Get Stuck on bootloader - MDA III, XDA III, PDA2k, 9090 Software Upgrading

Hi,
I have a used qtek 9090 With the Italian version.
When i try to upgrade the rom to a english one, ou upgrade with a original italian version it always get stuck on the bootloader screen.
On the PDA i get a screen only saying usb 2.07.
On the PC it get's trying to retriev information.
If I cancel the operatio after a while I have to run a litle program to get out from bootloader.
So I need your help with this.
My guess is the pda it's locked or something is wrong with the bootloader.
Regards

kruzpt said:
Hi,
I have a used qtek 9090 With the Italian version.
When i try to upgrade the rom to a english one, ou upgrade with a original italian version it always get stuck on the bootloader screen.
On the PDA i get a screen only saying usb 2.07.
On the PC it get's trying to retriev information.
If I cancel the operatio after a while I have to run a litle program to get out from bootloader.
So I need your help with this.
My guess is the pda it's locked or something is wrong with the bootloader.
Regards
Click to expand...
Click to collapse
use Mitty, when stuck on bootscreen

which instruction pass to multi-port tty with device stuck on bl?
I've tried your solution but it doesen't work on my device.
I See again:
- Serial v2. 08 (outside of cradle)
- USB v2. 08 (inside cradle)
My device:
Vodafone VPX 1620
Model PH2OB2
Thanks to all

I also have a Qtek 9090 and am stuck on the "serial v2.08" screen. I've searched all over the internet for the last hour and while this site is (by FAR) the best resource I still haven't been able to get past that screen. I've tried hard and soft resets by holding down the power key, voice record key, and pushing the stylus in the reset button on the bottom with no luck. I've tried just the power and reset buttons and even all four buttons (reset, power, record, camera) - which was a little hard to manage But now I can't figure anything out and could REALLY use some help as I'd hate to have an expensive paperweight after only owning this unit for four days.
Btw, I've gotten to this point while (rather stupidly, in hindsight) clicking on EnterBL.exe during an attempt to upgrade to WM6

Success! I got it after all!

