Database Develop

HELP: I accidently installed a Sam. CAPTIVATE rom on a Galaxy S i9000- Not booting up

PLEASE HELP: Calling all experts!!!
After installing the: [STOCK ROM] Odin3 One-Click Downloader and Drivers CAPTIVATE ONLY
My Galaxy S 19000 is stuck on the at&t boot screen.. the at&t logo just keeps flashing...
I cannot get into download mode...
PC is not recognising phone via Kies, odin or anything else...
Something tells me I have made a huge mistake somewhere along the line.. any fix???
Thank you

If no recovery/download mode working...
Only UART/JTAG, check on progress on this.

Thank you for your help...
Quite expensive options aren't these, GOOD THING I HAVE INSURANCE!!!
There must be a software way around this thou...
HELP!!!!

If your phone can't get into download mode due to it being disabled it looks like your pretty much screwed. You could phone samsung and see if they'd fix it.
Sent from my GT-I9000 using XDA App

If you can get to the AT&T logo part, I'm assuming you should still be able to get to download mode. Did your phone have dl mode before?

Thread moved to Q&A section

Yes my phone could get into dl mode b4 but now it doesn't work any more, phone just keeps on showing at&t logo and rebooting.
When I put the USB lead in the phone does not switch on at all..
thanks 2 all for assistance in this horrible mess negligence has left me in.

the USA models goes into download mode by using the volume up + volume down + power
see if that works

Thanks for your reply...
no joy... any other viable button combinations I could try? I've already tried many to no avail...

I'm no expert on the matter but don't you think that since you flashed a Captivate ROM on an I9000 that the home button wouldn't work since the Captivate doesn't share the same home button? Logically I would try looking for what the combo is for the Captivate to get into download or recovery mode. Now, I may be wrong and it may not work if the captivate uses its home button to enter the home button but it's worth a shot.
Edit: I just checked here and it says you hold both the volume up and volume down button while you press the power button. Try that.

With the device off, try holding both vol + & - then plugging in usb cable. Thats how a captivate enters download mode. If flashing the i9000 on captivate changes the button sequence it could not hurt to try.
Sent from my SAMSUNG-SGH-I897 using XDA App

@ Bell & foom....
I understand both your thought pattern and YES this was mine also...
However thus far no combinations have worked, still continually looping the at&t logo.
If I plug in the charger or USB whilst its doing this it kills the device, it wont switch on...
Knowing the different CAPTIVATE button comb. to recovery or download mode would be a big help right now.. also how the buttons would be mapped... i.e Captivate rom. on GALAXY S device?
How would one fix a captivate that was continually re-booting at operator logo start-up? Might be another way to angle this?
Thanks....

Think u are better off paying the guys at samsung or phone repair store to load the right firmware back in if u dont have the 3 btn combo...
Sent from my GT-I9000 using XDA App

try downloading that one click unroot program, plug the sgs into the computer and then force unroot, although the unroot won't work it should then allow the sgs to enter recovery mode.

Unfortunately my PC is not recognising the phone...
Plugging the USB in while the phone is switched OFF does nothing....
lugging the USB in while the phone is switched ON.. Turns it off...
Same things happen when the Charger is plugged in.. Althou the phone seems to still charge!!!
Arghhh..
Thanks for your suggestion thou.. Any more help/ ideas are welcomed...

Last resort maybe try heating up the phone like the others did to force download mode?
Sent from my GT-I9000 using XDA App

so any news on this? i too have successfully flashed the captivate rom on my unbranded i9000 the official repair shop i first took it to (mttc <Lithuania>) told me that it needs a new motherboard, and it would cost me 700LTL(270 $us)... kinda sounded like bull****, so a week ago i took it to a private repair shop, they said they had jtag, so i should be hearing from them this week, if not, i'll buy the stupid riff box myself and repair it..
no button combination worked for me, and the symptoms were exactly the same, flashing att, usb kills it etc. etc.
well, my advice would be to keep contacting different local repair shops, and asking do they have a jtag that supports the samsung galaxy s, if they do, the repair shouldn't cost more than 25$, at least thats what I've been told. good luck, and stay in touch, update on your process, cause the number of people flashing the wrong rom on the i9000 is horrifying.
it kinda sux that its so easy to brick the sgs... and its wrong for people to state that "if you have 3button combo enabled, you are safe", well thats just bull****.

No GOOD news as of yet, but I am in the process of to admitting my SGS to a official samsung service centre.. I was also thinking of sending it directly to them for repair...
???
Still been trying some other things to try and jump-start this blasted thing in the meantime but NOTHING IS WORKING!!!!
I to am thinking about purchasing this riff box or JTAG but it would be for a ONE TIME USE only... Seems like a waste of money when I can just claim a new SGS through insurance only thing is playing the WAITING GAME!!!
I Shall definitely update this thread with any progress made in the coming days...
Here I was thinking I was a lone soldier with this dilemma...
Also I agree... SGS = Too easily bricked.. and no solution?? Other than splashing out 100+ £/$... in your words truly SUXXXXXXX!!!!

Konshens said:
Also I agree... SGS = Too easily bricked.. and no solution??
Click to expand...
Click to collapse
Sorry, but ANY phone (or even any electronic component for that matter) is easily bricked if you flash firmware from a completely different device onto it.

