My computer crashed while trying to flash an SGS I9000 through Odin. The phone will not boot at all - the screen just stays off. I've tried pulling the battery for extended periods but it makes no difference. I can't get into recovery mode or download mode. The screen seems permanently off.
When I put the battery in and plug the phone into the computer it tries (and fails) to install a driver for a "SEC S59C110 Test B/D".
I've tried the 301K resistor jig but it did not seem to do anything.
Any ideas on what I can do? The phone is long out of warranty, so if the phone is permanently dead then I'll just have to buy a new one (though I'm hoping for a fix, if possible!)
You could try this:
http://forum.xda-developers.com/showthread.php?t=1330491
Sent from my GT-I9000 using XDA Premium App
read this too..
it's basically the same thing, but it talks about the possibility of using the unbrickable mod without doing the hardware mod... (if i got it right) wich i think it is your case because the computer is able to enumerate usb.
http://www.xda-developers.com/android/explaining-and-advancing-the-unbrickable-mod/
good luck!
and let us know
interesting, keep us updated if you try unbrickable
Ozzah said:
..........I've tried the 301K resistor jig but it did not seem to do anything.........
Any ideas on what I can do? The phone is long out of warranty, so if the phone is permanently dead then I'll just have to buy a new one (though I'm hoping for a fix, if possible!)
Click to expand...
Click to collapse
It's very strange that the jig fails on these situation.
Maybe that the jig is not correctly built....
Why don't you try with another usb dongle?
I hope that you solve your problem.
I can't believe it - I'm absolutely astounded. UnBrickable and Heimdall worked and they brought the phone back to life! Thank you guys so much!
you did the hardware mod for unbrickable?
No, I dismantled the phone and when I saw how tiny the resistors were I shat my pants.
I tried it without doing the hardware mods first, and I was going to mod it only if it failed (which, fortunately, it didn't!)
you lucky one then if the bootloader would be f.... up you would have to techmod
but anyways gg ;]
Related
Im retarted wasnt paying attn, too sleepy.
I flashed the stock pit and tar from an epic onto the cappy and now it wont even turn on. Wont respond to anything.
Cant get it in to download. No life at all,Shes dead captain, kinda thing.
So it started out i was going to flash back to something other than trident/cm7.
Im bought the car dock and was going to use the kernal so the dock would actually work.
Well it was like any other flash ive done countless times.. Till odin preformed an illegal operation and then it dawned on me what i did.. It was still in download but the computer didn't recognize it any longer. So power off and try to go back to dl mode.. the phone wont respond at all. The power button does nothing.. Plugging it in does nothing..
Im pretty sure its dead, thoughts? other than the flamming for being a newb.
ninjaclipse said:
Im retarted wasnt paying attn, too sleepy.
I flashed the stock pit and tar from an epic onto the cappy and now it wont even turn on. Wont respond to anything.
Cant get it in to download. Shes dead captain, kinda thing.
So it started out i was going to flash back to something other than trident/cm7.
Im bought the car dock and was going to use the kernal so the dock would actually work.
Well it was like any other flash ive done countless times.. Till odin preformed an illegal operation and then it dawned on me what i did.. It was still in download but the computer didn't recognize it any longer. So power off and try to go back to dl mode.. the phone wont respond at all. The power button does nothing.. Plugging it in does nothing..
Im pretty sure its dead, thoughts? other than the flamming for being a newb.
Click to expand...
Click to collapse
Jig maybe? Or Jtag if you can find one.
indomikey said:
Jig maybe? Or Jtag if you can find one.
Click to expand...
Click to collapse
Well with the jig it still has to be able to turn on.. I cant get it to even do that
So i dunno.. Thats why im drawing a blank. I would think it would at the very lest be able to get in to dl mode but nothing lol
So you had the 3 button combo working before?
Have you
1 Open Odin one click or the full version to flash what you want
2 plug in the cable to your computer
3 Hold the vol up/down buttons
4 Plug in micro usb to phone?
If that doesn't work try the same process but do this.
