Related
Hey,
I was wondering weather it's possible to replace the silver stripe which is around the SGS ??
If any one have done it or knows how to do it, please let me know...
I have tried searching, but didn't find anything useful...
Thanks in advance
Hey.. Anyone... Please help...
Sent from my GT-I9000 using XDA App
hi
I was interested in that too, I've got some dents and scratches on mine but
I don't think thats a job for the faint hearted.
I watched a youtube disassemble job and it looked to me like the silver bezel is bonded to the screen, that and the fact it scared the hell out of me how much it took to take the phone apart made me give up on that idea.
UP!
Anyone ?
Thanks
It's called a bezel. Think I remember seeing a thread in the accessories section.
replacing the front bezel involves removing a backing plate behind the screen, which most likely is glued to the screen/digitizer assembly.
Its much harder to remove than what you see in the below video.
Chances are you will break the screen or the glass. I had a spoilt home button and accidentally cracked the screen while trying to remove the screen to access the button assembly :crying:
I would avoid doing this I thought I could and ruined my phone there's they fragile Aileen mesh like strips under there ended up costing me £80 for a new screen unit!
Sent from my GT-I9000 running remICS-UX using XDA premium
When I press(with a bit more force) on the left side I hear creaking noise, is that normal or not?
I don't have raised glass problem.
jaroslavj said:
When I press(with a bit more force) on the left side I hear creaking noise, is that normal or not?
I don't have raised glass problem.
Click to expand...
Click to collapse
I have 2 Nexus 7. My Nexus 7 has a minor screen lift, but it's not noticeable. But yea it has the creaking noise near the upper left area. But then again I shouldn't like be putting that much force on the screen so I'm not too worried. My sister's Nexus 7 has no issues with either.
One of the mine did but it seems okay. That's why I think it is the back cover. Because of mine would squeak only if I held it from the back in certain areas. If I held if from another place on the back it wouldn't squeak like holding it from the other side and pushing down then the squeak would be gone. Mine usually would squeak right where the volume of buttons were.
Mine does the same no noticeable screen lift but it will creak if you press too hard on the left side
Sent from my DROID X2 using xda premium
yes.
on the left side of mine its the screen that is raised and creeks. on the right side i think its the back cover that is causing the creeking
I had the creak, it drove me nuts. My screen didn't lift at all. I returned it for a new one with no creak and no screen lift.
ferris2375 said:
I had the creak, it drove me nuts. My screen didn't lift at all. I returned it for a new one with no creak and no screen lift.
Click to expand...
Click to collapse
You had to apply not a lot of pressure if it drove you nuts right? And you RMA yours for that single reason?
jaroslavj said:
You had to apply not a lot of pressure if it drove you nuts right? And you RMA yours for that single reason?
Click to expand...
Click to collapse
I bought mine locally at Sam's, so it was just a matter of taking it back to the store. I bought a new one at Staple's first as they got a new shipment in...of only one.
There was enough movement to make me uncomfortable with it. Not only did it creak on that lower left side with some slight pressure, I could also feel movement when I pressed on the lower left of the screen. Not like squishy movement, just a weird shifting noise.
It's as if the case was a little too large or slightly warped somewhere. I didn't have to press very hard at all to make that sound and it did it naturally if I picked it up from the side. I tend to be OCD so something like that is just one of those things I would fixate on. I also had a dead pixel so the combo was enough to take a trip to Sam's to return it and Staple's for a new one. The difference is night and day with the new one though, it feels so much more sturdy without the noises.
I ordered a case to try and ignore it, but that is still on it's way so the return was kind of an impulse. Honestly if your screen is fine otherwise and you aren't OCD like me, it shouldn't be a deal breaker IMO. Unless a swap is easy, but things could always be worse.
Mine does same, no lift but squeaks with little pressure.
