[Q] What to do after Odin Master Clear - Captivate Q&A, Help & Troubleshooting

Hey all,
I'm new to this rooting business, and to make a long story short, after I finally figured out how to root 2.3.5 Gingerbread, I tried flashing a ROM or two to see how they work. I messed up while flashing, and resorted to using Odin3 One-Click downloader to completely clear everything on my phone. This brought me back to the 2.1 Eclair version, and now I am wondering how can I upgrade it back go 2.3? I tried using Kies, but it gets stuck at the MTP stage on my phone. Any ideas or suggestions would be greatly appreciated, I'd rather not be stuck on 2.1 even though it was my own fault

you need to go under the development section and look for the sticky with Odin one click and download a gb version that has cwm injected into the kernel
Sent from my SGH-I897 using XDA Premium App

Thanks for the help. I looked around for a few hours but couldn't figure it out. The problem is I can't go into Recovery mode, and the only option seems to be the abd, which I'm not confident in doing haha.

kenwang2688 said:
Thanks for the help. I looked around for a few hours but couldn't figure it out. The problem is I can't go into Recovery mode, and the only option seems to be the abd, which I'm not confident in doing haha.
Click to expand...
Click to collapse
Can you get into download mode? If not, you screwed yourself over by flashing Eclair bootloaders. I think you would need adb in that case.

korockinout13 said:
Can you get into download mode? If not, you screwed yourself over by flashing Eclair bootloaders. I think you would need adb in that case.
Click to expand...
Click to collapse
I cannot get into download mode...when I plug in the USB it just goes directly into charging the battery. Do you know of any good videos or links that I can use for adb?

You have to hold buttons to get to DL

b-eock said:
You have to hold buttons to get to DL
Click to expand...
Click to collapse
Yeah, I press the Vol up and down and then plug it in, but it just shows the charging signal

Is there a kernel you can flash for 2.1 that has an extended power menu? That would allow you to select a reboot into download mode. But I have no idea if that kernel exists since 2.1 is a long long time ago. (what a miserable time that was)

So I managed to flash a Heimdall One Click 2.2 version, but the problems I have with that are that it doesn't let me connect to neither Wifi nor 3G. I was going to try to upgrade it to 2.3, but when I connect it to Kies, it gets to the point where it talks about upgrading my software, but when the process of upgrading actually begins, it gets stuck and says it could not complete the upgrade. Any ideas of what to do now?
Thanks for all the previous help

capocaccia said:
Is there a kernel you can flash for 2.1 that has an extended power menu? That would allow you to select a reboot into download mode. But I have no idea if that kernel exists since 2.1 is a long long time ago. (what a miserable time that was)
Click to expand...
Click to collapse
kernels don't contain the power menu at all...
that is in the framework-res.apk, the framework.jar and the android.policy.jar. which is contained in the rom, be it stock or custom.
kenwang2688 said:
So I managed to flash a Heimdall One Click 2.2 version, but the problems I have with that are that it doesn't let me connect to neither Wifi nor 3G. I was going to try to upgrade it to 2.3, but when I connect it to Kies, it gets to the point where it talks about upgrading my software, but when the process of upgrading actually begins, it gets stuck and says it could not complete the upgrade. Any ideas of what to do now?
Thanks for all the previous help
Click to expand...
Click to collapse
ditch kies...its garbage.
just grab a stock gingernread package from HERE since you used odin one click to 2.1 (that flashed eclair bootloaders, which is why your button combos were mesed up) you will need a a gingerbread package WITH bootloaders.

studacris said:
kernels don't contain the power menu at all...
that is in the framework-res.apk, the framework.jar and the android.policy.jar. which is contained in the rom, be it stock or custom.
ditch kies...its garbage.
just grab a stock gingernread package from HERE since you used odin one click to 2.1 (that flashed eclair bootloaders, which is why your button combos were mesed up) you will need a a gingerbread package WITH bootloaders.
Click to expand...
Click to collapse
Since I upgraded to 2.2 with Heimdall, am I still able to use the Odin?

