Related
This thread is primarily intended for n00bs.
I would like to say thanks to xda forum members: Noejn, Zecanilis, drellisdee, The_ERROR etc. Also thanks is due to Godlike! at tech-mania.com for his tutorials. Thanks is due especially to The_ERROR for proofreading the post and to other users for their suggestions written in the thread.[/SIZE]
---------------------------------------------------------------------------------------------
NEW - 3 May 2011 - Simplified Guide to Root & install version 1.2 of Custom Thunderg Recovery by AmonRa/modified by Drellisdee on LG P500
ALWAYS MAKE A BACKUP BEFORE CUSTOMISING YOUR PHONE.
[CUSTOMISING A PHONE USUALLY INVOLVES: ROOTING >>>> INSTALLING CUSTOM RECOVERY >>>> INSTALLING CUSTOM ROM]
The instructions written below have been tested by me using an Indian unbranded GSM model of LG P500 which came with stock Android 2.2.1 (V10C). The procedure to be followed for any LG P500 phone is the same.
This post is split into 4 major sections -
1. INSTRUCTIONS FOR ROOTING
2. INSTALLING ANDROID SDK ON A WINDOWS PC (This step is needed to install Custom Recovery on phone using adb from PC. Can be omitted if Recovery is installed from phone using Terminal Emulator)
3. INSTALLING A CUSTOM RECOVERY
4. INSTALLING CUSTOM ROMs
MUST READ: If you haven't read this thread already, please do read it - Dictionary for n00b - What is.../What does ...mean?
---------------------------------------------------------------------------------------------
1. INSTRUCTIONS FOR ROOTING
To know your present firmware version - Go to Settings/About Phone
Only phones which come with stock android 2.2 could be rooted till recently.
UPDATE - 24 April 2011 : A tool called 'GingerBreak APK' is able to root phones running stock android 2.2, 2.2.1 & 2.2.2. Read about it HERE. This tool enables rooting without the need for downgrading the firmware to 2.2. If 'GingerBreak APK' doesn't work out for you, continue reading to understand the procedure to root your phone after downgrading your firmware. Note: 'GingerBreak APK' permanently roots your phone. Also,GingerBreak might not install BusyBox and SuperUser apps properly on your phone. These apps are required by many rooted apps for their proper functioning. So, use Root Checker from android market to verify the proper installation of these 2 apps.
If your phone runs stock android 2.2, enable 'USB Debugging' on Phone (Settings/Applications/Development). Install z4root (copy the apk file to the sd card and open the file after browsing to the location using the phone's file manager), run it and root the phone. Find it HERE.
Choose the permanent root option as it is still possible to force unroot if needed.
Restart the phone and launch z4root to check the root status. A successful rooting should show 'Unroot' option when z4root app is opened.
{Note: z4root automatically installs Busybox and Superuser application(which appears as an icon in your app drawer) on the phone.}
If rooting fails with z4root, there is another application called SuperOneClick which can root your phone. Read about it HERE
For phones that came with stock 2.2.1 or 2.2.2 installed, rooting first involves downgrading the firmware to 2.2.
Downgrading the firmware can be done with KDZ-FW-UPD.exe (procedure outlined below)
(KDZ-FW-UPD.exe has been claimed to work best with windows xp 32bit.)
FIRST: DOWNLOAD THE Android 2.2 FIRMWARE FOR YOUR DEVICE. For this, go to: [ROMS] Original LG Firmware list and read about the procedure to download the original firmware.
{Tips: Use Ctrl+F in browser to search for Country name, Remember to change the alphabet in 2 places in the final link to download the firmware, Do not bother about the 'CDMA' tag attached to country code. It works for the GSM model phones too. If the link to find out the country codes doesn't work, use the 2nd method mentioned in the post to find out the country code using your phone's IMEI or ESN number }
Download the required Firmware onto your PC.
Links to Original firmware versions for Indian P500 are mentioned in THIS POST
Procedure to install original firmware using KDZ-FW-UPD.exe ( KDZ FIRMWARE UPDATER ) This procedure can also be used to restore the stock firmware and recovery onto your phone in case you want to give your phone to the service centre during warranty period as the phone will appear similar to as you bought it from the store.
[Note: This procedure was used to install V10B_00.kdz(android2.2) over V10C_00.kdz(android2.2.1) on an unbranded Indian GSM model of LG P500 using a Windows 7 Ultimate 64bit updated to date PC.]
1. Install LG PC Suite IV from SD card which came with phone by connecting the phone to PC through USB cable. This is done to install the drivers for the phone on the PC (the procedure is as follows)
- Enable the 'USB Mass Storage Only' mode in the phone's Settings/SDcard & Phone Storage menu.
- Connect phone to PC with the USB Cable.
- Press the 'Turn on USB Storage' button which appears on phone.
- Browse to the folder containing the 'LG PC Suite IV' on the phone's SD card using Windows Explorer and run the LG Installer file. PC Suite will now install on your system along with the required drivers for your phone.
- Cancel setting up PC Suite or continue setting up PC Suite if you want to Sync or backup the phone data.
- After closing PC Suite, Safely remove the USB device from your system.
- Press the 'Turn off USB Storage' button on phone screen.
- Detach the USB Cable.
- Disable the 'USB Mass Storage Only' mode in the phone's Settings/SDcard &Phone Storage menu.
Alternatively, I also tried installing the latest drivers via LG Mobile Support Tool from LG's website (available HERE) but KDZ-FW-UPD.exe (mentioned below) crashes when run. This could be happening only to me, so please try for yourself before writing off this method.
2. For my comfort more than anything else, I switched off the screensaver and other power saving features on the PC and also set the screen timeout delay on the phone to 30 minutes.(Settings/Display/Screen Timeout)
3. Charge the phone to the maximum.
4. Enable USB Debugging on Phone (Settings/Applications/Development).
5. Detach all other peripherals from your PC. Exit all running applications on your PC especially other PC suites if any. Also exit running programs from the notification bar on the desktop. (Also uninstall Nokia or other phone drivers & microsoft visual ++ runtime environments - not an essential step.)
6. Disable 'LGE Virtual Modem' in PC's Device Manager. (In your Windows operating system, go to Control Panel > System > Hardware > Device Manager > Modems > Right click on LGE Virtual Modem and click Disable.)
