SERIAL / V 2.07 In Qtek 9090 Mistake - MDA III, XDA III, PDA2k, 9090 Software Upgrading

Hello I have a blueangel Ph20b2 aka Qtek9090 try an upgrade of the rom and ruling .. I was just turning on the device with serial and V2.07 I can do .. I have read by the network that has been left without the Romany and non interacts between soft and hard .. There is some system to revive .. Some software anything .. Since connect the PDA at the base i usb of the laptop does not recognize no nothing.

Eeeeehmmmm, yes, nice. But we do not understand a word. Was it google-translated or something?
If you did something wron during upgrade, just do the upgrade again. Follow the procedure step after step, do not omit even one step - try to understand what are you doing and what for.
Without more understandable information (about what were you doing and what is happening) we cannot help you.

Stupid mistake - Serial 2.07
Reading between the lines of the original post I suspect the author has done the same as me - or at least ended up with the same result. Anybody know of a fix.
Cause; I attempted to restore from backup over wifi (yes wifi - I was desperate & didnt have the cradle available).
Result; my XDA 2s went blank and now displays a screen displaying "Serial V2.07" (or "USB V2.07" when in the cradle). No amount of re-attempting to re-connect to the device works. I'v tried soft / hard resets / battery removal etc. I'm using Microsoft ActiveSync V4.5. The XDA is an O2 badged variant.
I suspect I'm looking for a boot strap load program that will repair the xda rom such that i can subsequently reload its operating system. Any positive suggestions gratefully received.

just found reference to putting xda2s into bootloader mode "soft reset button,power button and center of D-pad button together" - this still leaves the screen saying "Serial v2.07" - Am I already in bootloader mode? - if it is what do I do next?

Fixed
problem solved - I went back to the 2nd posters answer and attmpted from the begining to install Xda_IIs_Upgrade_v140242.exe, ignoring what was on the xda screen & it worked.
I now have a functioning xda - but I still have with the problem I was trying to solve in the first place.
After a the xbackup restore, the xda desktop isnt re-written cleanly, it overlays semi-transparently on top of the last program run. The desktop accepts stylus commands to run programs which open and display cleanly. How can I clean this up - I dont want to loose O/S DBs e.g. my messages etc. - I dont see a way I can port them across upgrades so I can not just stick with the Xda_IIs_Upgrade_v140242.exe

I feel if they have not understood anything written .. I do not understand Spanish and in English .. I have the problem of serial V.2.07 screen .. Where can I download a rom for qtek9090. In my pda you do a hard reset buttons with record power + + reset and still continues to do nothing with serial on the screen .. If there is any mistake in what they write what I am using the translator google

i got the same problem ...screen saying "Serial v2.07" - Am I already in bootloader mode? - if it is what do I do next?
hate to throw my phone in the garbage can
please someone help meee

anybody found any news?
still in bootloader mode, error 112 at stage 3. BA turns off when trying to update.
2much 4me
anybody come back from this point to wm3?