Yes, you can still use Odin.
You may need to uninstall the heimdall divers, then reinstall the Samsung ones first.
For Future connection issues consult this thread

Related

[Q] need help

I rooted my phone like couple of month ago, then I updated the new AT&T partial update then today, I ran the froyo 2.2 update through the rom manager everything went ok but when i tried to use the rom manager again to restore my app. it restored then when it rebooted it came to the AT&T screen then froze, i tried to put it in recover mood but i could not, I had to take the battery off to force to power off, then when i put the battery back and power on it only come to the AT&T screen and froze. I do not know what to do?
1. Download Odin One Click to Stock JF6.
2. Launch Odin
3. Remove the battery from your phone
4. Plug the phone into the computer
5. Hold down both volume buttons
6. Put the battery in the phone while still holding both volume buttons
After step 6 the phone should enter download mode and Odin should have a box that says: COM:# and then press start. It should flash you back to JF6.
I Could put it in the download mode but everytime i use the odin it fails
haithamelbedawy said:
I Could put it in the download mode but everytime i use the odin it fails
Click to expand...
Click to collapse
Is Odin able to recognize your phone when you plug it in?
Try running Odin as an administrator.
i even tried that and it did not work out
haithamelbedawy said:
i even tried that and it did not work out
Click to expand...
Click to collapse
Are you using a rear usb port on your pc? Do you have the correct drivers for Odin?
finally i been able to reset the phone to a factory restrore, I did not do anything different than what I used to but i guyess I just needed to keep trying.
Now if I want to install the froyo 2.2 on my phone what do you recommend me to do?
Thanks all for your help
haithamelbedawy said:
finally i been able to reset the phone to a factory restrore, I did not do anything different than what I used to but i guyess I just needed to keep trying.
Now if I want to install the froyo 2.2 on my phone what do you recommend me to do?
Thanks all for your help
Click to expand...
Click to collapse
Go to development, select a rom, download the .zip file, but do NOT rename it to update.zip and just copy it over to the root of the sd card.
I would recommend reading!
1. Root
2. Download Rom Manager
3. Flash CWM
4. Reboot into recovery
a. Install packages
b. It'll bring you back to 2e recovery
c. Install packages again and it'll load CWM Recovery
5. Install .zip from sd card and select the rom.zip
Make sure you have the three button recovery or can use a jig before flashing Froyo, I recommend Perception ROMS, they have most bugs fixed and DG gives great support, also he made a nice kernel. The ROM is I9000 Froyo based and it works great. I've tried out several other ROMS but some have too many bugs, for me, or are too vanilla. I ran Tayutama's ROM for quite a while. I am waiting for CM6.1 to be less buggie, I'd love to try it but I need a working phone.
Can I be able to run Froyo 2.2 on my phone without rooting my phone?
haithamelbedawy said:
Can I be able to run Froyo 2.2 on my phone without rooting my phone?
Click to expand...
Click to collapse
yes
http://forum.xda-developers.com/showthread.php?t=797282
but i have to ask, WHY??
Just wanted to know, you do not recommend it or what is your opinion?
haithamelbedawy said:
Just wanted to know, you do not recommend it or what is your opinion?
Click to expand...
Click to collapse
there are much better options than the leaked FroYo. custom roms have been streamlined, and crafted together to give us a better FroYo experience. i would recommend just about ANY custom rom over the leaked 2.2
do you recommend a specific one?
i did that and it never came back could not get to recovery, ithink that if you do get a second chance, be sure that you are in usb debugging mode first
ronf1011 said:
i did that and it never came back could not get to recovery, ithink that if you do get a second chance, be sure that you are in usb debugging mode first
Click to expand...
Click to collapse
Thanks for the advice
haithamelbedawy said:
do you recommend a specific one?
Click to expand...
Click to collapse
right now i am on assonance rom, and i will probably bounce around because i like to try them all out.

[Q] Ahhh!! I think i phucked my cappy!!! HELP!