7. Unmount the SD card from the phone (Settings/SDcard & Phone Storage).
8. Open phone back and remove the SD Card.
9. Download KDZ_FW_UPD_EN.7z onto your PC and extract it to a folder. Available HERE.Direct Download Link. (MD5 of 7zip file - 813A28BE9182AB604A1D43E745CE7AD7)
10. Run the msxml.msi file and complete the installation.
11. Connect the phone to PC with USB Cable.( If you are using a desktop PC, make sure you use USB ports that are in the back of your PC, avoid the front ports.)
12. Run KDZ_FW_UPD.exe from the extracted folder.
13. Chose TYPE as 3GQCT & Phone Mode as DIAG.
14. In the 'KDZ file' space, browse for the firmware you want to install. (In this case V10B_00.kdz)
15. Press the 'Launch software update' button.
16. The firmware flashing process is now underway.
If all goes well, in 5-10 minutes the phone will be flashed with the new firmware.
I shall describe in detail what happened with my phone - 10-15 seconds after launching software update on PC, my phone screen turned blank and in a couple of seconds the phone entered the 'Emergency Mode'. During this mode the screen was yellow with Emergency Mode written along the middle of the screen. The phone stayed in the same way till the Software update procedure finished on the pc and the phone turned blank. I waited a while for it to reboot but after a minute or so, I manually switched on the phone. The phone came alive and following the LG boot animation, the android logo screen came up. The phone spent about 2 whole minutes in that state before booting up fully and entering the home screen. Update: Wait till phone reboots by itself or wait for a while before manually switching it on.
17. After booting up fully, detach the phone from the pc.
(If the phone gets stuck in the android boot logo screen during first boot, doing a hard reset by pressing and holding the VolDown+Home+Power buttons may resolve the problem.)
Go to 'About Phone' in Settings and confirm the change from 2.2.1 or 2.2.2 to 2.2.
Root the phone using z4root as mentioned before.
If rooting fails with z4root, there is another application called SuperOneClick which can root your phone. Read about it HERE
IN CASE OF PROBLEMS DURING DOWNGRADING FIRMWARE, read the following thread completely. Various types of errors and various measures to correct them including some innovative ones like shaking the phone etc. are mentioned here - [HOWTO] Phone not responding at all - last chance to repair. It is advisable to read this thread completely before attempting to downgrade the firmware using KDZ_FW_UPD.exe to become aware of all the possible problems you might encounter and their possible solutions.
PS: Here is the link to the phone drivers that came with my SD card. One user reported a problem wherein kdz updater would recognise the phone but the update process would fail during kdz unpacking. the problem was resolved by using the drivers i sent him. So, if anyone has the same issue, it might be worthwhile to try out the following drivers. I wouldn't advise everyone to follow this method, but those of you who are feeling lucky might try it out. Download Link
---------------------------------------------------------------------------------------------
2. INSTALLING ANDROID SDK ON YOUR WINDOWS PC
This step is required to install Custom Recovery on your phone using adb from your PC. Using a Custom Recovery, you can make a backup of your current ROM, restore backups, create partitions on your SD card, wipe your phone and the SD card and then also go on to install Custom ROMs using the Flash from Zip option.
Installing a Custom Recovery can also be done in other ways. Using Android SDK from your PC is just one method.
(Custom Recovery can alternatively be installed on your rooted phone using the commands given in the next section using a Terminal Emulator. This method removes the need for installing Android SDK on your PC and connecting your phone to PC. Download Terminal Emulator from Android Market. Install on phone. Run it and give it root permissions when prompted by the 'Superuser' application. As mentioned in the next section, copy the 2 files (flash_image & the custom recovery image file) needed to install Custom Recovery onto the root directory of SD card. Reboot phone. Open terminal emulator and type 'su' without the quotes and press Enter. This will take you to the root shell (#) from the default user shell($). Carefully type in the 7 commands mentioned in the next section one after the other. After typing in the last command (reboot recovery) and pressing enter, WAIT. The phone will reboot. Custom Recovery will have been succesfully installed on your device.
Hint: Copy the installation commands as a text file to phone & copy and paste the commands one by one into terminal emulator using a text editor. Please make the necessary changes to the installation commands depending on the recovery version used)
To install Android SDK on PC, there are a few requirements/downloads which have to be completed first:
JDK (Java Development Kit) - Download Here
JRE (Java Runtime Environment) - Download Here
Android SDK installer - Download here
So after all the downloads are completed, you are good to go. Run PC as Administrator.
First of all install the JDK, then the JRE and then the SDK Installer.
{If when android sdk installer is run, you get an error that JDK or JRE is not detected even after their installation, wait for a while, shut down the computer and restart and run the SDK installer once again.}
Make sure that while installing the android sdk, the installation directory should be the root of a partition i.e. it should be in the following form: C:\android-sdk, where you should replace the letter C with the letter you have assigned to the partition that you want to install it in.
Now that the Android-SDK is installed, go to the installation directory and start the SDK Manager. You need to add the components of the Android SDK to your installation. Before that I would like to inform you that you can save time if you download only what is necessary. If you are on Android 2.1 then you should download the 2.1 sdk, for 2.2 the 2.2 sdk and so on. You do not need to have all the versions for this thing to work. Just your version would do. So to start adding components, I recommend that you read THIS
After installing the desired components, you need to do perform some simple steps in order to use the adb terminal just like the cmd terminal for Windows.
For that purpose, here are the steps to be followed:
Right click My Computer, select Properties, and click Advanced System Settings. (Windows XP users - Right click My computer and just click Properties and select the Advanced Tab)
Click on Environment Variables, in the System Variables box, scroll down to the variable name 'Path' and double click to edit it
It would read something like " %SystemRoot%\system32;%SystemRoot%;%SystemRoot%\System32\Wbem;%SYSTEMROOT%\System32\WindowsPowerShell\v1.0\;C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static".
Here you need to add a semicolon ( ; ) and add the path of the tools folder in android-sdk.
It should finally be like this " %SystemRoot%\system32;%SystemRoot%;%SystemRoot%\System32\Wbem;%SYSTEMROOT%\System32\WindowsPowerShell\v1.0\;C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static;C:\android-sdk\platform-tools {or the location where adb.exe resides on your system}
Click OK wherever asked and then restart your computer.
