[Q] How to connect the Note to a Mac? - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

Ive been searching for a way to just connect the Note to a Mac via USB to have access to the camera and file system to grab some movies but can't find any solutions. I enable mass storage under settings but the Mac ignores it. Any ideas?

Hello,
i don't have any issue on my side, although i use different mac.
Have you tried to use "system_profiler SPUSBDataType" in the Terminal app ? It gives you information on linked usb devices of your mac. Does your phone appear ? What appear in the system profiler ?
Also, you can access your phone files from your mac over wifi, using Kies (installed by default on the Note) or airdroid (which i prefer personally).

goconfigure73 said:
Ive been searching for a way to just connect the Note to a Mac via USB to have access to the camera and file system to grab some movies but can't find any solutions. I enable mass storage under settings but the Mac ignores it. Any ideas?
Click to expand...
Click to collapse
Plug into your Mac. If unknown network notification appears on your Mac cancel network connection. Tap on USB connect in the notification bar on the Note and say yes when it asks if you wish to USB connect. Your external and internal SB cards will appear on the Mac as no name folders.
Alternatively you can download Kies here: http://www.samsung.com/uk/support/usefulsoftware/KIES/JSP
To use Kies after downloading and installing, turn USB settings, plug into the Mac and tap Kies connection when prompted in the notification bar.

Related

[Q] PC not recognizing USB?

Anyone else having problems with your PC not recognizing the phone? Even after selecting mass storage in the usb settings, when i plug the phone in to the PC the little usb notification in the notification isn't showing up.
donwonlee said:
Anyone else having problems with your PC not recognizing the phone? Even after selecting mass storage in the usb settings, when i plug the phone in to the PC the little usb notification in the notification isn't showing up.
Click to expand...
Click to collapse
Have you installed the Samsung drivers?
yeah i've tried installing the drivers. the phone isn't even putting the usb icon in the notification tray anymore. just starts charging and that's it. i go to usb settings/mass storage and nothing. any ideas?
I got that too, I just put the usb cable in another usb port on my computer and tadaaaa: problem fixed
I had this issue and read in a forum (not sure where wish I did to give credit) where u need to format your internal SD memory (the built in 16 gig SD) I did that and it started to work again.
Sent from my SAMSUNG-SGH-I897 using XDA App
donwonlee said:
Anyone else having problems with your PC not recognizing the phone? Even after selecting mass storage in the usb settings, when i plug the phone in to the PC the little usb notification in the notification isn't showing up.
Click to expand...
Click to collapse
How about Menu > settings > applications > usb settings > ask on connection.....
Palmetto_X said:
How about Menu > settings > applications > usb settings > ask on connection.....
Click to expand...
Click to collapse
I had/have this problem sometimes too. choosing "ask on connection" usually works. I find that if you select anything other than "mass storage" then exit out, then go back in and choose mass storage, it works again.
Usually only have to do it once after a factory reset or on a new phone
I find my connection to be hit or miss. The pc picks up the drivers fine but doesn't mount the phone as a drive. Kies is a pain to get going too. I read on here that you need .net framework 4 and also no file names over 16 characters, and without kies I think you need to be in debug mode on application settings. I still need to try the short file names and see if it improve it but I never really hook up to a pc anyway, my father has win 7 and I have kies on his computer. I have linux mint 9 on my own so I rarely get to fitz with it on a windows machine.
Sent from my SAMSUNG-SGH-I897 using Tapatalk
I'm having this problem, can't get usb debugging mode to turn off. It immediately turns on when I turn it off. It's as the just says, "yeah, you can uncheck it, but I'm gonna leave it on."