Related

Think I have killed my dad's phone !! HELP

Was updating my dads SPV M700 to WM6 and have hit a problem ....
The rom image updated ok, and I used AX3L's 2.0.8.
Unfortunately during the GSM update the software crashed, and froze at 51%. I had to re-boot and now I can't use the phone.
When I re-set the phone it says No GSM at the HTC screen and then stops loading at the WM6 front page.
I can get into the Bootloader by pressing the Power/Camera/Reset buttons, but when I try to re-flash GSM is says error 270, corrupt image. I have tried several files with no luck.
I would appreciate a hand ..... My dad is going to kill me
Thanks
gaz_az
try press
power button + camera + reset
to enter usb mode
then reflash the radio again.
hope this works
You can try 2 other things!
Download the Radio ROM again- you may have had a downlaod glitch in the 1st one. V1.38 is the best one to try.
Download and install the offical HTC WM5 ROM- this should be a full ROM including Radio, so sometimes completes more effectively. If you are brave, you can them retry the WM6 flash!
since bricking a hermes i stopped taking chances doing rom upgrades via usb..
the method that is most reliable ad safe is... via SD card
extract RUU_signed file from the upgrade pack (use winrar) and then copy it to the root of a blank sd (mini or micro etc) and rename to TRINIMG.nbh ..enter bootloader and follow the steps.. its fast and most reliable
Ok - Thanks for the help, but no luck so far. I have tried the suggestions above !
Heres what I have done ...
Hard reset - no change
Tried to re-flash with WM6 and WM5 cooked roms, but an error comes up saying the images are corrupt. This happens with any image I try.
I have also tried a legit HTC WM5 rom upgrade image, but it doesn't work either. It gives an error at 1% saying invalid device ID.
What I can do it get into the standard bootloader screen, which shows I have a USB connection when plugged in. If I allow the phone to boot up it stops at the WM6.0 picture. It won't go far enough to allow me to get an activesync connection.
ANy more adivice would be greatly appreciated !
gaz_az
Next thing then, is to try and obtain a downloaded Orange M700 ROM- there are a few links hereabouts.
For some reason, your device seems to want only its home ROM. If that fails there are other methods before sending back to Orange!
I downloaded an Orange rom, but still no luck. It gets to 1% again, then says there is a error/corrupt image file. Same as any of other cooked images !
What next ??
well if you were my son, i would advice you,to buy a plane ticket for somewhere very far,leave the house while i sleep,and pray every day you have left in your life,for not find you on my way
uhm, question about boot loader and flash on boot loader mode.
I copy file TRINIMG.nbh to root card mini SD, and i can't go as you say...
always Tri colors screen....
gaz_az said:
I downloaded an Orange rom, but still no luck. It gets to 1% again, then says there is a error/corrupt image file. Same as any of other cooked images !
What next ??
Click to expand...
Click to collapse
You are running out of options
Your choices now are to go further down the 'fiddling' route, or give up and return the phone to Orange for repair. At least if its is stuck in bootloader, they may not spot that you have been meddling
If you want to play more, there are very few Trinity specific fixes, but possibly some of the questions/answers in the Hermes WiKi may help, though the Bootloader versions etc won't be relevant.
[Edit: When you are in Bootloader mode, what version numbers are showing on the screen?]
is it so wrong i was smiling when i read this.
does make me wonder if u told ur dad what u were going to do or whether u were trying to be cocky by giving him a better phone without him knowing.
all i can say is, UNLUCKY !
I must say things are looking bad - I think it would take an original orange SPV rom if I could get one. Been to the orange website, but no luck !! Anyone know if orange released one ??
Been looking at the Hermes unbrick thread. Is there a way to enter KITL debug mode in the trinity ??
G
P.S. Dad knew I was upgrading the phone, already did it once for him and it went ok. No sure he knew I could acutually kill it
No Orange haven't released an official rom.
Well Orange UK haven't Orange FR have, so unless he speaks and reads french that's not an option.
Well, French or not, you've probably got nothing to lose by trying to load the official French ROM
Go Here and click the Mise-a-jour link (which is French for ROM) and it will open a zip file download without the need to verify the IMEI number.
If that doesn't work, nothing will! If it does load, you will at least have a working phone, even if it is in French, and you can go back over the ROM update again, remembering to apply the SPL Bootloader first!
Still "not allow", i don't know what the hell Orange was doing with P3600?
Lock everything?........it's suck !!!
No luck with the French ROM. Same thing gives an error message about wrong device ID.
I am one step from chucking it in the bin. Any more last minute ideas ??
erh, bizzard,i can't use "wtty.exe" to view my CID ...
i tape "info 2"and it always appear
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
...............................
Someone have issue for that?
If i can view CID code,i think i can find the right ROM to re-vivre...all suck !!!
erh, hey guy, your boot loader is english or french? sorry if it's the most stupid question of the day......i think french device use french boot loader,right?
i mean, when screen tri-color appear, use mini SD card to flash ROM, the language it apprear itself is english or french.
p/s : i was telephone to the HTC center, and they say as usual, send it to the center repair.
For french user address is : be sure u have enough garanty which required.
send them and make them crazy.....
CIRMA ELECTRONIQUE
9A14 CHEMIN DE BARATEAU
ZONE INDUSTRIEL DE LA LANDE
33451 SAINT Loubès
If you can figure out how to compile splxploit, you can fix this, see
http://forum.xda-developers.com/showthread.php?t=308691
thank anyway,i will try it before tomorrow,cause i will send them my device for repair.