This squeak is because of that black tap that you can see once you open your nexus. At least this was the case with me. The sponge on the top of tape presses the tape when you press the device on left side. I fixed it by removing that foam. I am not recommending anyone to do it as that foam must be there for some reason either to cater for the flex in back cover or something but this was driving me crazy so I removed it. Please don't do it because I am saying this as you might have some different problem. This was my problem and this is how I fix it.
Sent from my Nexus 7 using xda premium
Mine has a slight creak but only when I apply a moderate-high amount of pressure at a certain spot, which I don't feel comfortable doing anyway. Haven't taken the back off but not sure if I will tbh, using a case can alleviate some display issues I.e. screen rising and sight creaks.
Sent from my Nexus 7 using xda premium
Mine has a clicking kind of sound on the left side and the glass depress's about 13/100ths of a MM with little to no force and it was an open box. I will bring mine back as soon as I find a store with another one in stock. I also didn't get the 25$ credit on my Google Play account because the person who bought and returned it took the credit...
My main concern is for dust getting under the glass. If the screen has any kind of travel like mine does I can only assume that it may suck some dust in and under the glass in-between the display and the glass. I don't know if the display is fused to the glass like my Gnex.
I've found that taking the back cover off and putting a single, small piece of electrical tape near the edges in the areas that squeek eliminates the creak. If you have creaking in areas other than the left area where there's screen lift, it's most likely caused by the back cover not fitting perfectly against he device. I put some small pieces of electrical tape in the top right corner and along the bottom right side of my Nexus 7, and it has just about eliminated all creaking.
Mine creaked around the edges til I pressed down hard on them to clip it more securely in place. I've no other issues and the screen is great.
Rik.
Sent from my Nexus 7 using Tapatalk 2
aindow said:
Mine creaked around the edges til I pressed down hard on them to clip it more securely in place. I've no other issues and the screen is great.
Rik.
Sent from my Nexus 7 using Tapatalk 2
Click to expand...
Click to collapse
This is what i done. Worked for me too.
Sent from my Nexus 7 using xda premium
My third replacement has creak with no lift at all.
Sent from my Nexus 7 using xda premium
My second Nexus 7 has no screen lift but the power button clicks loudly when depressed about as loud as a typical space bar. Loud enough that others in my office can tell when I turn the screen on. The vol. rocker does not make the same click sound it sounds and works like the first Nexus 7 I owned. I don't think the louder click from the power button is a big deal and will likely get less loud with use.
Hi!
I got my Nexus 7 yesterday and I dont have the raised glass but I have a creaking noise when pressing down the glass on the left side of the tablet. When I press the glass it creaks and after a second or so you here a popping sound. This is the only issue I have with my Nexus 7. You guys think I should return it and get a replacement or is this normal? It only happen when I press down harder than normal.
Doraso said:
Hi!
I got my Nexus 7 yesterday and I dont have the raised glass but I have a creaking noise when pressing down the glass on the left side of the tablet. When I press the glass it creaks and after a second or so you here a popping sound. This is the only issue I have with my Nexus 7. You guys think I should return it and get a replacement or is this normal? It only happen when I press down harder than normal.
Br D
Click to expand...
Click to collapse
I have the same problem and am trying to decide if its screen lift or just some weird noise. Advice guys?
Same problem - I've had this issue since I got my Nexus 7 two weeks ago and so far nothing terrible has happened.
I've had my lovely Xperia T for almost 2 weeks now and I've got a few concerns about the build quality and I'd like to see if I'm the only one with these issues:
1) I've noticed a few places on the back panel which exhibit a certain amount of creaking when I apply slight pressure. The worst areas are at the top left of the device behind the notification LED and between the SIM/Micro SD panel and the power button. This sound is quite irritating to me, especially for a brand new device.
2) There are a few areas along the edge of the matte black panel where the matte paint have been scratched off. Two of the corners have slight paint wear and around the headphone jack. Under the matte paint is a shiny black surface and it seems (so far) to be affecting the sharper edges or where the matte panel meets the metallic bezel. I'll try to take photos, but it's very small at the moment and might not be picked up due to it's dark colour.