Electroz said:
Sorry, but ANY phone (or even any electronic component for that matter) is easily bricked if you flash firmware from a completely different device onto it.
Click to expand...
Click to collapse
well, afaik, its very hard to fully brick a new htc device.
anyway, i suggest you try finding a jtag repair shop first, as samsung will take a lot of time to "repair" it, or even tell you that it needs a new motherboard..

[Q] In a LOT of trouble!

So a few days back i flashed the serendipity VII rom on to my previouly 2.2 Cappy, and it worked like a charm... a day later i was experimenting with a few ROMS all 2.3, and they worked, and to my luck I flashed a 2.2 ROM (Cognition 4) (by mistake i might add) and there it was a complete black screen brick!
since then Iv tried various methods to bring it back to life, the 3button thing, the taking the battery out holding down the 3 buttons connecting the usb and putting the battery back in, then releasing power only... Iv tried to even get it JTAGed, which was a disaster since the JTAG guy tried and cudnt get the thing to show connectivity... ANY HELP??
I fail to accept that this is the end... Please HELPP!!!!!

just keep trying to get into dl mode by using other usb ports, a jig, holding buttons while battery removed and install battery then plug in phone, happened to me plenty of times but was persistant that it finally got into dl mode.

Try making a jig and putting phone in download mode then flash stock through odin -- do a search for jig in the captivate forums. It saved me many times. You can even make one for about $1.

If you had gingerbread then you may need to use the i9000 version of entering download mode. The key combination is different. Search around on the forum as plenty have already mentioned what it is. I just don't remember off the top of my head.

if it will not power on at all....it doesnt look good.

try holding volume down and power...see if that brings up download mode. a jig is only $8 shipped to your home and will work.
i had a similar scenario and a jig brought my cappy back to life!! ive had the same phone since september, the jig has saved me from at least 8 new phones

I have seen a black screen for download mode. The only way I knew I was in download was when I saw the yellow band appear in Odin. Open Odin, and try different button combinations that will get you into download mode until you see Odin recognize your phone.

I'm sure you've tried, but these are 2 other key combos. I've had that happen to me in the past and it can be frustrating.
1. volume up + volume down
2. volume down + power
3. volume down + home (softkey) then power (this is the one that worked for me)
4. volume down + menu (softkey) then power
Hope everything works out for you. If all else fails, I'm sure a jig will work.

I learned this in the days of old, when we were flashing the baked Froyo's. Don't know if it applies or if you've tried it already, but what used to work for me was:
Open Odin
Pull the battery out, put it back in...don't turn it on.
Hold the volume down button
Plug in the usb
At no point in the process should you ever touch the power button. For your Odin version, I'd recommend using the Stock Odin, get factory and then try flashing your custom Rom again.
(Edit: I say volume down because that's the current button to enter download mode with Gingerbread. It used to be Volume Up and Down at the same time.)

ok first this does not belong in the dev section! belongs in Q&A so thing will get closed pretty soon. also other than a correct jtag u cant recover with jig, button combo or voodoo magic. u just mixed a i9000 GB bootloader along with a captivate froyo secondary boot which the Cog4 ROM has. use search and i think you can find someone who offers a jtag service

Well, I've seen a few mention it, but I think your going to need to make or puchase a jig. Hit radioshack and get 3 100kohm resistors, about $1. The directions are all over the forums here. I'd be willing to bet that will fix you up.
Also, once in a while it may still be alive even though the screen is black. Like someone else said, go ahead and start Odin, then plug your phone into USB. See if there is any response from Odin. It's worth a shot.
Either way, it's good to have a Jig handy.

claim warranty.

Odin 1 click to stock then start from scratch!

EsotericSYN said:
Odin 1 click to stock then start from scratch!
Click to expand...
Click to collapse
you need dl mode to do that, he's not even getting power up. go to att store and say it wont turn on today gimme replacement.

How did someone with just 2 posts make a thread in here? I thought you had to have 10+ posts just to post in a thread.

just contact samsung the captivate should be in warraty untill oct2011.. i also bricked my phone while on serendipity VII see Q&A Soft brick or hard Brick.i had my phone stuck on the battery charge screen. was not able to get to download mode or recovery and my battery wouldnt charge . so i called samsung just gave them my imei number and they said it was under warranty until oct 2011. i did not tell them i bricked it while flashing roms. i just told them my phone wont charge or turn on. i sent my phone to the samsung repair center in dallas tx. my phone was fix at no charge even though i had it rooted and running a custom rom. samsung just fixed my looping battery screen and put there stock froyo erasing all my apps and data.it took about 2 weeks to get all this done. got my phone back this monday and everything is working great....
so just contact samsung and say the phone wont turn on dont say you rooted it or flashed a room. samsung wont check to see if its rooted all they care about is that you didnt drop the phone or something like that.

cremefraiche said:
ok first this does not belong in the dev section! Belongs in q&a so thing will get closed pretty soon. Also other than a correct jtag u cant recover with jig, button combo or voodoo magic. U just mixed a i9000 gb bootloader along with a captivate froyo secondary boot which the cog4 rom has. Use search and i think you can find someone who offers a jtag service
Click to expand...
Click to collapse
listen to this man

Same exact thing happened to me on my last phone. Your phone is dead, dead, dead. Hard bricked. Nothing will bring it back. Take it to an AT&T store and tell them you were upgrading to 2.2 and the screen went black and now it wont come back on.
There is no jig or JTAG that will fix it, trust me, I tried

timbrendelaz said:
Same exact thing happened to me on my last phone. Your phone is dead, dead, dead. Hard bricked. Nothing will bring it back. Take it to an AT&T store and tell them you were upgrading to 2.2 and the screen went black and now it wont come back on.
There is no jig or JTAG that will fix it, trust me, I tried
Click to expand...
Click to collapse
at&t might help, but you have to hassle alot.Just contact samsung they will help for sure.i just sent them my bricked phone and they fixed it in two weeks at no charge. samsung will do it for free, im living prof.