Related

wizard bootloader in smartphone :(

phone is not powering up
hi , I have a htc typhoon (amadeus) based qtek 8100 phone , by mistake I upgraded bootloader to a htc wizard bootloader rom ( IPL/SPL 1.01 ).Now the phone isn't opening turning on or powering up.When connecting to usb nothing happens.Sometimes, it blinks all of the keyboard lights (maybe sometimes that I play with key combinations). How can I repair and put the right bootloader into phone again ?
Note1: I am pressing cam button and connect usb cable nothing happens.
Note2: I can't access to the bootloader screen
.....wow :roll:
LOL that's perhaps the funniest thing i have read on this site
dehjet said:
phone is not powering up
hi , I have a htc typhoon (amadeus) based qtek 8100 phone , by mistake I upgraded bootloader to a htc wizard bootloader rom ( IPL/SPL 1.01 ).Now the phone isn't opening turning on or powering up.When connecting to usb nothing happens.Sometimes, it blinks all of the keyboard lights (maybe sometimes that I play with key combinations). How can I repair and put the right bootloader into phone again ?
Note1: I am pressing cam button and connect usb cable nothing happens.
Note2: I can't access to the bootloader screen
Click to expand...
Click to collapse
I would pose this question in the dev/hacking forum or on the smartphone dev site.
I'm only guessing here, but unless there is a second bootloader image (the Wizard for example has two copies stored in ROM) that can be booted from or otherwise forced to copy over into the primary space, then you might own a brick.
Actually, you may be able to revive it using a JTAG connector and associated flashing software, but that's specific to your device and would be better addressed over in the Typhoon forums. Essentially you would connect a JTAG connector to the EEPROM inside your phone, and the other end connects to your PC. You'd then need software that can transfer a new bootloader image over to the phone.
[off-topic]
Sorry for saying it like this....
But how the **** did you managed to do this?
Were you drunk or something like that...
[ on-topic]
Are you sure that you can't get it in bootloader mode?
What happens if you get it in bootloader mode and just try to flash it again (although your PC said it isn't connected) ?
The problem is I don't know the JTAG connection points for HTC amadeus based phones.Where should I look ?
Phone is not powering or charcing because of these are also controlled by software.Bootloader mode is not available.(I am talking about charcing even not working or opening the phone , bootloader is impossible)
summiter said:
I would pose this question in the dev/hacking forum or on the smartphone dev site.
I'm only guessing here, but unless there is a second bootloader image (the Wizard for example has two copies stored in ROM) that can be booted from or otherwise forced to copy over into the primary space, then you might own a brick.
Actually, you may be able to revive it using a JTAG connector and associated flashing software, but that's specific to your device and would be better addressed over in the Typhoon forums. Essentially you would connect a JTAG connector to the EEPROM inside your phone, and the other end connects to your PC. You'd then need software that can transfer a new bootloader image over to the phone.
Click to expand...
Click to collapse
i've got the same problem with my herald, and dont know what to do!
phone don't start, when i press cam+com mngr+soft reset, nothing happens
even when i connect it to the batteryloader, nothing happens!
please, i need help! i've already searched the forums all over the world (those in english and french...)
Till now i was afraid to admit this but Brother u gave me courage to admit
"I ONCE FLASHED MY TORNADO WITH TYPHONE ROM"
luckily it was in warrenty and sweet talking + innocent gestures worked and i got a brand new replacement but YOU R THE MAN
Dont worry every one screwed up once
keep reading u might find a solution to wake the dead
GOOD LUCK

Get Stuck on bootloader

Hi,
I have a used qtek 9090 With the Italian version.
When i try to upgrade the rom to a english one, ou upgrade with a original italian version it always get stuck on the bootloader screen.
On the PDA i get a screen only saying usb 2.07.
On the PC it get's trying to retriev information.
If I cancel the operatio after a while I have to run a litle program to get out from bootloader.
So I need your help with this.
My guess is the pda it's locked or something is wrong with the bootloader.
Regards
kruzpt said:
Hi,
I have a used qtek 9090 With the Italian version.
When i try to upgrade the rom to a english one, ou upgrade with a original italian version it always get stuck on the bootloader screen.
On the PDA i get a screen only saying usb 2.07.
On the PC it get's trying to retriev information.
If I cancel the operatio after a while I have to run a litle program to get out from bootloader.
So I need your help with this.
My guess is the pda it's locked or something is wrong with the bootloader.
Regards
Click to expand...
Click to collapse
use Mitty, when stuck on bootscreen
which instruction pass to multi-port tty with device stuck on bl?
I've tried your solution but it doesen't work on my device.
I See again:
- Serial v2. 08 (outside of cradle)
- USB v2. 08 (inside cradle)
My device:
Vodafone VPX 1620
Model PH2OB2
Thanks to all
I also have a Qtek 9090 and am stuck on the "serial v2.08" screen. I've searched all over the internet for the last hour and while this site is (by FAR) the best resource I still haven't been able to get past that screen. I've tried hard and soft resets by holding down the power key, voice record key, and pushing the stylus in the reset button on the bottom with no luck. I've tried just the power and reset buttons and even all four buttons (reset, power, record, camera) - which was a little hard to manage But now I can't figure anything out and could REALLY use some help as I'd hate to have an expensive paperweight after only owning this unit for four days.
Btw, I've gotten to this point while (rather stupidly, in hindsight) clicking on EnterBL.exe during an attempt to upgrade to WM6
Success! I got it after all!

