There have been those that run into problems after installing the XXJP3I9000 update on the Samsung Captivate and attempt to reboot into recovery mode. The issue that they have is that since the Captivate has no physical home button to select an option like you can with the Galaxy S, you can't select an option, and therefore you can't reboot your device regularly. While I am in this same problem and have not figured out a solution, I have started this thread to post what knowledge I have about this issue so that others may help get this issue figured out. If anyone has information on how to fix this problem, please comment below. Let's fix this!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
First of all, the key combinations that standardly would work with the original captivate firmware will not work anymore. Pressing all three buttons (Vol+, Vol - and Power) will only power cycle the phone, that is, until you let up on the buttons. Pressing Vol+ and Vol- and then plugging your phone into the computer will also do nothing. (By nothing I mean will take you back to the recovery menu)
Every key combination will only take you back to the recovery menu, so key combinations seem to be out.
If you boot into recovery mode, take out the battery and put it back in, all the while keeping the phone plugged in to the computer, the phone will enter the "POWER RESET OR UNKNOWN UPLOAD MODE", which will show your device in windows as being a Samsung USB Composite Device and a Samsung Mobile Modem (gadget serial, Windows 7) While this may be helpful, you cannot run ODIN or ADB in this mode, nor does this allow disk access. If you have Samsung Kies installed, it will detect a device, but will never complete loading it.
Other information with this method: On the phone screen, as well as showing "POWER RESET OR UNKNOWN UPLOAD DEVICE" the screen will also show the following in red:
RST_STAT =0X1
PMIC_IRQ1 =0X0
PMIC_IRQ2 =0x0
PMIC_IRQ3 =0x4
PMIC_STATUS1 =0x40
PMIC_STATUS2 =0x2c
If this helps anybody, it was a pleasure
Another method I found briefly was that after installing Kies, and rebooting the phone into recovery mode (again) my computer detected four new devices, two of them being Samsung Android devices and one being a disk drive. Potentially, without freezing or error, the drivers that are included with the Kies software will detect and allow for disk management while the phone is in recovery mode. Three of the four devices installed without error for me, but the fourth, the actual Android device, continued to say "installing device" until I unplugged the phone out of frustration. It has since not detected those four devices again, and I have yet to figure out how to do that again. The nice thing about that was that although the adb.exe reboot download command did not work, adb.exe did detect the phone. if this is true then rebooting normally or into download mode should be easy.
The last thing I noticed is that button furthest to the left on the main screen on the captivate will close the recovery menu when pressed, and leave the background behind, and then will reopen the recovery menu when pressed again. This is showing me that the four touch buttons are operable, but not configured. If it were possible to reconfigure the actions that pressing these buttons do, then it would be easy to be able to reboot the device normally.
I have compiled information to the best of my ability, and here is a question to ask, that I think will help solve the problem. Can the captivate with I9000 2.2 software run adb in recovery mode?
Comments, Questions, and Most of all, answers would be appreciated for me, as well as for other users with the same problem as I. Hopefully, this thread can be the solving point for this problem.
Many Thanks,
TouchofDestiny
The n00b who isn't a n00b at all
An Update: The reason that the combinations don't work for me or either people is because they (and I) fail to install the captivate kernel, and that is making the volume power button controls useless.
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
You're problem is a little different. If you can't get into recovery mode, than that means you aren't in recovery mode, which means you can use ADB to enter download mode and use Odin to flash your phone. I have given up looking for a solution, and have sent my phone back to AT&T for a replacement. Since I'm still in my thirty day trial period, it doesn't matter if I used different firmware or not. Hopefully others won't get into the situation I had. For me, this thread is complete.
brandon9721 said:
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
Click to expand...
Click to collapse
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
yep, same boat
I am in the same position here. I downloaded the froyo leak and installed it with odin, no problem there. Upon startup into froyo, all was good, except my phone was stuck in horizontal mode until I tilted it vertical, *then* it would go horizontal. So basically I am 90 degrees off kilter. I decided to look around for another rom to try, and in the process managed to get stuck in recovery mode. Couldn't tell ya what firmware I have, just what is on the endless recovery screen that I cannot get out of!
