Related
Hello I have a blueangel Ph20b2 aka Qtek9090 try an upgrade of the rom and ruling .. I was just turning on the device with serial and V2.07 I can do .. I have read by the network that has been left without the Romany and non interacts between soft and hard .. There is some system to revive .. Some software anything .. Since connect the PDA at the base i usb of the laptop does not recognize no nothing.
Eeeeehmmmm, yes, nice. But we do not understand a word. Was it google-translated or something?
If you did something wron during upgrade, just do the upgrade again. Follow the procedure step after step, do not omit even one step - try to understand what are you doing and what for.
Without more understandable information (about what were you doing and what is happening) we cannot help you.
Stupid mistake - Serial 2.07
Reading between the lines of the original post I suspect the author has done the same as me - or at least ended up with the same result. Anybody know of a fix.
Cause; I attempted to restore from backup over wifi (yes wifi - I was desperate & didnt have the cradle available).
Result; my XDA 2s went blank and now displays a screen displaying "Serial V2.07" (or "USB V2.07" when in the cradle). No amount of re-attempting to re-connect to the device works. I'v tried soft / hard resets / battery removal etc. I'm using Microsoft ActiveSync V4.5. The XDA is an O2 badged variant.
I suspect I'm looking for a boot strap load program that will repair the xda rom such that i can subsequently reload its operating system. Any positive suggestions gratefully received.
just found reference to putting xda2s into bootloader mode "soft reset button,power button and center of D-pad button together" - this still leaves the screen saying "Serial v2.07" - Am I already in bootloader mode? - if it is what do I do next?
Fixed
problem solved - I went back to the 2nd posters answer and attmpted from the begining to install Xda_IIs_Upgrade_v140242.exe, ignoring what was on the xda screen & it worked.
I now have a functioning xda - but I still have with the problem I was trying to solve in the first place.
After a the xbackup restore, the xda desktop isnt re-written cleanly, it overlays semi-transparently on top of the last program run. The desktop accepts stylus commands to run programs which open and display cleanly. How can I clean this up - I dont want to loose O/S DBs e.g. my messages etc. - I dont see a way I can port them across upgrades so I can not just stick with the Xda_IIs_Upgrade_v140242.exe
I feel if they have not understood anything written .. I do not understand Spanish and in English .. I have the problem of serial V.2.07 screen .. Where can I download a rom for qtek9090. In my pda you do a hard reset buttons with record power + + reset and still continues to do nothing with serial on the screen .. If there is any mistake in what they write what I am using the translator google
i got the same problem ...screen saying "Serial v2.07" - Am I already in bootloader mode? - if it is what do I do next?
hate to throw my phone in the garbage can
please someone help meee
anybody found any news?
still in bootloader mode, error 112 at stage 3. BA turns off when trying to update.
2much 4me
anybody come back from this point to wm3?
Device: HTC TyTN II
Bootloader: KAIS130
SPL-3.28.0000
CPLD-8
ROM: RUU_Kaiser_HTC_WWE_3.28.405.0_radio_sign_25.83.40.02_1.65.16.25_Ship
Problem: I tried to sync the device with my desktop (running XP Media Center edition sp3) using ActiveSync 4.5 like I normally do. However, this time the device wouldn't sync and it would just hang. I unplugged the device from USB so that I could try again. The phone immediately went into bootloader. It is currently stuck in this mode.
Steps taken:
First I called HTC tech support hotline. The rep walked me through several steps, but nothing fixed the problem. We tried soft resetting, holding down the power + camera buttons and then soft resetting, hard resetting: nothing worked. He then stated that the device's ROM probably got erased when I unplugged it from USB. He instructed me to download the official 6.1 ROM from HTCs website and then try to re-flash the phone.
I tried doing this, but I still cannot get the ROM onto the device. In bootloader, I plug the device into USB and I get an error message that the device is not recognized. I soft reset the phone and then run the RUU and it begins to flash the device. After 10 minutes, I get a message saying that the flash was successful but the phone just resets back to bootloader.