Now open a command prompt window and type adb and hit enter. If a terminal window is displayed, you have done it all right.
If it gives some error message, read the article carefully and see what you have messed up with.
---------------------------------------------------------------------------------------------
Tip:
Using adb - How to install apps from PC without having to copy them first to the SD card?
If you want to install apps in one click, all you need to do is download the .apk file of your application to your PC and set the open with option to this batch file which you can download HERE
Save the batch file on the desktop of your PC before setting the option to 'Open With'.
---------------------------------------------------------------------------------------------
3. INSTALLING A CUSTOM RECOVERY
(Procedure of installing Custom Recovery using a terminal emulator from your phone instead of installing android SDK on your PC and connecting your phone to PC is mentioned in the last section.)
UPDATE - 3 May 2011 : Very simple way of installing Custom Thunderg Recovery by AmonRa/modified by Drellisdee version 1.2. Originally posted by ungaze in this post.
1. Download Android Terminal Emulator from Android Market. Install it on your rooted phone.
2. Download the file "amon_ra_recovery_installer.zip" from here or here. Check the MD5 hash value of the downloaded 'zip' file using tools like HashTab etc. before proceeding further. Correct MD5 value : 86db8a52b01f049cadb8f097a4c5bd9e
3. Extract the contents of the 'zip' file to the root of the sd card (ie. not inside any folder) using tools like 7-Zip or WinRAR or any other similar tool.
4. Open the terminal emulator app on your phone and type in the command 'su' without the qoutes. This will prompt a popup on your phone from the SuperUser app asking you whether you want to give root permissions to the terminal emulator app. Click 'Allow' and proceed. You will notice that the shell prompt has changed from the previous user shell '$' to root shell '#' in the emulator app.
5. While in the root shell '#', type in the following command and press Enter. Wait and the phone will reboot into the Custom Recovery.
Code:
sh /sdcard/rf.sh
Once you are up and running with a rooted phone, you will need to download the 2 files needed to install the Custom Recovery. They are:
Download No:1: flash_image - (This file is the same one needed to install any of the 3 versions of Custom Thunderg Recovery by Drellisdee given below)
Download Link (MD5 of zip file - 13FED5DF927214D744A256DAB4C3DC06)
Mirror Link (MD5 of zip file - 13FED5DF927214D744A256DAB4C3DC06)
Mirror Link - requires registration at androidforums.com. (MD5 of zip file - 13FED5DF927214D744A256DAB4C3DC06)
Download No:2: Custom Recovery image file - Choose & download any version among the 3 available after reading what is written below.
Custom Thunderg Recovery by Drellisdee has versions 1.1, 1.2 and 1.2.1 at the time of writing this. I personally prefer version 1.2 as it supports backup & restoration of ext4 Partition on SD Card. Version 1.2.1 is a little experimental in nature & it may not fit all devices as it has a size near 5 MB.
Link to xda-forum thread for Custom Recovery P500/Thunderg - HERE.
The different versions of the Custom Recovery image files are available at the following pages
Custom Recovery P500/Thunderg v1.1
Direct Download link - (MD5 of zip file - eb4ea2ffb26f387a891bb4d7261a0e5f)
Mirror Link - (MD5 of zip file - eb4ea2ffb26f387a891bb4d7261a0e5f)
Custom Recovery P500/Thunderg v1.2
Direct Download link - (MD5 of zip file - 217FC9115899A41195CF124CAF07B880)
Custom Recovery P500/Thunderg v1.2.1
Direct Download link - (MD5 of zip file - 388aac16b1184ab15b5500b2b32d914c)
Please check the MD5 hash values of downloaded files to ensure that files are not corrupted using tools like HashTab etc.
Now to install Custom Recovery, Copy the two files [ the chosen recovery image file (*.img) & the flash_image file (flash_image) ] and paste in the root of your SD card (root means the directory L:\ where L is the letter for your Phone's USB Storage. In short, don't create a folder and paste the files inside it on your SD card).
{Note that the recovery image file should have an .img extension and flash_image file should have no extension when placed on the SD card}
Reboot the phone. Connect phone to PC.
The next step requires Android SDK to be installed on your PC.If you have installed the Android SDK, follow these steps:
Go to Start Menu & Run and type cmd (run as Administrator)
In the cmd window, type adb. If you have installed it correctly, you will see a lot of text on the screen. If you get an error message then you have probably not installed the Android SDK properly.
Type adb shell and hit enter
Type su and hit enter
See your phone at this time and touch the 'Allow' option which SuperUser shows you
Now the terminal window will have a # sign appended to it instead of the previous $ sign. See this screenshot for a better understanding
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Now one by one, copy the following lines, in the serial order and paste it into the terminal window and press enter following each line(right click on window and paste, CTRL + V won't work)
mount -o remount,rw -t yaffs2 /dev/block/mtdblock1 /system
cat /sdcard/flash_image > /system/bin/flash_image
chmod 755 /system/bin/flash_image
mv /system/etc/install-recovery.sh /system/etc/install-recovery.sh.bak (if it gives error message here, simply proceed to the next step)
mount -o remount,ro -t yaffs2 /dev/block/mtdblock1 /system
flash_image recovery /sdcard/LGp500-recovery-v12.img (If the recovery version chosen is different from v1.2, type the appropriate file name of the recovery image here instead.)
reboot recovery
Click to expand...
Click to collapse
Wait. The phone will reboot now.
Note:{If you get this error after step 4
mv /system/etc/install-recovery.sh /system/etc/install-recovery.sh.bak
failed on '/system/etc/install-recovery.sh' - No such file or directory
Simply move on to the next step.
If you get any errors other that those mentioned here, please do not proceed with the last command of 'reboot recovery'. If you do so, recovery may not be correctly installed and you will lose all data on the phone as the phone will be reset to factory defaults. Please go back to the instructions and see what you have done wrong.
NOTE: If on booting into the recovery you get the following message at the bottom of the screen -
E: 'Bad Boot Message'
Don't panic, it's perfectly normal and you can proceed with what you want to do from the recovery.}
Detach the phone from the PC.
To access the Custom Recovery, turn off the phone and then press & hold Home+Vol Down+Power buttons to boot into the Custom Recovery.
---------------------------------------------------------------------------------------------
Once you have booted into the recovery, the touch screen won't work. The actions assigned to the different buttons are given here. Use them to navigate through the different options in Custom Recovery.