PDA2K stuck on boot screen

i have downloaded update rom v 1.40 form the imate site. and connected my device to my PC via bluetooth link and sync through active sync4.5 and then run the update setup setup found the device v 1.22 and ready to update it to v1.4. and then after the restart (which the setup automaticlly does) a display with out back light appers which says (Serial v2.07). i tried to soft reset and hard reset but nothing happens, on the short i am unable to load os on my device and stucked to this display (Serial v2.07). i do not have data cable or cradel. any solution Please.
****
Moderator edit
Thread moved from news section to Blue Angel Upgrading
****
did you find a solution
because i have the same problem with mine
soegaard71 said:
because i have the same problem with mine
Click to expand...
Click to collapse
I have the same problem but i'am with mda III T-mobile can Any one help me ??????
well i do not want to offend you but you are too stupid to even try the upgrade over bluetooth, the upgrade only can be performed over cable
Get a cradle or a data cable and update according to descriptions in the Wiki. You're in bootloader mode, you should be able to resume the update from here, but ofcourse only by cable.
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM5_Home
worst case scenario is to recover your device using mtty, search the forums for the method
Or you can find it in "the guide" which can be found within the wiki (near xplode ROM)
I really want to improve the wiki - but the ****ing time

[SOLVED] Noob needs help! Is my qtek9100 a brick?