I have no external microSD card, only the SIM card, and no way to get it recognized on my XP or win 7 system.
Really, really stuck here, guys. I do have the androidsdk installed, if there is a way to get it to reboot. As it is, adb cannot see the device, so I am looking at a truly bricked phone.
And yes, this is a US phone, which is why the power button and home button are not mapped (I assume).
I am DESPERATE for some help here!
and while I am at it...
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
pkrouse said:
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
Click to expand...
Click to collapse
when you are on the i9000 rom the only button that will get you in download mode is the vol down
That's HUGE!
You, sir, are a gentleman, scholar, and all-round smart guy! How did I miss that? I coulda SWORN I was getting into download mode with both volume keys. I've never been so happy to see a little Dalek dude with a shovel in my LIFE. 2 minutes in the one-click installer and now I'm back in business!
Thanks for helping a terrified owner out, and preventing a trip to the AT&T store.
I cannot go to download mode
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
xaga150 said:
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
Click to expand...
Click to collapse
the key to the i9000 rom/kernel button combo is VOL DOWN + using the USB trick. do not press vol up + down, just the down while you are plugging in the usb cable
i too am stuck in recovery mode. the only way i can get into download mode is by using both volume buttons. just holding the down button just sends me to revoery mode as well. how can i fix my phone in download mode?
nevermind, reinstalled 2.2 and it works now.
Eureka I got it...I think
I installed froyo 2.2 i9000 on my captivate and got stuck in recovery mode...power button doesnt select and when I hold down the up and down vol buttons I couldnt get the downloading icon anymore either. Then I remembered something from another post....
Home + Vol Down + Power = Downloading Icon
It worked for me....let me know if this helped....I'm officially unbricked.
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
JPBetley said:
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
Click to expand...
Click to collapse
JPBentley-- Since the I9000 firmware is set to use physical buttons, and the Captivate doesn't contain any, once you get into recovery mode, you cannot get out. The standard Captivate key combinations to get into download mode do not work, as do the combinations to get into download mode via the I9000 firmware. Basically, you get to a dead end. Unless there is some way to flash the phone's ROM outside of download mode, which I doubt, your best bet is to return the phone for a replacement. After haggling around with AT&T for a while, they admitted that installing the I9000 ROM doesn't invalidate your warranty, so they should take it back. They did with mine, and now I'm running the official Froyo leak. Good luck with your new phone!
SOLUTION
For all those that are having this problem, Ive struggled with it & tried EVERY possible button combination & nothing worked.
The ONLY solutions I have found is to use a usb JIG. Take out the battery, sim card & sd card, plug in the Usb JIG & put the batter back in. Give it a couple of seconds & I'tll enter recovery mode without pushing any buttons. You dont even need to push the power button, it's that simple.
Here is an image of how to make one if you are electronically inclined, personally I am not so I found a local electronic parts store & they put on together for me.
1.bp.blogspot.com/_3KjgtwnRiWM/TNTyjkZGquI/AAAAAAAABL4/7NSmqrYmkmU/s640/i900.jpg
If you want, you can also buy one online, I cant post a link becuase Im a new member but just search for "samsung usb jig" on ebay.com & youll find plenty.
shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=samsung+usb+jig&_sacat=See-All-Categories
yes, i think you need to build a jig or buy one online if you want to play with custom rom. you may not need it now, but you may need it just in case.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139
agustinpac said:
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
Click to expand...
Click to collapse
OMG you saved my life
thx so much for your post
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
drowe24 said:
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
Click to expand...
Click to collapse
That's not even close to a brick. Are you using a usb port closest to the motherboard on your pc? Is your cable good? Make or buy a jig, that will put your phone into download mode.
Sent from my blazing fast Captivate running Continuum GB ROM using Tapatalk Pro
Hey guys,
I searched everywhere, and could not find an answer. Heres what happened:
Messed up Cyanogen install, so I used a One Click installer to go back to stock.