1 Open Odin one click or the full version to flash what you want
2 Remove battery from phone
3 Plug phone to computer and hold vol up/down
4 Push battery in
Try those methods if you haven't already. If they don't work a jig might be your best option to get the phone to DL mode.
And a jig seems to work when you really think it wouldn't but try either of these methods first. I was stuck last week when my phone would not power or anything and the second method worked for me.
flashman2002 said:
So you had the 3 button combo working before?
Have you
1 Open Odin one click or the full version to flash what you want
2 plug in the cable to your computer
3 Hold the vol up/down buttons
4 Plug in micro usb to phone?
If that doesn't work try the same process but do this.
1 Open Odin one click or the full version to flash what you want
2 Remove battery from phone
3 Plug phone to computer and hold vol up/down
4 Push battery in
Try those methods if you haven't already. If they don't work a jig might be your best option to get the phone to DL mode.
And a jig seems to work when you really think it wouldn't but try either of these methods first. I was stuck last week when my phone would not power or anything and the second method worked for me.
Click to expand...
Click to collapse
Yepper thats the method ive been using forever to get into dl mode.
And yea tried the the 2nd way too no dice..
Idk what build number your phone is but build 1010 I'd under product advisory. I had a similar issue and brought it to the att service center and got a brand new cappy v 1008
Sent from my SGH-I897 using XDA App
kwhee07 said:
Idk what build number your phone is but build 1010 I'd under product advisory. I had a similar issue and brought it to the att service center and got a brand new cappy v 1008
Sent from my SGH-I897 using XDA App
Click to expand...
Click to collapse
Off topic, you had a 1010 build, got a replace that is 1008 and you think it's new.
Caution swyping! Read at your own risk.
It sounds dead sir. No idea what ODIN did, but if it's not responding to the power, charger, usb, combo-tricks, etc. It sounds like it's been perma-bricked
If it's still under warranty, it's certainly worth trying to get it replaced... "What the hell is wrong with this phone? It won't turn on anymore?!"
venomio said:
It sounds dead sir. No idea what ODIN did, but if it's not responding to the power, charger, usb, combo-tricks, etc. It sounds like it's been perma-bricked
If it's still under warranty, it's certainly worth trying to get it replaced... "What the hell is wrong with this phone? It won't turn on anymore?!"
Click to expand...
Click to collapse
Can still try a jig.
Look up connexion2005 on this site or get in touch with him on mobiletechreview.com you can also look him up on youtube and his rom in a flash videos. Ghats how I got in touch with him when my phone was fubard and 4 days after I shipped it to him I got it back working like new.
Its well worth the effort to get in touch with him. He is a good guy and I'm sure he can help you.
Sent from my SAMSUNG-SGH-I897 using XDA Premium App
there is no point using a jig. return for warranty. play dumb.
So I made a jig and still dead as anything. Weird, oh well anyone think of anything else? Prob going to see about trying to get art to replace it. Or pay the insurance
Your battery isn't dead is it?
Ha nope at last recall it was around 80% before it happened. And I also tried a fully charged battery from an epic
Sent from my PC36100 using XDA Premium App
I find it hard to believe since a bad flash killed my battery from 96%. But I'm not there so I can't say otherwise. The homemade jig thing from radioshack did not work for me though. I had to use one that was made by one of the members here. I had it plugged in, popped in the battery, and it fired up. Try a couple different combos and see if you get lucky. If I remember correctly it was like 3 tries for me
Yep, verified she's dead..
I hacked a usb cord, and teseted it on an Epic. worked great for the epic..
but the same method on the cappy and she's still dead no life..
/sad panda
how did you make the jig? i bricked mine not to long ago... i didnt use the 301k resistor that you hear about in other threads... i went to radio shack bought a pack of 100k resistors and a pack of 1k .... i soldered three of the 100k and one of the 1k, end to end... then soldered it to the 4 and 5 pin on the stripped charger plug.... this will work... the firmware/kernal/rom changes you have made shouldnt affect the phones ability to get into download mode....
