Bricked Captivate?!?!? - Captivate Q&A, Help & Troubleshooting

Hi, I was using ODIN3 JF6 for porting my 2.2 to 2.1 eclair rom.. once the flashing done with no problem it gives me Reset phone.. then the phone reset it only shows me At&T logo continuosly again and again.. I tried to get on download mode in all ways but nothing.. adb doesn't recognize the phone and no com port on odin .... is it defintely bricked?????

early81 said:
Hi, I was using ODIN3 JF6 for porting my 2.2 to 2.1 eclair rom.. once the flashing done with no problem it gives me Reset phone.. then the phone reset it only shows me At&T logo continuosly again and again.. I tried to get on download mode in all ways but nothing.. adb doesn't recognize the phone and no com port on odin .... is it defintely bricked?????
Click to expand...
Click to collapse
If you can see a screen, it's not bricked. For download mode, did you try (from a powered-off state) holding Vol+ and Vol-, then inserting the USB plug? You may also have to take the battery out, hold v+/v-, insert plug, then insert battery.
If those don't work, look into getting yourself a jig.

jmtheiss said:
If you can see a screen, it's not bricked. For download mode, did you try (from a powered-off state) holding Vol+ and Vol-, then inserting the USB plug? You may also have to take the battery out, hold v+/v-, insert plug, then insert battery.
If those don't work, look into getting yourself a jig.
Click to expand...
Click to collapse
yes i get the AT&T logo infinite looping but no way to get download mode.. yes I even tried the vol+vol- ...

If those combinations aren't working for you, you will most likely need to either buy or make yourself a jig. It's not very expensive - either buy 3 resistors at an electronics store, or see if you can find one on Ebay. That's the easiest, most surefire way to get into download mode.
One last thing to try, though, just in case - try holding Vol- and Power from a powered-off state. That's the Gingerbread combination for i9000 bootloaders, but it won't hurt to try them.

jmtheiss said:
If those combinations aren't working for you, you will most likely need to either buy or make yourself a jig. It's not very expensive - either buy 3 resistors at an electronics store, or see if you can find one on Ebay. That's the easiest, most surefire way to get into download mode.
One last thing to try, though, just in case - try holding Vol- and Power from a powered-off state. That's the Gingerbread combination for i9000 bootloaders, but it won't hurt to try them.
Click to expand...
Click to collapse
no way I tried all combinations many times ..no way to get download mode.. i will keep on ebay the jig..many thanks ..i iwll let know in post if I ll solve this

Once you get into download mode, don't flash jf6 newer phones don't like that firmware and they do exactly what your's is doing. Bootloop and broken button combos.
Flash any other firmware other than jf6 and you'll be good.

studacris said:
Once you get into download mode, don't flash jf6 newer phones don't like that firmware and they do exactly what your's is doing. Bootloop and broken button combos.
Flash any other firmware other than jf6 and you'll be good.
Click to expand...
Click to collapse
where can I get a new firmware with Odin??.. I supposed the odin JF6 was the best for resuming 2.1 stock firmware.. can you please post me a link on xda of a similar odni firmware?
I used JF6 only beacuse on the forum it said that is the best for installing the i9000 bootloader and kernel... thanks

Here ya go... [Stock ROMs](OneClicks Master Collection)+[Kernels (Stock & w/ CWM)]+[Modems] UPDATED ---- These are all i897 firmwares, some with the choice of i897 GB Bootloaders included and some without.

ok I get the jig.. finally I get the download mode ,, I 'm trying to install the 2.3.3 kernel +bootloader UCKF1 is this ok?
thanks

early81 said:
ok I get the jig.. finally I get the download mode ,, I 'm trying to install the 2.3.3 kernel +bootloader UCKF1 is this ok?
thanks
Click to expand...
Click to collapse
That should work, as you're installing a Gingerbread Rom, you'll need the matching bootloaders.
Just make sure you have a good connection to your computer, and that your computer won't lose power in the process.

jmtheiss said:
That should work, as you're installing a Gingerbread Rom, you'll need the matching bootloaders.
Just make sure you have a good connection to your computer, and that your computer won't lose power in the process.
Click to expand...
Click to collapse
Hi, thank you all ,, all worked 100% .. one more thing.. why the bootloader is not the i9000 bootloader ? if I want to install the cm7 can I just install from market the rom manager?? .. and about the root+busybox .. does the super-one click works with 2.3.3 ?

early81 said:
Hi, thank you all ,, all worked 100% .. one more thing.. why the bootloader is not the i9000 bootloader ? if I want to install the cm7 can I just install from market the rom manager?? .. and about the root+busybox .. does the super-one click works with 2.3.3 ?
Click to expand...
Click to collapse
Glad to hear it worked.
- UCKF1 uses the AT&T Gingerbread bootloaders, not the i9000. You have the option to flash the i9000 ones separately, but I wouldn't recommend it, as there really isn't a pressing reason to put yourself in that danger.
- If you want to try CM7 again, I would recommend installing it separately from Rom manager - rom manager tends to be problematic.
- I don't think super one-click works with 2.3.x roms. You'll need to flash a kernel with CWM baked in (like boog's kernel) using Odin or Heimdall, then flash CM7.