Up & down: vol-up and vol-down key
Select: Menu key (left most)
Back: Back (3rd from left)
---------------------------------------------------------------------------------------------
What does Custom Recovery look like & What does it do?
Note: In Custom Recovery versions 1.2 and above, zips can be extracted from inside folders. So, save the zips in a folder named AAA and flash the zip after browsing inside the folder through recovery. The folder name should be named 'AAA' so that it appears among the first on the recovery screen, since scrolling is not an option in recovery.
Note: There is also an unofficial port of ClockworkMod Recovery availble. I do not recommend this recovery for newbies as it isn't compatible with all Custom ROM's out there.
---------------------------------------------------------------------------------------------
4. INSTALLING CUSTOM ROMs
BEFORE FLASHING ANY ROM, DO A NANDROID BACKUP FROM CUSTOM RECOVERY
Since all the ROMs have their own kinds of partitions to be created and other requirements, you can check them at the ROM specific pages.
General procedure to follow for installing a Custom ROM
Boot into Custom Recovery
Wipe your cache, dalvik cache, SD card
Make partitions according to the ROM requirement
Wipe cache again.
Connect Phone to PC
Toggle USB MS and paste the ROM zip file to a folder called AAA in the root of the SD card
Disable USB MS.
Detach phone from PC.
Select 'Flash from zip' option in Custom Recovery menu
Select the ROM file
Flash the ROM file
After flashing is finished, Reboot the phone.
Note: It will take some time to flash and reboot into your new Custom ROM. The phone may stay with the boot logo displayed for a number of minutes. Do not switch off phone during this period.
---------------------------------------------------------------------------------------------
In case of problems with phone, read: [HOWTO] Phone not responding at all - last chance to repair
Also read: [READ FIRST] [REF] Repository of howto's, roms, kernel, etc.
If you feel benefited by this thread, I humbly request you to rate this thread and vote it to the front page. The option to rate and vote is present in the title bar of the thread on the right side.
Please post your feedback. Also THANKS is always welcome. Use the THANKS button (below right) if you feel that I deserve it.
Update - 24 April 2011 - New rooting method without needing to downgrade firmware.
Update - 3 May 2011 - Very simple way of installing Custom Thunderg Recovery
Update - 3 May 2011 - Added Simplified Guide to Root & install Custom Recovery on P500
i have done all steps but cannot boot in custom recovery may be pressing the keys wrong please help
Thank you very much for posting this! I think it's only missing a section for downgrading, and changing from one custom rom to another, and it's perfect!
I guess my memory card died.. The USB-MS Toggle doesn't launch anything on my PC, tried several times.Now what?
FnH84 said:
I guess my memory card died.. The USB-MS Toggle doesn't launch anything on my PC, tried several times.Now what?
Click to expand...
Click to collapse
Have you installed the drivers for the phone on your computer? If you haven't, your phone will not be detected when toggling usb mass storage.
saileshchowatia said:
i have done all steps but cannot boot in custom recovery may be pressing the keys wrong please help
Click to expand...
Click to collapse
Did you read the thread I have linked to at the end of the article? it may help you.
FnH84 said:
Thank you very much for posting this! I think it's only missing a section for downgrading, and changing from one custom rom to another, and it's perfect!
Click to expand...
Click to collapse
The procedure for downgrading the firmware is included in the article. The procedure is the same for installing any version of original firmware on the phone.
Procedure to change from one custom rom to another various with each rom.some may need a wipe while others might need repartitioning your sd card.
victortangocharlie said:
Have you installed the drivers for the phone on your computer?
Click to expand...
Click to collapse
Yes. It worked fine before. I tried to flash with CM7, and something went wrong. The whole SD-card is empty, works on another phone though. However, Windows will not recognize it no matter what I do
Do you mean to say that your sd card is empty our that you can't see the sd card contents on your computer?
victortangocharlie said:
Do you mean to say that your sd card is empty our that you can't see the sd card contents on your computer?
Click to expand...
Click to collapse
Both. I put the memory card on another phone and it said it was empty. Also, custom recovery says it's empty and from mount menu, I can see it keeps unmounting.
Have you tried another card on your phone?
victortangocharlie said:
Have you tried another card on your phone?
Click to expand...
Click to collapse
I managed to get the card work via another card reader. I put the zip files on it and trying again now. Hope it will work.
EDIT: It works!!!
nvm.....................
Glad to hear it.
Sorry for noob question, but after downgrade to 2.2, root, can I flash any rooted 2.2.1 ? And is there any?
Once you have rooted your phone, you can install any custom rom meant for p500. This includes all android versions. And, you don't have to apologise for being a noob, this thread is meant for noobs primarily. everyone has to start someplace. There are many rom's accessible on this forum including android versions 2.2 to 2.3.3. I suggest you try Nessy#Euridice ROM by Dookmatt. I am using it and it is easy to set up.it is based on android 2.2.2
Thanks,
So if there isn't any method for root on 2.2.1, how they managed to give us pre rooted 2.2.1 roms?
I seek the fastest and stable rom with OC, but Im used to CM7 tweaks,.so im interested in it the most. So is it usable? Beside cm7 which is the fastest?
Guess, you will have to ask the people who make the rom's. I don't know about the cm7 rom.haven't used it myself.
IFLPI said:
Thanks,
So if there isn't any method for root on 2.2.1, how they managed to give us pre rooted 2.2.1 roms?
I seek the fastest and stable rom with OC, but Im used to CM7 tweaks,.so im interested in it the most. So is it usable? Beside cm7 which is the fastest?
Click to expand...
Click to collapse
rooting a stock Rom is hard where as as rooting a custom made rom is easy because u only need the framework to create ur custom rom....
and about CM7 u can choose between many flavours.... its upto u ..
hi
hey man thanks for the wonderful tutorial!!
i just broght my phone 2weeks back. got it after lots of requests to dad!!
i wanna try all the stuff but im damn scared if i would brick my phone..
although i have the exact same phone as yours..unbranded indian optimus one with v10c
should i try it or is there a risk that ill brick it..?
if i brick it.. is there a chance that i can get it repaired? or will the lg ppl refuse to support me because i screwedwith it??
thanks in advance!!