I find it hard to believe since a bad flash killed my battery from 96%. But I'm not there so I can't say otherwise. The homemade jig thing from radioshack did not work for me though. I had to use one that was made by one of the members here. I had it plugged in, popped in the battery, and it fired up. Try a couple different combos and see if you get lucky. If I remember correctly it was like 3 tries for me
Click to expand...
Click to collapse
you dont know what your doing then... if the jig you use from the members worked then you deffinately didnt make urs right.... search these threads there are pictures of what pins to use... you actually dont even have to solder them... just stick the stripped down plug in and touch the ends of the jig to the correct pins... however... do not touch the the actual wires of the jig as it will change the resistance, if that happens it will appear that the jig doesnt work... this is SIMPLE! and if you cant get it to work then youre not following directions, also as he said above.. it doesnt matter that you had 80% before... make sure your battery is charged and try your jig again... that is if you even made one to begin with...
g8tes69 said:
you dont know what your doing then... if the jig you use from the members worked then you deffinately didnt make urs right.... search these threads there are pictures of what pins to use... you actually dont even have to solder them... just stick the stripped down plug in and touch the ends of the jig to the correct pins... however... do not touch the the actual wires of the jig as it will change the resistance, if that happens it will appear that the jig doesnt work... this is SIMPLE! and if you cant get it to work then youre not following directions, also as he said above.. it doesnt matter that you had 80% before... make sure your battery is charged and try your jig again... that is if you even made one to begin with...
Click to expand...
Click to collapse
Cut the guy some slack. Unless you know him or work with him, how do you know he hasn't?
Anyway. Look, I had a similar issue with odin. I didn't run it as admin on win7 and it froze about half way. I unplugged and popped the battery, next thing, it wouldn't start. Since I knew my phone wouldn't work with the 3 button, stock, I tried something else. I let the phone sit for about 5 minutes, came back, put in battery, held the volume buttons as I inserted the usb. Snapped right into download mode.
Not everything works for the same device. It could be that your jig has something wrong with it. Just a thought.
But a hint for the community, unless you know the person you are speaking to personally, don't assume he's lazy and hasn't made his jig.
g8tes69 said:
how did you make the jig? i bricked mine not to long ago... i didnt use the 301k resistor that you hear about in other threads... i went to radio shack bought a pack of 100k resistors and a pack of 1k .... i soldered three of the 100k and one of the 1k, end to end... then soldered it to the 4 and 5 pin on the stripped charger plug.... this will work... the firmware/kernal/rom changes you have made shouldnt affect the phones ability to get into download mode....
Click to expand...
Click to collapse
I exposed the micro usb connector and connected the resistors to the contacts on the board..
Proved that it worked on a epic, booted into dl mode without problem. tried on the cappy and nothing..
Got josh's jig last night. Tried that as well and nothing..
Hi there!
I got me my third Galaxy and this time the three buttons combo doesn't work, so no download or recovery mode from me.
I plan always to stick to Kies updates from now on, but if I ever need to install a cooked ROM for some reason, or even do some special tweaking, I may need to have these modes enabled.
As much as I wanted to at first, I've refrained to apply the bootloader fixes since there's a small chance that they might not work and brick (again) the phone, and I can really cope with this problem all over again
So... what I did was to order one USB JIG from eBay 10 minutes ago. Now I'm wondering... which metod is "better"? The buttons combo or the JIG? If it's so easy to boot into download mode with the JIG (and I'd even think that more reliable since it's a hardware jumper rather than software), why would so many risk into flashing the bootloader when they could have got a nice, little USB cased JIG for 7 USD?
Also... when fully bricked (i.e., black screen) and the buttons combo doesn't work, would the hardware JIG work?
By the way, another reason to not flash the bootloader fix for me is that it would change my GT-I9000T startup screen for the international, GT-I9000 one , and I wanted it to be as stock as possible.
