Database Develop

[Q] Big problems with my Galaxy....Help needed!!

Since yesterday my Galaxy S got stuck. It doesnt start anymore.
What happened?
I flashed my rom to the newest ICS. Everything went well and I used it a couple of days. Yesterdaymorning I did wiped the battery stats and cleared the Davik cache. I rebooted and it got stuck in the bootscreen.
I tried to got in recoverymodus but that was not possible. Bootscreen was all I saw.
Then I tried the downloadme. That is working BUT odin did not see my phone and KIES did also not recognize it. I have the right drivers. When my phone was working it was also not recognized because I am afraid the USB port is not good anymore.
Does anyone have tips?

wvawijk said:
Since yesterday my Galaxy S got stuck. It doesnt start anymore.
What happened?
I flashed my rom to the newest ICS. Everything went well and I used it a couple of days. Yesterdaymorning I did wiped the battery stats and cleared the Davik cache. I rebooted and it got stuck in the bootscreen.
I tried to got in recoverymodus but that was not possible. Bootscreen was all I saw.
Then I tried the downloadme. That is working BUT odin did not see my phone and KIES did also not recognize it. I have the right drivers. When my phone was working it was also not recognized because I am afraid the USB port is not good anymore.
Does anyone have tips?
Click to expand...
Click to collapse
can you go to recovery?

unfortunately not.
if i do the 3button trick the sreens stays on the bootscreen.

Change your drivers to the Nexus drivers in OP of TH ICS thread and try a different USB port.
Once in odin flash the initial CM7 kernel without reboot then go into recovery and reflash CM9.

installed nexusdrivers.
still nothing happens.
any other suggestions?
thx for the help!!!

Different USB port?

tried all 4 and another laptop
also used different cables.
almost start crying

-prereq-
install samsung drivers for your device and windows install type (x32/x64). It's quite important that you install 64 bit drivers on a 64 bit box and not 32, because they are ****ty and work 7/10 times used.
1. be sure to use the same port.
2. be sure to use ONLY the original cable that came with your phone
3. Make sure your phone is able to enter download mode. (Vol down+Home+Power)
if it does, it should install your drivers without issue about then.
4. If you can't use odin to restore your pda/csc/modem, then use heimdall. If that fails, you need to commandprompt heimdall into flashing with 512.pit + required files (refer for help to the heimdall readme included in their install) file after unpacking pda,modem,csc into the heimdall commandline exe.
If 4 does not work you need to unbrick it via 1clickbrick. It's a jar file you donwnload, dblclick and use.

thx for trying to help me. but I am afraid my USB port (mini) on my galaxy is not working. Tried 4 computers, several drivers but stil no connection possible.
Any other suggestions?

wvawijk said:
thx for trying to help me. but I am afraid my USB port (mini) on my galaxy is not working. Tried 4 computers, several drivers but stil no connection possible.
Any other suggestions?
Click to expand...
Click to collapse
Did you indtall usb drivers?
Sent from my GT-I9000 using XDA App

Try flashing the EZBase with Odin in Download Mode. Then report back
Sent from my GT-I9000 using Tapatalk

thx but the problem is : odin does not work.... it does not recognize my phone.... and I use the right drivers....
can it be because I work on isc rom?

When i was on ics (bootloop), ich have downloaded the Samsung USB drivers (exe.) and flashed via odin jvu...
Sent from my GT-I9000 using XDA App

@ aakaashjois
damn....it didn't work with the EZbase pitfile.....:-(

Unusual
wvawijk said:
@ aakaashjois
damn....it didn't work with the EZbase pitfile.....:-(
Click to expand...
Click to collapse
Are you sure? did your phone appear as 'added' after you out it in d/l mode? follow these steps...this is a sureshot method dude.
http://www.theandroidsoul.com/ezbase-ezrom-for-android-2-2-install-revert-back/
Good Luck!

any of the computers find it as new hardware?