- I don't think super one-click works with 2.3.x roms. You'll need to flash a kernel with CWM baked in (like boog's kernel) using Odin or Heimdall, then flash CM7.
Click to expand...
Click to collapse
thank you lot for helping me .. if I install directly this one:
With Bootloaders - Link 1 / Link 2 [With CWM Injected Kernel from Boog]
Boog includes recovrey.. so once install this I can get even recovery ready for cm7???

On the page of one-clicks, in this section:
I897UCKH3 Android 2.3.4 Gingerbread
With Bootloaders - Link 1 / Link 2 [With CWM Injected Kernel from Boog]
Heimdall Package, With Bootloaders - Link to thread - by AdamOutler
Without Bootloaders - Link to thread - by 4-2ndtwin [With CWM Injected Kernel from Boog]
Heimdall Package, Without Bootloaders - Link to thread - by jmtheiss [With CWM Injected Kernel from Boog] (Not tested)
Stock Kernel - Link 1 / Link 2
Kernel with CWM - Link to thread - by Boog
Use one of the two that I have left highlighted. If you want to use Odin, use the first one. If you prefer Heimdall, use the second one. Either one will get you to a stock state, with CWM, so that you can flash CM7. And, both will do this without flashing bootloaders. Definitely, no matter what, do not choose a package with bootloaders. You want a package that says "no bootloaders".

Use one of the two that I have left highlighted. If you want to use Odin, use the first one. If you prefer Heimdall, use the second one. Either one will get you to a stock state, with CWM, so that you can flash CM7. And, both will do this without flashing bootloaders. Definitely, no matter what, do not choose a package with bootloaders. You want a package that says "no bootloaders".
Click to expand...
Click to collapse
ok I did all ,,how to enter in recovery mode?? the vol down + power button isn' t working ...

early81 said:
ok I did all ,,how to enter in recovery mode?? the vol down + power button isn' t working ...
Click to expand...
Click to collapse
Recovery on your phone is now holding Vol+/Vol-/Power. Download will be Vol+/Vol- and inserting the USB cable.

jmtheiss said:
Recovery on your phone is now holding Vol+/Vol-/Power. Download will be Vol+/Vol- and inserting the USB cable.
Click to expand...
Click to collapse
... is not working.. it keeps showing me AT&T logo until I leave the power button,, but once i leave it starts normal use..and not recovery..
EDIT : WITH ADB REBOOT RECOVERY IT WORKS , IT GOES IN CWM 4.0.1.5 ,, TRYING TO INSTALL CM7 .. HOPE WILL WORK

You need a jig. I'm guessing your build number higher then 1010.
Sent from my I897 using XDA App

early81 said:
... is not working.. it keeps showing me AT&T logo until I leave the power button,, but once i leave it starts normal use..and not recovery..
EDIT : WITH ADB REBOOT RECOVERY IT WORKS , IT GOES IN CWM 4.0.1.5 ,, TRYING TO INSTALL CM7 .. HOPE WILL WORK
Click to expand...
Click to collapse
That's good to hear. Let us know if you need more help.

Idk what the deal is with 1010 builds, I have a 1012 build and everything works on it, even JF6 Odin one click!
Sent from my SAMSUNG-SGH-I897 using xda premium