Thanks in advance guys; hope that you can shed some light into it.
EDIT: oh... is it true (confirmed) that phones with the combo disabled by Samsung boot a little faster than the others? I've read that since the combo is disabled, the bootloader doesn't wait for it, so it breezes through the startup process , but haven't seen this confirmed anywhere
Anyone??
mmm... I would like to know this as well.
http://forum.xda-developers.com/showthread.php?t=845115
Made a similar topic.
dhiru1602 said:
http://forum.xda-developers.com/showthread.php?t=845115
Made a similar topic.
Click to expand...
Click to collapse
Yeah, yours is the only post I've found about this in Google before starting my own.
I started this again because all the responses you got was "Good job!" from a guy
Hope we can more information this time...
So... ??? Please, somebody comment on this if possible; thanks guys
Hi!
Phones with the combo available are not any slower than their fellows without it. Mine came without the 3button-combo and flashed the fix to be able to get into recovery. I didn't see any difference.
But if you want to stay on the safe side.. the jig will do the job. Btw i just used the 301k ohm resistor with some clear tape and touched the right pins inside the microUSB socket. Tadaaa... cost me £0.48 How-to on youtube.
The jig doesn't work if your phone has a black screen. That means the bootloader is corrupted, no chance to flash it.
However if it's semi-bricked (you see a PC..!..Phone figure on the screen but no response nor boot) the jig (and only that!) can still help. Basically that's why i have it now
Thanks! I just received the JIGs I bought from eBay (after more than a month...!) and I'm happy with them.
I don't know why I'd risk flashing the 3 button fix when a simple jig is a "pure" and elegant solution, that doesn't mess around with my phone (and its boot screen! )
Thanks, and if you have any more thoughts on the matter, please let me know.
I have usb jig fantastic thing plug it in switch on phone download or plug in while on and hold power button till reset again download i will not three button again
Sent from my GT-I9000 using XDA App
Thanks! Jig is winning so far!
Jig was developed for those phones that will not or cannot use the official method of accessing download mode .
jje
JJEgan said:
Jig was developed for those phones that will not or cannot use the official method of accessing download mode .
jje
Click to expand...
Click to collapse
Yes... I know that, but I was wondering if there was actually some benefits of one method over the other...
Dan_Aykroyd said:
Yes... I know that, but I was wondering if there was actually some benefits of one method over the other...
Click to expand...
Click to collapse
I updated my bootloaders months ago so I could use the 3 buttons and haven't looked back since. I only had a vague idea of what I was doing (much lees that I do know) read all the guides and flashed and I'm glad I did it, now I can enter download and/or recovery on cue whenever I wish..
HI everyone.
Im wuold really need some help with this problem.
My phone have had some problems with connecting with usb earlyer and its been coin flip will pc regonize it, well after instaaling some apps and making back up before that i noticed that im getting black screen and have to reboot to get my galaxy screen working back.
FInally i made factory reset but then i got really big problem, when i start galaxy it shows the galaxy text and after it that flashing S logo but after it screen goes black and thats pretty much it!
Also usb not working dont know shuold it be in that state working!?
And pressing those 3 buttons wont do anything have tried multipletimes everyday, so my phone has locked me out pretty good is there any solutions on that? Or is my phone totally ****ed up?
Hopefully you will be able to cure it with the jig method (look in dev section)
Sent from gt i9000 insanity 8.5/fugumod
What rom where you on before ?
Well phone where updated with Froyo 2.1 but nothing else. oh it were also rooted and thats about it! have been thinking about to sending phone back to the manufacturer! dont really have time trying to find some cure for it.
Rooting = no warranty so you would be best to clear it via jig just in case .
jje
rere
hi there it been longtime since i wroted here.