I dont really buy into the fact that its dead, no way... its just that the revisions on the boot.bin and sbl.bin are different... shouldn't JTAG work? and cant claim warranty cuz im not in the US!!! there must be a way people.... im faar too poor to just give up without a fight!!!

[Q] PROPERLY BRICkEd SAMSUNG GALAXY S I9000's ONLY - (no screen response)

hi iv had a serious journey with my sgs i9000 here's how it goes:
i had it on 2.2 and then upgraded it officially to 2.3.3
not much else happened until i realised i wanted voodoo sound (apparently it was hyped to be awesome....its not that great) and neither is the ext4 file system 2.3.3 seems to be just as fast...dont know if it was a major problem on 2.2 but it aint really on 2.3.3
so i flashed voodoo on 2.3.3 from some website ... downloaded the app for the sound as the kernel didnt support that...
then i was using it and played around with the settings in clock work manager and i mounted and unmounted sd/card i dont think it made much difference but i thought i'd mention it ... the reason i did this is because when i tried to load a rom it wouldnt find all my sd card files beyond like the first 5 folders so i thought i'd give it a kick start....
then what happened is the phone just went off and i couldnt get it back on.... little did i know this was soft brick... i didnt know why....
i got the computer screen with the phone and exclamation mark.... i got into download mode a few times....
NOW .... i cant get it to turn on AT ALL using any combo buttons....
i think the nail in the coffin was flashing it with the "one-click odin" which was for the captivate but it said i could use it on the i9000 too.... which blatently screwed up the device....
anyway iv ordered a jig device... if this gets me into download mode ....what am i supposed to do...?
also is there anything i can do to get it into download mode now ? (bearing in mind iv done all the combo's ... some people say leave the battery out for a couple of minutes or half an hour....)
i think the bootloader is screwed up because it doesnt switch on....
even after i did a clean install of 2.3.3 with the pda phone and csc roms... it still just randomly switched off after 2/3 minutes of boot time....
what do i do now ?
samsung repair centre said they couldnt do anything and i'd have to send it back to samsung.... is it that bad?

Tried all the combos.... So you tried plugging in combo, then battery and also holding combo and then battery without cable in...
Have you read the pinned thread in general i think it is regarding, bricks?
Moving on
how did you do a clean install of 2.3.3 if you couldn't get DL mode??
Haven't read into the one click Odin so can't comment on that, but i think that was meant to be for softbricks...
anyway regarding the jig, just plug it in, and then wait a second or so, of not a minute (usually instant) and it should go into download mode. If it doesn't work again try some combos with the jig in...
If it is a hard brick i think you need to J-tag it, or yes take it to samsung in which case they may charge you for a repair, unless you say kies did it, and you didn't tell them everything you didi when you spoke to em.
Think thats everything lemme know if i missed out a question of yours or you want something better explained etc..

yeah i guess i was vague on the combo thing...
i've tried:
a) holding power, menu and volume down while sliding battery in (no usb cable in )
b) same as above with usb cable in
c)just menu and volume down buttons while i put battery in
d) both volume buttons and cable in
e)both volume buttons and battery in
.... the reason for d and e is because when i flashed it with the one click odin installer thing.. it restarted and showed a a t&t screen so i think its flashed the software with a samsung capacitive rom....so in theory i need to use those buttons ? not sure .... yet more questions....
i just hope this jig thing works ... btw do i have to pay sammy is my phone is under warranty?
how do i reflash the bootloader so it works properly? is that even the problem? do i need to do that? which pit file do i use ? some people say 512.... some say thats outdated and the new pit file is the thing to use .. ?
Talon26 said:
Tried all the combos.... So you tried plugging in combo, then battery and also holding combo and then battery without cable in...
Have you read the pinned thread in general i think it is regarding, bricks?
Moving on
how did you do a clean install of 2.3.3 if you couldn't get DL mode??
Haven't read into the one click Odin so can't comment on that, but i think that was meant to be for softbricks...
anyway regarding the jig, just plug it in, and then wait a second or so, of not a minute (usually instant) and it should go into download mode. If it doesn't work again try some combos with the jig in...
If it is a hard brick i think you need to J-tag it, or yes take it to samsung in which case they may charge you for a repair, unless you say kies did it, and you didn't tell them everything you didi when you spoke to em.
Think thats everything lemme know if i missed out a question of yours or you want something better explained etc..
Click to expand...
Click to collapse

ok now iv got it to turn on quite regularly .... but it keeps cycling (bootlooping) the at&t logo screen .... cant get into download mode or recovery mode.... just keeps boot looping.... oh and when i plug in the usb cable it just turns off.... its like i cant start it up with a usb in the phone...
update: been reading around and if anyone has this problem.... it looks like you might be hard bricked and apparently this cant be resolved via jig device..... dammit ...i'll still try and update the post... peace