Related

[Q] What kind of brick would this be considered and steps to fix it

My Captivate is currently in a state where it can boot up and it reaches the Cognition boot screen and does nothing further. When trying to use the 2 button+usb cord method to enter download mode the phone loads the charging battery but the animation is frozen.
Would this be considered a soft or hard brick? I'm not familiar with the factors that constitute the differences between the two. Is is a soft brick because the phone can still turn on or is it a hard brick because download mode is unreachable?
I was a user of Cognition 5 v1.00 but as support of the rom by the developer seemed to waiver I felt myself looking for a new GB Rom for my phone. I first flashed Cognition 4.5.3 onto my phone in order to have a stable Rom on my phone until I could decide upon the GB Rom I wanted to try. I decided to flash CM7 and began following the steps outlined in the thread. I formatted my system, data, and cache partitions but upon reboot I reached the point where I am currently.
I have not yet tried the jig as I do not have it on hand at my school apartment. Button combos, the usb cord, and the one click unbrick have not solved the problem and I would like to know if their are any other methods I could use to enter download mode until I am able to procure my jig and try that method.
Any help would be greatly appreciated.
Soft Bricked
You are whats considered soft bricked. Id recommend pulling out battery, SIM and SD. Open odin with with admin rights. Plug your phone to the computer, press volume up and down and insert battery. If that doesn't work then I would suggest making/buying a jig and flash back to stock (eclair, froyo or GB). As to how to get CM7 to work I can't offer any help since i haven't used it in a while and flashing method changed. I can recommend Atomic Fusion, KF1 based and very nice (after u theme it)
Clay
+1 I agree with prbassplayer. You have to get into dl mode and if none of the key combos work, then a jig is probably the only way. I use one and it works great in exactly the situation you seem to be in.
edit: Sorry for the double post, forget this and read next. :-/
Clay?
+1 I agree with prbassplayer. You have to get into dl mode and if none of the button combos work for you then the jig may be you're only option. I use it and it works great in exactly the same situation you seem to be in.
You might have crossed up some files and such from going back and forth between GB and Eclair. So need to flash back to stock and start over with fresh install.
If you're still interested in CM7, after rooting, you can install Rom Manager and follow the install process in the CM7 OP or check out their website, it'll walk you thru the whole thing.
Hope this helps
prbassplayer said:
You are whats considered soft bricked. Id recommend pulling out battery, SIM and SD. Open odin with with admin rights. Plug your phone to the computer, press volume up and down and insert battery. If that doesn't work then I would suggest making/buying a jig and flash back to stock (eclair, froyo or GB). As to how to get CM7 to work I can't offer any help since i haven't used it in a while and flashing method changed. I can recommend Atomic Fusion, KF1 based and very nice (after u theme it)
Click to expand...
Click to collapse
Thank you for the input. At this point it seems that the jig is the only option as I've already tried the usb cord volume up and down process to no avail. I already own a jig, I just need to find a way to my parents house to go grab it.
They aren't hard to make to be honest and if u have a micro usb cable u don't care for it only cost w/e resistors cost for you there.
Using the SDK to use adb commands to get into download mode isn't an option as mentioned in this thread here?
http://forum.xda-developers.com/showthread.php?t=819105http://forum.xda-developers.com/showthread.php?t=1198270&highlight=soft+brick#
TheDeveron said:
Thank you for the input. At this point it seems that the jig is the only option as I've already tried the usb cord volume up and down process to no avail. I already own a jig, I just need to find a way to my parents house to go grab it.
Click to expand...
Click to collapse
If you've already installed the GB bootloaders, the button combination has changed. I believe it is just volume down-power for gingerbread. Try that or volume up-power then release once the logo starts to see if that gets you into download or recovery.
trekie86 said:
If you've already installed the GB bootloaders, the button combination has changed. I believe it is just volume down-power for gingerbread. Try that or volume up-power then release once the logo starts to see if that gets you into download or recovery.
Click to expand...
Click to collapse
That's if he installed I9000's bootloaders. Im assuming he is on I897 bootloaders if he came from Cog 5.
TheDeveron said:
My Captivate is currently in a state where it can boot up and it reaches the Cognition boot screen and does nothing further. When trying to use the 2 button+usb cord method to enter download mode the phone loads the charging battery but the animation is frozen.
Would this be considered a soft or hard brick? I'm not familiar with the factors that constitute the differences between the two. Is is a soft brick because the phone can still turn on or is it a hard brick because download mode is unreachable?
I was a user of Cognition 5 v1.00 but as support of the rom by the developer seemed to waiver I felt myself looking for a new GB Rom for my phone. I first flashed Cognition 4.5.3 onto my phone in order to have a stable Rom on my phone until I could decide upon the GB Rom I wanted to try. I decided to flash CM7 and began following the steps outlined in the thread. I formatted my system, data, and cache partitions but upon reboot I reached the point where I am currently.
I have not yet tried the jig as I do not have it on hand at my school apartment. Button combos, the usb cord, and the one click unbrick have not solved the problem and I would like to know if their are any other methods I could use to enter download mode until I am able to procure my jig and try that method.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
download mode thru adb is a good idea...
or gb key combo for download mode as someone else also menioned...coz u r already on gb bootloaders..
prbassplayer said:
That's if he installed I9000's bootloaders. Im assuming he is on I897 bootloaders if he came from Cog 5.
Click to expand...
Click to collapse
but i think gb bootloaders...be it i9000 or i897....hav the same key combo to get to download mode..i m sorry if i m wrong..as i m on i9000 bootloaders...
^^^ you are wrong, the captivate boots have the same combos they've always had eclair/froyo/gingerbread
Only the I9000 boots have different combos.
studacris said:
^^^ you are wrong, the captivate boots have the same combos they've always had eclair/froyo/gingerbread
Only the I9000 boots have different combos.
Click to expand...
Click to collapse
as i already said...may be i m wrong..
thanx for the info...though i m on cappy ..but first gb botlaoders i had was i9000 while flashin apex..and m still on it....so didnt pay attention
i m using xda classin.so dont hav thanks button..so thanx here only..
killer_raj said:
download mode thru adb is a good idea...
or gb key combo for download mode as someone else also menioned...coz u r already on gb bootloaders..
but i think gb bootloaders...be it i9000 or i897....hav the same key combo to get to download mode..i m sorry if i m wrong..as i m on i9000 bootloaders...
Click to expand...
Click to collapse
No on Cog it is not. You can use the 3 button method just fine.
FYI GB bootloaders are not designed for CM7. CM7 used Froyo based bootloaders for its roms.

