In dell streak charging port have two rectagle piece of plastic right? Two of them have been broken. Another piece stuck inside my charger port, i still can charge as usual eventhough two of the pins have already broken. Why? Does it under warranty?
Probably you had a defective device or chances are that you did not insert the cable correctly and broke the pins. The charging port is really delicate if you need to re-solder it. Thing is, if you are not used to soldering delicate parts in a mobile device, chances are high that you would break something else while resoldering. Sell your faulty Streak and buy another second hand one - they are pretty cheap now (150-300usd + shipping on ebay depending on the condition. The cheaper it is, the more scrathes it has usually.). It's better to have a full functionning device than one that will soon stop functioning when you will have trouble connecting the pins together!! Better sell it in my opinion.
It cannot be repaired?
If you know someone who can repair Dell Streaks, then ask them. otherwise......
Damage to the charging port most likely will not be covered under any warranty, whether the carrier's warranty or Dell's. The cost of such a repair would likely approach the cost of a new Streak itself. Dell themselves never bothered actually repairing the Streak, sending out refurbished or new units as replacements.
Final5k's advice is sound. Purchasing a used Streak and then selling yours for parts is the way to go here.
oMG it is really bad. I think the pin gradually be broken 1 by 1 as u said the pins are very delicate. I dun wish to sell my streak. Tomorrow i will try to contact dell.
Perhaps this is the last way to fix it?
http://forum.xda-developers.com/showthread.php?t=1392360
LOL if i chosen the last way, my streak would look very different.
Is this the item i am looking for?
http://www.ebay.com/itm/USB-Charger...Accessories&hash=item1e691b124a#ht_1606wt_952
You will probably do more harm to your device if you are a novice in dismantling phones and soldering parts. The removal of the Streak's housing is itself a pain if you are not careful enough. Where did you buy your phone?
The parts on ebay are usually non original ones as only Dell sells replacement parts. Again using non original parts might bring more problems to your phone.
But the choice is yours, if you want to venture on repairing your phone yourself, just be very careful not to damage other parts as you may end up with an unrepairable phone which you won't be able to sell to anyone.
Something similar happened to me and I just used a fine pair of tweezers and a safety pin to get the plastic out and straighten the pins and now it works fine. One of the pins is broken in my phone but it still charges fine and can connect to the pc fine.
u got the plastic out? I have two broken pin, but cant said it already broken, it just fold inside. I still able to use. Is the pin is the matter of charging speed?
Related
So i took off my siedo case just to clean the dirt and other stuff between the case and my kaiser (which i do about once a week) and i noticed that my mini USB port on my device is CRACKED!!
I didn't buy the warranty the ebay seller offered me from SquareTrade, its an ATT Tilt, so do u think ATT would honor the warranty?
This is the best pic i could get using my brother N82...
Any chance that happened while trying to blindly reach the reset hole with the stylus?
Very common mistake!
Just try to bend it upward (carefully) with a plastic or wood toothpick or something like that and it should be ready to go. Don't use a metallic object.
Good luck!
Rayan
fone_fanatic said:
So i took off my siedo case just to clean the dirt and other stuff between the case and my kaiser (which i do about once a week) and i noticed that my mini USB port on my device is CRACKED!!
I didn't buy the warranty the ebay seller offered me from SquareTrade, its an ATT Tilt, so do u think ATT would honor the warranty?
This is the best pic i could get using my brother N82...
Click to expand...
Click to collapse
at&t specifically states that warranty is extended only to the original purchaser. Was the phone ever used prior to your receipt? If not them you can probably get by if you play dumb about the original pruchase date as all Tilts are still within the 12 month purchase whindow.
i bought it on ebay for $400 with $30 dollar shipping and it was stated "LNIB" like new in box. But what was funny was when i recieved it the imei on the device doesn't match the one on the box so either could be some funny business or a refurb device with a new box.
anyways after i posted this i was sitting in the library and i used a mechanical pencil with the led sticking out to push it back to place. It's syncing with activesync sporadically, will work then won't work, don't know if its do to this crack or my activesync could be busted (running windows through fusion on a mac)
Its charging fine right now and you can barely tell its cracked, other than one of the metal pins sticking out, i tried to push it back in with the led but the led kept breaking.
I think what caused it was the other day i was driving and had TomTom going and i plugged it into the car charger and put it in my center console. Theres a little edge on both sides of the center console and the charger was resting on it so i think thats what caused it.