So you haven't tried the jig yet?? because you haven't got it yet right
I don't think the device is bricked at all. Bricked usually means you have no response from it, so no matter what combo, actions you take you get no reaction.. However you are getting a boot although there is something going wrong as it does so...
So yes you need a new bootloader, i think every rom that you flash through odin has one, but i guess it may not, its best to search this, but i have read a few posts that say you need to click on update bootloader (i would check into this, as if this is wrong it will definitely brick your device)
My suggestion is go back to the onclick odin thing as that should do it, im sure someone has done something similar.
Yh so to sum up, i would have high hopes for a restoration (but what so i know ) and yes flashing a new bootloader with rom i reckon would do the trick. I think a stock rom will do it. Click on the stock rom link below and type in a few search terms in that thread to see if you pick up anything otherwise do a slightly wider one of the forum.

Talon26 said:
So you haven't tried the jig yet?? because you haven't got it yet right
I don't think the device is bricked at all. Bricked usually means you have no response from it, so no matter what combo, actions you take you get no reaction.. However you are getting a boot although there is something going wrong as it does so...
So yes you need a new bootloader, i think every rom that you flash through odin has one, but i guess it may not, its best to search this, but i have read a few posts that say you need to click on update bootloader (i would check into this, as if this is wrong it will definitely brick your device)
My suggestion is go back to the onclick odin thing as that should do it, im sure someone has done something similar.
Yh so to sum up, i would have high hopes for a restoration (but what so i know ) and yes flashing a new bootloader with rom i reckon would do the trick. I think a stock rom will do it. Click on the stock rom link below and type in a few search terms in that thread to see if you pick up anything otherwise do a slightly wider one of the forum.
Click to expand...
Click to collapse
jig arrived today! .... i plugged it in ..... NOTHING ..... (read on theres more to the story!!!)
so i put it in nothing happened...... i thought maybe the jig device was not working so i tried it in the i9100 (s2) .... WORKED ...!
im really stubborn so i needed to make mine work too..... i read in a review of the jig device that someone bought one and it hadnt worked .... i hadnt ruled that out
anyway all day i just kept trying to jump start it by putting in the wall charger in and out ... i usually get some reponse from that....nothing apart from a second of something like a loading circle......
anyway then i left it on charge for an hour ....maybe the battery was dead and then tried again ....
(btw i was getting no response at all at this stage, not even the at&t thing ...)
so it was pure black screening me.....
then i got home from work and thought let me exchange the battery and see what happens....
i changed the battery and put the jig device in ...... VOILA !!! download mode....
all is well so far i've flashed with 2.3.3 pda,phone and csc files and checked repartition... i haven't messed with the bootloader option
seems to be working ok....also gave it a restart too ... last time it got to this point but it didnt turn back on after a restart ....
in conclusion .... charge battery fully externally (putting the power in the phone in this state was not charging it)
then with a full battery put jig in .... if that doesnt work you phone might be seriously bricked.... bravo to whoever dreamt up the jig device

Glad to hear the great news!

Nice
Thanks for this useful info

[Q] I CAN'T root my phone (2.2 froyo, factory reset)

Here is what I've tried so far:
1- SuperOneClick. The program hangs at a step where it reads "Check if rooted : false"
2- Galaxy One Click Root. Program is responsive but it stops at "* daemon started successfully *" and does nothing from there.
3- Copying the "update.zip" file to the root of my internal SD card. I'm greeted by a "E: Signature verification failed. Installation aborted" error.
All remediable steps to fix one or all problems REQUIRES root, so i'm in limbo here. I honestly am about to cry. This seemed a hell of a lot easier when I read about it...
Well, what's left here for me to do? I'm lost. I read so many threads here I honestly can't do it anymore. This is my last resort.
This phone is all stock, AT&T Captivate.
Sorry if this is the wrong section of this forum... New here.

Flash your phone via Odin to jf6 stock then try superoneclick
Sent from my SPH-D710 using XDA App

hold up on that flash back. It oculd cause you to loop. Try using SOC v1.9 or lower. Also make sure your computer has all the required updates installed.

So this developed into a new, bigger, problem. I tried THIS guide to flash cyanogenmod (latest) but, guess what, the freaking thing hanged. So I was left with the only option, severing the link between PC and phone, and rebooting the phone.
I get this "phone - attention sign - computer" image. I think to myself "oh sh#&, I bricked the phone" so I rebooted it once again and to my surprise, the phone won't turn on. Won't react to the usb cable (can't boot to download mode), won't react to wall charger, won't turn on with the power button.
The battery was almost full...
What the heck is going on!?!? I had this phone for 3 days and I already ruined it?
I wan't to kill myself

leandroab said:
So this developed into a new, bigger, problem. I tried THIS guide to flash cyanogenmod (latest) but, guess what, the freaking thing hanged. So I was left with the only option, severing the link between PC and phone, and rebooting the phone.
I get this "phone - attention sign - computer" image. I think to myself "oh sh#&, I bricked the phone" so I rebooted it once again and to my surprise, the phone won't turn on. Won't react to the usb cable (can't boot to download mode), won't react to wall charger, won't turn on with the power button.
The battery was almost full...
What the heck is going on!?!? I had this phone for 3 days and I already ruined it?
I wan't to kill myself
Click to expand...
Click to collapse
Unfortunately, it doesn't sound promising. Even if you have a black screen, I would still try to access DL mode with Odin open (pull battery, remove sim, put battery back in, hold both volume buttons and insert the USB cord, don't touch the power button). If you get a yellow com light in Odin, even if the screen stays black, you're in download mode. If that doesn't work, you could try a jig and then see if Odin recognizes it. If neither of those work, you'll need to send your phone out to someone like Adam Outler to have it unbricked.