Bricked it again.. Help

Hi,
I bricked my captivate when I tried to install CWM after installing the 1 click odin 2.3 gingerbread.
I rooted it with the fugu and the kernel,
but CWM didn't work and I didn't know what to do..
So I tried to make a TAR file from the Update.zip,
tried to flash it trough odin in the PDA but it failed lol..
So now I'm stuck on the screen with designed phone and computer with the yellow triangle, telling me:
Firmware upgrade fail!
Try using recovery mode
Well, I tried to get to download or recovery without success,
I tried alot, combos with 1 volum and both, pressing volume keys and then connectin USB, it just won't work..
What should I do now?
Buy a jig.
Gibieyal said:
Hi,
I bricked my captivate when I tried to install CWM after installing the 1 click odin 2.3 gingerbread.
I rooted it with the fugu and the kernel,
but CWM didn't work and I didn't know what to do..
So I tried to make a TAR file from the Update.zip,
tried to flash it trough odin in the PDA but it failed lol..
So now I'm stuck on the screen with designed phone and computer with the yellow triangle, telling me:
Firmware upgrade fail!
Try using recovery mode
Well, I tried to get to download or recovery without success,
I tried alot, combos with 1 volum and both, pressing volume keys and then connectin USB, it just won't work..
What should I do now?
Click to expand...
Click to collapse
Try starting ODIN, removing battery connect phone to comp pres VOL up and down and insert battery. If that doesn't work get a jig. On a side note to get CWM on KF1 you need to use Cognition 5 kernel (step 2 in his thread).
It didn't work either..
I heard about the jig but I don't know anything about it,
can you give me a link or some explanation where to buy and how to get it work?
Gibieyal said:
It didn't work either..
I heard about the jig but I don't know anything about it,
can you give me a link or some explanation where to buy and how to get it work?
Click to expand...
Click to collapse
Search....
Captivate Directory (sticky)
How to make a Jig
Another How to make a Jig
You can also buy them in Ebay or in mobiletechvideos.com
Thank you very much,
Iv'e searched but the jig with the ohms and stuff looks scary..
So I have just ordered the SGS jig from mobiletech, hope it will work.
Thank again.
Gibieyal said:
Hi,
I bricked my captivate when I tried to install CWM after installing the 1 click odin 2.3 gingerbread.
I rooted it with the fugu and the kernel,
but CWM didn't work and I didn't know what to do..
So I tried to make a TAR file from the Update.zip,
tried to flash it trough odin in the PDA but it failed lol..
So now I'm stuck on the screen with designed phone and computer with the yellow triangle, telling me:
Firmware upgrade fail!
Try using recovery mode
Well, I tried to get to download or recovery without success,
I tried alot, combos with 1 volum and both, pressing volume keys and then connectin USB, it just won't work..
What should I do now?
Click to expand...
Click to collapse
If u can turn on ur phone and get the "Firmware upgrade fail", then u can use that screen to 1click Odin back to the i897uckf1 stock gingerbread. Just use that screen just like u would the download mode.
Sent from Stock I897UCKH3 / Fugu Rooted
Wow,
It worked lol!
Thank you very much for the note, now when the jig
will arrive I will stop annoying you guys : )
Gibieyal said:
Wow,
It worked lol!
Thank you very much for the note, now when the jig
will arrive I will stop annoying you guys : )
Click to expand...
Click to collapse
Thanks button dosent bite...
Firmware upgrade failed?
Why does it show firmware upgrade failed instead of just the standard phone ~!~ PC screen?
Because you failed flashing something and it messed it up. I believe the message is new because the GB bootloaders.
I believe its a secondary failsafe
Sent from my SGH-I897 using XDA Premium App
bulletproof1013 said:
I believe its a secondary failsafe
Sent from my SGH-I897 using XDA Premium App
Click to expand...
Click to collapse
Yup. You can still get Hard brick. Anoying little detail is it doesn't say its DL mode =/