Once stock, popped phone in download mode, and used Odin to flash the CM7 kernel. Odin said PASS
Unplugged USB and held both volume rockers and the power button.
Phone rebooted (i let go at the ATT screen), and it now sticks at the Galaxy S / cyanogen(mod) screen.
I have tried these methods (for both download and recovery mode)
Held both rockers and plugged in USB (the battery just came up)
Put battery in, held one rocker at a time and power
Tried ADB, but it can't find the device.
Also tried holding all three buttons (both volume rockers and power) and the phone did the same thing.
Odin won't pick it up, ADB won't pick it up, and it seems that I can't get into Download or Recovery mode.
Any ideas? Just I just buy a Jig to go into download mode?
Had that happen to me when I tried to ditch cm7 and go back to stock so I could flash serendipity. I lost my 3 button combo flashing cm7 for some reason.. worked fine before cm7 for both recovery and download mode, and neither worked after flashing cm7.
Solution is to just use a jig to go back to stock and flash a new rom from there. Or you can do what I did and use a jig to go back to stock, then flash cog 4.2 or something that includes an sbl with the 3 button fix.
Hi ..
The same thing happened on my phone yesterday i was trying to install the MIUI rom on my phone.
The phone is stuck on the Galaxy S Cyanogen Mod Screen .
ADB doesn't detect my phone.
I never had the 3 button combo working on my Captivate for AT&T.
I used the adb commands to enter recovery and download mode..
Now Since the phone itself is not getting detected i can't even use adb commands.
What do i Do next.??
Please help..
would really appreciate suggestions...
thnks...
Get a jig, saved my phone a few weeks ago after a bad rom install.
I am hoping someone can help me out. Yesterday I was using Odin to flash Apex 10. I was loading the bootloaders when the usb cable was pulled out and I didnt have the battery cover on and the battery fell out. Now I cant get into download mode. I have pulled the battery a thousand times. Before this happened I was able to use the three buttons to get into download mode. I need to start the process all over but cant do anything without getting into download mode. I dont have a jig. I searched and saw where I could download the three button fix. When I use CWM and reboot to recovery it doesnt give me the option to install from SD card.
The phone works but when I turn it on the booting animation says Galaxy i9000. Im currently on 2.2...baseband I897UCKB2.
Can I use AIO toolbox to correct this problem? After messing up last night I'm a little nervous at this point.
Also could someone point me to the correct bootloader for the Captivate? I want to make sure I used the right one.
Thanks in advance and please dont flame me. I searched this forum and honestly what I found only confused me more.
^
Do not use the 3 button fix or u may hard brick ur phone.
The i897 gingerbread bootloaders link is in my signature below.
Right click and run as administrator the Odin 1st. Then...
To get in download mode try leaving out ur battery, connect usb end of cable to usb port in the back of desktop computer or 1st port on laptop, connect micro usb end to phone while holding volume down button only , replace battery and cover, Odin may recognize your phone now, if so flash the i897 booloaders. Set phone aside and wait, should not take long.
If you get the "phone ! computer firmware upgrade fail" screen, don't worry, just treat it as a download screen. If all this does not work, then u will need to make or buy a jig.
Do not flash the 3 button fix over this you will hard brick your phone
If u can boot your phone after all this thn you are one lucky guy, You messed while flashing th BL and your phone still works, If you have i9000 boot screen that means you have flashed the i9000 bootloaders.
After flashing the i9000 BL the combination for the DL and recovery chages to.
Volume down plus power= DL
Volume up plus power = Recovery
.
I swear I love both of you. I got the phone in download mode by volume dwn + power. I will see if I can accomplish what I set out to do last night.
Apologies if this has been answered a hundred times but I upgraded the wife's Galaxy S to ICS but it lagged too much. The Kernel that was on it wouldnt let me flash Darky again through recovery so I tried to put stock back on via Odin and this happened.
I dont know the terminology so apologies if this is an issue with a name that I don't know, hence the picture.
Is there a way back from this?