I get nothing with Odin. I can't believe I bricked my phone like that. I thought I would get an error screen at least. But this is outrageous. It's like the phone shorted and fried from the inside.
All I can say is wow... My happiness of a new phone turned to ashes in 30 seconds. Nice waste of money.

If you buy a USB download jig it will get you out of soft brick situations and if Odin fails try heimindal
Sent from my SPH-D710 using XDA App

leandroab said:
I get nothing with Odin. I can't believe I bricked my phone like that. I thought I would get an error screen at least. But this is outrageous. It's like the phone shorted and fried from the inside.
All I can say is wow... My happiness of a new phone turned to ashes in 30 seconds. Nice waste of money.
Click to expand...
Click to collapse
It didn't fry, it failed while flashing bootloaders. The bootloaders are what tell your phone what to do when you press power. Mismatched bootloaders = hard brick = no power up.
I would still try a jig, but if that doesn't work send a message to AdamOutler. He can give you the details of getting it unbricked.

MJHawaii said:
If you buy a USB download jig it will get you out of soft brick situations and if Odin fails try heimindal
Sent from my SPH-D710 using XDA App
Click to expand...
Click to collapse
Considering the flashing hanged at the very beggining, I'm 90% sure it HARD-bricked my device. A jig wouldn't work and I'm left with a very fancy paperweight.
There is NO power on whatsoever.
My luck is amazing, isn't it?
Please, someone tell me there is still hope (there isn't probably)
apbthe3 said:
It didn't fry, it failed while flashing bootloaders. The bootloaders are what tell your phone what to do when you press power. Mismatched bootloaders = hard brick = no power up.
I would still try a jig, but if that doesn't work send a message to AdamOutler. He can give you the details of getting it unbricked.
Click to expand...
Click to collapse
Exactly. I figured
I have no idea of who "AdamOutler" is. But I'll find out. :/
FML

leandroab said:
Considering the flashing hanged at the very beggining, I'm 90% sure it HARD-bricked my device. A jig wouldn't work and I'm left with a very fancy paperweight.
There is NO power on whatsoever.
My luck is amazing, isn't it?
Please, someone tell me there is still hope (there isn't probably)
FML
Click to expand...
Click to collapse
I suspect you are correct about the hard brick, but I would still try a jig. I had a failure flashing bootloaders once that killed my cappy, but though a stroke of fortune a jig still worked for me. You can build one for a couple of bucks of parts from Radio Shack, you've got nothing to lose. If not, it can be repaired.

Before you start looking at all that, make sure you are hard bricked. Easiest way is to use Linux Mode Detector. Use the link below labeled Captivate sig link, then choose am i bricked?.

apbthe3 said:
I suspect you are correct about the hard brick, but I would still try a jig. I had a failure flashing bootloaders once that killed my cappy, but though a stroke of fortune a jig still worked for me. You can build one for a couple of bucks of parts from Radio Shack, you've got nothing to lose. If not, it can be repaired.
Click to expand...
Click to collapse
Yes, it's still worth a try. But unfortunately it will have to wait at least till the end of the month. That's when my college break is over and I'm back to school.
mrhaley30705 said:
Before you start looking at all that, make sure you are hard bricked. Easiest way is to use Linux Mode Detector. Use the link below labeled Captivate sig link, then choose am i bricked?.
Click to expand...
Click to collapse
Sorry but I'm not installing an OS just to use a program. I do believe the phone is hard-bricked though:
1- Doesn't power up with the on/off button
2- Doesn't go into recovery mode
3- Doesn't go into download mode
4- Doesn't light up when plugged into wall charger
If that isn't hard-bricked, then I'm really scared to find out what that really is
I sent a PM and an email to Adam Outler. I hope he replies it!

Linux is easier to use than you think, and it's a really handy tool to have when working with Android phones. You can install Linux entirely to a cheap thumb drive (I have a $4 4gb thumb drive running lubuntu) and it can get you out of a lot of Android related jams. If you're not willing to go through letting Linux up and running, might not want to do too much with phones either. I don't mean to be snarky, but I started using Linux casually a couple years before I started messing with phones and Linux is much more straightforward.
Edit: and if you have a multimeter around, check the voltage of your battery. Should be 4.2v=full, 3.5v ish is dead. If you battery pull, reinsert, hold volume up and down, and then connect to your pc with Odin open (don't hit power) what does Odin show? Last, did you get this phone used? Battery may be completely worn out, which would be why it was almost full and looks hard bricked now.