amadeus_l said:
Are you sure? did your phone appear as 'added' after you out it in d/l mode? follow these steps...this is a sureshot method dude.
http://www.theandroidsoul.com/ezbase-ezrom-for-android-2-2-install-revert-back/
Good Luck!
Click to expand...
Click to collapse
No added unfortunately..... starting to give up.......

hackandmore said:
any of the computers find it as new hardware?
Click to expand...
Click to collapse
Nope..... I am afraid I lost my Galaxy...... :-(

Had the same problem on Windows machines - for some reason two of my Windows powered computers stopped recognizing my phone. Tried different drivers for no effect, so I gave up and tried it on linux and successfully flashed new kernel using heimdall.
I don't know if this is a legitimate solution because it's like going around the problem instead of solving it, but if everything else fails, try different operating systems.

try charging it..does it charge?
if it doesnt then go in a service and ask them to take a look at it.they will do that for a pack of cigarettes in their extra time.if its fixable and cheap(dont think of replacing the entire motherboard...sell this one for parts and buy another one, or find one with broken display and take em both to a service and tell them to replace the screen from your phone to the other)

[Q] Boot loop without recovery and download mode

Hello everybody!
I've tried to find a solution, but without success.
Today I tried to install CWM on a french Galaxy S.
I've rooted the phone with z4root and after I started on download mod with adb.
Then with Odin3 I installed this file "Root-XX_OXA_JVK-v2.7-CWM3RFS.tar".
After that the phone rebooted automatically, unfortunately it's rebooting eachtime on the galaxy s logo.
The problem are that I can't boot on download mod or on CWM.
When the phone is off and I plug it on charger, it doesn't charge!
I think my phone is bricked.
Do you think you can help me or it's dead?
Is there a hard reboot procedure or something like that?
Thanks

I have exactly the same problem!

Are you sure you can't enter recovery? Volume up+home+power.
Sent from my GT-I9001 using xda premium

Yes i'm 1000% sure!
I can acess the Download Mode, but Odin/Heimdall does not recognize the USB connection...

Keep Trying
I know this is weird but keep hard resetting it. Try like 20 more times before you give up. Worked for me in the past I know it is weird. I had just flashed a new factory ROM.

I swear i have tried to enter the Recovery 20-30 times!!

It's fine
Hello,
I've bought an USB JIG for my SGS GT i9100 and I've been able to install ICS SLIM using Odin v3 1.7.
Very easy...
I advise this solution..
Thanks for your help.

Italia99 said:
I swear i have tried to enter the Recovery 20-30 times!!
Click to expand...
Click to collapse
did u try vol down + home + power button to go to download mode? if it can do that, the problem is just find some driver to make odin recognize your phone. search for "usb driver for samsung galaxy s" in google
then you can bring back your phone to live by downloading any rom you want and flash it via odin
ps. but if you cannot go to download mode, JIG USB with 301 K ohm will help you look at http://www.youtube.com/watch?v=Rdn5GoRjhn0

Same problem here, I actually didn't see this in my search and made a new thread about it (feel free to delete). My computer had KIES on it so it had the drivers already and it's the same computer I went through the download mode before with so I have the drivers. I tried to reinstall them but still nothing.
I fear I may need to buy out my contract :crying:

Tical84 said:
Same problem here, I actually didn't see this in my search and made a new thread about it (feel free to delete). My computer had KIES on it so it had the drivers already and it's the same computer I went through the download mode before with so I have the drivers. I tried to reinstall them but still nothing.
I fear I may need to buy out my contract :crying:
Click to expand...
Click to collapse
I am sure that I am right with this. "If you root, do not use KIES" so you have to uninstall KIES and download separate USB driver.
Then it should see your phone when connect with ODIN
Hope you got your phone back alive soon