After searching through the forum and wiki, I am still at a loss as to how to proceed without instruction from an expert. I think I read something about using mtty, but I am afraid to do so on the Kaiser because I read that typing the wrong instructions could be disastrous.
I humbly request any kind Kaiser experts to help me with my problem! Thanks
sir topas said:
Device: HTC TyTN II
Bootloader: KAIS130
SPL-3.28.0000
CPLD-8
ROM: RUU_Kaiser_HTC_WWE_3.28.405.0_radio_sign_25.83.40.02_1.65.16.25_Ship
Problem: I tried to sync the device with my desktop (running XP Media Center edition sp3) using ActiveSync 4.5 like I normally do. However, this time the device wouldn't sync and it would just hang. I unplugged the device from USB so that I could try again. The phone immediately went into bootloader. It is currently stuck in this mode.
Steps taken:
First I called HTC tech support hotline. The rep walked me through several steps, but nothing fixed the problem. We tried soft resetting, holding down the power + camera buttons and then soft resetting, hard resetting: nothing worked. He then stated that the device's ROM probably got erased when I unplugged it from USB. He instructed me to download the official 6.1 ROM from HTCs website and then try to re-flash the phone.
I tried doing this, but I still cannot get the ROM onto the device. In bootloader, I plug the device into USB and I get an error message that the device is not recognized. I soft reset the phone and then run the RUU and it begins to flash the device. After 10 minutes, I get a message saying that the flash was successful but the phone just resets back to bootloader.
After searching through the forum and wiki, I am still at a loss as to how to proceed without instruction from an expert. I think I read something about using mtty, but I am afraid to do so on the Kaiser because I read that typing the wrong instructions could be disastrous.
I humbly request any kind Kaiser experts to help me with my problem! Thanks
Click to expand...
Click to collapse
I suggest getting in touch with the moderator named GSLEON3. He is probably going to be your best bet of getting back up and running. Good Luck
Ok, I can't get in touch with GSLEON3 (I'm sure he's extremely busy) and I don't want to pester him so if anyone else out there can help, I certainly appreciate it. Here is my theory for the solution based on further reading of these forums (but since I have no technical training I don't know if I am even on the right track). I'd appreciate if anyone with the proper knowledge can confirm or reject this course of action:
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
(taken from http://forum.xda-developers.com/showthread.php?t=394543&highlight=stuck+bootloader)
redbandana cautions that one must use HardSPL or risk bricking the device. However, in the post about SPL Questions it states:
"Well, at the moment this is where we are at. We are still investigating the full effects of what an SPL can do to vary the performance of an OS. For now there is a large consensus that the newer HTC 6.1 ROM SPL seems to work well for most of the newer 6.1 ROMS (stock and cooked)."
So my question is, will the stock SPL that came with the official HTC 6.1 ROM be ok to use mtty, or do I need to flash the old HardSPL?
I appreciate any advice on how to proceed, especially if I am totally wrong about how to fix this. Thanks!
sir topas said:
Ok, I can't get in touch with GSLEON3 (I'm sure he's extremely busy) and I don't want to pester him so if anyone else out there can help, I certainly appreciate it. Here is my theory for the solution based on further reading of these forums (but since I have no technical training I don't know if I am even on the right track). I'd appreciate if anyone with the proper knowledge can confirm or reject this course of action:
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
(taken from http://forum.xda-developers.com/showthread.php?t=394543&highlight=stuck+bootloader)
redbandana cautions that one must use HardSPL or risk bricking the device. However, in the post about SPL Questions it states:
"Well, at the moment this is where we are at. We are still investigating the full effects of what an SPL can do to vary the performance of an OS. For now there is a large consensus that the newer HTC 6.1 ROM SPL seems to work well for most of the newer 6.1 ROMS (stock and cooked)."
So my question is, will the stock SPL that came with the official HTC 6.1 ROM be ok to use mtty, or do I need to flash the old HardSPL?
I appreciate any advice on how to proceed, especially if I am totally wrong about how to fix this. Thanks!
Click to expand...