Wubi installer would be a better choice. And when your finished, it uninstalls just like an app. It's kind if a semipermanent dual boot. Check it out.

sekine12 said:
Linux is easier to use than you think, and it's a really handy tool to have when working with Android phones. You can install Linux entirely to a cheap thumb drive (I have a $4 4gb thumb drive running lubuntu) and it can get you out of a lot of Android related jams. If you're not willing to go through letting Linux up and running, might not want to do too much with phones either. I don't mean to be snarky, but I started using Linux casually a couple years before I started messing with phones and Linux is much more straightforward.
Click to expand...
Click to collapse
Well, I guess I'll look into that now. I'm running windows over a MacBook (stuck with it till I get back home). Maybe some tips running linux w/ a pendrive with bootcamp?
sekine12 said:
Edit: and if you have a multimeter around, check the voltage of your battery. Should be 4.2v=full, 3.5v ish is dead. If you battery pull, reinsert, hold volume up and down, and then connect to your pc with Odin open (don't hit power) what does Odin show? Last, did you get this phone used? Battery may be completely worn out, which would be why it was almost full and looks hard bricked now.
Click to expand...
Click to collapse
I'll look into the multimeter. The phone IS used, but I'm sure the battery isn't worn out.
Hooking up the phone, pressing both volume buttons, with odin open gives me nothing. Zip. If it was the battery wouldn't the phone give some sign of life after charging it for a while? Didn't happen.
mrhaley30705 said:
Wubi installer would be a better choice. And when your finished, it uninstalls just like an app. It's kind if a semipermanent dual boot. Check it out.
Click to expand...
Click to collapse
As stated, using windows with bootcamp over a MacBook. Maybe you can help me out? Will this work?

leandroab said:
If it was the battery wouldn't the phone give some sign of life after charging it for a while? Didn't happen.
Click to expand...
Click to collapse
My understanding is that charging is controlled by firmware to protect the battery, so it won't even charge if it's bricked.

apbthe3 said:
My understanding is that charging is controlled by firmware to protect the battery, so it won't even charge if it's bricked.
Click to expand...
Click to collapse
Right, or if the battery is so dead it can't start to turn on, it won't turn on. Or, if it was soft-bricked with no images to display, it may have killed itself without a firmware to allow it to charge properly. Not very likely, but there are a couple possibilities that end with a dead battery and no way to know.

apbthe3 said:
My understanding is that charging is controlled by firmware to protect the battery, so it won't even charge if it's bricked.
Click to expand...
Click to collapse
sekine12 said:
Right, or if the battery is so dead it can't start to turn on, it won't turn on. Or, if it was soft-bricked with no images to display, it may have killed itself without a firmware to allow it to charge properly. Not very likely, but there are a couple possibilities that end with a dead battery and no way to know.
Click to expand...
Click to collapse
Right. I'll check the V of the baterry once I get my hands on a multimeter.(somebody took all of them here at the house for some reason)

The multimeter read that the battery has 3.92V, so it's not dead. So to sum it up I only have two options now:
1- Try a USB jig
2- Attempt the UnBrickable mod/send it to Adam Outler
Both of them will take time. Unfortunate for me. Good news is that WILL have it back up and running. It will just take some time

leandroab said:
The multimeter read that the battery has 3.92V, so it's not dead. So to sum it up I only have two options now:
1- Try a USB jig
2- Attempt the UnBrickable mod/send it to Adam Outler
Both of them will take time. Unfortunate for me. Good news is that WILL have it back up and running. It will just take some time
Click to expand...
Click to collapse
So nothing whatsoever shows up in ODIN when you 1- batt pull, 2- batt reinsert, 3- plug in USB while holding either volume down, or volume up + vol down (w/o turning phone on)?

[Q] I messed up. Can get into download mode that's all..

I hope someone can help me here, I'm posting with the belief that this may be a simple enough problem (With the hope).
I tried to install a Custom Recovery on my Galaxy S using this tutorial - wiki.cyanogenmod.org/w/Install_CM_for_galaxysmtd
I managed to get to step 6, and a blue bar appeared, but then i could not do step 7.
Now i cannot boot into recovery mode, nor will the phone boot past the Samsung Galaxy S logo.
I can still get into download mode, but Odin does not detect the phone.
. I have changed cable and tried different versions of Odin..
When i turn on the phone normally it shows the Samsung Galaxy S logo, blinks, and then reboots and does the same.
When i try to enter recovery, i get the same, unless i connect it to the PC. I then get an 8 pointed star, like the loading flash circle thing - the same as a flash video loading except it does not move.
I have also removed the battery and tried to enter recovery and download mode while inserting the battery.
I have removed the SIM and battery for a few minutes.
when i try to start Zadig, with the phone connected in Download mode, i get "Gadget Serial" as the device connected. I used to get "Samsung USB Composite Device"
I have tried many different things and read over the recommended threads on this forum. I think i need a bit more pointing in the right direction.
I really hope somebody can help me. I am very worried that i may have bricked it.
Thank you.

Try this:
This feature is great for people who
a) Have a bad KIES flash
b) Stuff up their phone somehow
c) Accidentally flash something dodgy via ODIN
d) Some other random occurence
To test this feature you just need to start with your phone turned off... Best way to be sure is to remove the battery.
Then
1. Put battery back in
2. Press and hold Volume Up + Home Key
3. Continue holding those buttons and then press and hold power button.
4. When you see the logo pop up release power button ONLY
5. Keep holding two buttons from step 2 until you enter recovery mode.
I hope this helps?
Also have you tried everything on this thread:
http://forum.xda-developers.com/showthread.php?t=1134975