wrong firmware on i9000

I accidentally installed a capitvate i897 firmware (Android 2.3.4, AT&T branded) on my i9000. It looks like an US firmware, mine should be German.
Since installation of the new firmware I can't use the usb-connection anymore - some seconds after plugging the phone resets and stops working until I unplug the cable again. The 3-button-trick doesn't work anymore either, probably because the captivate hardware is quite different.
So... now I am desparately looking for any help or hints how I can get my phone rootet. I think that would help a lot to install a proper firmware again (via mobile odin).
Any hints?
Gingerly said:
I accidentally installed a capitvate i897 firmware (Android 2.3.4, AT&T branded) on my i9000. It looks like an US firmware, mine should be German.
Since installation of the new firmware I can't use the usb-connection anymore - some seconds after plugging the phone resets and stops working until I unplug the cable again. The 3-button-trick doesn't work anymore either, probably because the captivate hardware is quite different.
So... now I am desparately looking for any help or hints how I can get my phone rootet. I think that would help a lot to install a proper firmware again (via mobile odin).
Any hints?
Click to expand...
Click to collapse
You wouldn't really be going wrong by flashing back with Odin. I'd recommend flashing stock JW4 which is the latest European Gingerbread and rooting with the JW4 CF-ROOT.
I would have flashed already if I knew how to do it USB doesn't work, and entering recovery mode (if it is available, which I doubt) doesn't work either because I can't press the right buttons.
Gingerly said:
I would have flashed already if I knew how to do it USB doesn't work, and entering recovery mode (if it is available, which I doubt) doesn't work either because I can't press the right buttons.
Click to expand...
Click to collapse
u need to download 3 file odin from here http://www.hotfile.com/dl/150483619/708026d/I9000XXJW4_I9000OXAJW4_XEU.zip.html
and u will need also odin program from here http://www.filecrop.com/Odin-1.85.html after u download the firmware extract it and open odin
then put code in pda box modem on phone box an csc on csc box after that push vol down+home+power for download mode conect your phone to the computer and wait for yellow light in the program after thet press start good. luck btw if its only one file firmware put it on pda only
and if download mode not work with 3 button comb try jig device
Thanks for your detailed answer. But the 3-button-combo doesn't work. My guess is that the phone expects the captivate combo (volume up + volume down + power) which isn't possible on an i9000 device.
A jig might be worth a try, though I am worried, because the phone crashes always as soon as it get's power via usb (phone-pc or phone-power suppy, in both cases the phone crashes).
Is it possible to root the phone via wifi or right on the phone via app or some weird linux command line stuff?
You could try z4root? I don't think it will work but worth a try
Sent from my GT-I9000 running remICS-UX using XDA premium
Gingerly said:
Thanks for your detailed answer. But the 3-button-combo doesn't work. My guess is that the phone expects the captivate combo (volume up + volume down + power) which isn't possible on an i9000 device.
A jig might be worth a try, though I am worried, because the phone crashes always as soon as it get's power via usb (phone-pc or phone-power suppy, in both cases the phone crashes).
Is it possible to root the phone via wifi or right on the phone via app or some weird linux command line stuff?
Click to expand...
Click to collapse
Yes, I think it's worth a try, to download a SGS Kernel and try the App "SGS Kernel Flasher" (Search in Playstore, can't post a link) Maybe it works! I think you won't be able to boot your system after that, but maybe you can use the 3 button combo after that.
But first you have to find a way to root the phone... i can't find a app for that atm, maybe someone else found one?
------------------------------------------------------------------------------
EDIT
------------------------------------------------------------------------------
If you get root working, you can safely use this to flash the right firmware for your phone: http://forum.xda-developers.com/showthread.php?t=1347899
It's Odin on your mobile, so you can copy the files via an ftp or something like this and flash them to solve ur problem.
The other method I listed is a bit unsafe i think...
Actually, you can press Volume Up and Volume Down at the same time on a SGS. I tried it, because CM9 has the feature to change ringer mode this way.
nahum05 said:
u need to download 3 file odin from here http://www.hotfile.com/dl/150483619/708026d/I9000XXJW4_I9000OXAJW4_XEU.zip.html
