wrong firmware on i9000 - Galaxy S I9000 Q&A, Help & Troubleshooting

I accidentally installed a capitvate i897 firmware (Android 2.3.4, AT&T branded) on my i9000. It looks like an US firmware, mine should be German.
Since installation of the new firmware I can't use the usb-connection anymore - some seconds after plugging the phone resets and stops working until I unplug the cable again. The 3-button-trick doesn't work anymore either, probably because the captivate hardware is quite different.
So... now I am desparately looking for any help or hints how I can get my phone rootet. I think that would help a lot to install a proper firmware again (via mobile odin).
Any hints?

Gingerly said:
I accidentally installed a capitvate i897 firmware (Android 2.3.4, AT&T branded) on my i9000. It looks like an US firmware, mine should be German.
Since installation of the new firmware I can't use the usb-connection anymore - some seconds after plugging the phone resets and stops working until I unplug the cable again. The 3-button-trick doesn't work anymore either, probably because the captivate hardware is quite different.
So... now I am desparately looking for any help or hints how I can get my phone rootet. I think that would help a lot to install a proper firmware again (via mobile odin).
Any hints?
Click to expand...
Click to collapse
You wouldn't really be going wrong by flashing back with Odin. I'd recommend flashing stock JW4 which is the latest European Gingerbread and rooting with the JW4 CF-ROOT.

I would have flashed already if I knew how to do it USB doesn't work, and entering recovery mode (if it is available, which I doubt) doesn't work either because I can't press the right buttons.

Gingerly said:
I would have flashed already if I knew how to do it USB doesn't work, and entering recovery mode (if it is available, which I doubt) doesn't work either because I can't press the right buttons.
Click to expand...
Click to collapse
u need to download 3 file odin from here http://www.hotfile.com/dl/150483619/708026d/I9000XXJW4_I9000OXAJW4_XEU.zip.html
and u will need also odin program from here http://www.filecrop.com/Odin-1.85.html after u download the firmware extract it and open odin
then put code in pda box modem on phone box an csc on csc box after that push vol down+home+power for download mode conect your phone to the computer and wait for yellow light in the program after thet press start good. luck btw if its only one file firmware put it on pda only
and if download mode not work with 3 button comb try jig device

Thanks for your detailed answer. But the 3-button-combo doesn't work. My guess is that the phone expects the captivate combo (volume up + volume down + power) which isn't possible on an i9000 device.
A jig might be worth a try, though I am worried, because the phone crashes always as soon as it get's power via usb (phone-pc or phone-power suppy, in both cases the phone crashes).
Is it possible to root the phone via wifi or right on the phone via app or some weird linux command line stuff?

You could try z4root? I don't think it will work but worth a try
Sent from my GT-I9000 running remICS-UX using XDA premium

Gingerly said:
Thanks for your detailed answer. But the 3-button-combo doesn't work. My guess is that the phone expects the captivate combo (volume up + volume down + power) which isn't possible on an i9000 device.
A jig might be worth a try, though I am worried, because the phone crashes always as soon as it get's power via usb (phone-pc or phone-power suppy, in both cases the phone crashes).
Is it possible to root the phone via wifi or right on the phone via app or some weird linux command line stuff?
Click to expand...
Click to collapse
Yes, I think it's worth a try, to download a SGS Kernel and try the App "SGS Kernel Flasher" (Search in Playstore, can't post a link) Maybe it works! I think you won't be able to boot your system after that, but maybe you can use the 3 button combo after that.
But first you have to find a way to root the phone... i can't find a app for that atm, maybe someone else found one?
------------------------------------------------------------------------------
EDIT
------------------------------------------------------------------------------
If you get root working, you can safely use this to flash the right firmware for your phone: http://forum.xda-developers.com/showthread.php?t=1347899
It's Odin on your mobile, so you can copy the files via an ftp or something like this and flash them to solve ur problem.
The other method I listed is a bit unsafe i think...

Actually, you can press Volume Up and Volume Down at the same time on a SGS. I tried it, because CM9 has the feature to change ringer mode this way.

nahum05 said:
u need to download 3 file odin from here http://www.hotfile.com/dl/150483619/708026d/I9000XXJW4_I9000OXAJW4_XEU.zip.html
and u will need also odin program from here http://www.filecrop.com/Odin-1.85.html after u download the firmware extract it and open odin
then put code in pda box modem on phone box an csc on csc box after that push vol down+home+power for download mode conect your phone to the computer and wait for yellow light in the program after thet press start good. luck btw if its only one file firmware put it on pda only
and if download mode not work with 3 button comb try jig device
Click to expand...
Click to collapse
Hello, More or less had the same problem.
To tell you the history: updated my samsung galaxy S I9000 to ICS, was not happy with it and f*cked up after that.
Wanted to install older firmware over ICS, telephone dead and than came on this forum and used
stockrom of I896 from developer TRusselo : http://forum.xda-developers.com/showthread.php?t=979133
now phone thinks he is a canadian I896.... Tried the above steps on PDA... unpacked ok but now phone keeps rebooting after it shows the samsunglogo....
did i miss a final step or did i do something wrong?
Thanks for your help in advance...

@calumn96: I tried z4root, it doesn't work..
@coroner21: wow! I always thought the both volume buttons would exclude each other. Now I can enter CWM.
Is there a way to root the i9000 in CWM? Or even better, to install a stock i9000 firmware?
Current situation: i897-firmware (2.3.4 uckh3) - I guess I need a root patch for this firmware.