Tried all day using the search tool but couldnt find anything like this.
Tried to install continuum 6.1 on my cappy from a previous froyo build. Odin said pass on the kernel but now my phone boots to the att screen, then a fuzzy, static-like screen then promptly reboots to do it all over again. I can get into download mode but cant boot the phone normaly. Help would be appreciated. Thanks for helping a noob guys.
Did you flash Gingerbread bootloaders? like Cezar says too?
Sounds like a bootloop
Sent from a happy phone using XDA Premium App
savagefurai said:
Tried all day using the search tool but couldnt find anything like this.
Tried to install continuum 6.1 on my cappy from a previous froyo build. Odin said pass on the kernel but now my phone boots to the att screen, then a fuzzy, static-like screen then promptly reboots to do it all over again. I can get into download mode but cant boot the phone normaly. Help would be appreciated. Thanks for helping a noob guys.
Click to expand...
Click to collapse
If you can get to download mode, you're not out of luck. Go to the ODIN3 One-click and you should be able to get yourself back to a stock state where you can start clean.
Quick warning - if the rom you were trying to flash had the GB bootloaders, be extremely careful. The one-click above will overwrite the bootloaders, and if something comes unplugged during that time, you will be in need of JTAG service.
jmtheiss said:
If you can get to download mode, you're not out of luck. Go to the ODIN3 One-click and you should be able to get yourself back to a stock state where you can start clean.
Quick warning - if the rom you were trying to flash had the GB bootloaders, be extremely careful. The one-click above will overwrite the bootloaders, and if something comes unplugged during that time, you will be in need of JTAG service.
Click to expand...
Click to collapse
I don't think he did flash Bootloaders BUT if he did DO NOT use 3 button fix 1 click that will hard brick your phone.
prbassplayer said:
I don't think he did flash Bootloaders BUT if he did DO NOT use 3 button fix 1 click that will hard brick your phone.
Click to expand...
Click to collapse
Very true. I've seen several people use the wrong one, and the naming convention of ODIN3 and ODIN 3-Button doesn't really help that.