and u will need also odin program from here http://www.filecrop.com/Odin-1.85.html after u download the firmware extract it and open odin
then put code in pda box modem on phone box an csc on csc box after that push vol down+home+power for download mode conect your phone to the computer and wait for yellow light in the program after thet press start good. luck btw if its only one file firmware put it on pda only
and if download mode not work with 3 button comb try jig device
Click to expand...
Click to collapse
Hello, More or less had the same problem.
To tell you the history: updated my samsung galaxy S I9000 to ICS, was not happy with it and f*cked up after that.
Wanted to install older firmware over ICS, telephone dead and than came on this forum and used
stockrom of I896 from developer TRusselo : http://forum.xda-developers.com/showthread.php?t=979133
now phone thinks he is a canadian I896.... Tried the above steps on PDA... unpacked ok but now phone keeps rebooting after it shows the samsunglogo....
did i miss a final step or did i do something wrong?
Thanks for your help in advance...
@calumn96: I tried z4root, it doesn't work..
@coroner21: wow! I always thought the both volume buttons would exclude each other. Now I can enter CWM.
Is there a way to root the i9000 in CWM? Or even better, to install a stock i9000 firmware?
Current situation: i897-firmware (2.3.4 uckh3) - I guess I need a root patch for this firmware.
Gingerly said:
@calumn96: I tried z4root, it doesn't work..
@coroner21: wow! I always thought the both volume buttons would exclude each other. Now I can enter CWM.
Is there a way to root the i9000 in CWM? Or even better, to install a stock i9000 firmware?
Current situation: i897-firmware (2.3.4 uckh3) - I guess I need a root patch for this firmware.
Click to expand...
Click to collapse
If you get a rooted i879 kernal you could try flashing that in cwm? You could try flashing a custom gb ROM from it (put files on a as card then in phone so not to use USB)
Sent from my GT-I9000 running remICS-UX using XDA premium
Gingerly said:
@calumn96: I tried z4root, it doesn't work..
@coroner21: wow! I always thought the both volume buttons would exclude each other. Now I can enter CWM.
Is there a way to root the i9000 in CWM? Or even better, to install a stock i9000 firmware?
Current situation: i897-firmware (2.3.4 uckh3) - I guess I need a root patch for this firmware.
Click to expand...
Click to collapse
Go into download mode
for i9000 it's volume down + home + power
for i897 it's both volume keys, and with the usb cable into the phone + power.
If you see the yellow triangle with and android and a shovel that's it!
Then get a stock firmware for i9000 on www.smafirmware.com and flash it through odin with the .pit + 3 files (PDA + MODEM + CSC).
@calum96: I will give it a try.
@-m3ta- : USB doesn't work, so any tips involving a usb-cable won't help :/
Another thing I realized is that recharging is barely possible...
Odin and Samfirmware is the way to go
Sent from my GT-I9300 using Tapatalk 2
Gingerly said:
@calum96: I will give it a try.
@-m3ta- : USB doesn't work, so any tips involving a usb-cable won't help :/
Another thing I realized is that recharging is barely possible...
Click to expand...
Click to collapse
I don't understand why 3 combo key, USB won't work. I had flash a captivate firmware onto the i9000 and the regular trick worked
@MrAndroid12: I don't understand it either. But the phone crashes as soon as the usb is plugged. Recharging didn't work at all, the phone just got hot and that's it.
@calum96: thank you! I flashed dmore 3.3 and so far it looks good. No usb-crashes anymore and the phone acts as it should. There is still an AT&T-brand, but that's still better than a useless phone
Gingerly said:
@MrAndroid12: I don't understand it either. But the phone crashes as soon as the usb is plugged. Recharging didn't work at all, the phone just got hot and that's it.
@calum96: thank you! I flashed dmore 3.3 and so far it looks good. No usb-crashes anymore and the phone acts as it should. There is still an AT&T-brand, but that's still better than a useless phone
Click to expand...
Click to collapse
You might be able to change the brands thing in build.props? Not sure tbh
So is it on i9000 firmware now? or is it just rooted? And is USB working now?
Sent from my GT-I9000 running remICS-UX using XDA premium
Everything works like a charm now
i9000 firmware (slim ics right now), usb works, recharging works and people can finally call me again (didn't work before either)
Thanks again for all your help, guys!
Glad to hear try remics its really good smooth with a Samsung feel
Sent from my GT-I9000 running remICS-UX using XDA premium