Click to collapse
mtty is not a toy and there are some risks of bricking involved. Anyhow, it is a tool that is used for situations similar to yours. Follow the steps that are provided. Step 3 may be different for different pc's, so just look for port 1. After you run mtty, install a version of hard spl. If you plan on installing a 6.1 rom, install a spl that is compatible with it such as, 3.28hard, 3.29, or the new 3.56. I'll be around for an hour feel free to pm me.
Sorry mate, usually takes me a day to catch up with my PM's, etc...
I can't say for sure on the 3.28 SPL as I have not disassembled it. Well, technically I did, just to prove a point that it was the same as 3.29, but I didn't document any of the commands.
The 3.28 HardSPL is NOT an MFG spl, so it definitely WON'T support some functions. I don't know what all the fuss is about SPL's. I use my own customized version, based of course on Jocky's work, but it's still a 1.1 SPL version & I never have any trouble.
For the 3.28 & .29 SPL's, I do know that if you are stuck because of an RUUNBH error, the correct sequence is:
cmd>set 16 0
cmd>task 8
Task 8 is not "format", I don't know where you got that & task 0 will freeze out MTTY.
Have you done an info 8 command?
cmd>info 8
That will tell you more about the issue.
BUT MOST IMPORTANTLY, only connect mtty to USB, not to port. You can mess other things up like external drives, etc. Ports are only when connecting to OEMSBL/Radio Boot Loader.
BTW, a screwed up USB port pin or block can cause this issue as well. Take a look at the pin block, is it perfectly straight?
Ok, here's the weird thing. I was going to try the mtty to do info 8 command, and I powered on the device (it had the SIM card and microSD card removed.) The device started up and performed a hard reset, and then loaded up! It had a ROM on it! Not the original factory ROM that was loaded (which had TomTom preloaded) but the factory ROM I downloaded from the HTC e-club that I tried to flash. I thought my issue was solved, so I put in the SIM card. However, when I turned on the device (with SIM card in) I get the bootloader screen. What the heck is going on?
GSLEON3 said:
BTW, a screwed up USB port pin or block can cause this issue as well. Take a look at the pin block, is it perfectly straight?
Click to expand...
Click to collapse
Yes, it is straight.
Hi everyone,
Thanks for trying to help me. It's all a bit too confusing for me so I just decided to bite the bullet and send it into HTC. Thanks again!
A while ago I tried to Flash a version of WM6 from mfrazzz on my wizard. The installation seemed to go ok, but when I boot it up i coudn't get past the second splash screen. I thought the phone was a gonner until last night, when I gave it another shot putting on Button ROM. I followed these instructions and it worked. The instructions also had me unlock the phone, and that worked fine too. after that I tried updating my IPL and SPL, Right now my IPL is 1.05 and SPL is 3.08
After this I tried unsuccessfully to get WM6, I think I started off trying Faria.
(So here is the actual problem)
After I tried installing Faria unsuccessfully, I couldn't get Button ROM back up. I'm stuck on the second splash screen (picture of a mug of beer in front of the Colosseum). I've tried flashing my phone w/ everything i've got, including button ROM and Love, and nothing works. most of the WM6 Update Utilities won't even connect. Button Rom connects, stalls at 98%, finished and says it was a success, but I'm still hung up on the Splash.
(I'm running WinXP w/ SP2)
I really just want something running on this phone, don't care what it is.
Thank you for your time
Download official stock rom to recover back and download WST_4.2.2 to verify the CID lock/unlock status,most probably its still CID locked.or you can even reflash 'Button's Rom' again.
No, I've tried to reflash button rom many times. It says it works but it gets hung up on the splash. Since I can't get anything to run on it WST won't work (I think)
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
hEY ZABARDAST
zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
I did this when my Wizard stucks on the splash...
Get mtty 1.04 i thin i dont remember exactly but the higher i ever saw.
kill process wcesscom in PC
conect the ppc on Bootloader
click on conection it shows USB if not... start up again the process
then a white screen appears
I type: task 28
then it works a little on some memory directions
I type: task 28 55aa [or something] (its better get the info on wiki cause it works on chip directly)
without unplug the PDA starts the RUU again...
It works for me...