USB Connection
Italia99 said:
Yes i'm 1000% sure!
I can acess the Download Mode, but Odin/Heimdall does not recognize the USB connection...
Click to expand...
Click to collapse
Did you checked usb drivers, if not try to connect another samsung android device to your pc first. if another phone connected properly then problem in your phone only.
i suggest check this thread, if you think you completely lost your device - http://forum.xda-developers.com/showthread.php?t=819551

coepeq said:
I am sure that I am right with this. "If you root, do not use KIES" so you have to uninstall KIES and download separate USB driver.
Then it should see your phone when connect with ODIN
Hope you got your phone back alive soon
Click to expand...
Click to collapse
Sorry, I should have been more specific. When I reinstalled the drivers I had actually uninstalled KIES and installed just the drivers.
I do have an update though but still can't get it to boot completely. Late last night I decided to try to get download mode to work one last time before passing out and pressing Vol-, Home and Power actually brought me to the recovery screen for the first time in my phone's life! "F YA!" was the only thing I could think at the time so I first went through and formatted/wiped every option I could find then installed the CM9 that I knew worked and now I get to the alien with the matrix-esque background and it stops there. I plugged it in and left it on that screen all night and that guy was still staring at me this morning. I tried download mode again but my computer still doesn't recognize it.

[Q] Is there anyway to flash stock rom via cwm

Im on ics rom right now and im stuck on it. My computer wont recognize my phone, i tried installing drivers and many other things but it just wont work... Can someone tell me what to do??? (i tried connecting to other computers but it doesnt work) If not can someone suggest custom rom that doesnt drain 1% of battery in 2 minutes.

xXcRazycRackeRXx said:
Im on ics rom right now and im stuck on it. My computer wont recognize my phone, i tried installing drivers and many other things but it just wont work... Can someone tell me what to do??? (i tried connecting to other computers but it doesnt work) If not can someone suggest custom rom that doesnt drain 1% of battery in 2 minutes.
Click to expand...
Click to collapse
Did you try a other computer? Sometimes the computer fails to identify you device, happend to me 1 time.
Or try Blazr rom, fast stable and very long battery life!
Just put the zip file on your sdcard and copy it to your phone (since your computer doesnt let you connect via usb)
Then go into recovery mode en update via zip file.
See this link for the rom: http://forum.xda-developers.com/showthread.php?t=1628639
Everything you need is posted there.
Greetings

CybertekDj said:
Did you try a other computer? Sometimes the computer fails to identify you device, happend to me 1 time.
Or try Blazr rom, fast stable and very long battery life!
Just put the zip file on your sdcard and copy it to your phone (since your computer doesnt let you connect via usb)
Then go into recovery mode en update via zip file.
See this link for the rom: http://forum.xda-developers.com/showthread.php?t=1628639
Everything you need is posted there.
Greetings
Click to expand...
Click to collapse
I tried it on friends computer.
And i need i9000 roms.

xXcRazycRackeRXx said:
I tried it on friends computer.
And i need i9000 roms.
Click to expand...
Click to collapse
Odin or Heimdall is the only way, but try flashing another ics Rom to see if it fixes the phone not being recognised

slaphead20 said:
Odin or Heimdall is the only way, but try flashing another ics Rom to see if it fixes the phone not being recognised
Click to expand...
Click to collapse
I tried almost every ics rom but it didnt work. I guess i will have to buy new usb cable and check if there is something wrong with the phone.

I had the same problem, I uninstalled the usb drivers and installed them again and it seemed too work fine
Sent from my potato using xda app-developers app

xXcRazycRackeRXx said:
I tried almost every ics rom but it didnt work. I guess i will have to buy new usb cable and check if there is something wrong with the phone.
Click to expand...
Click to collapse
yep, the cable is likely the common cause and problem but not all cables are compatible, best to get original or bring phone and test data mode before buying as charging mode works on all
on the other hand, just examine your usb slot too..a slight misalignment can also cause this problem

xsenman said:
yep, the cable is likely the common cause and problem but not all cables are compatible, best to get original or bring phone and test data mode before buying as charging mode works on all
on the other hand, just examine your usb slot too..a slight misalignment can also cause this problem
Click to expand...
Click to collapse
Will Sgs 2 cable work?