Happened to me also when i unpluged while executing pit file.. Just if you still able to go to download mode, try flash with odin again. Worked for me. If you get any problems reply then
Sent from my GT-I9000, yeah Galaxy S one
Buy a USB jig off Amazon for a few dollars. It'll take you into Download Mode if you can't.
Before buying a JIG, try this:
1. remove battery
2. connect phone with computer via usb (without battery)
3. then press 3-button combo for download mode
4. while pressing these 3 buttons (phone is still connected to pc) put back your battery (for example using your nose )
Worked for me already a few times! If it won't work for the first time, try again and again..
Ajoslaf said:
Before buying a JIG, try this:
1. remove battery
2. connect phone with computer via usb (without battery)
3. then press 3-button combo for download mode
4. while pressing these 3 buttons (phone is still connected to pc) put back your battery (for example using your nose )
Worked for me already a few times! If it won't work for the first time, try again and again..
Click to expand...
Click to collapse
You my friend are a god damn legend! Im in DL mode
Hi there, i want to ask some help to you. This is very sucks for me, when i need to communicate with my family and my friends, my phone was had a probelm. First probelm is my phone was bootloop, it was booted just until "Samsung Galaxy S III Mini" logo. Second probelm, after that bootloop, my phone was restarted and go back again to boot logo, and then restart again and go back again to boot logo, again and again continuosly until my battery was drain down. And the last probelm, after i found that probelm then i try to flash my phone to newest version firmware, when my phone enter to download mode and try to connected to my PC, it not recognized with my PC, indeed there's no notification that the device is not recognized (normally if you connect the device to PC and not recognized, will show notification "USB Not Recognized"). I try to connect again on Windows 7 (My PC was dual-booted Windows 10 and Windows 7), there's no changed, still not recognize and not showing notification. And then, an hour ago before i posted this post, i try to connect and flashing in my friends PC, but still not recognized. I think there's no probelm with my USB cable, when i use to charging, it still working.
And then i really really really need your solution, PLEASE help me, i dont have much money to repair my phone because i just have IDR 10000 (converted to USD is just $0,95) and my guarantee is expired. Soon i will face the National Exam and i dont want lost my focus to that. I hope i can get the best solution quickly. Thanks for your attention, sorry for my badly english. :crying::crying:
Hi
I had similar problem my solution was to download samsung mobile drivers for s3 mini.
Follow these steps
Download Drivers
Install Driver
Download and Install Odin 3.07
Download Original firmware it is on xda. Msg me and I send you link
Open ODIN select firmware in PDA
Turn Off Phone. Take Battery out
Hold Power Button and Down I think to get to download mode
Connect cable
Continue download mode
In odin it should show up com connected
In odin press start
Let it flash rom dont desconnect cable even when it finished.
Once completed turn on fone with cable inserted to pc until phone completely starts up to main menu
Msg me if you hv problem.
just a little side note....where did u get windows 10.......good luck with the phone
Hi whith model s3mimi you have i8190x or 8200? If 8190 do that:
1.Download drivers and Odin from novafusion.pl/downloads, there is section s3mini->extras and heres Drivers and Odin.
Download stock rom from sammobile or samsung-firmware for your specific model and location.
2.Install drivers, next unzip to any location Odin and downloaded rom, but in the same place both.
3.Take out battery and put in the phone, then push Vol- Home Power buttons until you see Download mode, then clik Vol+ to enter it.
4.Open Odin and select PDA and find unpacked stock rom then connect phone to usb. Make sure that ONLY Auto Reboot*and*F.Reset Time are selected.
Your pc find drivers and Odin show to you in first box in left corner info about port:comX, nevermind what number of Com but you must see info about Com port. Its important.
5.Pull button Start and wait few minutes. On finish your phone restart, you dont need to disconnect from pc. Now wait 5-8min, in this time you see only logo samsung and thats all. After logo you see configuration panel and voila.
If not see configuration screen after 8min, pull out batt, put in, go to recovery by Vol+ Home Power Buttons and clean cache, next do factory reset. Now might be work, but after restart you still wait max 8min until see configuration screen.
Sent from my GT-I8190 using XDA Free mobile app