If it does completely break off, I can definitely play the retarded stubborn customer and harass ATT till they fix it, I've got experience with these kinda things
Kyphur this happened to me yesterday also, but the whole piece came off... so the pins are hanging in the air... but im still able to synchronized and charge it.
do you think att will honor this one too?
i also cracked mine recently, when i pushed the stylus into the wrong hole =P
i managed to push the thing back into shape gently, and it would charge with the charger and sync with the supplied cable, but i found that it wouldn't sync with my retractable 3rd party cable, and also that if i tried copying files to/from the miniSD card with the supplied cable, the files and the card would become corrupted. this may have been because i used a screwdriver to push it back into shape...
anyway in the end i had to send it and for whatever reason, the service center kept on sending it back saying it "worked", even though when it came back neither my laptop nor the computers at the store i bought it from could even recognize the device. finally at the 3rd sending back they replaced the motherboard and now it works again.
So the microUSB port on my Captivate stopped working the other day (can't connect to pc or charge without applying significant pressure in a certain direction) and I'm thinking about fixing it my self.
I'm really just looking for some advice from people who have done this before. What kind of soldering gun should I get (or will the Radio Shack special work)? What kind of soldier should I use? And should I think about buying a new micoUSB port from one of these parts stores?
Thanks in advance!
I wouldn't fix it myself...there is more to it then you think
kusanagisan18 said:
So the microUSB port on my Captivate stopped working the other day (can't connect to pc or charge without applying significant pressure in a certain direction) and I'm thinking about fixing it my self.
I'm really just looking for some advice from people who have done this before. What kind of soldering gun should I get (or will the Radio Shack special work)? What kind of soldier should I use? And should I think about buying a new micoUSB port from one of these parts stores?
Thanks in advance!
Click to expand...
Click to collapse
I'd stay away from radioshack soldering irons. I bought a cheap $30 Weller iron and it is way better. The repair is not horribly hard. The worst part is removing the bad one without lifting a pad. I lifted a pad on one I tried fixing and screwed up one of the pads and a tiny bit of the trace. Needless to say I could not fix the tiny damaged trace and sold it off for parts. But the new usb went on without a hitch with some good solder and some desoldering braid.
I offer this repair as a service and for way cheaper than ruining your board...
PM Sent...
chrislj said:
I'd stay away from radioshack soldering irons. I bought a cheap $30 Weller iron and it is way better. The repair is not horribly hard. The worst part is removing the bad one without lifting a pad. I lifted a pad on one I tried fixing and screwed up one of the pads and a tiny bit of the trace. Needless to say I could not fix the tiny damaged trace and sold it off for parts. But the new usb went on without a hitch with some good solder and some desoldering braid.
Click to expand...
Click to collapse
Do you think it's possible to fix it without replacing it? IE Just apply more solder or try to re-solder the current contacts?
connexion2005 said:
I offer this repair as a service and for way cheaper than ruining your board...
PM Sent...
Click to expand...
Click to collapse
I'll probably end up using your service if this is over my head, thanks for the link!
kusanagisan18 said:
Do you think it's possible to fix it without replacing it? IE Just apply more solder or try to re-solder the current contacts?
I'll probably end up using your service if this is over my head, thanks for the link!
Click to expand...
Click to collapse
It's virtually NEVER the connection between the leg and pad that is the issue, but rather always the inner connector that touches with the pins on the USB cable itself. So basically no, re-flowing the legs to pads won't do anything. I always ohm through the leg to the pad before replacing them to check if it's an easy fix but that's never the case and the whole connector ends up being replaced...
Download Jig Works But Won't Charge/Connect USB
I think I am having the same problem. I can use a download jig that I got from MobleTech some time ago, but the USB will only connect if I fiddle with the connection and will drop out almost immediately. I first noticed it because the phone was not charging overnight. I was running teamhacksburg ICS and thought I had developed the charge bug, but appears that I might need a new USB connection. Have tried differn't computers with same results. Is it safe to say I need a new USB port for my Captivate or are there some other things I should check. Thanks for the help.
If it's finicky like that then yes almost certainly.
So how would you go about replacing your USB port on your Captivate? or is it not worth trying for most people? One of the pins on my port came loose and got smashed to the outside shell. In trying to bend it back, it broke of course. So now no Download mode from Jig and no computer recognition.
connexion2005 said:
I offer this repair as a service and for way cheaper than ruining your board...
PM Sent...
Click to expand...
Click to collapse
I am having the same problem. Could I get a PM or a link to your repair?