Gingerly said:
@calumn96: I tried z4root, it doesn't work..
@coroner21: wow! I always thought the both volume buttons would exclude each other. Now I can enter CWM.
Is there a way to root the i9000 in CWM? Or even better, to install a stock i9000 firmware?
Current situation: i897-firmware (2.3.4 uckh3) - I guess I need a root patch for this firmware.
Click to expand...
Click to collapse
If you get a rooted i879 kernal you could try flashing that in cwm? You could try flashing a custom gb ROM from it (put files on a as card then in phone so not to use USB)
Sent from my GT-I9000 running remICS-UX using XDA premium

Gingerly said:
@calumn96: I tried z4root, it doesn't work..
@coroner21: wow! I always thought the both volume buttons would exclude each other. Now I can enter CWM.
Is there a way to root the i9000 in CWM? Or even better, to install a stock i9000 firmware?
Current situation: i897-firmware (2.3.4 uckh3) - I guess I need a root patch for this firmware.
Click to expand...
Click to collapse
Go into download mode
for i9000 it's volume down + home + power
for i897 it's both volume keys, and with the usb cable into the phone + power.
If you see the yellow triangle with and android and a shovel that's it!
Then get a stock firmware for i9000 on www.smafirmware.com and flash it through odin with the .pit + 3 files (PDA + MODEM + CSC).

@calum96: I will give it a try.
@-m3ta- : USB doesn't work, so any tips involving a usb-cable won't help :/
Another thing I realized is that recharging is barely possible...

Odin and Samfirmware is the way to go
Sent from my GT-I9300 using Tapatalk 2

Gingerly said:
@calum96: I will give it a try.
@-m3ta- : USB doesn't work, so any tips involving a usb-cable won't help :/
Another thing I realized is that recharging is barely possible...
Click to expand...
Click to collapse
I don't understand why 3 combo key, USB won't work. I had flash a captivate firmware onto the i9000 and the regular trick worked

@MrAndroid12: I don't understand it either. But the phone crashes as soon as the usb is plugged. Recharging didn't work at all, the phone just got hot and that's it.
@calum96: thank you! I flashed dmore 3.3 and so far it looks good. No usb-crashes anymore and the phone acts as it should. There is still an AT&T-brand, but that's still better than a useless phone

Gingerly said:
@MrAndroid12: I don't understand it either. But the phone crashes as soon as the usb is plugged. Recharging didn't work at all, the phone just got hot and that's it.
@calum96: thank you! I flashed dmore 3.3 and so far it looks good. No usb-crashes anymore and the phone acts as it should. There is still an AT&T-brand, but that's still better than a useless phone
Click to expand...
Click to collapse
You might be able to change the brands thing in build.props? Not sure tbh

So is it on i9000 firmware now? or is it just rooted? And is USB working now?
Sent from my GT-I9000 running remICS-UX using XDA premium

Everything works like a charm now
i9000 firmware (slim ics right now), usb works, recharging works and people can finally call me again (didn't work before either)
Thanks again for all your help, guys!

Glad to hear try remics its really good smooth with a Samsung feel
Sent from my GT-I9000 running remICS-UX using XDA premium