[Q] Captivate Bricked after Odin One Click

Hello. I have searched the forums and have not really found out an answer to my question. Earlier in the week I tried installing Andromeda with an ursa minor kernal I believe? (I was following a tut on youtube) I succesfully got ursa minor on my phone but the tutorial failed to mention I had to put Andromeda on the internal sd card to flash it. (first time trying to flash a rom so big noob). I decided to go back to stock and retry using Odin One Click. Odin bricked my phone because it is build number 1108 :/ I have an infinite ATT world phone boot loop because of this. I will be trying to make a jig/buying one soon to get back into download mode to fix this. I am not sure exactly what I am supposed to do once I am in download mode. I want to get back to stock. Obviously Odin One Click doesn't work because of my build number. What steps should I follow to go back to froyo 2.2 and to retry? Please help I am just not sure.
yakobo said:
Hello. I have searched the forums and have not really found out an answer to my question. Earlier in the week I tried installing Andromeda with an ursa minor kernal I believe? (I was following a tut on youtube) I succesfully got ursa minor on my phone but the tutorial failed to mention I had to put Andromeda on the internal sd card to flash it. (first time trying to flash a rom so big noob). I decided to go back to stock and retry using Odin One Click. Odin bricked my phone because it is build number 1108 :/ I have an infinite ATT world phone boot loop because of this. I will be trying to make a jig/buying one soon to get back into download mode to fix this. I am not sure exactly what I am supposed to do once I am in download mode. I want to get back to stock. Obviously Odin One Click doesn't work because of my build number. What steps should I follow to go back to froyo 2.2 and to retry? Please help I am just not sure.
Click to expand...
Click to collapse
You'll have to use the full Odin program and grab a stock ROM from the development section. Once your in download flash stock ROM with through Odin or heimdall. I'm not next to my computer so I don't feel like fishing for links ..but should be fairly easy!
Sent from my SGH-I897 using xda premium
yakobo said:
Hello. I have searched the forums and have not really found out an answer to my question. Earlier in the week I tried installing Andromeda with an ursa minor kernal I believe? (I was following a tut on youtube) I succesfully got ursa minor on my phone but the tutorial failed to mention I had to put Andromeda on the internal sd card to flash it. (first time trying to flash a rom so big noob). I decided to go back to stock and retry using Odin One Click. Odin bricked my phone because it is build number 1108 :/ I have an infinite ATT world phone boot loop because of this. I will be trying to make a jig/buying one soon to get back into download mode to fix this. I am not sure exactly what I am supposed to do once I am in download mode. I want to get back to stock. Obviously Odin One Click doesn't work because of my build number. What steps should I follow to go back to froyo 2.2 and to retry? Please help I am just not sure.
Click to expand...
Click to collapse
This is a Odin 1 click for KB1 2.2 stock. After that follow any roms instructions except if it says stock 2.1 ignore it and assume its stock 2.2
I was wondering if I should follow this thread??
http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36
Might I ask do you need to get to 2.1?
prbassplayer said:
Might I ask do you need to get to 2.1?
Click to expand...
Click to collapse
When I got my phone (about a two weeks ago) it came with 2.2 already on the phone. I don't need to get to 2.1 but I was thinking I'd go to 2.1 and then upgrade to 2.2 using att? If I can?
But why? If you got it as is and its stock its att's 2.2. At any rate If your so inclined on flashing 2.1 the one you mentioned thats using full Odin with pit should work. I suggest doing it if and only if you have that jig handy. Also keep in mind that .tar probably has bootloaders in it (wich is a risk you really dont need to take) just my 2 cents
prbassplayer said:
This is a Odin 1 click for KB1 2.2 stock. After that follow any roms instructions except if it says stock 2.1 ignore it and assume its stock 2.2
Click to expand...
Click to collapse
Links in that thread seem to be broken:/ So I suppose I can't use that.
Ive never used this one but it is also a KB1 2.2 KB1
My ultimate goal is to get Andromeda3 on my cappy. It seems to be a good rom. Could I just flash that using oden? (put it in the pda slot) or will that not work until I go back to stock?
With this new thread you linked me to, Just put in odin and I should be good to go? Thank you for your help by the way.
Ive never used that rom. Follow their instructions and assume stock is 2.2 for you. Also The original link i sent you should have worked. Aperrantly mediafire.com is having issues tonight.