[Q] Stuck in boot loop

Hey everyone. I looked around the forums for a situation similar to mine, and didn't find a case exactly the same as mine, though it's possible I missed something. Basically, my little sister said her captivate was randomly shutting down lately, so I decided to root it for her. I rooted my own HTC Inspire this summer with no problems, so I figured I should be able to do it. The root went just fine, but when I tried to get into 3 button recovery mode, it wasn't working. I had read some stuff (obviously not well enough) and read somewhere to install the speedmod kernel. Now I'm stuck in a boot loop and can't get off of the Galaxy S/SGH-I897/SAMSUNG screen. I tried to go into download mode, but now I can't get into that mode either. Any ideas? I read on the forums about making a JIG, and I might have to end up doing that, but if I can avoid it, I'd like to. Thanks in advance.
Depending on what stock rom u were on before that flash of the speedmod kernel, it may not boot ur phone, because i believe it was froyo based. And if u got it from TRusselo's Guide thread it was there just so u could use it to reboot into cwm recovery and flash a dev rom. Have u tried holding both volume up and down & power buttons together until u see the at&t screen and then releasing the buttons ?? That should boot u into cwm. And from there u can flash a dev rom.
Download mode is--phone off, hold volume down, insert micro usb end of cable into phone, having already opened Odin or Heimdall and usb end of cable already connected to pc. Or of course, jig will do the trick for ya.
U could also try flashin an appropriate kernel for ur firmware u r on --- stock or dev'd. But u will need to still get into download or recovery for that. But i would think u should be able to boot up with no probs with a correct kernel.
Sent from my SGH-I897 using xda premium
4-2ndtwin said:
Depending on what stock rom u were on before that flash of the speedmod kernel, it may not boot ur phone, because i believe it was froyo based. And if u got it from TRusselo's Guide thread it was there just so u could use it to reboot into cwm recovery and flash a dev rom. Have u tried holding both volume up and down & power buttons together until u see the at&t screen and then releasing the buttons ?? That should boot u into cwm. And from there u can flash a dev rom.
Download mode is--phone off, hold volume down, insert micro usb end of cable into phone, having already opened Odin or Heimdall and usb end of cable already connected to pc. Or of course, jig will do the trick for ya.
Sent from my SGH-I897 using xda premium
Click to expand...
Click to collapse
I did manage to get it into download mode. I had the usb cord already connected to the phone when I was holding Volume-, so that was the problem with that. Buuuut, I can't get into CWM at all. Holding Volume+ and Volume- plus the power button loads it directly into the Samsung logo screen, then reboots the phone. Maybe I need to reinstall CWM?
dshams said:
I did manage to get it into download mode. I had the usb cord already connected to the phone when I was holding Volume-, so that was the problem with that. Buuuut, I can't get into CWM at all. Holding Volume+ and Volume- plus the power button loads it directly into the Samsung logo screen, then reboots the phone. Maybe I need to reinstall CWM?
Click to expand...
Click to collapse
You need to flash a different kernel if you wanna get in recovery but at this point, flashing KK4 through Odin seems like a better idea
BWolf56 said:
You need to flash a different kernel if you wanna get in recovery but at this point, flashing KK4 through Odin seems like a better idea
Click to expand...
Click to collapse
I already went ahead and did that, and it's loading back to the regular start screen. Now I'm just trying to get CM10 on there for her, but according to their installation instructions, I need to be able to get into CWM recovery using the 3 button combo, which is where I'm currently stuck. According to one guide I'm reading right now, installing the corn kernel should fix the problem.
dshams said:
I already went ahead and did that, and it's loading back to the regular start screen. Now I'm just trying to get CM10 on there for her, but according to their installation instructions, I need to be able to get into CWM recovery using the 3 button combo, which is where I'm currently stuck. According to one guide I'm reading right now, installing the corn kernel should fix the problem.
Click to expand...
Click to collapse
Yes indeed. Have CM10 on your SD. flash Corn kernel through Odin 1.85, reboot in recovery and flash CM10 as per their instructions.
BWolf56 said:
Yes indeed. Have CM10 on your SD. flash Corn kernel through Odin 1.85, reboot in recovery and flash CM10 as per their instructions.
Click to expand...
Click to collapse
Yeah, still can't get into recovery. I turn off the phone, hold both volume buttons and the power button, but then it just stays at and keeps reloading the samsung loading screen (which now says i9000 instead of sgh-i897 like it did before). If I let go of the power button while on this screen, it progresses through the 3G/ATT screen and finally turns on the phone. Not sure what I need to do now. More research apparently.
dshams said:
Yeah, still can't get into recovery. I turn off the phone, hold both volume buttons and the power button, but then it just stays at and keeps reloading the samsung loading screen (which now says i9000 instead of sgh-i897 like it did before). If I let go of the power button while on this screen, it progresses through the 3G/ATT screen and finally turns on the phone. Not sure what I need to do now. More research apparently.
Click to expand...
Click to collapse
Which KK4 did you flash? With the I897 bootloaders or I9000? And did you flash Corn kernel?
Getting in recovery can be tricky with the button combo. you could use ROM manager to get in recovery if you did flash Corn.
BWolf56 said:
Which KK4 did you flash? With the I897 bootloaders or I9000? And did you flash Corn kernel?
Getting in recovery can be tricky with the button combo. you could use ROM manager to get in recovery if you did flash Corn.
Click to expand...
Click to collapse
Well, I assumed it was the I897 one since the guide I had been using was for that version of the captivate, but I'm going to redownload one so I can be sure. The model number under phone info says "SAMSUNG-SGH-I897" and the kernel version is the "Cornv706" version.
Also, couldn't get into recovery with ROM manager either; it just got stuck at the Samsung screen.
dshams said:
Well, I assumed it was the I897 one since the guide I had been using was for that version of the captivate, but I'm going to redownload one so I can be sure. The model number under phone info says "SAMSUNG-SGH-I897" and the kernel version is the "Cornv706" version.
Also, couldn't get into recovery with ROM manager either; it just got stuck at the Samsung screen.
Click to expand...
Click to collapse
In that case, reflash both stock KK4 and Corn Kernel. Seems like something went wrong.
BWolf56 said:
In that case, reflash both stock KK4 and Corn Kernel. Seems like something went wrong.
Click to expand...
Click to collapse
That's exactly what I did. Finally managed to get to CWM recovery and install CM10 after that. Thanks for all the help Wolf!
dshams said:
That's exactly what I did. Finally managed to get to CWM recovery and install CM10 after that. Thanks for all the help Wolf!
Click to expand...
Click to collapse
Glad I could help! :good:

[Q] SGH-I897 soft bricked?

hey guys, i believe i acquired a soft bricked galaxy s last night. from what the girl told me, it had been rooted, custom rom installed, and im guessing a kernel aswell.it gets past the "world phone" screen then gets stuck at the glowing android coming out of the ground. Im assuming its a kernel problem. ive tried alot of methods on here, searched alot of the forums on these phones being soft bricked. tried the vol+,home, power; vol-,home, power; both volumes, power; also tried with connecting usb and odin open; both volumes, connect usb, input batt; vol-, connect usb, input batt; ectect. i just cant get past that boot logo. I have the drivers from samsung installed but when connecting to the computer it registers that something connected but doesnt identify the phone. so is there anything i am missing guys? i read about the jig and i am guessing thats where im gonna have to go with this. no problem there; just seeing if anyone has any other ideas. thanks in advance guys!
coltlacey1 said:
hey guys, i believe i acquired a soft bricked galaxy s last night. from what the girl told me, it had been rooted, custom rom installed, and im guessing a kernel aswell.it gets past the "world phone" screen then gets stuck at the glowing android coming out of the ground. Im assuming its a kernel problem. ive tried alot of methods on here, searched alot of the forums on these phones being soft bricked. tried the vol+,home, power; vol-,home, power; both volumes, power; also tried with connecting usb and odin open; both volumes, connect usb, input batt; vol-, connect usb, input batt; ectect. i just cant get past that boot logo. I have the drivers from samsung installed but when connecting to the computer it registers that something connected but doesnt identify the phone. so is there anything i am missing guys? i read about the jig and i am guessing thats where im gonna have to go with this. no problem there; just seeing if anyone has any other ideas. thanks in advance guys!
Click to expand...
Click to collapse
A jig will force download mode but is only needed is vol down + power button doesn't get you in it.
Do you know if she was on gb and up? That would change your button combo to get in recovery to vol up + down + power button.
If you can get in recovery that way, you have 2 options: 1- clear cache and dalvik (in advanced) and try rebooting. 2- reflash the custom ROM she was running (without deleting anything).
If recovery doesn't work, get in download mode and flash Odin KK4 without bootloaders (in dev section). From there, you'll need to flash Corn kernel with Odin 1.85 and you'll be able to get in recovery to flash the ROM and Gapps she was running. *Doing this will wipe her apps and apps data*
Sent from my SGH-I897 using xda app-developers app
BWolf56 said:
A jig will force download mode but is only needed is vol down + power button doesn't get you in it.
Do you know if she was on gb and up? That would change your button combo to get in recovery to vol up + down + power button.
If you can get in recovery that way, you have 2 options: 1- clear cache and dalvik (in advanced) and try rebooting. 2- reflash the custom ROM she was running (without deleting anything).
If recovery doesn't work, get in download mode and flash Odin KK4 without bootloaders (in dev section). From there, you'll need to flash Corn kernel with Odin 1.85 and you'll be able to get in recovery to flash the ROM and Gapps she was running. *Doing this will wipe her apps and apps data*
Sent from my SGH-I897 using xda app-developers app
Click to expand...
Click to collapse
yea, whatever happens to the phone doesnt matter, its mine now, was just given to me. sadly idk what rom she was running, her sd card is MIA, and idk what OS she was running on. i highly doubt she would even know. so at this point after trying all the button combos, think a jig is the only option?
What happens if u pull the battery, replace it, leave phone off, phone must be off, connect usb end of cable to ur pc, hold both volume up and down together and then insert micro usb into phone ??
Download mode yes or no ?
If no see my sig below (if ur on a pc or in a web browser)...there are links there on how to make a Jig and/or where to buy a Jig.
Sent from my SGH-I777 using xda premium
4-2ndtwin said:
What happens if u pull the battery, replace it, leave phone off, phone must be off, connect usb end of cable to ur pc, hold both volume up and down together and then insert micro usb into phone ??
Download mode yes or no ?
If no see my sig below (if ur on a pc or in a web browser)...there are links there on how to make a Jig and/or where to buy a Jig.
Sent from my SGH-I777 using xda premium
Click to expand...
Click to collapse
Same story man. Probably gonna be jig is what it is looking like. Any ideas what cause this to happen? Ex. Not being able to enter recovery/download by using proper button combos?
Just a known issue on some Capivates. But the flash up to GB firmware is the fix for the button combos failin to work. Once u have the GB BLs ur button combos should work.
So once u get a jig, Odin or Heimdall up to KK4 with Bootloaders (heed all warnings about flashin BLs). Then u can Odin KK4 Corn Kernel and proceed where u wish.
Sent from my SGH-I777 using xda premium
Thanks for responding. I'll probably tear into it tomorrow. Have a link to kk4 w/boot have thee corn kernel saved
Here is Stock KK4....http://forum.xda-developers.com/showthread.php?p=18370912
Sent from my SGH-I777 using xda premium
Beauty! So that should wake it up. And from there I can reboot, find out what is it has then flash a new ROM after making sure recovery works and whatnot?
After the Stock kk4 flash it will have....Stock i897ucKK4 Gingerbread 2.3.5 Firmware.
So afterwards u will need to use Odin to flash the .tar file version of the KK4 Corn Kernel in order to get cwm recovery and go from there in the flashin of dev roms if u want.
Sent from my SGH-I777 using xda premium
4-2ndtwin said:
After the Stock kk4 flash it will have....Stock i897ucKK4 Gingerbread 2.3.5 Firmware.
So afterwards u will need to use Odin to flash the .tar file version of the KK4 Corn Kernel in order to get cwm recovery and go from there in the flashin of dev roms if u want.
Sent from my SGH-I777 using xda premium
Click to expand...
Click to collapse
Little precision: Odin one click is what you'll be using to flash KK4 (stock gb firmware). Odin 1.85 is what you'll need to flash Corn kernel (.tar is PDA slot).
Sounds great. Should be able to get it done today
well i built a jig using the three resistors from radioshack and a micro usb cable i found laying around. doesnt appear to be working...
ok, so i needed an actual samsung cord......plugged it into my computer and it started charging
ok, got it! now searching for correct drivers. apparently i had the wrong ones
coltlacey1 said:
ok, got it! now searching for correct drivers. apparently i had the wrong ones
Click to expand...
Click to collapse
See this post....http://forum.xda-developers.com/showthread.php?p=33279682.
And that thread may prove helpful to ya. :thumbup:
Sent from my SGH-I777 using xda premium
downloading the stock kk4 now. ok, so what about the root it had? doesnt this dispose of root? or will it still be rooted? and is there anything in particular in odin i need the check mark before flashing the two files?
well ok so the file should tell me what i need to do. says it has instructions
do i have to root to install?
coltlacey1 said:
do i have to root to install?
Click to expand...
Click to collapse
Nope...The KK4 one click has instructions included. :thumbup:
After the successful flash of the KK4 one click, just use this...it will get u Root and KK4 Corn Kernel v7.0A so that u can have CWM Recovery....[Utility]KK4 Easy Root
Sent from my SGH-I777 using xda premium

Categories

Resources