This is a process for HTC Universal but it works on Blue angel and Wizard for sure!
wait a little i will confirm the steps and the exactly words to type in.
you might need clean the ROM or your flash ROM is overcooked.
I can repair your phone !
+ Que PPC said:
I did this when my Wizard stucks on the splash...
...
wait a little i will confirm the steps and the exactly words to type in.
Click to expand...
Click to collapse
Hey + Que PPC!
Have you confiirmed those values? And is your Wizard CID unlocked?
This would be great to confirm working so that all those with CID locked devices could get their phones back - without paying IMEI-check.co.suckourmoney.uk
@ twig2256
If your phone is CID unlocked try Drugstore's method of recovering Splash Screen frozen phones
cheers
YES
The values are the same for every DOC CHIP
When the MTTY conects to USB type exactly this...
task 28
(then it will work formating and cleaning the DOC
then it says succesfully clean
and now type...
task 28 55aa
it again works on the same process you can close the mtty without unplug your device... update your device with a Stock rom.
Actualy I have issues with mtty i dont know why i can acces to USB it say CMD GOD Damn can anybody helps...
This is the link that mestrini said for drug gsm store metod to unfreeze
http://forum.xda-developers.com/showthread.php?t=276963
Hey mestrini see this...
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
even if it is universal it work for Wizard i did it once it works for me. but now it wont why????
zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
can't solve my t-mobile mda
Hi I have a problem trying to exit from bootloader a PDA's friend, so how can I get to work the mtty?
Sometimes i gain exit with mtty of bootloader screen just kill usb conn in activesyng letthe device in bootloader an conect... select USB port click on OK button and then task 28 erase DOC Chip and then task 28 55aa ready to reflash the same rom that has the problem.
but now i try it on my device an aku3 ipl spl 3.08... on bootloader in a PC Vaio with XP home SP3and....
it say invalid comand
so the dir is CMD
NOT USB
how can i get usb on the dir?
Any body knows?
i had the mtty .01, 2.11 and 1.42 and no one works
any idea?
SADNESS!!!!!!!!!!!!!!!!!
Somebody stole my wizard last night i was waiting for the BUS and two guys atacks me with a knife, they took my Wizard and my money. Again... and in some part i saw somebody called INSANAVACA saying that when the Mtty shows CMD we can put "format" and then choose the A character or B character... one of those options is the OS the other one... Neither him knows jeje and dont remember which one to chose... it starts to clean the DOC Chip.
It maybe works... i cant test it so if anyone can do it please, answer this maybe it works and we can get out of the Splash screens and bootloader stucks.
A long time ago I did this steps but the mtty shows me USB. full charge your batt, remove your SD and SIM card... enter in bootloaders... uncheck the activesync allow USB conection and kill Wcescomm.exe in Win XP taskmanager plug your device to usb, open mtty in all the places works even in the desktop... select USB in the drop menu... a blank screen will appear hit enter if it shows USB your done then... type:
task 28 (hit enter)
--it starts tho the cleaning--- done...
task 28 55aa (it works again in the same thing)
Close the mtty dont unplug your device and reflash it with the stock rom 2.26 Tmobile if you unplug the device you can try to plug it again but in the same port... (but my device is SuperCID unlocked) then goes to the custom ROM.
Maybe the "format" can works if in blank screen shows CMD... try it and let us know what happend ok?
I use the 1.42 Version.
hey thanks for the reply on my thread.maybe we can discuss my problem here.
my wizard is stuck at 2nd splash (the one with the ipl,spl,gsm and os versions)
falshing another rom do not fix the problem. ive even downgraded to several WM5 roms like wizard love, button rom and xda-mini s launcher.
i have a g3 cid sim unlocked wizard.
then lately i noticed, after attempting another manual hard reset, it says formatting failed. so maybe i need to force reset it using a pc. but wizard service tool wont work coz it will only work when synced on the pc.
can mtty forceley reset (hard reset) my wizard? how should i do it? what are the commands? thanks
i've read a thread and read meistrinis reply where he pointed out this thread:
http://forum.xda-developers.com/showthread.php?t=276963
hope this one works for me
lets check it!
dielo said:
i've read a thread and read meistrinis reply where he pointed out this thread:
http://forum.xda-developers.com/showthread.php?t=276963
hope this one works for me
Click to expand...