installing Andromeda3 doesnt require going back to stock, 2.2 or 2.1.
ODIN flash a custom CWM kernel
boot to recovery
flash rom
thats it
Pirateghost said:
installing Andromeda3 doesnt require going back to stock, 2.2 or 2.1.
ODIN flash a custom CWM kernel
boot to recovery
flash rom
thats it
Click to expand...
Click to collapse
I can't because I bricked my cappy. i can't go into recovery right now. I need a jig to get back into download mode to fix it.
prbassplayer said:
Ive never used that rom. Follow their instructions and assume stock is 2.2 for you. Also The original link i sent you should have worked. Aperrantly mediafire.com is having issues tonight.
Click to expand...
Click to collapse
Once I get my jig hopefully mediafire is up and I can download from the first link you sent me. That seems to be my best bet right now. Thank you for your help. I sure hope I can get my phone backXD
yakobo said:
I can't because I bricked my cappy. i can't go into recovery right now. I need a jig to get back into download mode to fix it.
Click to expand...
Click to collapse
you are stuck in a boot loop right?
if you power your phone off, hold down both vol buttons and hold down the power button until the ATT screen comes up, let go, does it not go into recovery mode?
or
download mode:
power off, while holding both vol buttons, plug in usb. does that not work?
yakobo said:
My ultimate goal is to get Andromeda3 on my cappy. It seems to be a good rom. Could I just flash that using oden? (put it in the pda slot) or will that not work until I go back to stock?
With this new thread you linked me to, Just put in odin and I should be good to go? Thank you for your help by the way.
Click to expand...
Click to collapse
Get ursa minor back on your phone, then mount usb in mounts and storage, then copy the Andromeda3 zip to the drive. You were almost there.
Fish around in the usb port with 301kOhms of resistance from radio shack. You will hit pins 4 abd 5 and you will be in download mode.
Pirateghost said:
you are stuck in a boot loop right?
if you power your phone off, hold down both vol buttons and hold down the power button until the ATT screen comes up, let go, does it not go into recovery mode?
or
download mode:
power off, while holding both vol buttons, plug in usb. does that not work?
Click to expand...
Click to collapse
No:/ no button combos work to get me in recovery or download mode. Getting a jig (hopefully today) so I can fix all this. Yes it is in a boot loop
AdamOutler said:
Get ursa minor back on your phone, then mount usb in mounts and storage, then copy the Andromeda3 zip to the drive. You were almost there.
Fish around in the usb port with 301kOhms of resistance from radio shack. You will hit pins 4 abd 5 and you will be in download mode.
Click to expand...
Click to collapse
Thanks. I tried putting the Andromeda on the phone by copying it over to the phone through the mounted sd card but it was all of a sudden "write protected" and showed up as a cd instead of an sd card. :/ I know I was real close but I made some mistakes along the way
also, when you say fish around the usb port. you mean inside the phone? Is there any danger of hitting the wrong pins and possibly hurting my phone? (say i hit pins 3 and 5 by mistake or something) or is it all pretty safe? I was going to try and attempt the jig method that only used the resistors but n oticed the pins were horrible small in the phone:/
yakobo said:
Thanks. I tried putting the Andromeda on the phone by copying it over to the phone through the mounted sd card but it was all of a sudden "write protected" and showed up as a cd instead of an sd card. :/ I know I was real close but I made some mistakes along the way
also, when you say fish around the usb port. you mean inside the phone? Is there any danger of hitting the wrong pins and possibly hurting my phone? (say i hit pins 3 and 5 by mistake or something) or is it all pretty safe? I was going to try and attempt the jig method that only used the resistors but n oticed the pins were horrible small in the phone:/
Click to expand...
Click to collapse
It's not inside the phone... it's the USB port on the phone. One pin is on top and the other is on the bottom. If you don't have a JIG, that's the easy way to do it. There's no power on the USB port. This is a quick way to do it. You'll be fine. It's safe.
AdamOutler said:
It's not inside the phone... it's the USB port on the phone. One pin is on top and the other is on the bottom. If you don't have a JIG, that's the easy way to do it. There's no power on the USB port. This is a quick way to do it. You'll be fine. It's safe.
Click to expand...
Click to collapse
Sorry, that is what I meant. I meant to place where the charger is plugged in to. Just seems like the pins are really really tiny. Thank you for your help gonna get my resistors hopefully today and get my phone working again.