This may void your warranty, cost you your soul, and cause your spouse to leave you - ALL OF WHICH I AM NOT RESPONSIBLE FOR!
So, if it's because you screwed up flashing something, bricked your tablet with an OTA update after you installed CWM, or whatever, this is how you get it back to its outta-da-box shape!
(Please note, this assumes you have both installed CWM on your DS7 AND have installed the latest SDK on your computer).
1. Download the three attached .img files
2. Boot into CWM (since there really isn't anything else you can do)
3. In CWM, mount your SD card (so that you can view files via USB)
4. Plug in your DS7 to your computer, and copy the three .img files to the root of your SD card
5. Unmount your SD card, but leave the USB cable plugged into computer
6. Mount as many things as you can (ie system, boot, etc)
7. Open up command prompt, and navigate to your Android/tools folder, and type "adb devices"
8. There should be a number that shows up, or a "?" - either at this point is fine
9. Type the following command:
Code:
adb shell
a hash tag should show up that looks like this:
Code:
#~
10. Now, type the follow two commands one at a time:
Code:
flash_image /dev/block/mmcblk3p2 /sdcard/boot_orig.img
flash_image /dev/block/mmcblk3p1 /sdcard/recovery_orig.img
11. now, select "reboot" from DWM to reboot your device. It should boot and say something like "Formating Misc", and then it will reboot repeatedly
12. Use something small to push the RESET button on the DS7 (it's next to the SD card slot)
Your screen should go blank
13. Now, press and hold both the POWER button and the VOLUME - button until the screen comes on saying that the "fastboot downloader" is booted
14. Copy the three .img files into the your Android/tools folder
15. Now type the following code:
Code:
fastboot devices
16. There should be a number that shows up, or a "?" - either at this point is fine once again
17. Now type the following commands one at a time. The first will take a while to complete - this is okay:
Code:
fastboot flash system system_orig.img
fastboot flash recovery recovery_orig.img
fastboot flash boot boot_orig.img
Now, if after every command a "finished." is given, along with the total time each command took, you may continue.
18. You may now type the triumphant command:
Code:
fastboot reboot
Which will reboot your device.
Give it a little bit to boot, but when all is done you should see the original T-Mobile boot animation and everything.
Special thanks to DJ_Steve, bogdi1988, and [email protected] for all your help!
Needed files:
system_orig.img
recovery_orig.img
boot_orig.img
[Edit]
For those users who need the original "flash_image.zip" file, I have uploaded it and it is available here.
PS: As an added note: **** you Koush! From all of the DS7 community!
Just what was needed
sent from somewhere
thanks but if you would of search there was a thread made already but i am sure the more the marrier
mooch777 said:
This may void your warranty, cost you your soul, and cause your spouse to leave you - ALL OF WHICH I AM NOT RESPONSIBLE FOR!
So, if it's because you screwed up flashing something, bricked your tablet with an OTA update after you installed CWM, or whatever, this is how you get it back to its outta-da-box shape!
(Please note, this assumes you have both installed CWM on your DS7 AND have installed the latest SDK on your computer).
1. Download the three attached .img files
2. Boot into CWM (since there really isn't anything else you can do)
3. In CWM, mount your SD card (so that you can view files via USB)
4. Plug in your DS7 to your computer, and copy the three .img files to the root of your SD card
5. Unmount your SD card, but leave the USB cable plugged into computer
6. Mount as many things as you can (ie system, boot, etc)
7. Open up command prompt, and navigate to your Android/tools folder, and type "adb devices"
8. There should be a number that shows up, or a "?" - either at this point is fine
9. Type the following command:
Code:
adb shell
a hash tag should show up that looks like this:
Code:
#~
10. Now, type the follow two commands one at a time:
Code:
flash_image /dev/block/mmcblk3p2 /sdcard/boot_orig.img
flash_image /dev/block/mmcblk3p1 /sdcard/recovery_orig.img
11. now, select "reboot" from DWM to reboot your device. It should boot and say something like "Formating Misc", and then it will reboot repeatedly
12. Use something small to push the RESET button on the DS7 (it's next to the SD card slot)
Your screen should go blank
13. Now, press and hold both the POWER button and the VOLUME - button until the screen comes on saying that the "fastboot downloader" is booted
14. Copy the three .img files into the your Android/tools folder
15. Now type the following code:
Code:
fastboot devices
16. There should be a number that shows up, or a "?" - either at this point is fine once again
17. Now type the following commands one at a time. The first will take a while to complete - this is okay:
Code:
fastboot flash system system_orig.img
fastboot flash recovery recovery_orig.img
fastboot flash boot boot_orig.img
Now, if after every command a "finished." is given, along with the total time each command took, you may continue.
18. You may now type the triumphant command:
Code:
fastboot reboot
Which will reboot your device.
Give it a little bit to boot, but when all is done you should see the original T-Mobile boot animation and everything.
Special thanks to DJ_Steve, bogdi1988, and [email protected] for all your help!
Needed files:
system_orig.img
recovery_orig.img
boot_orig.img
PS: As an added note: **** you Koush! From all of the DS7 community!
Click to expand...
Click to collapse
Thanked using the Thanks button and Thanks for your post!
Just to remind me a little as I may miss something,
why we **** Koush? It is not his fault that we stuck at CWM, or is it????
jiwengang said:
Thanked using the Thanks button and Thanks for your post!
Just to remind me a little as I may miss something,
why we **** Koush? It is not his fault that we stuck at CWM, or is it????
Click to expand...
Click to collapse
No its not his fault.. people shouldn't have tried to install the ota update while having cwr installed.. instead should have waited for a zip of the update that hell posted on behalf of did steve. As I have said if you have cwr you really can't get ota updates and install them the normal way. If the update was an update.zip you could flash through cwr but dell uses pgk files not zip.. so the only way to update is to wait for a dev to release a flashable cwr zip fike
Sent from my HTC Glacier using XDA App
The reason I made this post was so that we could have one concise, iD10t proof solution for people who were dumb like me. There's other posts, but you have to go back and forth to get the solution.
And the "Koush-****ing" was because of his unannounced abandonment of his projects, and those he was working with.
And thank you for the kind thanks!
Sent from my Dell Streak 7 using XDA App
mooch777 said:
The reason I made this post was so that we could have one concise, iD10t proof solution for people who were dumb like me. There's other posts, but you have to go back and forth to get the solution.