Hi!
this is my first post here, so sorry for my bad english or mistakes
i bought a qtek 9100 on ebay, and i'm wondering if it's a brick or not. i received the device 3 days ago. during this time i read through a LOT of threads here, tried a few things and nothing works.
here is some info:
- the phone is a qtek 9100 without branding
- the IPL is now 1.01 (i flashed "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE" successfully)
- the SPL is 2.18 (because of the missing suffix ".0001" i guess it's a G3)
- GSM is 01.12.10
- OS is 1.5.4.2
- when i start the device (without any button pressed) it stops at the splash screen (which was a qtek logo before flashing, and is now this picture with a beer, that says "some things last forever" )
- i can get into bootloader screen (color screen) by holding camera button while starting
- in bootloader screen a small "USB" appears when i connect cable to usb on pc
- when i press communicate and voice buttons (on the sides) while starting, the "Press send to restore factory default" screen appears, but pressing send prints out "Format FAT Partition Format is Failed"
- the device gets recognized by windows ("Mobile Device" appears on my computer)
- ActiveSync 4.5 does not connect to device, not even as guest.
- when i hit "Connect..." in ActiveSync's connection settings, nothing is found
("Allow USB Connections" is ON)
- the device is CID-locked ("FF" state in Mtty 1.42)
- i can't unlock CID, because i can't get "EnableRapi.cab" onto the device without ActiveSync connection
Ok, these are basically the things i know now. The problem is that i never saw any other screen then the "HTC" boot screen, the "Qtek" splash logo (the one with the clouds) before i flashed with custom ruu wwe, after that i see the new splash logo, and i can get into bootloader (color) screen. I never saw any windows mobile running on this device! I could never establish a connection with ActiveSync!
So i hope that someone here on this nice forum can help me get this device to work (WM5 would even be enough right now) or at least give me a hint!
Thanks in advance!
Put the phone in bootloader mode and flash back to the original ROM.
since i bought it in ebay i don't have the original rom of this device.
but i found "233309-qtek9100_2180707_21807109_20710_qtek_ger_ship.exe" through google, which seems to be an original qtek rom (version 2.18). shall i flash this one?
You can find in the Wiki the latest official roms of every brand for our Wizards .-
ok, thanks.
i found one (Qtek GER 2.18.7) and flashed it. the process was successfull, now the IPL/SPL is both 2.18 . But the device still doesn't start and stops at the splash screen (which is now the original qtek splash again). I can still get into bootloader mode and hard reset results in "Format is failed"! No ActiveSync connection either... how should i proceed now?
i basically narrowed it down to these two problems:
- the splash screen freezes
- hard reset error "Format is failed"
( IPL: 2.18, SPL: 2.18 )
can't anybody help please?
i'm freaking out about this
With everything i’ve read the only people who’ve had any success had CID unlocked devices.
ok, i think that too for what i've read so far...
is there any other way of CID unlocking except lokiwiz (can't copy enablerapi.cab without activesync!)?
would this imei-check service that i've read about work in this case?
meanwhile i've also tried something with mtty (r2sd all) but doesn't work -> "didn't get proper security level"
is this also because of the CID lock? i tried to find out the right password to enter in mtty, but found nothing that worked...
does anybody know the correct password?
I couldent CID unluck my 9100 with lokiwiz so i did it 5min ago with Wizard Service Tool (ha to reboot my computer).
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Look up the orignal rom on the wiki, get into bootloader. And flash it back.
Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse
Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks
Like I sad before
Get into bootloader, flash back the original rom and try again.
mizobuchi said:
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks
Click to expand...
Click to collapse
I put the original rom.
But... the problem is the same.
when I started the device (without any button pressed) it stops at the splash screen (which has a qtek logo before flashing)
- i can get into bootloader screen (color screen) by holding camera button while starting, I installed the original and others rom who days before works perfectly... Now... this stopped at splash screen
- when I tryed to format.. = "Format FAT Partition Format is Failed"
Any idea?
I have tried this : http://forum.gsmhosting.com/vbb/showthread.php?t=332143
but... without success.
Could you help me, please?
Very Thanks
i'm still stuck with the same problem with hang up on qtek splash screen, too!
i have IPL 2.18 and SPL 2.18 and i can get in boot loader screen and connect with usb. (but no activesync connection!)
formatting doesn't work either.
does anybody have an idea how to solve this?? it's frustrating... i've tried almost every guide here on the forums.
same proplem here with
ipl 2.16
and spl 2.16
I used this to fix this problem
Hi i had the same problem the other week, installed a dodgy app, went to do a hard reset and wouldn't do a hard reset format failed. Tried updating rom everything worked ok until you booted it up. Wouldn't go past second splash sreen. After a few hours of trawling round i found this thread.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=format+is+failed
worked for me. Hope this helps you out.
Problem in connecting to my PC
Hey ,
I just bought a qtek 9100 a day before ... I tried to connect it with my computer.. instead of connecting my battery gets charging well can u plz help me out !
is there any software that i should install in my pc in order to get it connected to my PC...... please help me fast ! Lot of work is pending !
Thanks
Salman
Ok guys, I finally have this SOLVED.
My QTEK 9100 is working fine now!!!
I'm so happy with it right now
Since nothing I tried worked, I went to imei-check.co.uk and got my phone completly unlocked! It only cost me about 11€ and since it works now I have to admit that it was worth it (no advertising). After the unlocking was done I could do the "r2sd all"-method (Tool: MTTY 1.42) using a miniSD card. You can find a good tutorial on this board somewhere. After that everything was just fine...
-> I never saw it working and Hell Yeah: This baby just kicks a$$ !!! (although it's kinda 'oldschool' these days )