Related

[Q] In need of desperate help

Hi!
After showing my mate my desire which has been rooted he asked me if id do his Galaxy S.
after following the guide here http://forum.xda-developers.com/showthread.php?t=728754
I rebooted and got stuck in a boot loop. It stays at the Samsung Galaxy S screen and doesnt go any further!
Ive had to take his phone home to fix it!
Can you offer any advice on how to get it going again?
Thanks in advance,
Andy!.
delete cache and dalvik from home+power+volume up.
should boot fine after that.
Sent from my GT-I9000 using XDA App
Thanks, Yeah ive tried that still stays at Galaxy S screen forever....
Download Odin and an apropriate flashfile and flash the phone.
Before you start take out the sim card and memory card.
Every info on how to flash via Odin is in this forum, just search.
After that root your friends phone.
I've atached the files for rooting only on Eclair 2.1.
Robi-K said:
Download Odin and an apropriate flashfile and flash the phone.
Before you start take out the sim card and memory card.
Every info on how to flash via Odin is in this forum, just search.
After that root your friends phone.
I've atached the files for rooting only on Eclair 2.1.
Click to expand...
Click to collapse
Thanks alot will try that!!
Andyokane said:
Thanks alot will try that!!
Click to expand...
Click to collapse
ok I really am ****ting myself now!! I downloaded odin and flashed it with
[ROM] Tayutama Edition v1.1 [I9000XWJM8] 17/9/2010
Now im stuck at an AT&T boot loop!!!!
Have I flashed a wrong file??? have a bricked it??
did you odin jm8 before flashing tayutamas rom? tayutama rom is a mod, it depends on jm8 and can not be flashed with odin but needs to be installed via update.zip through recovery console
FadeFx said:
did you odin jm8 before flashing tayutamas rom? tayutama rom is a mod, it depends on jm8 and can not be flashed with odin but needs to be installed via update.zip through recovery console
Click to expand...
Click to collapse
hi, yeah I did flash the latest firmware before flashing the rom...
I feel sick...
Andyokane said:
hi, yeah I did flash the latest firmware before flashing the rom...
I feel sick...
Click to expand...
Click to collapse
Did you flash Tayutama's ROM using Odin? Or did you use the update.zip method?
Well, here's all the steps you need to follow in detail:
1) Flash JM8 using Odin (follow flashing guide from Richtofen's thread).
2) Download Tayutama's JM8 ROM, rename the zip file to "update.zip" and put it on /sdcard. So it looks like /sdcard/update.zip. Turn off the phone. Get into recovery mode (volume up + home + power). Choose the option "Apply from sdcard: update.zip" or whatever. (NOTE: Don't flash this using Odin).
That's it. BTW, you lost all data on your mate's phone when you flashed JM8 onto it. Hope he isn't too mad.
ed10000 said:
Did you flash Tayutama's ROM using Odin? Or did you use the update.zip method?
Well, here's all the steps you need to follow in detail:
1) Flash JM8 using Odin (follow flashing guide from Richtofen's thread).
2) Download Tayutama's JM8 ROM, rename the zip file to "update.zip" and put it on /sdcard. So it looks like /sdcard/update.zip. Turn off the phone. Get into recovery mode (volume up + home + power). Choose the option "Apply from sdcard: update.zip" or whatever. (NOTE: Don't flash this using Odin).
That's it. BTW, you lost all data on your mate's phone when you flashed JM8 onto it. Hope he isn't too mad.
Click to expand...
Click to collapse
I cant flash anything cos I cant get it in to recovery or download mode...
Andyokane said:
I cant flash anything cos I cant get it in to recovery or download mode...
Click to expand...
Click to collapse
Why not? You were able to do it before right? What happens if you try now?
EDIT: Wait, is it the international version of the Galaxy S (I9000) or the AT&T Vibrant (T959) AT&T Captivate I897?
Hold on just for a little while longer.
As long as the phone goes into recovery you havn't bricked it yet.
Go here and register and download a stock (non moded) firmware:
samfirmware.com
I recomend XXJM1 as that was the most stable for me until now, but other will do.
First wipe cache and format phone.
Then flash the stock firmware with repartition checked with Odin.
Then root the phone.
I've attached Odin and a text file explaining where to put each file.
Good luck.
I Can't get into recovery mode, the 3 button trick doesn't work. Im just stuck at the At&t screen, goes black and then back the at&t.
I think It's buggered.
It's a UK orange i9000 Samsung galaxy S.
Sent from my HTC Desire using XDA App
Andyokane said:
I Can't get into recovery mode, the 3 button trick doesn't work. Im just stuck at the At&t screen, goes black and then back the at&t.
I think It's buggered.
It's a UK orange i9000 Samsung galaxy S.
Sent from my HTC Desire using XDA App
Click to expand...
Click to collapse
Why is there a AT&T screen on a UK Orange I9000?
The 3-button trick has never worked on that phone or stopped working after the bad flashes? (coz I read in one of your posts that you tried getting into recovery mode and deleting cache/data?)
Yes the 3 button thing did work before just not now.
I didn't know it was at&t until I had flashes it, I just downloaded it from the development section.
Sent from my HTC Desire using XDA App
I still cant figure out what you did wrong
did you flash a vibrant rom? i think there was a guy having the same problem some time ago here...
http://forum.xda-developers.com/showthread.php?t=782920
Please try all of these in the same order and see if anything gets the phone into Download Mode successfully.
Start with the phone turned off (remove and insert battery if necessary)
Method 1:
a) Hold down vol up + vol down.
b) While still holding down both the volume buttons, press and hold the power button.
Method 2:
a) Hold down vol up + vol down.
b) Plug in the USB cable to your computer while still holding down both the volume buttons.
Method 3:
a) Hold down only the vol down button.
b) Plug in the USB cable to your computer while still holding down the vol down button.
Don't even touch the power button in methods 2 and 3.
EDIT: Make sure the drivers are installed in the computer first. If you don't have the drivers, installing Kies would automatically install the required drivers for you. While trying these methods (connecting USB cable to computer), though, make sure Kies is completely closed (even from the system tray) and keep Odin open.
Hi Thanks for the info. Tried all your ideas and still nothing. My pc isn't recognising the phone anymore.
Sent from my HTC Desire using XDA App
I guess there's nothing more I can do then. Gonna have to let him know what's happened.
Sent from my HTC Desire using XDA App