[SOLVED]Galaxy Tab doesn't display when connected to PC via mass storage

My Galaxy Tab when connected to PC via Samsung KIES runs fine... but when I connect it as Mass Storage, it doesn't show up in My Computer... I even tried re-flashing the TAB again to overcome kratos and the default stock rom... to no avail... need help...
To make things a bit clearer, here's the setup...
USB Debugging set to OFF / PC running Windows 7
USB Settings set to SAMSUNG KIES
PC detects the TAB as GT-P1000 and I can access the internal storage... though a tad bit slow when transferring data & stuff...
USB Settings set to MASS STORAGE
PC detects the TAB -> TAB displays USB Connected -> press CONNECT USB STORAGE
PC detects TAB as Android UMS Composite USB Device -> note without drive letter
After sometime, I've finally found the culprit... here's my solution:
#1 - Set USB Settings to MASS STORAGE -> Connect TAB -> PC detects TAB but doesn't show TAB as USB Device
#2 - run the program diskmgmt.msc via Windows Start Button->Run->diskmgmt.msc
#3 - Disk Management loads all detected hard drives & USB media... saw my TAB's icon without the drive letter... (it seems Win7 had a hard time assigning one, maybe because I've got lots of USB drives)
#4 - Right-click on the TAB's icon and on the context menu choose -> Change Drive Letter and Paths...
#5 - Simply assign a drive letter and voila! Your TAB's detected again as USB Mass Storage
When you try to use mass storage do you go into menu, settings, wireless and network, usb settings, and change it to mass storage?
Sent From Githrog's Tab
yes... it was working fine the last time I've connected the TAB as usb mass storage... but after the next time... it was no longer displaying on my computer...
same here.. using kratos overcome ROM.. my laptop detects the said removable devices but when i double click on it, it says it needs to be formatted.. =/
I am not sure if this will work, but see if USB debugging is on. If so, turn it off.
Sent from my SCH-I800 using XDA App
Already tried both, but to no avail... what could be the problem..?
Same to me and now I am back to the stock ROM though still no USB charging as original
icarusjun said:
My Galaxy Tab when connected to PC via Samsung KIES runs fine... but when I connect it as Mass Storage, it doesn't show up in My Computer... I even tried re-flashing the TAB again to overcome kratos and the default stock rom... to no avail... need help...
To make things a bit clearer, here's the setup...
USB Debugging set to OFF / PC running Windows 7
USB Settings set to SAMSUNG KIES
PC detects the TAB as GT-P1000 and I can access the internal storage... though a tad bit slow when transferring data & stuff...
USB Settings set to MASS STORAGE
PC detects the TAB -> TAB displays USB Connected -> press CONNECT USB STORAGE
PC detects TAB as Android UMS Composite USB Device -> note without drive letter
After sometime, I've finally found the culprit... here's my solution:
#1 - Set USB Settings to MASS STORAGE -> Connect TAB -> PC detects TAB but doesn't show TAB as USB Device
#2 - run the program diskmgmt.msc via Windows Start Button->Run->diskmgmt.msc
#3 - Disk Management loads all detected hard drives & USB media... saw my TAB's icon without the drive letter... (it seems Win7 had a hard time assigning one, maybe because I've got lots of USB drives)
#4 - Right-click on the TAB's icon and on the context menu choose -> Change Drive Letter and Paths...
#5 - Simply assign a drive letter and voila! Your TAB's detected again as USB Mass Storage
Click to expand...
Click to collapse
That is fantastic, now I know how to fix this problem if it should ever arise for me, once I get my new laptop of course... my current pc is running xp so im not sure if this would be the same presedure to fix. Very nice explanation
Sent from Githrog's Charm

nc not appearing in pc

Tried in stock, cm7, different usb ports, win7, winxp, reboot nc but no joy. My nc wont appear or get detected by my pc.
All I want is to transfer files from pc to nc
Did you click the button in your status bar to enable USB mode?
---------------------------------
Sent from my LG Optimus V using Tapatalk
which one is that? how will I enable usb mode?
is it the one with wifi, bt, gps, volume icon with the No notification?
how to copy movies and pdf using card reader?
When you plug into the PC, two extra notification icons should appear in the bottom status bar. If these do not appear then ignore the following, if they do appear then...
Pull the status bar up (with the round icon with the green up arrow or touch and drag up), then select the gray text that says "Select to copy files to/from your computer" You should see a little android guy with one button below him saying "click to turn on file transfer" or some such. Then it should show up as a drive on your PC.
there is no notification icons that appear in the status bar near clock and batt...
It says "No notifications" too in wifi bt crosshair volume bar...
I have the same problem with my nc not showing up...
Can not connect to PC with USB. Using SD to boot to the CM7.
Have not found anything regarding the USB mode.
Where is it?
on your OC... Nook NOT connected....
Go into device manager...
View... check "Show hidden devices"
Under Android Phone... delete "Android Composite ADB Interface"
Under Disk Drives.... delete any drives that are "B&N Ebook Disk USB Device"
Under Portable Devices... delete any drevices that are not currently connected
Under Universal Serial Bus controllers...
select each device that is not a "Universal Host Controller" or is not OBVIOUSLY not nook related (i.e. "Apple ...." or "Generic USB Hub" or "SAMSUNG..." etc...
Check the properties of the device... on the "Details" tab... select "Hardware Ids".... delete any that are "USB\VID_2080...."
Install the drivers then connect the Nook
I actually had this problem for quite a while. Check the microUSB connector on your cable, if it's even a little bit loose, you may need to replace it. Just call B&N up and ask for a replacement, they should give you a free one.
DizzyDen said:
on your OC... Nook NOT connected....
Go into device manager...
View... check "Show hidden devices"
Under Android Phone... delete "Android Composite ADB Interface"
Under Disk Drives.... delete any drives that are "B&N Ebook Disk USB Device"
Under Portable Devices... delete any drevices that are not currently connected
Under Universal Serial Bus controllers...
select each device that is not a "Universal Host Controller" or is not OBVIOUSLY not nook related (i.e. "Apple ...." or "Generic USB Hub" or "SAMSUNG..." etc...
Check the properties of the device... on the "Details" tab... select "Hardware Ids".... delete any that are "USB\VID_2080...."
Install the drivers then connect the Nook
Click to expand...
Click to collapse
check everything in device manager but found none of the above.
alunral said:
I actually had this problem for quite a while. Check the microUSB connector on your cable, if it's even a little bit loose, you may need to replace it. Just call B&N up and ask for a replacement, they should give you a free one.
Click to expand...
Click to collapse
its charging and its not bit loose but can't even get detected, not appearing in my pc, and no message from both nc and pc using stock firmware.
You could check MyPhoneExplorer from http://www.fjsoft.at/en/
Should work on CM7 with USB and WiFi.
WalangAlam said:
check everything in device manager but found none of the above.
Click to expand...
Click to collapse
Then install the drivers and connect Nook to computer... also as mentioned above check your cable... you can also try a standard uUSB cable and not the nook cable.
WalangA, are you still having problem or being solved? Let me know, I might able to help.
Also, pls tell us you're running CM7 from where? eMMC or uSD.
If you have home wifi, here's another option: go to the market and download WiFi File Transfer. Start Wifi File Transfer on your Nook and it will give you a number (something like 192.168.1.3:1234). Open a browser on your desktop and put whatever number shows on the NC into the location of your browser. You can then move files back and forth - no usb cable needed.
votinh said:
WalangA, are you still having problem or being solved? Let me know, I might able to help.
Also, pls tell us you're running CM7 from where? eMMC or uSD.
Click to expand...
Click to collapse
yes. booting fro uSD. I tried to use stock firmware too but no joy.
I'll try to manually install driver and look for normal usb too.