And the "Koush-****ing" was because of his unannounced abandonment of his projects, and those he was working with.
And thank you for the kind thanks!
Sent from my Dell Streak 7 using XDA App
Click to expand...
Click to collapse
Did he retire completely?
graffixnyc said:
Did he retire completely?
Click to expand...
Click to collapse
Think so!
From my CM7 UrBan Glacier
Hi,
I am the situation described above as I tried the OTA and am now stuck in CWR.
I followed the directions putting the 3 files on the root of my DS7 and am stuck at the following:
~ # flash_image /dev/block/mmcblk3p2 /sdcard/boot_orig.img
flash_image /dev/block/mmcblk3p2 /sdcard/boot_orig.img
failed with error: -1
~ #
Any ideas.....?
Thanks
SkI
Error 1
Error 1 means that the file is not where it is supposed to be. In this case on the SD card. Check and make sure that you have the right file, with the right file name on the root of your SD card and try again!
Good Luck
What does
"Error scanning partitions" means?...
jiwengang said:
What does
"Error scanning partitions" means?...
Click to expand...
Click to collapse
nvm, it is solved. don't use your own flash_image. use the stock one.
dj_ski69 said:
Hi,
I am the situation described above as I tried the OTA and am now stuck in CWR.
I followed the directions putting the 3 files on the root of my DS7 and am stuck at the following:
~ # flash_image /dev/block/mmcblk3p2 /sdcard/boot_orig.img
flash_image /dev/block/mmcblk3p2 /sdcard/boot_orig.img
failed with error: -1
~ #
Click to expand...
Click to collapse
+1 same here...
I find that at step 3... I mount sdcard... it shows on PC... I copy the 3 files to drive... unmount sdcard... mount everything else... run the other commands then get error... when I repeat the process I notice the files I copied are not there... ?
so I tried to adb push the files... they say they went thru correctly... but still get the same result as above...
any ideas?
dfspot said:
+1 same here...
I find that at step 3... I mount sdcard... it shows on PC... I copy the 3 files to drive... unmount sdcard... mount everything else... run the other commands then get error... when I repeat the process I notice the files I copied are not there... ?
so I tried to adb push the files... they say they went thru correctly... but still get the same result as above...
any ideas?
Click to expand...
Click to collapse
when you adp push to sdcard, make sure you mounted it already.
after that , it always help to adb shell ls /sdcard to make sure all files are there.
then you go to adb shell,
use the stock flash_image to flash. remember point to the path to flash_image
eg. flash_image /dev/block/mmcblk3p2 /sdcard/boot_orig.img
my understanding, if you don't mount sdcard, you canot see your sdcard FROM the tablet's perspective.
I mean, for table's flash_image to work, it has to be able to access its drive, in this case, is sdcard 's content.
so did you try leave sdcard mount and do the command above?
Hey Team...
can someone help me find the stock flash_image plz.....
I soooooooooooooo happy I was able to fix my Streak 7......yahooooooooo
I was missing the correct flash_image file which i took from the Galaxy Tab flash_image which is the same for the Dell and follow the direction and I now up again.......
Thanks guys
chris73 said:
I soooooooooooooo happy I was able to fix my Streak 7......yahooooooooo
I was missing the correct flash_image file which i took from the Galaxy Tab flash_image which is the same for the Dell and follow the direction and I now up again.......
Thanks guys
Click to expand...
Click to collapse
What command did you do.
Sent from my HTC Glacier using XDA App
chris73 said:
I soooooooooooooo happy I was able to fix my Streak 7......yahooooooooo
I was missing the correct flash_image file which i took from the Galaxy Tab flash_image which is the same for the Dell and follow the direction and I now up again.......
Thanks guys
Click to expand...
Click to collapse
do I need to push flash_image to my tablet?
If I remember correctly it needs to be in the nvflash folder
Sent from my Dell Streak 7 using XDA Premium App
If you are new to rooting your phone, there are simple ways to go about getting clockwork mod onto your LG thrill
You can root it easily with the 1 click root tool (I dont have the link on hand) after installing the LG Drivers from the LG Website.
Then, Download Rootexplorer, Rom manager (which i think is installed with 1 click root along with superuser)
First thing, download the recovery.img here after installing ADB guide is located here
After downloading recovery image, go to your pc's user folder C:\users\yourname and move it to there, that way there is no mistaking its location for adb
Now, on your phone you first need to go into root explorer, go to the /data folder, long click and go to permissions and select all available boxes and also make sure your device is in R/W mode not R/O mode.
Run CMD as administrator and do the following:
adb push recovery.img /data
then type:
SU
(this makes superuser active)
then:
dd if=/data/recovery.img of=/dev/block/mmcblk0p6 bs=4096
then after clockwork is flashed to finalize the settings type:
rm /data/recovery.img
reboot
Presto, Clockwork Mod is installed, remember you can access the clockwork menu via rom manager menu, or 3D+Volume Down +Power releasing the power button when the LG screen appears.
I will soon post onto this, how to update to gingerbread just making sure it works well on my own first. also, working on ICS as well.
Hope this helps anyone who has had trouble with it!
kobos311 said:
If you are new to rooting your phone, there are simple ways to go about getting clockwork mod onto your LG thrill
You can root it easily with the 1 click root tool (I dont have the link on hand) after installing the LG Drivers from the LG Website.
Then, Download Rootexplorer, Rom manager (which i think is installed with 1 click root along with superuser)
First thing, download the recovery.img here after installing ADB guide is located here
After downloading recovery image, go to your pc's user folder C:\users\yourname and move it to there, that way there is no mistaking its location for adb
Now, on your phone you first need to go into root explorer, go to the /data folder, long click and go to permissions and select all available boxes and also make sure your device is in R/W mode not R/O mode.
Run CMD as administrator and do the following:
adb push recovery.img /data
then type:
SU
(this makes superuser active)
then:
dd if=/data/recovery.img of=/dev/block/mmcblk0p6 bs=4096
then after clockwork is flashed to finalize the settings type:
rm /data/recovery.img
reboot
Presto, Clockwork Mod is installed, remember you can access the clockwork menu via rom manager menu, or 3D+Volume Down +Power releasing the power button when the LG screen appears.