YzRacer said:
I am having the same problem. Could I get a PM or a link to your repair?
Click to expand...
Click to collapse
Could I also get the link?
sebastienhwb said:
Could I also get the link?
Click to expand...
Click to collapse
I never got a PM but I followed the clues over to mobiletechvidoes. Once you add usb repair to your cart and check out you will receive an email about sending in the phone (after an hour or so) and I have just sent one in. It says send the phone without a battery or battery cover and I went ahead and wiped the phone just for safety.
Anyone ever find the link or know how much this costs?
in my sig if i remember correctly it is about $35
I paid $35 and it worked out well for me! Mobiletechvideos.com is where I signed up and they were fast and professional.
Fixed with vice grips
Just did this and slowly applied a little pressure and adjusted for more pressure at the end of the USB metal connection. It's a sturdy fit now and I'm not losing connectivity.
So the fix is to replace the connector altogether? Does anyone have a digikey part # or equivalent?
My issue seems to be that it charges, but I have no data connection. The pins don't need a reflow. Unfortunately, I don't have a spare micro usb cable to splice and check continuity on hand.
Is there any way I can talk with the enumerator chip to make sure it isn't fried, or should I just do the continuity check?
hi
I have the same problem, i searched on sites how to change it your self, but i couldn't find anything
Just check his signature.
http://mobiletechvideos.mybigcommerce.com/
other stuff available from them too. i am a past customer. they saved my cappy
MICRO USB
Anyone else had the USB port become mildly loose (moves back and forth if any pressure is put on the cable)? I believe its on its way out.
Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
KillerbawX said:
Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
Click to expand...
Click to collapse
You could probably buy two new Raiders for $250! Replacement might be the best bet, as you can likely find one on Kijiji for $100 or so. If you have a local cell repair joint, give them a call, and see if they offer the replacement. It might be tricky since the USB on the Raider (as other HTC phones) is actually a special type of HDMI jack that also has USB (known as MHL).
If you're adventurous, you might track down a broken Raider and attempt a part swap yourself. I've not seen the inside of the unit, so I can't say how easy or hard that would be at any skill level...
Hope you get it fixed up!
The part is on eBay you can always try to do it yourself should be a few small solder points
Sent from my HTC PH39100 using xda premium
KillerbawX said:
Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
Click to expand...
Click to collapse
A friend needed this. We ordered one off ebay ( http://www.ebay.com/itm/OEM-USB-Pow...328529?pt=PDA_Accessories&hash=item27c422a1d1 ) and although it required opening the phone up and voiding the warranty, it required no soldering. He doesn't open electronics up very often, and said it wasn't very hard to do.
i was babbling abt this in a thread in the dev forum, thot i'd best do it also here in the proper forum for it:
i changed the USB port in my Raider, was very simple. Six little screws, two different lengths so keep track of them. One screw also holds down the teeny cover under which is where the tiny connector resides that connects the port to the fone circuit board. Once the fone is back together that's where you make the final connection between port and fone.
Slip off the battery cover, undo the six screws, take off that tiny little cover. Carefully work off the entire back housing. There's no front housing, just the screen glass and the fone circuitry bundled together.
Micro-USB port and ribbon connector is fastened to the housing with two more of those little screws. Change out the port with the new one. New part may not be an exact duplicate of the old part: that's ok. Reassemble the fone. Under that hole left by the tiny cover, press home the miniscule plug that connects up the port to the fone.
Put back the tiny cover, fasten back all the screws, and you're done. Port cost me $9 USD plus shipping on ebay.
lowfatmilk said:
i was babbling abt this in a thread in the dev forum, thot i'd best do it also here in the proper forum for it:
i changed the USB port in my Raider, was very simple. Six little screws, two different lengths so keep track of them. One screw also holds down the teeny cover under which is where the tiny connector resides that connects the port to the fone circuit board. Once the fone is back together that's where you make the final connection between port and fone.
Slip off the battery cover, undo the six screws, take off that tiny little cover. Carefully work off the entire back housing. There's no front housing, just the screen glass and the fone circuitry bundled together.
Micro-USB port and ribbon connector is fastened to the housing with two more of those little screws. Change out the port with the new one. New part may not be an exact duplicate of the old part: that's ok. Reassemble the fone. Under that hole left by the tiny cover, press home the miniscule plug that connects up the port to the fone.
Put back the tiny cover, fasten back all the screws, and you're done. Port cost me $9 USD plus shipping on ebay.
Click to expand...