[Q] Rooting galaxy s with gingerbread 2.3.3

I can't root my sgs, i have tryed almost every tutorials i can find about this, but i can't connect to odin when the phone is in download mode. I even get this up in download mode: can't access to '/system/csc/xee/system/' Anyone that can help me with this issue?
Uh... sounds like something is seriously wrong with your phone dude =\ You should be able to get to d/l mode regardless. Does the phone still work fine otherwise?
Unable to root sgs gingerbread NEJVD
I have the same problem after upgrading to official firmware via kieys. Running PDA:I9000NEJVD, PHONE:I9000NEJV5, CSC:H3GJV6 on 3mobile. Odin doesn't recognise phone in download mode, computer only reads onboard sd card when connected as usb storage. Tried one superoneclick too but stops at running pnueter exploit/gingerbreak exploit. Super laggy as well, Can i roll back to froyo? any help highly appreciated.
samgal111 said:
I have the same problem after upgrading to official firmware via kieys. Running PDA:I9000NEJVD, PHONE:I9000NEJV5, CSC:H3GJV6 on 3mobile. Odin doesn't recognise phone in download mode, computer only reads onboard sd card when connected as usb storage. Tried one superoneclick too but stops at running pnueter exploit/gingerbreak exploit. Super laggy as well, Can i roll back to froyo? any help highly appreciated.
Click to expand...
Click to collapse
Did you try diffrent usb port on your cpu?
also..on the cpu that your using odin to flash , do you have kies installed?
if so make sure it isn't running ( i would uninstall just incase)
see if that helps.
Sent from my i9000t XDA app
I am interested in rooting too, and I have gingerbread. I have 2 problems though, first, I do not have the 3button combo working. I thought the gingerbread update would fix it, but no luck, and the method I found here did not work. I hear that you should not try to root without the 3 button combo working, but what choice do I have, samsung update did not fix this bootloader problem. I cannot put my phone in download mode without having it plugged in and recognized by adb.
My 2nd problem is that I have a I9000T and it seems nobody has this phone around here so I have no way of knowing if some of the rooting options even work for my phoen and firmeware.
Any help would be greatly appreciated.
caribbean_spur said:
I am interested in rooting too, and I have gingerbread. I have 2 problems though, first, I do not have the 3button combo working. I thought the gingerbread update would fix it, but no luck, and the method I found here did not work. I hear that you should not try to root without the 3 button combo working, but what choice do I have, samsung update did not fix this bootloader problem. I cannot put my phone in download mode without having it plugged in and recognized by adb.
My 2nd problem is that I have a I9000T and it seems nobody has this phone around here so I have no way of knowing if some of the rooting options even work for my phoen and firmeware.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
I actually have a i9000t, ive soft bricked a few times as long as you could get into download mode you should be ok, allways keep a stock rom around just incase to flash back to through odin.
Ive flashed a few modem with no problems, few roms with minimal problems..
Cm7 lost radio and weird pixle screen boot.
Deoxidized roms work good.
I had flashed Darkys 9.5 and everything worked till i noticed the stock music player gave me reboots.
I had tried flashing MIUI but no luck at all, could of been my zip. File was messed up but i tried a diffrent and still nothing.Now im on Darky 10.1 final no problems.
This has to be the most stable/fastest rom ive ever flashed.
Edit i looked up something that might help.. http://forum.xda-developers.com/showthread.php?t=723596
Sent from my i9000T XDA premium app
afalk said:
I can't root my sgs, i have tryed almost every tutorials i can find about this, but i can't connect to odin when the phone is in download mode. I even get this up in download mode: can't access to '/system/csc/xee/system/' Anyone that can help me with this issue?
Click to expand...
Click to collapse
hi.. do you have official kies installed on your computer?
if so uninstall it first... and installed the unofficial samsung driver.. sorry i cant post link here as am junior member..
you can search in google "samsung usb.rar". Once you download it, then installed it on your computer. Open you odin, put your phone in download mode,
and plug in to computer, then odin should be able to recognize your phone.
Once I have the same problem and it works for me with above step. hope that help.
Dorilife said:
I actually have a i9000t, ive soft bricked a few times as long as you could get into download mode you should be ok, allways keep a stock rom around just incase to flash back to through odin.
Ive flashed a few modem with no problems, few roms with minimal problems..
Cm7 lost radio and weird pixle screen boot.
Deoxidized roms work good.
I had flashed Darkys 9.5 and everything worked till i noticed the stock music player gave me reboots.
I had tried flashing MIUI but no luck at all, could of been my zip. File was messed up but i tried a diffrent and still nothing.Now im on Darky 10.1 final no problems.
This has to be the most stable/fastest rom ive ever flashed.
Edit i looked up something that might help.. http://forum.xda-developers.com/showthread.php?t=723596
Sent from my i9000T XDA premium app
Click to expand...
Click to collapse
Thanks for the reply! Ok, I finally manage to have the 3button combo work and get into download mode and recovery mode. I want to root, can you tell me if the odin method works on 2.3.3 stock, on I9000T . Also, How can I fully backup my phone. Which android version did you have when you rooted.
Also, I keep reading those very old threads and I was wondering what the latest Odin version is used for 2.3.3.
elita said:
hi.. do you have official kies installed on your computer?
if so uninstall it first... and installed the unofficial samsung driver.. sorry i cant post link here as am junior member..
you can search in google "samsung usb.rar". Once you download it, then installed it on your computer. Open you odin, put your phone in download mode,
and plug in to computer, then odin should be able to recognize your phone.
Once I have the same problem and it works for me with above step. hope that help.
Click to expand...
Click to collapse
Tried this workaround, but still no luck with Odin. When fone is in download mode, I get the message apling multi-csc...Installing multi-csc then "unable to access system/csc/H3G/system/".Couldnt roll back the os through kies either before I uninstalled it. Any help highly appreciated
Would definitely would like to know how to root 2.3.3 (UBJV6)? Is there anything specia; I have to do since I have recovery 3e too?
Any help will be welcome!
Wrong button combo
caribbean_spur said:
Would definitely would like to know how to root 2.3.3 (UBJV6)? Is there anything specia; I have to do since I have recovery 3e too?
Any help will be welcome!
Click to expand...
Click to collapse
Turns out We/I have been using the wrong button combo for download. Download mode is: Vol DOWN+Home+Power On.!!! Recovery mode is Vol UP+Home+Power On. I used Fuguroot with my stock kernel from RAMAD (senior developer). Flashed with odin & it took LESS THAN 2 MIN! Check out this link here http://forum.xda-developers.com/showthread.php?t=1011901.Hope this helps. Do remember to thank Ramad and Nicademus!
good you figured out
Hi, I did something stupid... I been trying to upload gingerbread to my Galaxy Tab. and I used re-partition.. so now I bricked.. It starts with samsug logo and after stops showing only the samsung galaxy..
Please Help me...
Thanks Guys
rrubio999 said:
Hi, I did something stupid... I been trying to upload gingerbread to my Galaxy Tab. and I used re-partition.. so now I bricked.. It starts with samsug logo and after stops showing only the samsung galaxy..
Please Help me...
Thanks Guys
Click to expand...
Click to collapse
I don't have a galaxy tab, but it should be similliar to my galaxy s. I think your device is NOT bricked. As long as you can get to download mode, your device is NOT bricked. If you can get there, you should try to flash with odin/heimdall again. I think you must have done something wrong in the flashing process. AFAIK the logo is displayed by bootloader (primary), so if nothing went wrong with flashing the secondary one (download mode), you should be able to flash again.

