odin one click,see if you can get phone into download mode by any combo and see if Odin sees it. Flash stock and start again.
*If you're not on Gingerbread, you should be shot*
cappysw10 said:
So you tried flashing a GB rom without first flashing GB bootloaders?
You should have read and followed the installation instructions on the Serendipity download page. Start Odin one click,see if you can get phone into download mode by any combo and see if Odin sees it. Flash stock and start again.
*If you're not on Gingerbread, you should be shot*
Click to expand...
Click to collapse
Ya, I had a feeling I should have read more about it, but I was anxious and stupid. I didn't do any of those things. No matter what I try I can't get to recovery. How would I get into download?
JIG
10 char
Thanks for all the help, I will be buying a jig from amazon for about ten bucks. I hope this works. But if it doesn't, at least this will teach me to read instructions before doing something that I don't understand very well.
to get into download mode press volume down instead of volume up to get u into recovery, at first i screwed up too somewhat like you so what i did is removed the battery for a minute, put it back in press volume down middle and power button to get into download then use odin to flash a new 2.3.4 gingerbread that u can get from this forum just look through and ull find it, make sure u put the pit file phone file, pda and csc files and make sure u check the repartition auto reboot and freset time checked on then press start hope it helped
srkoza said:
to get into download mode press volume down instead of volume up to get u into recovery, at first i screwed up too somewhat like you so what i did is removed the battery for a minute, put it back in press volume down middle and power button to get into download then use odin to flash a new 2.3.4 gingerbread that u can get from this forum just look through and ull find it, make sure u put the pit file phone file, pda and csc files and make sure u check the repartition auto reboot and freset time checked on then press start hope it helped
Click to expand...
Click to collapse
Ya, holding the volume button in any combination does noting, I hope a jig will fix it. But thanks anyway
jmj45 said:
Ya, holding the volume button in any combination does noting, I hope a jig will fix it. But thanks anyway
Click to expand...
Click to collapse
Sir try this one last thing, remove your USB Cable from your PC, remove your battery...
While holding down both (Up and Down) volume buttons, insert the battery and THEN connect your phone to your PC through USB, see if this puts it into Download mode.
If not, try doing the same just holding down the DOWN volume button. Hope this helps, it seems as if these combinations kind of vary from phone to phone. Cheers
Mr. Janderson said:
Sir try this one last thing, remove your USB Cable from your PC, remove your battery...
While holding down both (Up and Down) volume buttons, insert the battery and THEN connect your phone to your PC through USB, see if this puts it into Download mode.
If not, try doing the same just holding down the DOWN volume button. Hope this helps, it seems as if these combinations kind of vary from phone to phone. Cheers
Click to expand...
Click to collapse
I tried this and all it did was do the att loop screen thing. Also, my computer dinged that it saw a usb device being plugged in, but then the restart loop restarts the phone and continues this indefinitely. Thanks for the help anyway.
You don't need to buy a jig, just go do that thing where you get three (or four) resistors in series that totals 301k ohms and touch them to specific contacts in the usb port of your phone... look it up on xda, it's worked for most people.
abmicyau said:
You don't need to buy a jig, just go do that thing where you get three (or four) resistors in series that totals 301k ohms and touch them to specific contacts in the usb port of your phone... look it up on xda, it's worked for most people.
Click to expand...
Click to collapse
Thanks, but I already screwed up my phone by doing something that I did not fully understand, it's a small wonder that I can use Linux and not be too confused. I think I will take the easy way out with this one.
Hmm I remember that often when I tried to put my phone into recovery mode or download, whenever I held the Power Button down, it would just keep looping. When you but the battery on and connect your phone, make sure you are not holding the Power button, just the volume ones. Perhaps it is your case?
Mr. Janderson said:
Hmm I remember that often when I tried to put my phone into recovery mode or download, whenever I held the Power Button down, it would just keep looping. When you but the battery on and connect your phone, make sure you are not holding the Power button, just the volume ones. Perhaps it is your case?
Click to expand...
Click to collapse
It loops if whether or not I hold any buttons down. If I hold the power button down while trying to get into download mode, then it just turns it off.
Turn off the phone, remove the battery, get a stock odin one click for the captivate.
I897UCJF6-final-OCD-REV0 seems to be a reliable flash when I run into trouble.
Start odin, plug the phone into the USB cable, hold the volume up/down key or try any combination up/down or both. Insert the battery and hopefully it will go into download mode.
Been reliable so far...
Hi. I'm unable to get into recovery mode after I flashed the Talon kernel as per the instructions here.
http://www.team-continuum.net/forum...ses/(guide)general-installation-instructions/
I'm consistently able to get into download mode and reflashed the talon 0.1.2 kernel as per the instructions there, but still to no avail. Any other suggestions to get my phone into CWM ?
Im trying to flash Continuum 6
Might as well get the Jig easy Download mode xD. I made mine myself cost a whole $2.50 for one xD
Hello,
I just bought for my mother a galaxy mini. Now i root the phone with superoneclick. i downloaded rom manager and clicked on the first option flash clockwork mod, there was a popup and i clicked the first one accidentatily and after a few seconds he said he was finished.. i turned of the phone and know he deosn't do anything at all no recovery, no download mode please help me fix the phone!
----
Edit
I just discovered that when i have plugged in the phone to the computer, and i press the buttons for recovery mode then the computer recognize my phone. Can i do anything now to make my phone work again, it seems like my display doesn't turn on by a wrong rom installed
bricked. (not very sure,cwm frm rom manager is partially supported now. work in progress)
only if ur able to get into download mode u'll be able to flash a rom...
http://androidforums.com/samsung-ga...-unbrick-mini-s5570-bricked-black-screen.html
That is a nice, nasty, hard brick.
If you are getting into download mode and ODIN running on the PC recognises your phone, you are lucky - get any stock rom from samfirmware and flash it first. Use the phone for a few days more, and then, you can upgrade to new 7.1 cyanogenmod ROM.
try going into download mode by holding home and vol down the connect the usb 2 ur phone
or try holding vol up+down home and power
if it doesnt work try getting a jig from ebay
get a jig its the only way to fix it
SSC (Samsung Service Center) is the only way.
Congrats, next time read before doing anything.