How to Flash in BootLoader

I have a stuck image on my 8125. The phone "boots" but only shows a white screen, and is unusable.
The "a2sd all" restore option mentioned in the forums doesnt work for me. I have read on several forums that I should be able to reflash the OS from the bootloader, though I cant find any instructions on how to do this
Could someone point me in the right direction for how to flash an OS VIA bootloader?
Thx
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Mirek - not to be totally ignorant, but the step 4 is what I'm having problems with .... where can I find either a providers ROM, or something that I can actually use while in bootloader mode?
Thanks!
NM ... Found it!
For anyone reading this .... You can get the provider ROM for the 8125 from HTCAmerica here: http://www.htcamerica.net/support/8125/software-downloads.html
Thanks for your help!
mirekluza said:
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Click to expand...
Click to collapse
Dear Readers,
I'm having problem with my Dopod 900(,Qtek 9000,HTC Universal,O2 Xda Exec,Jasjar ). Can somebody please tell me what to do?
Before this, every time somebody called, the PDA lost the network bar and start to search or network and reject the calls automatically and also i wasn't able to send SMS. Now, i tried to install WM6 crossbow, the phone even cannot be on !!! even when i connect it to the charger, even the light will not be on. the only page that i can see is a white page asks Press 0 to Restore factory default or press X to exit. either perss 0 or X, the phone will be off and i cant turn it on with power key....
Please tell me what can i do ?? I really need your help.
PLEASE REPLY, PLEASE.
[email protected]
Warm Regards to All
G-Jorji
brick?
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
WHAT did you downgrade from?
Did you re-unlock your G3?
How's your battery?
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
IPL/SPL 2.08? Does that exist? Do you mean 3.08?
Are you sure your device is a G3? Or you killed it when flashing Button's ROM?

SERIAL / V 2.07 In Qtek 9090 Mistake

Hello I have a blueangel Ph20b2 aka Qtek9090 try an upgrade of the rom and ruling .. I was just turning on the device with serial and V2.07 I can do .. I have read by the network that has been left without the Romany and non interacts between soft and hard .. There is some system to revive .. Some software anything .. Since connect the PDA at the base i usb of the laptop does not recognize no nothing.
Eeeeehmmmm, yes, nice. But we do not understand a word. Was it google-translated or something?
If you did something wron during upgrade, just do the upgrade again. Follow the procedure step after step, do not omit even one step - try to understand what are you doing and what for.
Without more understandable information (about what were you doing and what is happening) we cannot help you.
Stupid mistake - Serial 2.07
Reading between the lines of the original post I suspect the author has done the same as me - or at least ended up with the same result. Anybody know of a fix.
Cause; I attempted to restore from backup over wifi (yes wifi - I was desperate & didnt have the cradle available).
Result; my XDA 2s went blank and now displays a screen displaying "Serial V2.07" (or "USB V2.07" when in the cradle). No amount of re-attempting to re-connect to the device works. I'v tried soft / hard resets / battery removal etc. I'm using Microsoft ActiveSync V4.5. The XDA is an O2 badged variant.
I suspect I'm looking for a boot strap load program that will repair the xda rom such that i can subsequently reload its operating system. Any positive suggestions gratefully received.
just found reference to putting xda2s into bootloader mode "soft reset button,power button and center of D-pad button together" - this still leaves the screen saying "Serial v2.07" - Am I already in bootloader mode? - if it is what do I do next?
Fixed
problem solved - I went back to the 2nd posters answer and attmpted from the begining to install Xda_IIs_Upgrade_v140242.exe, ignoring what was on the xda screen & it worked.
I now have a functioning xda - but I still have with the problem I was trying to solve in the first place.
After a the xbackup restore, the xda desktop isnt re-written cleanly, it overlays semi-transparently on top of the last program run. The desktop accepts stylus commands to run programs which open and display cleanly. How can I clean this up - I dont want to loose O/S DBs e.g. my messages etc. - I dont see a way I can port them across upgrades so I can not just stick with the Xda_IIs_Upgrade_v140242.exe
I feel if they have not understood anything written .. I do not understand Spanish and in English .. I have the problem of serial V.2.07 screen .. Where can I download a rom for qtek9090. In my pda you do a hard reset buttons with record power + + reset and still continues to do nothing with serial on the screen .. If there is any mistake in what they write what I am using the translator google
i got the same problem ...screen saying "Serial v2.07" - Am I already in bootloader mode? - if it is what do I do next?
hate to throw my phone in the garbage can
please someone help meee
anybody found any news?
still in bootloader mode, error 112 at stage 3. BA turns off when trying to update.
2much 4me
anybody come back from this point to wm3?