Click to collapse
I have redirect to a Universal commands for mtty but i cant be for sure if all works for wizards!
So download the mtty 1.42
Unplug your MiniSD card
Put your Wizard in bootloader mode
Kill the wcescomm or put in activesync not allow usb conections
then open the mtty
in ports or conectios you will see
com1
com2
com3
IRDA
USB
More or less I dont know deppending how many ports does your pc have.
choose USB
Be sure that your batt is almost 80% a 100% will be great but with 80% is fine
After choose USB dont move anymore and click ok... or connect something like that.
A blank white screen appear....
Then hit enter if it shows USB> type exactly this:
task 28
(it will work on something like clean the DOC CHIP at the end will show again USB>)
then type exactly this:
task 28 55aa
It will work again on something and
It will prepare the DOC Chip for the OS (FORMAT)
The device stills on bootloader so close the mtty dont unplug the device and downgrade to an original ROM WM5
These are the steps if the MTTY shows USB>
Select the USB port
hit enter in white screen
If it shows CMD>
type in the white screen after the CMD>
format
It will shows you what to choose option A or OPTION B
Here is the problem... Which one we need to choose...
and reflash an original ROM.
Tell us what happends please.
I HAVE MORE COMANDS but for G4 AND WHY IT WONT SHOWS USB!!!!!
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
+ Que PPC said:
I have redirect to a Universal commands for mtty but i cant be for sure if all works for wizards!
So download the mtty 1.42
Unplug your MiniSD card
Put your Wizard in bootloader mode
Kill the wcescomm or put in activesync not allow usb conections
then open the mtty
in ports or conectios you will see
com1
com2
com3
IRDA
USB
More or less I dont know deppending how many ports does your pc have.
choose USB
Be sure that your batt is almost 80% a 100% will be great but with 80% is fine
After choose USB dont move anymore and click ok... or connect something like that.
A blank white screen appear....
Then hit enter if it shows USB> type exactly this:
task 28
(it will work on something like clean the DOC CHIP at the end will show again USB>)
then type exactly this:
task 28 55aa
It will work again on something and
It will prepare the DOC Chip for the OS (FORMAT)
The device stills on bootloader so close the mtty dont unplug the device and downgrade to an original ROM WM5
These are the steps if the MTTY shows USB>
Select the USB port
hit enter in white screen
If it shows CMD>
type in the white screen after the CMD>
format
It will shows you what to choose option A or OPTION B
Here is the problem... Which one we need to choose...
and reflash an original ROM.
Tell us what happends please.
I HAVE MORE COMANDS but for G4 AND WHY IT WONT SHOWS USB!!!!!
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
Click to expand...
Click to collapse
hey thanks, though drug_store's method worked for me and now my wizard is working and i have update 3 for my rom. still a big thanks to you for the starting point on where to look at.
Congrats Men!!!!
dielo said:
hey thanks, though drug_store's method worked for me and now my wizard is working and i have update 3 for my rom. still a big thanks to you for the starting point on where to look at.
Click to expand...
Click to collapse
Very good men!!! you're welcome.
Even if this method still hasn't been proved.
Here's a reason i'm taking Rom's out from Stickies.
So there's space for the important things like this on..
Let's face it sometimes a new thread on Bootfreezes and Bricks is more useful then an old one that people get discouraged by, because of it's length.
Made this one Sticky.
Noonski said:
Here's a reason i'm taking Rom's out from Stickies.
So there's space for the important things like this on..
Let's face it sometimes a new thread on Bootfreezes and Bricks is more useful then an old one that people get discouraged by, because of it's length.
Made this one Sticky.
Click to expand...
Click to collapse
great. you're right. thread like this should be stickied.
Wow
Stickie!!! hahaha so glad too see it thanks but.... is not prooved yet... so does anybody wants to try... damn if i had my wizard ...
It gets more renewed Attention to the most important problem.
Maybe....
You've got right!!!