[Q] Semi Bricked?

I was trying to root/upgrade a captivate for a friend...
Had trouble, ended up restored to 2.1...rooted it and got into cwm, tried to load NYX ICS and phone would boot then black screen and I could hear the boot sounds...
Tried restore back to 2.1 and now I have the phone dots computer screen. I can get to download mode, but odin doesn't seem to want to work...
Any tips/tricks/ideas?
bigworm50 said:
I was trying to root/upgrade a captivate for a friend...
Had trouble, ended up restored to 2.1...rooted it and got into cwm, tried to load NYX ICS and phone would boot then black screen and I could hear the boot sounds...
Tried restore back to 2.1 and now I have the phone dots computer screen. I can get to download mode, but odin doesn't seem to want to work...
Any tips/tricks/ideas?
Click to expand...
Click to collapse
Sounds like to me you didn't have gingerbread bootloaders installed, instead had enclair bootloaders, you need to be on 2.3 gingerbread bootloaders to flash ICS. Try doing an odin one-click flash from here -> http://forum.xda-developers.com/showpost.php?p=18370912&postcount=3
Using the kk4 odin with bootloaders, I would remove the external sdcard and the sim card first, just to be sure.
But flashing bootloaders you can hard brick your phone and it will need to get jtagged.
Read the forums and understand what you are doing.
As always, I am not responsible if this messes up your phone.
Good luck
Thanks, downloading now...Yeah I figured out the bootloader part afterward...guess I needed to do more reading before I jumped in...
Odin recognizes the phone, but then seems to hang on DO NOT TURN OFF TARGET!!. It does setup connection, initialization, then set pit file first...so it seems to be working...I am going to leave it for a long while and see.
How long should it take?
crt60 said:
Try doing an odin one-click flash from here -> http://forum.xda-developers.com/showpost.php?p=18370912&postcount=3
Click to expand...
Click to collapse
So I tried a different usb port after reading some more and that kicked it in...so what do I need to do now to be able to load http://forum.xda-developers.com/showthread.php?t=1592141
sorry for the hand holding request, but I am out of my element with the captivate and gun shy after almost bricking it...
bigworm50 said:
so what do I need to do now to be able to load http://forum.xda-developers.com/showthread.php?t=1592141
Click to expand...
Click to collapse
Read the instruction in the op (original post) as to what to do. You will need to flash a kernel with clockwork mod.
Sent from my SAMSUNG-SGH-I897 using xda premium
I am confident following those directions. I was basically wondering if I was at the point of being able to follow them?
crt60 said:
Read the instruction in the op (original post) as to what to do. You will need to flash a kernel with clockwork mod.
Sent from my SAMSUNG-SGH-I897 using xda premium
Click to expand...
Click to collapse
bigworm50 said:
I am confident following those directions. I was basically wondering if I was at the point of being able to follow them?
Click to expand...
Click to collapse
Assuming you are running gingerbread with gingerbread bootloaders and you can get CWM, then yes.

[Q] Any way to get recovery mode to work? DL mode works, Recovery does not.