MDA Problems

Hi. I am trying to unlock and flash my T-Mobile MDA, but as soon as I open and hit update on the wizard button rom the phone shuts down and then doesnt start back up to show me the beer screen. It is a G3 device and it is CID locked. SIM is also locked. Any suggestions?
i have
the same problems.
It´s a MDA from german t-mobile with G3 - so a wizard.
But i searched about 2 days but it´s not possible to get into bootloader mode. The original firmware update also is NOT working because restart in bootloader not works.
But there IS a solution that i´m trying just at this time - try ShellTool (search in Forum) and you will get lucky. The first Software update from t-mobile just worked now i´m flashing version 3.x to try.
But don´t forget to first enable RAPI on it - the easiest solution is with "Wizard Service Tool", because else you won´t have luck in updating.
And be sure to ONLY prepare a G3 phone in that way (when rebooting you can see it in the versions of IPL and SPL - if they are something like 1.06 or 2.21 or so you have luck - but 2.xx.xxxx is a G4 phone there you have to pay attention (look into forum for more infos).
After that i want to get wm6.1 on it.
If there is somebody who has an idea getting into or updating the bootloader then he is greatly welcome
And yes i tried camera button, power button, soft reset and so on - also (some people wrote down) i tried to put in USB Cable - every time i press camera and want to restart there is NO reaction of the phone until i make a new soft reset!
Thanks man. i will definitely try the shell tool out. If any one else has more suggestions that would be great!
Update: WM 6.1 is now working on it - but still with the old bootloader. I don´t now, why there is no possibility to get into it but now it´s not my problem any more
Best regards!
Stefan
Lustikus said:
the same problems.
It´s a MDA from german t-mobile with G3 - so a wizard.
But i searched about 2 days but it´s not possible to get into bootloader mode. The original firmware update also is NOT working because restart in bootloader not works.
But there IS a solution that i´m trying just at this time - try ShellTool (search in Forum) and you will get lucky. The first Software update from t-mobile just worked now i´m flashing version 3.x to try.
But don´t forget to first enable RAPI on it - the easiest solution is with "Wizard Service Tool", because else you won´t have luck in updating.
And be sure to ONLY prepare a G3 phone in that way (when rebooting you can see it in the versions of IPL and SPL - if they are something like 1.06 or 2.21 or so you have luck - but 2.xx.xxxx is a G4 phone there you have to pay attention (look into forum for more infos).
After that i want to get wm6.1 on it.
If there is somebody who has an idea getting into or updating the bootloader then he is greatly welcome
And yes i tried camera button, power button, soft reset and so on - also (some people wrote down) i tried to put in USB Cable - every time i press camera and want to restart there is NO reaction of the phone until i make a new soft reset!
Click to expand...
Click to collapse

[SOLVED] Noob needs help! Is my qtek9100 a brick?