Bricked Captivate?!?!?

Hi, I was using ODIN3 JF6 for porting my 2.2 to 2.1 eclair rom.. once the flashing done with no problem it gives me Reset phone.. then the phone reset it only shows me At&T logo continuosly again and again.. I tried to get on download mode in all ways but nothing.. adb doesn't recognize the phone and no com port on odin .... is it defintely bricked?????
early81 said:
Hi, I was using ODIN3 JF6 for porting my 2.2 to 2.1 eclair rom.. once the flashing done with no problem it gives me Reset phone.. then the phone reset it only shows me At&T logo continuosly again and again.. I tried to get on download mode in all ways but nothing.. adb doesn't recognize the phone and no com port on odin .... is it defintely bricked?????
Click to expand...
Click to collapse
If you can see a screen, it's not bricked. For download mode, did you try (from a powered-off state) holding Vol+ and Vol-, then inserting the USB plug? You may also have to take the battery out, hold v+/v-, insert plug, then insert battery.
If those don't work, look into getting yourself a jig.
jmtheiss said:
If you can see a screen, it's not bricked. For download mode, did you try (from a powered-off state) holding Vol+ and Vol-, then inserting the USB plug? You may also have to take the battery out, hold v+/v-, insert plug, then insert battery.
If those don't work, look into getting yourself a jig.
Click to expand...
Click to collapse
yes i get the AT&T logo infinite looping but no way to get download mode.. yes I even tried the vol+vol- ...
If those combinations aren't working for you, you will most likely need to either buy or make yourself a jig. It's not very expensive - either buy 3 resistors at an electronics store, or see if you can find one on Ebay. That's the easiest, most surefire way to get into download mode.
One last thing to try, though, just in case - try holding Vol- and Power from a powered-off state. That's the Gingerbread combination for i9000 bootloaders, but it won't hurt to try them.
jmtheiss said:
If those combinations aren't working for you, you will most likely need to either buy or make yourself a jig. It's not very expensive - either buy 3 resistors at an electronics store, or see if you can find one on Ebay. That's the easiest, most surefire way to get into download mode.
One last thing to try, though, just in case - try holding Vol- and Power from a powered-off state. That's the Gingerbread combination for i9000 bootloaders, but it won't hurt to try them.
Click to expand...
Click to collapse
no way I tried all combinations many times ..no way to get download mode.. i will keep on ebay the jig..many thanks ..i iwll let know in post if I ll solve this
Once you get into download mode, don't flash jf6 newer phones don't like that firmware and they do exactly what your's is doing. Bootloop and broken button combos.
Flash any other firmware other than jf6 and you'll be good.
studacris said:
Once you get into download mode, don't flash jf6 newer phones don't like that firmware and they do exactly what your's is doing. Bootloop and broken button combos.
Flash any other firmware other than jf6 and you'll be good.
Click to expand...
Click to collapse
where can I get a new firmware with Odin??.. I supposed the odin JF6 was the best for resuming 2.1 stock firmware.. can you please post me a link on xda of a similar odni firmware?
I used JF6 only beacuse on the forum it said that is the best for installing the i9000 bootloader and kernel... thanks
Here ya go... [Stock ROMs](OneClicks Master Collection)+[Kernels (Stock & w/ CWM)]+[Modems] UPDATED ---- These are all i897 firmwares, some with the choice of i897 GB Bootloaders included and some without.
ok I get the jig.. finally I get the download mode ,, I 'm trying to install the 2.3.3 kernel +bootloader UCKF1 is this ok?
thanks
early81 said:
ok I get the jig.. finally I get the download mode ,, I 'm trying to install the 2.3.3 kernel +bootloader UCKF1 is this ok?
thanks
Click to expand...
Click to collapse
That should work, as you're installing a Gingerbread Rom, you'll need the matching bootloaders.
Just make sure you have a good connection to your computer, and that your computer won't lose power in the process.
jmtheiss said:
That should work, as you're installing a Gingerbread Rom, you'll need the matching bootloaders.