I will make a deal With Tvaril to buy him his wizard but i need more info about to receive packages World wide. and the way to pay jeje...
I hope it can be truth in an easy way.
in the mtty, when i pres enter it getc CMD, when i type format it gets unavailable comand, so im still stuck on the align screen some other help
Man it sucks!!!!
But in sync screen?
Damn this is new huh!
I dont know what else can we do...
does you try to reflash again an originla ROM?
maybe ayou are in troubles cause your battery is too low...
display damage
i just find out that i damaged the lcd with the f****** glue. i was trying to glue the mask and the glue went on the LCD so i f***** up.
by the way the battery was full recharged, and everything was done like you said.
it sound very bad men!!!!!!
Does the display works? or it has issues?
maybe you can find a display.. so sorry to heard that.
Thank you!
thanks for this mate i was using mtty in vista using the compatiblity patch...
i downloaded all the 4 things who know they may be useful at some point of time for me when i need to do stuff.
Have a good day!
Regards,
Sam
good to hear it... but
why dont post the compatibility patch for all members?
come on share it here men!
I download mtty a while back, you know, just in case. Wellllllll, just in case happened yesterday. Mtty made it easy as pie and quick, too. Now, baby's fine and reflashed and happy again!
my friend has the same problem as this, his wizard g4 stuck on splashscreen when he flash love_rom using How to flash a new ROM to your Wizard... a little tutorial!. His problem was solved if he flash rom using this manual (I'm sorry for czech link, english version by Google translator)
Ouch... Tried to install new rom and seem to have buggered up the phone. I get the infamous tri-color screen with usb connection to mtty.... nothing else. I cannot connect through active sync, etc. and of course the phone will not boot into WM. Tri-color screen indicates "security unlocked" , DIAM500 SPL-0.057.0000, MicroP-Diam (LED) VB.
After lots of reading the only option I see is using mtty to install a "working" ROM on the phone but cannot figure out how to accomplish this. Looks like you would need to know a starting address and length of the file in order to use the lnbs command to transfer the image?
Any thoughts or am I just wasting time (which I already have done)
thom2k said:
Ouch... Tried to install new rom and seem to have buggered up the phone. I get the infamous tri-color screen with usb connection to mtty.... nothing else. I cannot connect through active sync, etc. and of course the phone will not boot into WM. Tri-color screen indicates "security unlocked" , DIAM500 SPL-0.057.0000, MicroP-Diam (LED) VB.
After lots of reading the only option I see is using mtty to install a "working" ROM on the phone but cannot figure out how to accomplish this. Looks like you would need to know a starting address and length of the file in order to use the lnbs command to transfer the image?
Any thoughts or am I just wasting time (which I already have done)
Click to expand...
Click to collapse
OK, first thing is to just breathe a few times.
Second is to start reading. Please see link in my signature before doing anything else. Read it, digest it and follow it..
There is a process for flashing a ROM. First, you need to flash Hard-SBL. This does invalidate your warranty (but you must have realised that already right..?)
I believe the phone is locked. Is there any way to unlock from mtty?
thom2k said:
I believe the phone is locked. Is there any way to unlock from mtty?
Click to expand...
Click to collapse
Ok, first of all, I've not personally used MTTY. I've done a forum search on it but not turned up much. Having come from the Blue Angel, I've had to re-learn everything in order to flash a ROM.
Now, did you read the Wiki or did you just automatically think you knew what you were doing..?
Follow this at your own risk. I'm working on limited knowledge here..
As far as I know, your Diamond appears to be in Bootloader mode. The fact that you have the "USB" words on your screen, your PC is going to be able to communicae with the Diamond. (one assumes that it is connected to the PC - Does it say "Serial" when the cable is disconnected..?). Activesync will not show up as connected but you're still going to be able to communicate with it..
From there, you need to download and run Hard-SPL. I would go for the developers edition.
Once the Hard-SPL has been run, you need to choose a ROM - That will be your choice..
Follow this thread to clarify exactly what you need to do..
http://forum.xda-developers.com/showthread.php?t=416211
Let me know how you get on..
Cheers,