xXcRazycRackeRXx said:
Will Sgs 2 cable work?
Click to expand...
Click to collapse
give it a try, it should

[i9000b] BSOD - Phone ! Computer Screen

I had Android 4.0.3 (IceCream Sandwich) on my Galaxy S GT-I9000B (I did install it through Odin, nothing went wrong), but is was laggish (too much for it to handle, I think) and after a few months, I decided to roll it back to 2.3.3 (Gingerbread).
I started the process to install the firmware through Odin3 v1.85 - the file I download (from sammobile.com/firmware, had only one file that I used on the PDA space.
Odin recognized my phone and I started to install it, but after a while my phone was stuck on the downloading screen (2 hours of installation, I tought that something went wrong).
I then turned my phone off to try and install again, but when I turned it on, there were a Phone - exclamation mark - Computer Symbol.
I can get it to dowlonad mode (Volume Down+Home+Power), but when I plug it to the pc, it says "unknown device" and it can't find drivers for it.
I think I have the latest drivers from Samsung (I had from Kies and I re-downloaded a file somewhere from this forum named SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_6_0.exe).
It appears that since windows can't install the drivers, Odin doesn't recognize the device - it was recognizing it before, when I was installing the firmware.
Now I'm stuck - I tried anything I saw in this forum and in other places - I did even pray for a miracle, but it didn't work
I know that there must be a way, but I don't know how.
Before I forget, I'm using Windows 7 Ultimate x64.

If you can get it in download mode everything should be fine, I've had a problem like this, my pc couldn't see the phone in download no matter what. Try to use another USB port, better another PC. Also I've heard that x64 doesn't get along well with Odin. If possible you can try Linux and Heimdall, after all Android is Linux too.

KainFromNod said:
I know that there must be a way, but I don't know how. Before I forget, I'm using Windows 7 Ultimate x64.
Click to expand...
Click to collapse
Ok, k4Z3666, has given you a starting point...the phone is still in download mode but without a booting ROM, so its OK, the problem is your PC, USB cable or USB port. If you want to be quick about it, just try on a lap top..if not a simple Reboot of PC ( after removing power cord) and Phone (after a battery Pull), and a switch to a different USB port at the back of PC can solve this for some...for other solutions try these http://forum.xda-developers.com/showpost.php?p=27205737&postcount=4571 anything else you may need can be found on My Android collections., link below

k4Z3666 said:
If you can get it in download mode everything should be fine, I've had a problem like this, my pc couldn't see the phone in download no matter what. Try to use another USB port, better another PC. Also I've heard that x64 doesn't get along well with Odin. If possible you can try Linux and Heimdall, after all Android is Linux too.
Click to expand...
Click to collapse
I tried other USB Ports and also rebooting. It was working just fine - it seems like a driver problem to me.
My notebook is dead, but I'll try using someone else computer.
Does Odin runs in Windows XP? I might try it in my virtual box - I doubt that it will work, but it is the best thing I have to do untill tomorrow.

I got it working in my mother's notebook - should I try something different? I only have the PDA, should I try a PIT?
I don't know what those do, but I read somewhere that PIT is used to recover bricked phones.
EDIT: I installed only the PDA, it worked fine on the 2nd time (first time, it got stuck but I could make it work changing the usb port and cable).
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?