I will soon post onto this, how to update to gingerbread just making sure it works well on my own first. also, working on ICS as well.
Hope this helps anyone who has had trouble with it!
Click to expand...
Click to collapse
All of this is already posted as is the instructions on how to update to gingerbread.
i have install CWM by as your guide. but when i use Rom Manager to Back up , message pop up that install CWM first to complete this action. i am new to these things.
Thanks
Nexus S & Galaxy Nexus one click root toolkit ! Unlock bootloader+CWM+Su(or)SuperSu
This tool will root you nexus s/Galaxy Nexus install su or super su and ClockWorkMod recovery!!
For Nexus S:4G,I9020T,I9023,I9020A.
Galaxy Nexus:GSM/Verizon/Sprint
Disclaimer!
Your warranty is now void.
I am not responsible for bricked or damaged devices
YOU are choosing to make these modifications.
Click to expand...
Click to collapse
DOWNLOAD
Click to expand...
Click to collapse
Current Version (Nexus S + Galaxy Nexus) 3.5: http://d-h.st/qaL
MIRROR:http://www.mediafire.com/download.php?1if2rvgpcte2rcs
Old versions:
3.0: http://d-h.st/mhO
2.0: http://dev-host.org/gcZ (nexus s only)
1.0: http://dev-host.org/bEE (nexus s only)
HOW-TO
Click to expand...
Click to collapse
just unzip the content and run the tool ! drivers are included in case you need them.
incase you had any problems try rerunning the tool,and if you got superuser/supersu app but you are unable to use root apps,update superuser/supersu from the play store then update the binary from inside the app.
CHANGELOG
Click to expand...
Click to collapse
V3.5
-added support for jelly bean
-few script optimization
-updated superuser and supersu
V3.0
-added support to galaxy nexus and all it's variants.
-added support to install super su.
-moved from *.bat to *.exe
-new icon
-su/super su, will now automatically flash no need to touch "install zip"
-skip bootloader unlock if you are already unlocked.
-update drivers
V2.0
-Removed "sticky.bat"
-modified su flashing script.
-the recovery now will stick automatically no need to flash any file after rooting or running any script.
V1.0
-initial release
ALL DATA WILL BE WIPED FROM DEVICE(only if bootloader is locked)
credits
-Chainfire for super su
-ChainsDD for superuser
-Pdanet for drivers
-Clockworkmod team for recovery
-my friend for the icon
am i going to loose everithing on USB storage ? or jjust sistem data ? i have to have a full rom right ?
raducux said:
am i going to loose everithing on USB storage ? or jjust sistem data ? i have to have a full rom right ?
Click to expand...
Click to collapse
if your bootloader is locked then yes you will loose everything on USB storage,if the bootloader is already unlocked you will not loose any data,you don't need to flash a rom after rooting the device as it will not wipe the system.
Hi, I installed the drivers on my computer and am currently running the run.bat file. It's saying my device is not found. I have USB Debugging on, and USB storage is on. Any ideas?
Sticky please
Can i replace CWR with newest img version?
PLEASE STICKY THIS THREAD ON TOP.
Romaniac said:
Hi, I installed the drivers on my computer and am currently running the run.bat file. It's saying my device is not found. I have USB Debugging on, and USB storage is on. Any ideas?
Click to expand...
Click to collapse
Turn off the usb storage,you just need usb debugging enabled if you turned on usb storage it will not work
stewie-droid said:
Can i replace CWR with newest img version?
PLEASE STICKY THIS THREAD ON TOP.
Click to expand...
Click to collapse
The tool includes the latest cwm img,but if you want to replace it with another one you can do,just make sure you rename it to same name of the img in the root tool folder,but make sure that the recovery you will use is compatible with the nexus s
After I execute run.bat the phone is rooted. I reboot using ClockWorkMod Recovery. Then, when I run sticky.bat and follow the instructions I get the following:
[email protected]:/ $ su
su
[email protected]:/ # rm /etc/installrecovery.sh
rm /etc/installrecovery.sh
rm failed for /etc/installrecovery.sh, No such file or directory
What should I be doing? Please help.
Ritwik7 said:
After I execute run.bat the phone is rooted. I reboot using ClockWorkMod Recovery. Then, when I run sticky.bat and follow the instructions I get the following:
[email protected]:/ $ su
su
[email protected]:/ # rm /etc/installrecovery.sh
rm /etc/installrecovery.sh
rm failed for /etc/installrecovery.sh, No such file or directory
What should I be doing? Please help.
Click to expand...
Click to collapse
The phone should booted normally when running the sticky.bat (On the home screen),there is nothing to worry about just Complete the instructions normally one of the two scripts will fail since the name of the file differ in gingerbread and ics,try this rm /etc/install-recovery.sh and continue the instruction it should work and clockworkmod recovery would stick.
Thanks for your reply. I used a FixRecovery.zip file from another thread and flashed it after executing run.bat again. Now I am able to boot into ClockWorkMod.
Ritwik7 said:
Thanks for your reply. I used a FixRecovery.zip file from another thread and flashed it after executing run.bat again. Now I am able to boot into ClockWorkMod.
Click to expand...
Click to collapse
My friend can you guide where i can find this .zip because i m facing the same problem.thank you in advance
Ok I got it to stick by using Root Explorer to mount it as read/write first then ran the sticky.bat. ICS is the rm /etc/install-recovery.sh command.
m.sabra said:
The phone should booted normally when running the sticky.bat (On the home screen),there is nothing to worry about just Complete the instructions normally one of the two scripts will fail since the name of the file differ in gingerbread and ics,try this rm /etc/install-recovery.sh and continue the instruction it should work and clockworkmod recovery would stick.
Click to expand...
Click to collapse
I tried this and when I want to do the sticky.bat, when I type the "rm /etc/install-recovery.sh" it sais rm failed for /etc/.., Read-only file system
I had the same problem with sticky.bat.
Once you 're done with run.bat and it reboots in cwm just flash fix-recovery.zip
http://forum.xda-developers.com/showthread.php?p=20432966&highlight=fix-recovery#post20432966
karx23 said:
I had the same problem with sticky.bat.
Once you 're done with run.bat and it reboots in cwm just flash fix-recovery.zip
http://forum.xda-developers.com/showthread.php?p=20432966&highlight=fix-recovery#post20432966
Click to expand...