Just make sure you have a good connection to your computer, and that your computer won't lose power in the process.
Click to expand...
Click to collapse
Hi, thank you all ,, all worked 100% .. one more thing.. why the bootloader is not the i9000 bootloader ? if I want to install the cm7 can I just install from market the rom manager?? .. and about the root+busybox .. does the super-one click works with 2.3.3 ?
early81 said:
Hi, thank you all ,, all worked 100% .. one more thing.. why the bootloader is not the i9000 bootloader ? if I want to install the cm7 can I just install from market the rom manager?? .. and about the root+busybox .. does the super-one click works with 2.3.3 ?
Click to expand...
Click to collapse
Glad to hear it worked.
- UCKF1 uses the AT&T Gingerbread bootloaders, not the i9000. You have the option to flash the i9000 ones separately, but I wouldn't recommend it, as there really isn't a pressing reason to put yourself in that danger.
- If you want to try CM7 again, I would recommend installing it separately from Rom manager - rom manager tends to be problematic.
- I don't think super one-click works with 2.3.x roms. You'll need to flash a kernel with CWM baked in (like boog's kernel) using Odin or Heimdall, then flash CM7.
- I don't think super one-click works with 2.3.x roms. You'll need to flash a kernel with CWM baked in (like boog's kernel) using Odin or Heimdall, then flash CM7.
Click to expand...
Click to collapse
thank you lot for helping me .. if I install directly this one:
With Bootloaders - Link 1 / Link 2 [With CWM Injected Kernel from Boog]
Boog includes recovrey.. so once install this I can get even recovery ready for cm7???
On the page of one-clicks, in this section:
I897UCKH3 Android 2.3.4 Gingerbread
With Bootloaders - Link 1 / Link 2 [With CWM Injected Kernel from Boog]
Heimdall Package, With Bootloaders - Link to thread - by AdamOutler
Without Bootloaders - Link to thread - by 4-2ndtwin [With CWM Injected Kernel from Boog]
Heimdall Package, Without Bootloaders - Link to thread - by jmtheiss [With CWM Injected Kernel from Boog] (Not tested)
Stock Kernel - Link 1 / Link 2
Kernel with CWM - Link to thread - by Boog
Use one of the two that I have left highlighted. If you want to use Odin, use the first one. If you prefer Heimdall, use the second one. Either one will get you to a stock state, with CWM, so that you can flash CM7. And, both will do this without flashing bootloaders. Definitely, no matter what, do not choose a package with bootloaders. You want a package that says "no bootloaders".
Use one of the two that I have left highlighted. If you want to use Odin, use the first one. If you prefer Heimdall, use the second one. Either one will get you to a stock state, with CWM, so that you can flash CM7. And, both will do this without flashing bootloaders. Definitely, no matter what, do not choose a package with bootloaders. You want a package that says "no bootloaders".
Click to expand...
Click to collapse
ok I did all ,,how to enter in recovery mode?? the vol down + power button isn' t working ...
early81 said:
ok I did all ,,how to enter in recovery mode?? the vol down + power button isn' t working ...
Click to expand...
Click to collapse
Recovery on your phone is now holding Vol+/Vol-/Power. Download will be Vol+/Vol- and inserting the USB cable.
jmtheiss said:
Recovery on your phone is now holding Vol+/Vol-/Power. Download will be Vol+/Vol- and inserting the USB cable.
Click to expand...
Click to collapse
... is not working.. it keeps showing me AT&T logo until I leave the power button,, but once i leave it starts normal use..and not recovery..
EDIT : WITH ADB REBOOT RECOVERY IT WORKS , IT GOES IN CWM 4.0.1.5 ,, TRYING TO INSTALL CM7 .. HOPE WILL WORK
You need a jig. I'm guessing your build number higher then 1010.
Sent from my I897 using XDA App
early81 said:
... is not working.. it keeps showing me AT&T logo until I leave the power button,, but once i leave it starts normal use..and not recovery..
EDIT : WITH ADB REBOOT RECOVERY IT WORKS , IT GOES IN CWM 4.0.1.5 ,, TRYING TO INSTALL CM7 .. HOPE WILL WORK
Click to expand...
Click to collapse
That's good to hear. Let us know if you need more help.
Idk what the deal is with 1010 builds, I have a 1012 build and everything works on it, even JF6 Odin one click!
Sent from my SAMSUNG-SGH-I897 using xda premium