Like I said, I've only had this phone less than a fortnight and it's already showing signs of wear even though I'm very careful with my devices.
Do any of you have any experiences like this?
Had mine for 2 and half weeks and have no sign of even being used. Don't have it in a case or anything. Where did you get it from.
Sent from my Xperia T using Tapatalk 2
Carphone Warehouse UK. I can live with these small paint chips but I'm concerned it'll only get worse with time
Sent from my LT30p using xda premium
daranx said:
I've had my lovely Xperia T for almost 2 weeks now and I've got a few concerns about the build quality and I'd like to see if I'm the only one with these issues:
1) I've noticed a few places on the back panel which exhibit a certain amount of creaking when I apply slight pressure. The worst areas are at the top left of the device behind the notification LED and between the SIM/Micro SD panel and the power button. This sound is quite irritating to me, especially for a brand new device.
2) There are a few areas along the edge of the matte black panel where the matte paint have been scratched off. Two of the corners have slight paint wear and around the headphone jack. Under the matte paint is a shiny black surface and it seems (so far) to be affecting the sharper edges or where the matte panel meets the metallic bezel. I'll try to take photos, but it's very small at the moment and might not be picked up due to it's dark colour.
Like I said, I've only had this phone less than a fortnight and it's already showing signs of wear even though I'm very careful with my devices.
Do any of you have any experiences like this?
Click to expand...
Click to collapse
Yep about to ask the same thing here... I cant believe that after 2 weeks of normal usage back matte covering is starting to peel at the corners. Its some kind of spray over a glossy plastic. Had galaxy ace for over a year and that stayed like new. Was very upset with this, so I ordered thin hard plastic case to cover that s***.
I got the phone from O2 ireland. James Bond and what not...but very disappointed as for the price.
Mine is exactly as you described it. Paint started to peel off at the top corners and the creak when pressed on the left corner. Really disappointed with Sony's built quality. Also the factory installed screen protector is showing some marks/light scratches. Does anyone know if it is possible to remove it as I would like to replace it with aftermarket ones. It seems to be glued to the screen.
Sent from my LT30p using Tapatalk 2
Protongti said:
Mine is exactly as you described it. Paint started to peel off at the top corners and the creak when pressed on the left corner. Really disappointed with Sony's built quality. Also the factory installed screen protector is showing some marks/light scratches. Does anyone know if it is possible to remove it as I would like to replace it with aftermarket ones. It seems to be glued to the screen.
Sent from my LT30p using Tapatalk 2
Click to expand...
Click to collapse
I have not removed it from the xperia t yet, but I have removed it from my past xperia devices with no problem at all, but it does need a knack to take it of
Sent from my LT30p using xda premium
I've been reading into this 'shatter proof' layer and I'd be curious to find out if anyone here has removed theirs already? How does it affect dust/smudges etc? I'm naturally a bit hesitant to attack my phone just yet.
A note on the creaking case; I've found a rather unprofessional way to resolve it and it's reduced the noise significantly. It's possible to wedge a thin piece of paper between the back panel and the bezel, so I trimmed a piece small enough to go ask the way inside as far as it can go and gently pushed it out of sight using a craft knife. I used a post-it note and made a strip about 1mm wide and 5mm long and this seemed to do the job.
Sent from my LT30p using xda premium
Mine is exactly as you described it too.
daranx said:
I've been reading into this 'shatter proof' layer and I'd be curious to find out if anyone here has removed theirs already? How does it affect dust/smudges etc? I'm naturally a bit hesitant to attack my phone just yet.
Sent from my LT30p using xda premium
Click to expand...