Well i tryed the jig method with usb cable and with single 300k resistance, made little mistake not to measure it before because there is a 5% tolerance with it so my resistance were only 294k. Doesnt work btw phone dont do anything with it, well i have to make new cable and be sure that it is the 301k resistance. will be adding new info after it what will happen. Im slightly scare that even getting that right resistance it wount do anything, it wuold be that point when i will send it to samsung and maybe get it working again.
Downloading...
okay. next problem with jig managed to get my phone to download mode!! JIIHAA
but now my computer cant regonize it!? actually this problem had before the magical black screen. Any solutions for that? have installed new usb drivers and oldones but cant find it.
PLS need more help!!
Sounds like you need to clean the cable. I've had a hell of a time with these issues in the past. When it is on again off again (or you just get 'generic device' or unkown device) then try cleaning the port on the computer with running alcholol and something tiny enough to get in there.
I did that after a huge long search on here and it was like freakin magic. 8 drivers popped up all at once!
Never hurts to do the comp and the cable too (and make sure its not a charging only micro usb...).
G
Hello ,
Y'day was updating my captivate tru samsung kies mini.
The kies downloaded the latest firmware and phone was in downloading mode .
All of sudden kies min said upgrade not sucessful and informed to remove the battery and try again in recover mode.
But the the phone does not want to turn on or do any thing even with 3 button mode recovery.
Its just powered OFF mode.
I have tried the usb cable jig with 300k resistors also no luck.
any help appreciated guys.
Thanks in advance.
Mine also did this, and I called AT&T. If it's under warranty you'll receive a refurb, if not AT&T may replace it for free if you can sweet talk them like I did. Just make sure they understand nothing you did was the reason it will not turn on, and try not to get snippy with them even though it's so easy, because they seem so dense.
They will make you go thru trying another battery, and cable. Just tell them you have already did this. I already tried the new battery in my old phone just to make sure. It still will not power on normally, or go into download mode with my dongle.
If AT&T won't replace it, then you Will have to contact adam outler, or mobiletechvideos.com for the unbrickable mod.
no use in creating a usb jig either to unbrick
May be I will have to send this to get it JTAG.
I am ok in soldering etc , so if any one has the instructions for JTAG please post it.
hsraghu said:
May be I will have to send this to get it JTAG.
I am ok in soldering etc , so if any one has the instructions for JTAG please post it.
Click to expand...
Click to collapse
From what I understand, you'll probably have better luck with Unbrickable Mod than JTAG if you're going to do the soldering yourself. On top of that, you'll have the added benefit of never having to worry about bricking again.
UBM is much easier to do than the Jtag. Instructions for UBM found here
Before you go taking your phone apart try plugging it into the computer and seeing if it even registers it.
So, I tried to update my Captivate to Gingerbread via Kies to prep it for CM10, and it hung on the 'Firmware Upgrade' Eventually, I pulled the plug and tried the 'Emergency Recovery' That ended up hanging too. And now my phone is completely unresponsive.
I don't see the Computer-- >Phone icon, I can't boot into download mode, nothing, just a black screen.
I tried pulling the battery, sim card, etc. and nothing. Plugging it into the wall also has zero noticeable effect. Am I SOL or is there some hope of resurrecting this beast?
If a Jig doesn't put ya in Download mode...then it sounds like u need the assistance of someone like mobiletechvideos.com
Check out my sig link below for links on how to make a jig and or where to buy one.
Sent from my SGH-I777 using xda premium
I don't think a jig will work, I get zero response from plugging in a USB cable. I'll look into the JTAG stuff. Or hope the Nexus 4 is back in stock sooner than later!
Thanks for the info.
straytoaster said:
I don't think a jig will work, I get zero response from plugging in a USB cable. I'll look into the JTAG stuff. Or hope the Nexus 4 is back in stock sooner than later!
Thanks for the info.
Click to expand...
Click to collapse
As long as your phone is charged, a jig might work. You don't need to be getting response from your phone for it to work.
JTAG is last resort but if ever needed, mobiletechvideos .com offers it.
My phone also dead like yours. No signs of life., jig works for me