Flashed wrong file via Odin!!

I am in serious trouble and need urgent help!!
I own an international Galaxy GT I9000 and recently rooted and afterwards attempted to flash XXJW4 software on the phone. Upon trying this I realised that my model is one of the unlucky ones as you cannot enter download mode via the three-button combo, neither can you enter recovery. Since I have some experience with Android, I used adb commands to reboot the phone into download mode.
Here is where my problem lies...
I flashed the wrong file using Odin. Instead of flashing the JW4_JW4_JW4 file, I flashed a file named XXJW4_Root_AA.tar... Needless to say, this didn't go down well. The phone is in a boot loop now, rebooting at the Samsung logo (not the boot animation). ADB cannot find the device, neither can odin, and no one seems to be able to help... Is the final solution a a USB Jig? I am in South Africa, so finding one here is hell..
Any help or advice would be greatly appreciated!
If you can't get into download mode, USB jig is your best bet.
Sent from my GT-I9000 using xda app-developers app
snapper.fishes said:
If you can't get into download mode, USB jig is your best bet.
Sent from my GT-I9000 using xda app-developers app
Click to expand...
Click to collapse
Okay, I have been reading up on those but I can't seem to find any resistors in my area! Also, if I do manage to get download mode going, will this ensure that my PC will recognize the phone? Odin and my PC recognized the device just fine, but Kies was not functional (before the phone got bricked)
The jig will solve your problems at no time.It saved me!
Sent from my GT-I9000 using Tapatalk 2
Pull the battery, hold the button to download the mod and then plug the battery into the phone, I hit download.
misacek said:
Pull the battery, hold the button to download the mod and then plug the battery into the phone, I hit download.
Click to expand...
Click to collapse
I tried this but it did not work... I flashed the xxjw4 CF Root file over stock Eclair by mistake, is the stock Eclair still there and can it be considered a soft-brick? If so I would like to know which firmware I can flash to fix this. Is xxjw4 an option or must I flash XXJVU first? (I have downloaded both firmwares and their respective CF Root files) Thanks in advance
IbanMaru said:
I tried this but it did not work... I flashed the xxjw4 CF Root file over stock Eclair by mistake, is the stock Eclair still there and can it be considered a soft-brick? If so I would like to know which firmware I can flash to fix this. Is xxjw4 an option or must I flash XXJVU first? (I have downloaded both firmwares and their respective CF Root files) Thanks in advance
Click to expand...
Click to collapse
Just try this solutions may or may not work, but no harm in trying http://forum.xda-developers.com/showpost.php?p=27205737&postcount=4571
three best stock rom XXJVU file, but with pit 512 and re-partition on.
Just find the Galaxy S drivers from somewhere, my computer does this sometimes, have u got windows 7 running on your PC? sometimes my laptop with windows 7 cant find my device, but my one with Windows Vista always manages to find it, try a different PC first. Once you found the device just flash a full stock version, like XXJVT for example, something with the pit., CODE, CSC and Modem file
IbanMaru said:
I am in serious trouble and need urgent help!!
I own an international Galaxy GT I9000 and recently rooted and afterwards attempted to flash XXJW4 software on the phone. Upon trying this I realised that my model is one of the unlucky ones as you cannot enter download mode via the three-button combo, neither can you enter recovery. Since I have some experience with Android, I used adb commands to reboot the phone into download mode.
Here is where my problem lies...
I flashed the wrong file using Odin. Instead of flashing the JW4_JW4_JW4 file, I flashed a file named XXJW4_Root_AA.tar... Needless to say, this didn't go down well. The phone is in a boot loop now, rebooting at the Samsung logo (not the boot animation). ADB cannot find the device, neither can odin, and no one seems to be able to help... Is the final solution a a USB Jig? I am in South Africa, so finding one here is hell..
Any help or advice would be greatly appreciated!
Click to expand...
Click to collapse
Odin does not reformat /data and /cache and /dbdata back to rfs, so the kernel cannot mount it, hence the bootloop. Just do a factory reset from stock recovery and your good to go
AlwaysDroid said:
Odin does not reformat /data and /cache and /dbdata back to rfs, so the kernel cannot mount it, hence the bootloop. Just do a factory reset from stock recovery and your good to go
Click to expand...
Click to collapse
Okay thanks for the info... So because I am not able to do the three button fix do you recommend that I jig the phone, and flash the three button fix, after that enter recovery and do a wipe? No need to flash the new firmware? (Which I do plan to do but only after I can get the phone up and running again with the jig)
If you can't find the resistors, you can buy the jig off ebay for about 2 quid. I know it's expensive for a 1p resistor and a 1p case but how much is your phone worth to you
The jig will definitely sort it.
skezza said:
If you can't find the resistors, you can buy the jig off ebay for about 2 quid. I know it's expensive for a 1p resistor and a 1p case but how much is your phone worth to you
The jig will definitely sort it.
Click to expand...
Click to collapse
True. I am able to make one though as it's simple enough. The question is what do I do once I get into download mode? Three-button fix or the new firmware? Would XXJW4 be good or should I get the XXJVU firmware instead?? Don't want to make another NoOb mistake. I am pretty much golden when dealing with the Motorola stuff!!
IbanMaru said:
True. I am able to make one though as it's simple enough. The question is what do I do once I get into download mode? Three-button fix or the new firmware? Would XXJW4 be good or should I get the XXJVU firmware instead?? Don't want to make another NoOb mistake. I am pretty much golden when dealing with the Motorola stuff!!
Click to expand...
Click to collapse
Odin must flash over stock rom / pda, phone, csc / pit with 512 and re-partition, preferably back to your stock 2.3.4 region.potom cf root-root kernel version of your firmware., Semaphore kernel and stock rom jw4 , 5.6 ..
it helped me
Flash something safe like XXJVU. Do a full flash too. PIT, CSC, PHONE AND PDA. You'll be fine

[Q] SGH-I897 soft bricked?