T5355 stuck on "TOUCH Diamond2" screen

Hi guys!
I have been trying everything that I could find on XDA to fix my problem.
I got this HTC clone a few weeks ago, and it was working fine.
I decided to install a UI on it and it worked fine. After a while I got bored of the UI, so I decided to uninstall it. After the uninstall, the device indicated that it needed to be restarted. I did that, but after it rebooted, it started to reinstall Windows Mobile 6.1. I was annoyed by this, but was like, whatever, and let it continue.
Where the real problem started was when the device froze up (I left it alone for over an hour, but there was no change).
I then had to pull the battery. After I put the battery back into the T5355 it just keeps getting stuck on the "TOUCH Diamond2" screen.
I tried all the hard reset and soft reset tricks I could find and have no been able to either setting it back to factory or bootloader mode.
I was able to find a post that described how to place the boo.ini, flash.bin, and loader.bin file onto my micro sd card. I was able to to get the boot.ini an flash.bin files, but can't seem to find a loader.bin file (it that the actual OS rom?). I then found a post that showed how to use HiSilicon IDT to force the install of the OS Bin file (C02_HTC_20091102_R2127_英全视角B包.bin).
I followed the instructions on placing the T5355 into "Download" mode and pushing the OS bin fine to it.
I am able get the IDT software to detect the T5355 and start pushing the install, but the damned thing ends up giving an XLDR error.
PLEASE! PLEASE! Somebody help me! This phone is brand new and really want to get it working again.
Model: HTC(?) T5355
Please help me someone!!
Is there anyone out there that can help me???
I am so frustrated and can think of what else to do!
The biggest problem I have is that I can't use ActiveSync. If I could use that I wouldn't have much trouble.
Does anyone know how to use HiSilicon's IDT properly? The instructions I was working off of are in Russian. I think that a need a loader.bin file for the T5355 that I can put on my micro sd card...or maybe not...I don't know.
I just really want to get this device back to factory settings.
Please someone take pity on me!!!
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
I don't think you would be experiencing these problems with an original topaz
Please take care this is a HTC CLONE
Pisca said:
Please take care this is a HTC CLONE
Click to expand...
Click to collapse
oups, I'm high resolution on monitor, I thought it was saying "done" not "clone" ) ... there's a thread dedicated to china clones, look here http://forum.xda-developers.com/showthread.php?t=619643
run with a rom in bootloader, it shud work
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
Click to expand...
Click to collapse
DalvuS, thanks for the reply, but the issue is that I can't seem to get into bootloader mode . I wish I could. The T5355 seems to be stuck in the middle of wm 6.1 install. I need to somehow wipe the install and be able to push a reinstall back to the device.
I don't think you would be experiencing these problems with an original topaz
Click to expand...
Click to collapse
Exca that comment doesn't help me. It just makes me more sad. I was gipped when I bought the phone . I thought I paid for a "real" Diamond 2.
If you can't to catch the bootmode, looks like hardware problem.
You can't to repair it at home, imho. Try the specialized service.
..............
... and: are you sure about key combination for bootloader screen for CLONE?
Hello people, how can i dump my rom from my phone (mfu w71) for backup, because i cannot find any rom in english only in chinese. I started to dump the chinese rom with some chinese kitchen (K3系列ROM工具), but i'm stuck. I do not know to do anymore i have extracted ROM, SYS folder. I think it would be good to start another section on this forum for the chinese phones.
Some help from experienced cookers would me be much apreciated.
My T5355 is up and working!!!
Thanks to everyone who replied to my post!!!
I discovered that the problem was that the PC I was attempting the install from was running an AMD based processor.
I tried on the family laptop (which runs an Intel processor) and the install worked!
I AM SOOOO HAPPY!!!
b0gdi good luck with your issue. Try doing a search here in XDA for "dump my phone".
nothing[switched off] -> press start -> command -> bootloader -> bootloader commands -> system start -> play
checking one by one by interfering would have done the trick
I'm glad to hear that... so now you're ok
NEXT !
help me please
i Have Flash my phone 100 times with IDT for WM6.5 and WM6.1 all the versions my phone is T5355 Hot D2 but in one day i flash a rom that kill my phone the phone are conntinue to work but no screen picture only light i have try some russian Rom that kill my phone
the phone was been on guerant so i send him back to my supplier thay fix the phone but the factory said that thay need to change the screen so now thay really change the screen and the phone back to me with WM6.1 some New version 20.1.2010 some think like this i have made a call but the phone hang up and not make calls so i try to put him Back the WM6.5 English ROM that i use with this phone before i try to Flash Russian ROM that brake me the picture of the phone and block me the Bootloader Combination of SEnd+End+Power so that way i send him to repair .
so i try the English Rom that i have use before he DOwnload the Flash Fine but now the screen are stop to show picture But the Bootloader are work fine
so i try all the Roms that i have and all the same the screen dont want to show picture
some body have a same problem or can help me with this ?

Categories

Resources