Click to collapse
Not so sure its a "Shatter proof" layer or just to keep any broken glass stuck together so you dont cut yourself. It may give some protection against shattering but as I have said before, I removed it from my x10 and my neo with no adverse effects at all. Still to do it yet on my T. The reason eing, soon that layer gets scratched and dull, then I will take it off and have a brand new screen, similar pricicple to the rip offs the F1 drivers use on their visors.
Mine creaks as does my wife's Xperia T. Really annoying at first, but I got a hard case from Amazon UK and its stopped most of it.
Just removed my built-in/factory-fitted screen protector or whatever you want to call it :laugh:
Gave it a good clean as it was very slightly tacky and now it looks much slicker with the screen off... it seems to attract less dust and it isn't as smear-prone as before. I prefer the naked glass feel and it seems ever so slightly more responsive. Kinda glad I took the plunge after being too chicken to do it lol
Good for you!! Did mine also today using a credit card. Started at the top where the speaker is as it had the least resistance. Came off quite easily.
Sent from my LT30p using Tapatalk 2
Are the front-panel logos on the Xperia T on the glass itself or on the shatterproof sheet? In other words, did the logos come off along with the sheet?
LesPaulGuitarPlayer said:
Are the front-panel logos on the Xperia T on the glass itself or on the shatterproof sheet? In other words, did the logos come off along with the sheet?
Click to expand...
Click to collapse
The sony and xperia logo remain on the phone after I took off the factory fitted screen protector
Silver sticker around camera lens.
A week in with my Xperia T and the sticker around camera lens has peeled away. Anyone else have same problem? Perhaps I'll need silver model paint in it's place.
same problem
had my xperia T for about 2 months now, i have been very careful with it, it hasnt been droped, or against anything sharp, the only thing it has had is the pulling in and out of my pocket every time i use it, as any phone should be designed to do, and the paint on all 4 corners is wearing off, mainly on the left side, i belive this to be the angle that it usually is in my jeans pocket causing it to scratch.
as a matter of intrest whats the cover on warenty for something like this? because the manufacture could say its not their fault,
lordadamthird said:
had my xperia T for about 2 months now, i have been very careful with it, it hasnt been droped, or against anything sharp, the only thing it has had is the pulling in and out of my pocket every time i use it, as any phone should be designed to do, and the paint on all 4 corners is wearing off, mainly on the left side, i belive this to be the angle that it usually is in my jeans pocket causing it to scratch.
as a matter of intrest whats the cover on warenty for something like this? because the manufacture could say its not their fault,
Click to expand...
Click to collapse
There is already a thread about this problem, and yes, it's covered by warranty. See http://forum.xda-developers.com/showthread.php?t=2031472
Sent from my LT30p using xda app-developers app
I just noticed that the top edge of my screen isn't flush with the speaker. It's slightly raised and my finger sorta nicks it every time I swipe down. Is this a normal thing or a slight defect?
Sent from my HTCONE using xda premium
blackmamba0730 said:
I just noticed that the top edge of my screen isn't flush with the speaker. It's slightly raised and my finger sorta nicks it every time I swipe down. Is this a normal thing or a slight defect?
Sent from my HTCONE using xda premium
Click to expand...
Click to collapse
On the left side? If so I have the same thing.
Sent from my HTCONE using xda app-developers app
racrickey said:
On the left side? If so I have the same thing.
Sent from my HTCONE using xda app-developers app
Click to expand...
Click to collapse
It goes all the way across but yeah, more so on the left side for me too.
Sent from my HTCONE using xda premium
blackmamba0730 said:
I just noticed that the top edge of my screen isn't flush with the speaker. It's slightly raised and my finger sorta nicks it every time I swipe down. Is this a normal thing or a slight defect?
Sent from my HTCONE using xda premium
Click to expand...
Click to collapse
It seems that it is an issue. I have the silver and its very minimal and isn't an issue for me. I've since ordered the black as a replacement (wanted black in the first place) and is much worse and not acceptable to me, and the top speaker grill has 3 scratches on it so I called sprint and they are processing an order to replace the black.
blackmamba0730 said:
I just noticed that the top edge of my screen isn't flush with the speaker. It's slightly raised and my finger sorta nicks it every time I swipe down. Is this a normal thing or a slight defect?