KainFromNod said:
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?
Click to expand...
Click to collapse
what ROM did you use? Did you do any wipes?
Opps..you got an i900B, so make sure you are only using I9000B ROMS as i9000 is not compatible with your phone
Follow guidelines from here
http://forum.xda-developers.com/showthread.php?t=919219
http://forum.xda-developers.com/showpost.php?p=22941192&postcount=300

KainFromNod said:
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?
Click to expand...
Click to collapse
Assuming that you're on the right rom for your phone can you enter recovery mode? Try reinserting battery, and enter recovery with [vol+, menu button, power on]

KainFromNod said:
I got it working in my mother's notebook - should I try something different? I only have the PDA, should I try a PIT?
I don't know what those do, but I read somewhere that PIT is used to recover bricked phones.
EDIT: I installed only the PDA, it worked fine on the 2nd time (first time, it got stuck but I could make it work changing the usb port and cable).
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?
Click to expand...
Click to collapse
Yep if u want to back to stock u need pit file because ICS use different system file
Why u don't like ICS ? Its way better and faster than sammy ROM even its more stable , I think u should try it again with devil kernel with oc to 1.2 it will fly u can add some live oc which will give more fluidity
Sent from another galaxy powered by CM10 & Syiah

Ok, I'm posting it here just to leave a reply and reference for future generations, as my problem was solved.
xsenman said:
what ROM did you use? Did you do any wipes?
Opps..you got an i900B, so make sure you are only using I9000B ROMS as i9000 is not compatible with your phone
I used a firmware from my country (available here: sammobile.com/firmware/?page=3&model=GT-I9000B&pcode=ZTO&os=1&type=1#firmware) and I wiped the cache (I'm not sure what this means, but I believe it is the 2 options on volume up+menu+power)
Follow guidelines from here
http://forum.xda-developers.com/showthread.php?t=919219
http://forum.xda-developers.com/showpost.php?p=22941192&postcount=300
Click to expand...
Click to collapse
k4Z3666 said:
Assuming that you're on the right rom for your phone can you enter recovery mode? Try reinserting battery, and enter recovery with [vol+, menu button, power on]
Click to expand...
Click to collapse
I was entering recovery mode, but it was giving me some error when I tried to wipe the 2 things that I forgot the name =/
yahyoh said:
Yep if u want to back to stock u need pit file because ICS use different system file
Why u don't like ICS ? Its way better and faster than sammy ROM even its more stable , I think u should try it again with devil kernel with oc to 1.2 it will fly u can add some live oc which will give more fluidity
Sent from another galaxy powered by CM10 & Syiah
Click to expand...
Click to collapse
ICS wasn't faster here - it was laggish and always crashed some common apps (gallery, music player). I believe that the firmware wasn't completely "done" as it was being adapted from another version (my phone is brazilian) and some functionalities that it has (i.e. digital TV) wasn't available.
What I done to correct the boot was simple (I found a tutorial in a brazilian site, so it had all the roms that I needed).
1) Used a PIT and a stock rom to get it back to factory version;
2) Upgraded to Froyo (original) - That was kind of a mistake, the tutorial said to do it because then KIES would update it automatically to Gingerbread. The phone was fully functional, but KIES said that it couldn't update it (it recognized the phone and everything).
The tutorial stoped there, but since I had the ROM, I used Odin to install Gingerbread (the one that was looping) and it was done.
Now I need to remember how to root it because there are some dumb apps who can't get away (i.e. Orkut app, some demo games).
Thank you all for the help!

KainFromNod said:
I was entering recovery mode, but it was giving me some error when I tried to wipe the 2 things that I forgot the name =/
Click to expand...
Click to collapse
From recovery you can always try to flash another kernel, that would probably resolve things too. Anyways the problem's solved, glad to help

[Q] Help Needed in Unbricking Samsung Galaxy Pop (GT S5570)

Please help me out on this....
(Sorry if I posted in wrong section)
I successfully upgraded my Pop to gingerbread 2.3.6 and rooted it. It was working fine for some days after which It got messed up
when I updated the titanium backup app from the market. The app asked for some su permissions and suddenly the screen went blank.
After that I realized that its a hard bricked. The screen is blank whatever I do. I searched for many tutorials to unbrick it but no fruitful results yet.
I tried a lot to enter download mode and after several attempts luckily the three button combo worked and it got shown in ODIN on some port connected.
When I started the process of firmware upgrade it gets stuck in "Connection Setup Phase".
Does USB Jig method is worth trying in this situation ??
Pease tell me the solution of it. I am attaching the screenshot of the ODIN. Please Please Please help.
Thanks a lot in advance...