Hi!
this is my first post here, so sorry for my bad english or mistakes
i bought a qtek 9100 on ebay, and i'm wondering if it's a brick or not. i received the device 3 days ago. during this time i read through a LOT of threads here, tried a few things and nothing works.
here is some info:
- the phone is a qtek 9100 without branding
- the IPL is now 1.01 (i flashed "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE" successfully)
- the SPL is 2.18 (because of the missing suffix ".0001" i guess it's a G3)
- GSM is 01.12.10
- OS is 1.5.4.2
- when i start the device (without any button pressed) it stops at the splash screen (which was a qtek logo before flashing, and is now this picture with a beer, that says "some things last forever" )
- i can get into bootloader screen (color screen) by holding camera button while starting
- in bootloader screen a small "USB" appears when i connect cable to usb on pc
- when i press communicate and voice buttons (on the sides) while starting, the "Press send to restore factory default" screen appears, but pressing send prints out "Format FAT Partition Format is Failed"
- the device gets recognized by windows ("Mobile Device" appears on my computer)
- ActiveSync 4.5 does not connect to device, not even as guest.
- when i hit "Connect..." in ActiveSync's connection settings, nothing is found
("Allow USB Connections" is ON)
- the device is CID-locked ("FF" state in Mtty 1.42)
- i can't unlock CID, because i can't get "EnableRapi.cab" onto the device without ActiveSync connection
Ok, these are basically the things i know now. The problem is that i never saw any other screen then the "HTC" boot screen, the "Qtek" splash logo (the one with the clouds) before i flashed with custom ruu wwe, after that i see the new splash logo, and i can get into bootloader (color) screen. I never saw any windows mobile running on this device! I could never establish a connection with ActiveSync!
So i hope that someone here on this nice forum can help me get this device to work (WM5 would even be enough right now) or at least give me a hint!
Thanks in advance!
Put the phone in bootloader mode and flash back to the original ROM.
since i bought it in ebay i don't have the original rom of this device.
but i found "233309-qtek9100_2180707_21807109_20710_qtek_ger_ship.exe" through google, which seems to be an original qtek rom (version 2.18). shall i flash this one?
You can find in the Wiki the latest official roms of every brand for our Wizards .-
ok, thanks.
i found one (Qtek GER 2.18.7) and flashed it. the process was successfull, now the IPL/SPL is both 2.18 . But the device still doesn't start and stops at the splash screen (which is now the original qtek splash again). I can still get into bootloader mode and hard reset results in "Format is failed"! No ActiveSync connection either... how should i proceed now?
i basically narrowed it down to these two problems:
- the splash screen freezes
- hard reset error "Format is failed"
( IPL: 2.18, SPL: 2.18 )
can't anybody help please?
i'm freaking out about this
With everything i’ve read the only people who’ve had any success had CID unlocked devices.
ok, i think that too for what i've read so far...
is there any other way of CID unlocking except lokiwiz (can't copy enablerapi.cab without activesync!)?
would this imei-check service that i've read about work in this case?
meanwhile i've also tried something with mtty (r2sd all) but doesn't work -> "didn't get proper security level"
is this also because of the CID lock? i tried to find out the right password to enter in mtty, but found nothing that worked...
does anybody know the correct password?
I couldent CID unluck my 9100 with lokiwiz so i did it 5min ago with Wizard Service Tool (ha to reboot my computer).
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Look up the orignal rom on the wiki, get into bootloader. And flash it back.
Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse
Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks
Like I sad before
Get into bootloader, flash back the original rom and try again.
mizobuchi said:
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks
Click to expand...
Click to collapse
I put the original rom.
But... the problem is the same.
when I started the device (without any button pressed) it stops at the splash screen (which has a qtek logo before flashing)
- i can get into bootloader screen (color screen) by holding camera button while starting, I installed the original and others rom who days before works perfectly... Now... this stopped at splash screen
- when I tryed to format.. = "Format FAT Partition Format is Failed"
Any idea?
I have tried this : http://forum.gsmhosting.com/vbb/showthread.php?t=332143
but... without success.
Could you help me, please?
Very Thanks
i'm still stuck with the same problem with hang up on qtek splash screen, too!
i have IPL 2.18 and SPL 2.18 and i can get in boot loader screen and connect with usb. (but no activesync connection!)
formatting doesn't work either.
does anybody have an idea how to solve this?? it's frustrating... i've tried almost every guide here on the forums.
same proplem here with
ipl 2.16
and spl 2.16
I used this to fix this problem
Hi i had the same problem the other week, installed a dodgy app, went to do a hard reset and wouldn't do a hard reset format failed. Tried updating rom everything worked ok until you booted it up. Wouldn't go past second splash sreen. After a few hours of trawling round i found this thread.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=format+is+failed
worked for me. Hope this helps you out.
Problem in connecting to my PC
Hey ,
I just bought a qtek 9100 a day before ... I tried to connect it with my computer.. instead of connecting my battery gets charging well can u plz help me out !
is there any software that i should install in my pc in order to get it connected to my PC...... please help me fast ! Lot of work is pending !
Thanks
Salman
Ok guys, I finally have this SOLVED.
My QTEK 9100 is working fine now!!!
I'm so happy with it right now
Since nothing I tried worked, I went to imei-check.co.uk and got my phone completly unlocked! It only cost me about 11€ and since it works now I have to admit that it was worth it (no advertising). After the unlocking was done I could do the "r2sd all"-method (Tool: MTTY 1.42) using a miniSD card. You can find a good tutorial on this board somewhere. After that everything was just fine...
-> I never saw it working and Hell Yeah: This baby just kicks a$$ !!! (although it's kinda 'oldschool' these days )

Categories

Resources