Sent from my HTCONE using xda premium
Click to expand...
Click to collapse
I think its a lack of quality control. Some are flush, some aren't. If it bothers you, you may want to see about exchanging it and be sure to point out that you believe it is a manufacturer's defect (this will be key in avoiding the Sprint restocking fee assuming you bought from Sprint). Another thing to consider is that if you intend to put a screen protector on the device, screen protectors only cover the glass and not the speaker grills. Therefore the "nick" you describe will be present even if you have a flush screen because the screen protector will create a non-flush edge (and the "nick" will be even larger if you apply it to your current device).
batch problem maybe, lack of quality control.
I have the opposite issue at the bottom. The screen appears to be sunken in ever so slightly on the sides, while the speaker is flush with the sides and its flush at the top. I can feel it somewhat, but this is my second unit after a dead pixel replacement so I'm probably going to roll with it because the replacement could have bigger issues.
Just picked mine up today. Also noticed the left side of the screen isn't completely flush. The right side is a little closer, but the left side is the worst.
Sent from my HTCONE using xda premium
Got my Black replacement yesterday. Very slight raised glass on the top left but it's so minimal I'm not going to complain. I guess 3rd ones a charm. Just sucked dealing with Sprints telesales dept for 2 weeks trying to get a acceptable device.
I'm upset they rushed this phone out without thoroughly looking over It better.. I got the unflush screen, the gap up top.. argued with a sprint rep today about the gap and he opened a new HTC and it had the same problem.. so another rep said the gap is for better antenna signal lol
Sent from my HTCONE using Tapatalk 2
I have a black one. It is the same. Top left is noticeable. It isnt really bothering me till I get some scratches or nicks in the anodization if u know what I mean.
Sent from my HTCONE using xda app-developers app
My HTC one also has a raised screen on the entire top side but the bottom side is flush and everything else about the build quality is good. Eventually, it started bothering me and I ordered a replacement phone (wirefly.com and within my two weeks). The replacement phone had the same problem and it also had a huge gap between the aluminum and white plastic (which my original didn't have). So I ordered another replacement phone and this time the screen is raised on the left top side and lowered on the top right side meaning it's slanted in reference to the body of the phone. And there's a smaller gap between the aluminum and white plastic. I feel like this is going to be an endless cycle. What should I do?
I love the phone but this is bad quality control on HTC's side.
bhaktasa said:
My HTC one also has a raised screen on the entire top side but the bottom side is flush and everything else about the build quality is good. Eventually, it started bothering me and I ordered a replacement phone (wirefly.com and within my two weeks). The replacement phone had the same problem and it also had a huge gap between the aluminum and white plastic (which my original didn't have). So I ordered another replacement phone and this time the screen is raised on the left top side and lowered on the top right side meaning it's slanted in reference to the body of the phone. And there's a smaller gap between the aluminum and white plastic. I feel like this is going to be an endless cycle. What should I do?
I love the phone but this is bad quality control on HTC's side.
Click to expand...
Click to collapse
Right now, its pretty much luck of the draw as to if you can get a flush one or not. I guess it will also depend on how much patience you have as to how many times are you willing to do an exchange. Also, just realize that if you do finally get a unit with a flush screen, if you put a screen protector on it, it will only cover the glass and not the speaker grills. This means that the screen protector will then create an edge/lip at the top and bottom of the glass panel so again, it will not feel flush/smooth due to the screen protector.
Marty said:
Right now, its pretty much luck of the draw as to if you can get a flush one or not. I guess it will also depend on how much patience you have as to how many times are you willing to do an exchange. Also, just realize that if you do finally get a unit with a flush screen, if you put a screen protector on it, it will only cover the glass and not the speaker grills. This means that the screen protector will then create an edge/lip at the top and bottom of the glass panel so again, it will not feel flush/smooth due to the screen protector.