what is on your mobile screen download mode or something like phone--!--computer picture
ok whatever try this
close Odin, turn off mobile, start Odin and put files turn on mobile in download mode connect the cable and start flashing
PS : phone--!--conputer shows on the screen when upgrade get fail, not to worry it is just like another version of Odin
until you can light up the mobile its not a hard brick
I will suggest you to use firmware which are available without bootloader as you were previously on gb, just to remove the risk of hard brick

nothing on screen
yagnesh55 said:
Please help me out on this....
(Sorry if I posted in wrong section)
I successfully upgraded my Pop to gingerbread 2.3.6 and rooted it. It was working fine for some days after which It got messed up
when I updated the titanium backup app from the market. The app asked for some su permissions and suddenly the screen went blank.
After that I realized that its a hard bricked. The screen is blank whatever I do. I searched for many tutorials to unbrick it but no fruitful results yet.
I tried a lot to enter download mode and after several attempts luckily the three button combo worked and it got shown in ODIN on some port connected.
When I started the process of firmware upgrade it gets stuck in "Connection Setup Phase".
Does USB Jig method is worth trying in this situation ??
Pease tell me the solution of it. I am attaching the screenshot of the ODIN. Please Please Please help.
Thanks a lot in advance...
Click to expand...
Click to collapse
dheeraj (dhlalit11) said:
what is on your mobile screen download mode or something like phone--!--computer picture
ok whatever try this
close Odin, turn off mobile, start Odin and put files turn on mobile in download mode connect the cable and start flashing
PS : phone--!--conputer shows on the screen when upgrade get fail, not to worry it is just like another version of Odin
until you can light up the mobile its not a hard brick
I will suggest you to use firmware which are available without bootloader as you were previously on gb, just to remove the risk of hard brick
Click to expand...
Click to collapse
There is nothing shown on my screen...
no computer like symbol....
nothing whatever i do...
It just goes sometimes in download mode when the 3 button combos is pressed (very rarely), gets detected by ODIN but stucks on connection error...

yagnesh55 said:
There is nothing shown on my screen...
no computer like symbol....
nothing whatever i do...
It just goes sometimes in download mode when the 3 button combos is pressed (very rarely), gets detected by ODIN but stucks on connection error...
Click to expand...
Click to collapse
First of all delet all drivers on pc and install them new, just to be on the save side! Then get firmware for your country i suggest you to use 4file pack no the 1file ones! Then get odin v4.38 put your device in download mode and conect to pc put all 4files in the right place in odin and start flashing!! It should not take longer then 6min!! Let odin finish when you see blue pass disconect and be lucky!!
Sent from my GT-S5570 using xda premium

It Doesnt Help
galaxy mini said:
First of all delet all drivers on pc and install them new, just to be on the save side! Then get firmware for your country i suggest you to use 4file pack no the 1file ones! Then get odin v4.38 put your device in download mode and conect to pc put all 4files in the right place in odin and start flashing!! It should not take longer then 6min!! Let odin finish when you see blue pass disconect and be lucky!!
Sent from my GT-S5570 using xda premium
Click to expand...
Click to collapse
I tried this thing many times but still ODIN stucks on connection setup...
Also tried on different machine...
Please help....

yagnesh55 said:
I tried this thing many times but still ODIN stucks on connection setup...
Also tried on different machine...
Please help....
Click to expand...
Click to collapse
Have you tried using a different port? Or a different cable? Also, try unchecking the reset time option on ODIN.