Click to collapse
Hey, dude, I know this thread is a little old, but can you PM me the link to where you bought your USB port? I think I need to replace my port (issues connecting to PC and charging requires wire wiggling), but I've read about certain ports not working with data transfer and only charging, and I don't want to make that kind of mistake.
projectisaac said:
Hey, dude, I know this thread is a little old, but can you PM me the link to where you bought your USB port? I think I need to replace my port (issues connecting to PC and charging requires wire wiggling), but I've read about certain ports not working with data transfer and only charging, and I don't want to make that kind of mistake.
Click to expand...
Click to collapse
Try this? Says OEM so I imagine you wont lose functionality.
http://www.globaldirectparts.com/product-p/htc747235-qs.htm
Thank you! And only $8 too
Sent from my Vivid 4G using xda app-developers app
Hello,
I don't know if this is the right place where to ask,but I wanna try to ask here. One of my friend two years ago bought the "samsung galaxy s6 edge". Now the battery is broken and he should find a on line place to change it with a new battery,without to pay a big amount of money to make the operation. Do you know where he could go ? He tried to go in local shops but they asked to him a lot of money. Take also in consideration that it is a relatively easy operation to do...thanks
If the battery is swollen, or the phone looks fat, other components may have already been damaged. Do -not- try to charge it. Buy the correct official battery (one that has been very recently manufactured and the two adhesive strips if not already included), the adhesive layer for the back glass (or a brand new back glass with adhesive already attached) and do it yourself.
It is not simple. You must do research, don't rush things and even then you risk breaking the back glass, wireless charging pad, main board, OLED display/digitizer/front glass (while removing battery due to the adhesive), various ribbon cables, connectors and other parts. It is the only way to potentially save money (but not time). Videos are here. You will also want to test functionality of the USB port and wireless charging pad.
Otherwise, contact Samsung directly and send it in.
marietto2008 said:
Hello,
I don't know if this is the right place where to ask,but I wanna try to ask here. One of my friend two years ago bought the "samsung galaxy s6 edge". Now the battery is broken and he should find a on line place to change it with a new battery,without to pay a big amount of money to make the operation. Do you know where he could go ? He tried to go in local shops but they asked to him a lot of money. Take also in consideration that it is a relatively easy operation to do...thanks
Click to expand...
Click to collapse
I'm not sure if this is relevant but it took me 15 minutes with a suction cup and a Phillips 00 screwdriver and a $10 oem new battery. Just buy a new back glass for another $10 if you dont want to be careful with it. Check ebay. I swear its not that hard just take your time once it's open to not break cables.
Pretty much like the title says, looking for a place to buy the N10 pogo cable. I know the tablet is a relic at this point, but it still does what I use it for just fine (mostly youtube/twitch), and the usb connector is dying. If you're selling, or know of a place to buy one, please let me know! As far as I can tell it's not available anywhere anymore.
My wife still uses her N10 with pogo cable. I'll be sure to offer it up here whenever that time comes.
I still check ebay and google every so often to see if for some reason they go back on sale (ya never know when someone might find a box of them in a warehouse somewhere), but I never turn up anything sadly. Someday maybe...
Diet6 said:
I still check ebay and google every so often to see if for some reason they go back on sale (ya never know when someone might find a box of them in a warehouse somewhere), but I never turn up anything sadly. Someday maybe...
Click to expand...
Click to collapse
Good luck. I actually contacted some cable manufacturers in China a while back interested in a group buy type thing but they informed me it would be around $15k USD just for tooling alone and then there would be a minimum order of a couple thousand units.
Hasn't someone reverse engineered it and just 3d printed a connector casing?
With my non existent engineering experience I see it as chopping the end off a USB cable and soldering the wire to little copper contacts.
So soldering is fiddly and flush mounting the contacts will require a modicum of precision. To an experienced enthusiast that has to take less than five minutes.
The 3d print can be rough with a tiny bit of hand finishing.
Little magnets...
made for £($)5 sold for £($)15?
Are there enough manta owners?
olly230 said:
Hasn't someone reverse engineered it and just 3d printed a connector casing?
With my non existent engineering experience I see it as chopping the end off a USB cable and soldering the wire to little copper contacts.
Click to expand...
Click to collapse
It's not as simple as that. If you just solder off the end of usb, it will still charge at 5V.
The Pogo cable has more than 4pins that standard micro USB cables use, and we need 2 more pins for who-knows-what-for.
This is why most of us still don't have a pogo cable, even though it looks simple enough.