Click to expand...
Click to collapse
I don't use a screen protector so that's not a problem. I just want a good phone. How is that I can get three phones that look completely different in build from the same company? That just seems so odd to me and looks bad on HTC's side. I feel like if this is going to be an endless cycle, I might make the switch to a different phone.
bhaktasa said:
I don't use a screen protector so that's not a problem. I just want a good phone. How is that I can get three phones that look completely different in build from the same company? That just seems so odd to me and looks bad on HTC's side. I feel like if this is going to be an endless cycle, I might make the switch to a different phone.
Click to expand...
Click to collapse
It has been said that, that's why the black version' s release was delayed...to correct some minor design flaws, such as the ones you are having problems with....
Hope this helps...
w8setter said:
It has been said that, that's why the black version' s release was delayed...to correct some minor design flaws, such as the ones you are having problems with....
Hope this helps...
Click to expand...
Click to collapse
I've had three black HTC Ones and all had the same issue of the screen not being flush with the speaker grills. The issue was definitely not corrected in the black version.
---------- Post added at 10:00 AM ---------- Previous post was at 09:53 AM ----------
bhaktasa said:
I don't use a screen protector so that's not a problem. I just want a good phone. How is that I can get three phones that look completely different in build from the same company? That just seems so odd to me and looks bad on HTC's side. I feel like if this is going to be an endless cycle, I might make the switch to a different phone.
Click to expand...
Click to collapse
I also got frustrated with HTC quality control issues and some of the software choices they made in Sense 5 and so I am currently trying out a Galaxy S4 (haven't decided if I am going to keep it yet). Its not quite as snappy as the One but its acceptable to me as far as speed goes. No real quality control issues I've noticed and enjoying all the features Samsung has packed into this device. Both devices are great but each has its tradeoffs.
Hello everybody! I do not know where to begin but hope this forum.xda-developers.com will be useful for me. warmest regards from annonce escorte - www.goldendolls.com
Ok so I have the silver HTC One and as much as I love it, I can't help but think the front would look bad-ass with the black speaker grills...
I was wondering if anyone has any experience replacing their speaker grills, I remember seeing a drop test video and it popped off. The guy in the video mentioned how it didn't clip back on, it was glued on.
I think if it was easy enough to get a stanley blade in between the grill and the plastic it could just pop off (mine has a gap so it could be quite easy) then it would also help in the future if any scratches happen, just to replace them again...
Thoughts?
thats a good idea, itll be great to know if the speaker grills are repleacable, as they are slightly raised on most phones
I'm just worried incase I order the replacment parts and they are not the same quality as the real HTC One parts. Is there a site that sells genuine parts? They would need to ship to the UK for me though...
Are you out of your mind?
If you are, I'd recommend sandpaper tape and some spray paint. That would probably be easier than disassembly. Maybe even some black nail polish.
Sent from my HTC One using xda premium
couped said:
Are you out of your mind?
If you are, I'd recommend sandpaper tape and some spray paint. That would probably be easier than disassembly. Maybe even some black nail polish.
Sent from my HTC One using xda premium
Click to expand...
Click to collapse
I dont think it will be as bad as you think, this is the video I was talking about:
http://youtu.be/KwE9PGDnlvs?t=1m51s
I know the top may be more difficult to get off because of the camera and I think I will wait a few more months to see if anyone does drop their One and the top part pops off... But it would be interesting to know because this could be useful to those who get any real bad damage to their speaker grills...
The speaker grills are glued to the housing, Removing them shouldn't be hard
Do it and get us some pics
I'm doing it. Are you sure about the glue? I also started a thread about it a couple of days ago.
robt772000 said:
I'm doing it. Are you sure about the glue? I also started a thread about it a couple of days ago.
Click to expand...