[Q] How to change USB connection mode?

How can i change USB connection mode for the Note? Everytime I connect the USB cable, Note always connect in MPT mode even with the MHL adapter. Help pleaseeeeeee
usb debugging
go to menu/settings/applications/development on phone then put a checked mark in the box for usb debugging. when you connect to your computer your phone will beep letting you know it has been connected to a usb source. use pull down screen touch the usb connected message and then touch the connect usb storage button. the little green guy turns orange and now your phone will show up on your computer as an extra drive. from here you can just drag and drop files to the phones directory just like a usb pen drive. i believe this is what you where asking about. hope it helps.
note: first time connecting your computer it will probably install a new device driver and also if you are using Kies you need to turn off debugging before Kies can see the phone.
First off, makes sure you install latest version of Samsung Kies, which includes USB driver for the Note.
Also there is setting to connect mass storage mode manually: Settings -> Wireless and network -> USB utilities. But it seems to be the same as just choosing to connect from the notification bar and wants you to disable debugging.
eksasol said:
First off, makes sure you install latest version of Samsung Kies, which includes USB driver for the Note.
Also there is setting to connect mass storage mode manually: Settings -> Wireless and network -> USB utilities. But it seems to be the same as just choosing to connect from the notification bar and wants you to disable debugging.
Click to expand...
Click to collapse
How to connect SGN in Kies Mode?
Whenever i Connect it to PC MTP connection is automatically initiates, My Kies Detects the phone but whenever i try to Upgrade its firmware to 2.3.6, it crashes and says FirmwareUpdate Stopped working ! I have windows 7 64 bit.
katyarevishal said:
How to connect SGN in Kies Mode?
Whenever i Connect it to PC MTP connection is automatically initiates, My Kies Detects the phone but whenever i try to Upgrade its firmware to 2.3.6, it crashes and says FirmwareUpdate Stopped working ! I have windows 7 64 bit.
Click to expand...
Click to collapse
I am facing similar issue, Windows7-32 bit, when connect SGN via USB (MTP) for firmware upgrade but not sure about 'Kies Mode', few other people got firmware upgraded successfully so i think it's something else. see this link http://forum.xda-developers.com/showthread.php?t=1318734&page=59.
In the notifications bar at the top of your screen. You will see a usb symbol in that bar. 3) Use your finger and pull down the bar and then tap the usb symbol. There you will see the option to chang it from MTP mode to any other mode option it has.
I hope this helps.
Ares7425

Transfer Files From Mac to ATT Tab

Hey guys, sorry again if this has been asked before,
How do I transfer a file from my Mac to the ATT Tab?
There seems to be no USB option on the Tab and the Tab wont mount on my desktop.
Kies don't support Mac file transfer.
Thanks
I use WiFi File Explorer PRO. Seems to be much faster than USB and it should work on your mac.
or use airdroid.
i forgot how to use usb when i used airdroid.
Honeycomb, on this tablet, doesn't use USB mass storage because there is no SD card. It uses MTP storage. It is functional but has some issues. Just use the USB charging cable from your charger and connect the tablet to the computer. make sure usb debugging is turn off unless you want to attempt to use abd to push the files.
You can get wifi file explorer, a free app that will attempt to connect the tablet to the computer via wifi.
Another option is a file sharing service like dropbox or sugarsync
http://db.tt/1v0BC1VS
these let you upload files to a cloud server. Then install them to any device with internet access. The starting point is 2GB but you can't expand that. If you want to go the route of dropbox, that link will give us both a little extra space
Thanks, I found that WiFi Pro app and it works fine.
I also just bought the G-Tab 7.7 so will be returning the 8.9 anyway.
http://www.android.com/filetransfer/

Categories

Resources