I have searched for the last 24 hours on this site for any mention of this problem and found nothing. I apologize if it has been covered elsewhere and would appreciate a link if I should be there instead of here. I am new to this forum.
I have an AT&T Captivate that I bought used for my wife. It was rooted and running some version of non-official Gingerbread when I got it (so it had been messed around with).
I have never been able to get into RECOVERY mode having tried every conceivable button and timing sequence at least 1 million times (3-button neutered?). I also have Android SDK installed on my PC and can send the "adb reboot recovery" command but it locks up at the AT&T screen and won't go any further so the PC is talking to the phone but the phone refuses to obey. Yes I have tried different USB ports and cables, un/reinstalling drivers, etc. The weird thing is that I can get into DL mode easily with the batt out, vol+/-,USB cable trick.
I originally took the phone all the way back to a stock Froyo ROM via Odin which appeared to work fine (but still no recovery mode) and then flashed to GB 2.3.5 with Kernel 2.6.35.7-I897UCKK4-CL614489 via "kh3_heimdall_cwm-One-Click_GB_2_3_5.jar"
Phone works OK now but I still can't get into RECOVERY mode. Unless I am mistaken, there are no ROMS available later than GB that can be flashed via Odin- all of the later ROMs need to be installed from recovery mode. The point of all this is that I want to try upgrading to ICS or JB but can't figure out how to do it without a way to get into recovery mode.
So the question is: How can I get recovery mode to work?
And: How can I update the ROM with no way to get into Recovery mode? Is it even possible?
Returning the phone is obviously out of the question as it is "obsolete" and I am not the original owner.
Thank you for any helpful insights.
captivated hippo said:
I have searched for the last 24 hours on this site for any mention of this problem and found nothing. I apologize if it has been covered elsewhere and would appreciate a link if I should be there instead of here. I am new to this forum.
I have an AT&T Captivate that I bought used for my wife. It was rooted and running some version of non-official Gingerbread when I got it (so it had been messed around with).
I have never been able to get into RECOVERY mode having tried every conceivable button and timing sequence at least 1 million times (3-button neutered?). I also have Android SDK installed on my PC and can send the "adb reboot recovery" command but it locks up at the AT&T screen and won't go any further so the PC is talking to the phone but the phone refuses to obey. Yes I have tried different USB ports and cables, un/reinstalling drivers, etc. The weird thing is that I can get into DL mode easily with the batt out, vol+/-,USB cable trick.
I originally took the phone all the way back to a stock Froyo ROM via Odin which appeared to work fine (but still no recovery mode) and then flashed to GB 2.3.5 with Kernel 2.6.35.7-I897UCKK4-CL614489 via "kh3_heimdall_cwm-One-Click_GB_2_3_5.jar"
Phone works OK now but I still can't get into RECOVERY mode. Unless I am mistaken, there are no ROMS available later than GB that can be flashed via Odin- all of the later ROMs need to be installed from recovery mode. The point of all this is that I want to try upgrading to ICS or JB but can't figure out how to do it without a way to get into recovery mode.
So the question is: How can I get recovery mode to work?
And: How can I update the ROM with no way to get into Recovery mode? Is it even possible?
Returning the phone is obviously out of the question as it is "obsolete" and I am not the original owner.
Thank you for any helpful insights.
Click to expand...
Click to collapse
Since you have no problems getting into download mode I suggest you start by going to this link... http://forum.xda-developers.com/showthread.php?t=1300843 Go to the third post and download the Odin one click of KK4 with bootloaders.
After you do the one-click back to stock go to this link... http://forum.xda-developers.com/showthread.php?t=1294477&highlight=corn+kernel and get the odin flashable version of 7.06 or 7.0A and if you don't already have Odin you'll of course need that too. Get yourself back into download mode and flash that kernel and it should give you back your recovery via the 3 button combo.
Worked! (eventually...sort of...)
m1batt1 said:
Since you have no problems getting into download mode I suggest you start by going to this link... http://forum.xda-developers.com/showthread.php?t=1300843 Go to the third post and download the Odin one click of KK4 with bootloaders.
After you do the one-click back to stock go to this link... http://forum.xda-developers.com/showthread.php?t=1294477&highlight=corn+kernel and get the odin flashable version of 7.06 or 7.0A and if you don't already have Odin you'll of course need that too. Get yourself back into download mode and flash that kernel and it should give you back your recovery via the 3 button combo.
Click to expand...
Click to collapse
m1batt1,
Thank you sooo much! It ALMOST worked!
- DL'ed Odin 1-click KK4 w/BL's as suggested, ran it, it failed and semi-bricked my phone... (phone--/!\---comp). Doh!
-Figured you were on the right track so DL'ed "I897UCKK4 Odin One Click - Stock, CONTAINS Bootloaders, Re-partition, Full Wipe" from 4-2ndtwin's post further down the same thread.
-after much anxiety and messing about to get it to connect, it successfully flashed!
-For the FIRST TIME EVER, I can get into recovery mode!
-followed up with corn kernel 7.06 as suggested with no problems
-now that the phone works as advertised, time for JB!
The funny thing is, I went back to stock ROMs several times and recovery never worked until now... go figure...
^
...then it had to be that KK4 one click in that 3rd post that fixed the prob.
Sent from my SGH-I897 using xda premium
I'm glad it got you back up and running! Now get your JB flash on! There are plenty to choose from for our "ancient" captivates.
One word of advice though. Coming from the point you're at now any JB ROM you flash will likely knock you into a boot loop on the first flashing attempt. Nothing is wrong just three button into recovery and flash again.
Sent from my SGH-I897 using xda app-developers app
And back up the efs folder, just in case.
It contains the vital IMEI info. :thumbup:
Sent from my SGH-I897 using xda premium
Thanks a million guys! Slim bean 2.9 up and running!
It Works!
Got to Slim Bean 2.9 through Cyanogen 9.1 and installed the Slim_GApps.
4-2ndtwin: Thanks for the suggestion to back up the efs folder. I hadn't done that before and now I am feeling VERY lucky that my phone still works at all! It lowered my stress level appreciably plus it was good practice using SDK.
m1batt1: Thanks for the heads up on the double flashing of JB ROM! It saved considerable unnecessary panic (although it was still somewhat unnerving)!
Consider both your thank you buttons righteously whacked! :good:

Categories

Resources