Click to collapse
The bottom one is definitely glued, I am not sure about the top one though
Im interested...
Barca009 said:
Ok so I have the silver HTC One and as much as I love it, I can't help but think the front would look bad-ass with the black speaker grills...
I was wondering if anyone has any experience replacing their speaker grills, I remember seeing a drop test video and it popped off. The guy in the video mentioned how it didn't clip back on, it was glued on.
I think if it was easy enough to get a stanley blade in between the grill and the plastic it could just pop off (mine has a gap so it could be quite easy) then it would also help in the future if any scratches happen, just to replace them again...
Thoughts?
Click to expand...
Click to collapse
I agree that the black would look pretty cool. Let us know how this turns out! and take pictures of the process. I myself am curious whats behind the top grill, my speaker on the top is starting to crackle horribly i want to know if it would be possible to replace.
One of mine (the bottom grill) has a small chip in it that really annoys me, so i have ordered a new set. Postage to the UK is quite expensive, but the total was only £24. Not that bad considering its an original part I guess.
Removing the grills shouldnt be too hard, just heat them up with a hot air gun, being careful not to 'cook' the phone and carefully prise the grill up. The gap most people have in the case may be a help here. The new one should just press on. Warm it up, press it down and hold it firmly until cool, with a clamp or strong bulldog clip if you can.
Etradesupply.com sells almost everything for HTC one just so everyone knows if they didn't, u also have a tiny chip in my lower speaker grill, but my case hides it for now so I'm not super worried, but I would love to know if this is possible!!
Sent from my HTC One using xda premium
The grills and the SIM tray are about the only things you can replace. They sell screens, but there is no realistic way to replace them. Even if you could open the phone without marking it, putting it back together is almost impossible.
rovex said:
One of mine (the bottom grill) has a small chip in it that really annoys me, so i have ordered a new set. Postage to the UK is quite expensive, but the total was only £24. Not that bad considering its an original part I guess.
Removing the grills shouldnt be too hard, just heat them up with a hot air gun, being careful not to 'cook' the phone and carefully prise the grill up. The gap most people have in the case may be a help here. The new one should just press on. Warm it up, press it down and hold it firmly until cool, with a clamp or strong bulldog clip if you can.
Click to expand...
Click to collapse
Just for clarification, did you order this from etrade supply? do you have it yet and how is the quality...?
Regards
Zak
Etradesupply quality is very good. I order parts from them and never have an issue.
Heat gun or hair dryer to loosen up the glue should help.
Sent from my HTC One using xda app-developers app
Curious to see if you went through with this.
Sent from my HTC One using xda premium
I bought some etrade silver speaker grills but no longer need them.
If possible please share the whole process heating , removing and fixing the top and bottom speaker grill. Thanks !
Sent from my HTC One using xda app-developers app
Just a tip, do not "paint" the grill. It's impossible to do without stuffing up the holes anyway.. And paint does not stick to aluminium.
You need to anodise aluminium.
Google how to do it but in a nutshell..
1) chemically clean existing aluminium to remove all traces of colour /surface protection. 2)Anodise it to required colour or clear colour
This not only gives you the look you want but makes the surface very hard.
Anodising also is not "on" the surface but part of it so it won't scratch off, block holes etc.
Bare aluminium is very soft and WILL oxidise and go dull. Apart from living in a vacuum or learning to breathe argon gas, you can't stop it.
Anodising MAKES aluminium oxidise and then fill the surface with a dye. This prevents further oxidisation.
Cheers, Marty
Sent from my HTC One using Tapatalk 4 Beta
any luck with replacing the speaker grills?
Just a heads up
I asked about this a different thread and one of the people that replied told me that only the bottom grill is glued in. He said the top is actually screwed in from the back before the back cover is put on. I cant confirm if he was correct, but still good info for anyone planning to try something like this. Can anyone confirm that has purchased these if there are threads in the top grill for it to be screw in?