akash6969 said:
Try this:
This feature is great for people who
a) Have a bad KIES flash
b) Stuff up their phone somehow
c) Accidentally flash something dodgy via ODIN
d) Some other random occurence
To test this feature you just need to start with your phone turned off... Best way to be sure is to remove the battery.
Then
1. Put battery back in
2. Press and hold Volume Up + Home Key
3. Continue holding those buttons and then press and hold power button.
4. When you see the logo pop up release power button ONLY
5. Keep holding two buttons from step 2 until you enter recovery mode.
I hope this helps?
Also have you tried everything on this thread:
http://forum.xda-developers.com/showthread.php?t=1134975
Click to expand...
Click to collapse
I hadn't seen that thread, but i have gone over tons of them Thanks for reply.
I eventually got Odin to detect it and I tried this - http://forum.xda-developers.com/showthread.php?t=1544487
It came up red and said failed.
I closed odin and disconnected the phone. Now i can't even turn it on.. Nothing. I am hoping the battery died, and it's a coincidence..
No response at all to any buttons... I haven't done anything else.
If i can get it to power up again, i'll try those tips.

Tomato_Jam said:
I hadn't seen that thread, but i have gone over tons of them Thanks for reply.
I eventually got Odin to detect it and I tried this - http://forum.xda-developers.com/showthread.php?t=1544487
It came up red and said failed.
I closed odin and disconnected the phone. Now i can't even turn it on.. Nothing. I am hoping the battery died, and it's a coincidence..
No response at all to any buttons... I haven't done anything else.
If i can get it to power up again, i'll try those tips.
Click to expand...
Click to collapse
Ok, Don't worry, Charge your phone battery to 100%, leave over night. ( keep charger connected to your phone overnight)
Best to have a fully charged battery in these situations!
Keep calm, and read and prepare what you want to do next.. Don't try everything in a frantic effort to get your phone started again.
I know it's difficult, but there are lots of threads on how to rectify most problems.
I wish you Good luck!!

sorry to ask some stupid question, but can u make sure what versiom ur fone is?
is it i9000?, or i9001 or i9003? or korean anycall? as far as i know, flashing i9000 ROM to i9003 will hardbrick da device.
Sent from my GT-I9000 using xda premium

akash6969 said:
Ok, Don't worry, Charge your phone battery to 100%, leave over night. ( keep charger connected to your phone overnight)
Best to have a fully charged battery in these situations!
Keep calm, and read and prepare what you want to do next.. Don't try everything in a frantic effort to get your phone started again.
I know it's difficult, but there are lots of threads on how to rectify most problems.
I wish you Good luck!!
Click to expand...
Click to collapse
Thanks.
This is a disaster. I tried to power it on to any mode there before i saw your post.
I needed to update the phone, because an app i needed for studying was only available on Android 4+.
Now no phone..
I saw a few threads, i hope after i leave it overnight i'll be able to power it.
If not, probably a JIG?
I don't fancy making one, but if i have to, i guess i'll give it a try. I don't think i could wait a week or more for a premade one to be delivered.
Anyway, for now, i'll keep my fingers crossed.
Thanks for help/tips and reply.
I'll post back tomorrow, hopefully with some better news.

Tomato_Jam said:
Thanks.
This is a disaster. I tried to power it on to any mode there before i saw your post.
I needed to update the phone, because an app i needed for studying was only available on Android 4+.
Now no phone..
I saw a few threads, i hope after i leave it overnight i'll be able to power it.
If not, probably a JIG?
I don't fancy making one, but if i have to, i guess i'll give it a try. I don't think i could wait a week or more for a premade one to be delivered.
Anyway, for now, i'll keep my fingers crossed.
Thanks for help/tips and reply.
I'll post back tomorrow, hopefully with some better news.
Click to expand...
Click to collapse
Sorry to say, most likely you will need a USB JIg to fix the problem you have. :/
If you linked the correct page when you said you tried to do this- and if I opened the correct page, that takes you to an SII section. Those are SII firmwares, not for the S.
So as compacity said, please clarify what device you have... Whether its an I9000 (galaxysmtd is for the I9000) or an I9100 (the firmware page you linked). If you do have an I9000, then your brick comes from flashing a different device's rom onto the S, which would give this error in Odin beause its incompatible.
In this case, you'd probably need a USB Jig to come out of it.
Try what the others said and hopefully you'll be at least able to enter Download mode before resorting to a jig, but considering your situation, I have to say realistically a jig is your best bet :/
Sent from my GT-P7510 using Tapatalk HD

You need a usb jig. It will get you into download mode. Now you need to flash cf root, which will come with cwm recovery. Recovery mode should work now. If you get computer!phone, then re-flash cf root. Now you should be able to flash CyanogenMod via cwm recovery. Thank if I helped!
Sent from my GT-I9000 using cm10.1