hey guys, i believe i acquired a soft bricked galaxy s last night. from what the girl told me, it had been rooted, custom rom installed, and im guessing a kernel aswell.it gets past the "world phone" screen then gets stuck at the glowing android coming out of the ground. Im assuming its a kernel problem. ive tried alot of methods on here, searched alot of the forums on these phones being soft bricked. tried the vol+,home, power; vol-,home, power; both volumes, power; also tried with connecting usb and odin open; both volumes, connect usb, input batt; vol-, connect usb, input batt; ectect. i just cant get past that boot logo. I have the drivers from samsung installed but when connecting to the computer it registers that something connected but doesnt identify the phone. so is there anything i am missing guys? i read about the jig and i am guessing thats where im gonna have to go with this. no problem there; just seeing if anyone has any other ideas. thanks in advance guys!
coltlacey1 said:
hey guys, i believe i acquired a soft bricked galaxy s last night. from what the girl told me, it had been rooted, custom rom installed, and im guessing a kernel aswell.it gets past the "world phone" screen then gets stuck at the glowing android coming out of the ground. Im assuming its a kernel problem. ive tried alot of methods on here, searched alot of the forums on these phones being soft bricked. tried the vol+,home, power; vol-,home, power; both volumes, power; also tried with connecting usb and odin open; both volumes, connect usb, input batt; vol-, connect usb, input batt; ectect. i just cant get past that boot logo. I have the drivers from samsung installed but when connecting to the computer it registers that something connected but doesnt identify the phone. so is there anything i am missing guys? i read about the jig and i am guessing thats where im gonna have to go with this. no problem there; just seeing if anyone has any other ideas. thanks in advance guys!
Click to expand...
Click to collapse
A jig will force download mode but is only needed is vol down + power button doesn't get you in it.
Do you know if she was on gb and up? That would change your button combo to get in recovery to vol up + down + power button.
If you can get in recovery that way, you have 2 options: 1- clear cache and dalvik (in advanced) and try rebooting. 2- reflash the custom ROM she was running (without deleting anything).
If recovery doesn't work, get in download mode and flash Odin KK4 without bootloaders (in dev section). From there, you'll need to flash Corn kernel with Odin 1.85 and you'll be able to get in recovery to flash the ROM and Gapps she was running. *Doing this will wipe her apps and apps data*
Sent from my SGH-I897 using xda app-developers app
BWolf56 said:
A jig will force download mode but is only needed is vol down + power button doesn't get you in it.
Do you know if she was on gb and up? That would change your button combo to get in recovery to vol up + down + power button.
If you can get in recovery that way, you have 2 options: 1- clear cache and dalvik (in advanced) and try rebooting. 2- reflash the custom ROM she was running (without deleting anything).
If recovery doesn't work, get in download mode and flash Odin KK4 without bootloaders (in dev section). From there, you'll need to flash Corn kernel with Odin 1.85 and you'll be able to get in recovery to flash the ROM and Gapps she was running. *Doing this will wipe her apps and apps data*
Sent from my SGH-I897 using xda app-developers app
Click to expand...
Click to collapse
yea, whatever happens to the phone doesnt matter, its mine now, was just given to me. sadly idk what rom she was running, her sd card is MIA, and idk what OS she was running on. i highly doubt she would even know. so at this point after trying all the button combos, think a jig is the only option?
What happens if u pull the battery, replace it, leave phone off, phone must be off, connect usb end of cable to ur pc, hold both volume up and down together and then insert micro usb into phone ??
Download mode yes or no ?
If no see my sig below (if ur on a pc or in a web browser)...there are links there on how to make a Jig and/or where to buy a Jig.
Sent from my SGH-I777 using xda premium
4-2ndtwin said:
What happens if u pull the battery, replace it, leave phone off, phone must be off, connect usb end of cable to ur pc, hold both volume up and down together and then insert micro usb into phone ??
Download mode yes or no ?
If no see my sig below (if ur on a pc or in a web browser)...there are links there on how to make a Jig and/or where to buy a Jig.
Sent from my SGH-I777 using xda premium
Click to expand...
Click to collapse
Same story man. Probably gonna be jig is what it is looking like. Any ideas what cause this to happen? Ex. Not being able to enter recovery/download by using proper button combos?
Just a known issue on some Capivates. But the flash up to GB firmware is the fix for the button combos failin to work. Once u have the GB BLs ur button combos should work.
So once u get a jig, Odin or Heimdall up to KK4 with Bootloaders (heed all warnings about flashin BLs). Then u can Odin KK4 Corn Kernel and proceed where u wish.
Sent from my SGH-I777 using xda premium
Thanks for responding. I'll probably tear into it tomorrow. Have a link to kk4 w/boot have thee corn kernel saved
Here is Stock KK4....http://forum.xda-developers.com/showthread.php?p=18370912
Sent from my SGH-I777 using xda premium
Beauty! So that should wake it up. And from there I can reboot, find out what is it has then flash a new ROM after making sure recovery works and whatnot?
After the Stock kk4 flash it will have....Stock i897ucKK4 Gingerbread 2.3.5 Firmware.
So afterwards u will need to use Odin to flash the .tar file version of the KK4 Corn Kernel in order to get cwm recovery and go from there in the flashin of dev roms if u want.
Sent from my SGH-I777 using xda premium
4-2ndtwin said:
After the Stock kk4 flash it will have....Stock i897ucKK4 Gingerbread 2.3.5 Firmware.
So afterwards u will need to use Odin to flash the .tar file version of the KK4 Corn Kernel in order to get cwm recovery and go from there in the flashin of dev roms if u want.
Sent from my SGH-I777 using xda premium
Click to expand...
Click to collapse
Little precision: Odin one click is what you'll be using to flash KK4 (stock gb firmware). Odin 1.85 is what you'll need to flash Corn kernel (.tar is PDA slot).
Sounds great. Should be able to get it done today
well i built a jig using the three resistors from radioshack and a micro usb cable i found laying around. doesnt appear to be working...
ok, so i needed an actual samsung cord......plugged it into my computer and it started charging
ok, got it! now searching for correct drivers. apparently i had the wrong ones
coltlacey1 said:
ok, got it! now searching for correct drivers. apparently i had the wrong ones
Click to expand...
Click to collapse
See this post....http://forum.xda-developers.com/showthread.php?p=33279682.
And that thread may prove helpful to ya. :thumbup:
Sent from my SGH-I777 using xda premium
downloading the stock kk4 now. ok, so what about the root it had? doesnt this dispose of root? or will it still be rooted? and is there anything in particular in odin i need the check mark before flashing the two files?
well ok so the file should tell me what i need to do. says it has instructions
do i have to root to install?
coltlacey1 said:
do i have to root to install?
Click to expand...
Click to collapse
Nope...The KK4 one click has instructions included. :thumbup:
After the successful flash of the KK4 one click, just use this...it will get u Root and KK4 Corn Kernel v7.0A so that u can have CWM Recovery....[Utility]KK4 Easy Root
Sent from my SGH-I777 using xda premium

Categories

Resources