Click to collapse
thanks ! added the link to the OP in case anyone had problems like this.
Argh, I seem to have successfully unrooted my Nexus S 9020t and had it rebooted back in, but while it was booting up again I accidentally pressed a button and it told me "error: device not found" twice followed by "<waiting for device>".
Unfortunately my phone has already been rebooted, but it still seems to be waiting for my device. I'm not sure if I can disconnect this device from USB while this is going on, so uh, what do I do?
Edit: Disconnected and reconnected the USB cable on the phone to see what would happen, and it seems to be ok. I'm still stuck on "waiting for device" though. Should I consider restarting the process again?
Edit Edit: Decided to just try to redo the process all over again...seems to have worked!
Updated tool to version 2.0 ! check the changelog in OP, it should solve all sticky recovery related problems,as i removed sticky.bat and now the recovery will stick automatically without the need of running any commands or flashing any fixes.
thanks for reporting problems and feedbacks
thank you for this
Okay, I've tried to run this but it always fails at flashing the recovery.. Any help?
Lelouche said:
Okay, I've tried to run this but it always fails at flashing the recovery.. Any help?
Click to expand...
Click to collapse
Ok first have you unlocked your bootloader when the tool asked you to use volume buttons to chose yes and unlock ? (If you did this you should see an unlocked lock under google logo when booting the phone) if you didn't just run the script again and unlock the bootloader.
Are the drivers installed properly ? When you connect the phone to the pc check device manager to see if the PC recognizes the phone (the drivers are included in the tool in case you need them .
And last check the root tool folder on your pc it should have a file called cwm.img if it doesn't then download the tool again.
SuperUser is not visible after the process
I am on stock ICS, I had previously unlocked the bootloader, then I did the whole process mentioned in this thread. It showed me the CWM menu but when I did the reboot, I couldn't find the superuser app. Then to test whether it is rooted or not, I installed titanium backup but it says the device isnt rooted. What to do now? I tried SuperOneClick but it doesn't seem to work.
Edit: Thanks guys, sorry. It was my mistake, I didnt do the whole process in a right way. It is working as expected.
Hello,
I tried installing a custom ROM on my 7310 and it had issues. I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop. I think I need to repartition, but when I click the repartition checkbox in ODIN I get an error.
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Thanks.
A few questions:
spazlon said:
I tried installing a custom ROM on my 7310 and it had issues.
Click to expand...
Click to collapse
What did you try to flash and how did you try doing it (CWM, ODIN, ...)?
What 'issues'?
I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop.
Click to expand...
Click to collapse
How far into the boot sequence does it get?
Are you able to get into recovery?
If so, what recovery do you have (Stock vs CWM)?
Have you tried seeing what is causing the boot-loop using adb?
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Click to expand...
Click to collapse
This is an action of last resort. Exhaust all other avenues first.
boscorama said:
What did you try to flash and how did you try doing it (CWM, ODIN, ...)?
What 'issues'?
Click to expand...
Click to collapse
I used CWM to flash AOSP 4.1.2. It seemed to work fine for a day or two, but then it needed charging (as normal). I let it charge over night and in the morning it had less battery. I figured the charger or cable were flaky so I tried another set on another outlet and same thing. Then it finally ran out of battery. I let it charge again over night and when I tried to turn it on it was really slow. The boot animation was only 1 frame every couple seconds. It would eventually boot all the way up, but it was still REALLY slow. So I went into CWM and reflashed the same ROM. Then I got a boot loop of the boot animation. I couldn't get into CWM any more, so then I went into download mode and flashed the official firmware and flashed it with ODIN.
boscorama said:
How far into the boot sequence does it get?
Click to expand...
Click to collapse
Now when I turn it on it just says, "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I can flash again with ODIN and it will get to the Samsung boot animation and just pulse SAMSUNG.
boscorama said:
Are you able to get into recovery?
If so, what recovery do you have (Stock vs CWM)?
Click to expand...
Click to collapse
If I hold power and volume down I can get into download mode or Samsung recovery, not CWM, and power with volume up doesn't do anything.
boscorama said:
Have you tried seeing what is causing the boot-loop using adb?
Click to expand...
Click to collapse
I don't know anything about adb and I'm not sure what I would be looking for. Is there a tutorial I can follow somewhere?
Thanks for any help!
This worked for me with similar problem
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.
Thanks! I'll give this a try when I get home. I'll let you know how it works out.
Don't ever try to 'repartion unless you really know what you're doing. You're soft bricked. Repartion and you'll hard brick.
I'd go back and get hc from sammobile and flash that with Odin. Ics has had some problems.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
jd1639 said:
Don't ever try to 'repartion unless you really know what you're doing. You're soft bricked. Repartion and you'll hard brick.
I'd go back and get hc from sammobile and flash that with Odin. Ics has had some problems.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
Agreed - my procedure avoids manual repartitioning - I tried lots of other procedures but none worked. I think my data partition had become corrupt because I kept getting error messages. My first try was to recover with my cwm recovery file I made originally but I kept getting back to the boot loop .
spazlon said:
Hello,
I tried installing a custom ROM on my 7310 and it had issues. I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop. I think I need to repartition, but when I click the repartition checkbox in ODIN I get an error.
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Thanks.
Click to expand...
Click to collapse
I always got something like that ...
After bootloop just go to recrovery mode then factory riset ... its 100% WORK
Sent from my GT-P7300 using xda premium
I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.
spazlon said:
I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.
Click to expand...
Click to collapse
Sorry - being a newbie myself I'm at a loss. It worked a charm for me.
spazlon said:
I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.
Click to expand...
Click to collapse
did a format /system before installing the custom roms? This is an important step.
prince93 said:
did a format /system before installing the custom roms? This is an important step.
Click to expand...
Click to collapse
This fixed it. Never had to do it with any of my other devices. CM10 loaded quickly after that. Loving how fast JB is!
Thanks!
Sent from my GT-P7310 using Tapatalk HD
It worked
mobjunky said:
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.
Click to expand...
Click to collapse
WOw! This fixed my Tablet! thank you ever so much!!
mjramos15 said:
WOw! This fixed my Tablet! thank you ever so much!!
Click to expand...
Click to collapse
mobjunky said:
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.
Click to expand...
Click to collapse
Gee thanks. This saved my tab. I'd almost given up on it and then voila.