Soryuu said:
Sorry to say, most likely you will need a USB JIg to fix the problem you have. :/
If you linked the correct page when you said you tried to do this- and if I opened the correct page, that takes you to an SII section. Those are SII firmwares, not for the S.
So as compacity said, please clarify what device you have... Whether its an I9000 (galaxysmtd is for the I9000) or an I9100 (the firmware page you linked). If you do have an I9000, then your brick comes from flashing a different device's rom onto the S, which would give this error in Odin beause its incompatible.
In this case, you'd probably need a USB Jig to come out of it.
Try what the others said and hopefully you'll be at least able to enter Download mode before resorting to a jig, but considering your situation, I have to say realistically a jig is your best bet :/
Sent from my GT-P7510 using Tapatalk HD
Click to expand...
Click to collapse
huskyT said:
You need a usb jig. It will get you into download mode. Now you need to flash cf root, which will come with cwm recovery. Recovery mode should work now. If you get computer!phone, then re-flash cf root. Now you should be able to flash CyanogenMod via cwm recovery. Thank if I helped!
Sent from my GT-I9000 using cm10.1
Click to expand...
Click to collapse
Both helped a lot, thanks.
I had to end up bringing the phone to a repair shop
Something i am not inclined to do if i can avoid it. Especially if i caused it, i would hope i could undo it. But because i need a jig, and i wouldn't have time to get one or make one before Monday, i had to bring it to someone else.
I am buying the materials for a jig, and maybe going to buy one also, for future.
 @Soryuu - Yep, i linked to the page, so i must have flashed the wrong firmware.
I'm angry with myself because i read everything else carefully. I had been reading all day. I guess i was just tired and thought I had got to the final hurdle. I was careless.
@huskyT - Thanks, will know that for future reference. I have two old Android phones somewhere. One is a Galaxy Europa, and one is an LG (not sure what model). Both are borked in some way, but i could probably use them for practice. I think the Galaxy Europa is flashed badly. Not by me. (Thankfully).

Tomato_Jam said:
Both helped a lot, thanks.
I had to end up bringing the phone to a repair shop
Something i am not inclined to do if i can avoid it. Especially if i caused it, i would hope i could undo it. But because i need a jig, and i wouldn't have time to get one or make one before Monday, i had to bring it to someone else.
I am buying the materials for a jig, and maybe going to buy one also, for future.
@Soryuu - Yep, i linked to the page, so i must have flashed the wrong firmware.
I'm angry with myself because i read everything else carefully. I had been reading all day. I guess i was just tired and thought I had got to the final hurdle. I was careless.
@huskyT - Thanks, will know that for future reference. I have two old Android phones somewhere. One is a Galaxy Europa, and one is an LG (not sure what model). Both are borked in some way, but i could probably use them for practice. I think the Galaxy Europa is flashed badly. Not by me. (Thankfully).
Click to expand...
Click to collapse
Don't stress mate, we all have bad days, we all make mistakes
Sent from my GT-P7510 using Tapatalk HD

Well....
I would have been quicker if i had ordered a jig and done it myself.. (Worth mentioning, i had told guy in phone shop what happened, and about the required "jig")
I collected my phone from the shop today, after a week, and i was told "Your phone is f*****d". To which i replied, "what? are you sure, i mean, i have only flashed it with SGS2 firmware, i'm under the impression it is very hard to break/brick, if i have a jig."
He told me, "Nope, it's beyond repair, it won't work. If you want, i can use the screen and other parts, i'll buy it off you for €40"
No thanks.
So now i am on the lookout for a premade jig. Does anybody know where i can buy one?
I meant to last week, but things happened, and without a phone i was running around a bit...
I'm going to check ebay, but if somebody could recommend somebody reliable, i'd prefer that. Thanks.

I bought it from ebay, no problem...but just saw a couple of minutes ago that also on amazon germany these jigs are offered now/in the meantime....

rodman01 said:
I bought it from ebay, no problem...but just saw a couple of minutes ago that also on amazon germany these jigs are offered now/in the meantime....
Click to expand...
Click to collapse
Thanks.
I bought a jig, and it arrived today. Have phone in charger.
Do i just plug the jig in?
Or do i also do the three button press?
The screen is completely black, and nothing appears on it.

only plug the jig in, thats all... phone will start in download mode of its own. :fingers-crossed: :fingers-crossed:

rodman01 said:
only plug the jig in, thats all... phone will start in download mode of its own. :fingers-crossed: :fingers-crossed:
Click to expand...
Click to collapse
Thanks, going to leave it charging for a little longer, and try it.
If it doesn't work, would a motherboard for the Samsung Galaxy S be easy to replace? I have found one unlocked for €25.
EDIT
Found a tear down video here - http://www.youtube.com/watch?v=vxPWsLd05F4

yes thats not so difficult...only thing a bit complicated is to open the back or middle cover...but there are a few movies on youtupe where you can see how it can be opened and dismounted....btw for the first try with the jig battery has not to be that full...only if it starts in download mode and you can flash it via odin I would recommend to charge it complete.

rodman01 said:
yes thats not so difficult...only thing a bit complicated is to open the back or middle cover...but there are a few movies on youtupe where you can see how it can be opened and dismounted....btw for the first try with the jig battery has not to be that full...only if it starts in download mode and you can flash it via odin I would recommend to charge it complete.
Click to expand...
Click to collapse
Thanks again.
I am after removing it from the charger, and inserted the jig. It's in about 30 seconds now, and nothing is happening..

that sounds not good...ususaly it takes only a few seconds or perhaps a minute till it starts to download mode....sorry for no better news....

rodman01 said:
that sounds not good...ususaly it takes only a few seconds or perhaps a minute till it starts to download mode....sorry for no better news....
Click to expand...
Click to collapse
What seems to have happened, is i tried to flash it with SGS2 rom. So is it unbrickable?

I am not sure but I think that minimum the bootloader is damaged...there is one more possibility: to repair it via jtag...but for this you have to find someone, who ones one and can repair it....some of the guys don't take much money for such a repair, but with transport costs ets...perhaps it would be cheaper and faster if you take the new mainboard you mentioned.