tietganFTW said:
Have you tried using a different port? Or a different cable? Also, try unchecking the reset time option on ODIN.
Click to expand...
Click to collapse
there are two data cables of the same shape but their holes (which goes in mobile port) are of different size try the data cable whose hole is much big
I will try to post a pic
in short use the original Samsung one

1st try flashing cwm via odin n then wipe data wipe sd partition n then go to stock rom via odin

Flash Stock Rom for ur device using odin..... Please do not do any thing you area not aware of..
Files the steps and will make ur device ok
Click THANKS button if I helped, or u liked my post.
Will be honored.

dheeraj (dhlalit11) said:
there are two data cables of the same shape but their holes (which goes in mobile port) are of different size try the data cable whose hole is much big
I will try to post a pic
in short use the original Samsung one
Click to expand...
Click to collapse
ya I got ur point regarding the port size...
I m using the port of samsung original having big hole....
sanjay.ghanchi said:
1st try flashing cwm via odin n then wipe data wipe sd partition n then go to stock rom via odin
Click to expand...
Click to collapse
The screen is completely blank whatever I do so I cant do these steps ....
debanikonline said:
Flash Stock Rom for ur device using odin..... Please do not do any thing you area not aware of..
Files the steps and will make ur device ok
Click THANKS button if I helped, or u liked my post.
Will be honored.
Click to expand...
Click to collapse
Ya m flashing stock ROM using ODIN but it gets stuck on connection setup stage forever (see attached file)...
Please help...
Anyone having idea if USB jig work in this case...

yagnesh55 said:
Anyone having idea if USB jig work in this case...
Click to expand...
Click to collapse
USB jig only boots mobile in download mode
but you are saying you can sometimes boot in download mode so no use of USB jig is required
you should take it to samsung

Weird. I dont know how you could brick your phone with titanium backup app.
Your battery could be dead. Charge your phone for 2 hours.
Then try using Odin using a different USB Port.

chemicalrage said:
Weird. I dont know how you could brick your phone with titanium backup app.
Your battery could be dead. Charge your phone for 2 hours.
Then try using Odin using a different USB Port.
Click to expand...
Click to collapse
Nop I charged my battery full with another battery charger before using ODIN but still the problem persist.
I think I have to take it to Samsung service center but my warranty is over so I think they will take a huge amount
to fix it.
Anyone still having some idea on this...
Pease help...

yagnesh55 said:
Nop I charged my battery full with another battery charger before using ODIN but still the problem persist.
I think I have to take it to Samsung service center but my warranty is over so I think they will take a huge amount
to fix it.
Anyone still having some idea on this...
Pease help...
Click to expand...
Click to collapse
Dude We are On the Same Boat I Tryed Searching With All My resources But Now There Is Only 1 Option Left for Me to Visit to a Service Center

Service Centre Sucks
amxthan0 said:
Dude We are On the Same Boat I Tryed Searching With All My resources But Now There Is Only 1 Option Left for Me to Visit to a Service Center
Click to expand...
Click to collapse
I gave my phone to service centre (warranty is over ) before few days and they told than some connector in the circuit is damaaged and need to be replaced with new
one and its cost is 4278 INR . Can u believe that ??? 4278 bucks. Its better to buy a new phone.

yagnesh55 said:
I gave my phone to service centre (warranty is over ) before few days and they told than some connector in the circuit is damaaged and need to be replaced with new
one and its cost is 4278 INR . Can u believe that ??? 4278 bucks. Its better to buy a new phone.
Click to expand...
Click to collapse
You should have tried another stock firmware or another USB port when your phone luckily entered download mode. Same problem happene with me & get solved by flashing another stock firmware.
Sent Via XDA™ Premium

Galaxy_Rohit said:
You should have tried another stock firmware or another USB port when your phone luckily entered download mode. Same problem happene with me & get solved by flashing another stock firmware.
Sent Via XDA™ Premium
Click to expand...
Click to collapse
Tried every damn thing but ODIN gets stuck on connection setup step....