hi all,
i read on the thunderbolt section that a user was able to get an LTE thunderbolt on page plus service. Any1 looking willing to make the bionic work?
I intend to try what was done to the thunderbolt, just scared it will brick the phone.
-mike
What is page plus?
beehiveblack said:
What is page plus?
Click to expand...
Click to collapse
+ 1 lol
Sent from my DROID BIONIC using Tapatalk
http://www.pagepluscellular.com/
Page Plus Cellular is a prepaid mobile carrier runnign VZW towers...
It's not possible
Sent from my DROID BIONIC using xda premium
if thunderbolt was done, why couldn't Bionic?
Kernel i assume.
Why not use the droid x 2 than it is duel core and since LTE is not in the mix why not get a thinner phone. Droid x would be preface.
Newbie guide to programming droid bionic with 3g data on pageplus
1.get a 4glte sim card.
2. factory data reset phone
3. Activate phone by using the first 15 characters of the imei (drop 1 character from the end)
4. Push pageplus prl to phone. (I do not know how to link download files to this forum yet)
I used cdma workshop 3.8 demo version
A.put phone in diagnostic mode power off, hold up and down buttons and power back on, select bp tools at the bottom by button down to it and button up to select bp tools
B. Connect phone to computer open up cdma workshop go to ports and select the one that says diag it should be the one at the bottom.
C. Click connect to connect phone
D. Go to main tab click spc send 000000 to unlock phone, go to other tab to load pageplus prl to phone, select write and find your prl file and it should write it to the phone.
5. Insert sim card.
6. Restart phone. Phone should OTA program.
7. dial *#*#4636#*#* go to phone information go to cdma auto prl and change it to cdma only
Back out of that
8. dial ##program go to test mode next over to evrc hdr hybrid mode change network type to cdma and back out phone will restart
(check menu/settings/phone status make sure mobile network type says CDMA 1xrtt and you have 1x data)
9. dial *#*#4636#*#* go to phone information go to cdma and change it to cdma auto prl
Back out of that
10. Power down and remove sim card and power up.
11. dial ##program go to test mode next over to evrc hdr hybrid mode change network type to cdma and evdo phone will restart
(check menu/settings/phone status make sure mobile network type says CDMA EvDo rev A. if it says eHRPD redo steps 10-14.)
12. dial *#*#4636#*#* go to phone information go to cdma auto prl and change it to unknown
Back out of that
(check menu/settings/phone status make sure mobile network type says CDMA EvDo rev A. if it says eHRPD redo steps 10-15.)
13. Power down phone, replace sim card power up you should have 3g and talk and text
this is the pageplus prl that i used
http://www.4shared.com/file/qryS5x4T/51720_EVDO.html
Did you really get the Droid Bionic to function correctly on Page plus? Reason I ask is cause I just ordered a Bionic to root and get it working on page plus, really hope this works. Can I use the demo verison of cdma workshop to flash my phone?
thanks.
Mike,
---------- Post added at 08:47 AM ---------- Previous post was at 08:41 AM ----------
Also, Would be nice to see a video of it working or how you went about flashing it.
Thanks.
Mike,
phullofphil said:
Why not use the droid x 2 than it is duel core and since LTE is not in the mix why not get a thinner phone. Droid x would be preface.
Click to expand...
Click to collapse
Some people don't like thin phones.
Sent from my DROID BIONIC using XDA App
I was thinking about getting the droid x2 being I know people got it working with page plus, but I just wanted a newer model, was going to get the razr in fact, but didn't cause I never seen any write ups on people getting it working with page plus, Sure it can be done, these guys here are amazing and have help me through the years, rooting my old school droid and installing ubuntu on it.
Would love to see proof of the droid bionic working on page plus, sure it can be done, same with the razr, where there is a will there is away for sure, Phone will be here tomorrow and will try myself in fact.
Thanks.
Mike,
Your probably better off trying the Droid x2 as it's a 3g phone. Even if you do get the bionic or razr working on pageplus, you probably won't get data as they are lte phones which use a different technology than what pageplus uses.
Sent from my DROID BIONIC using XDA App
I got this to work on a bionic. great phone!!
I will make a video of this when i get time. Use cdma workshop to put a pageplus prl on the phone. It will activate normally if you drop the last character from the IMEI. After that *#*#4636#*#* to turn radio off and change cdma/gsm/auto prl to cdma only to get solid 1x data. The method i use to get 3g works until the phone drops signal. Then you have to repeat the method. It can get agrivating. But i am sending this post on my 3g from droid bionic on Pageplus.
Could someone please help me get my Droid bionic to work on pageplus
Is it possible to flash the bionic over to Revol (similar to cricket if you don't know)
Sent from my DROID BIONIC using XDA App
it is no problem to get the bionic on pageplus, cdma workshop demo will work just fine. you also need a 4glte sim card. factory data reset the phone and you need to install cdma workshop demo first. download a pageplus prl. you can find one at http://www.4shared.com/file/qryS5x4T/51720_EVDO.html
download motorola usb drivers from motorola website
http://www.motorola.com/staticfiles/...iver_5.4.0.exe
and install them.
power off your computer.
you power down your phone and put it in diagnostic mode by holding down both volume up and down buttons and pressing power on button at the top.
use the down button to toggle down to bp tools at the bottom and press the volume up button to select it. your phone will power on in diagnostic mode.
connect your phone via a usb cable to your computer and power on your computer. after your computer is powered up wait for the computer to install the device drivers for your phone
open up device manager and find the modems and look for your phone (moto something or other or or xt875) and see which com port it is on by looking in the advanced tab or one of the other tabs. open up cdma workshop and select the com port your bionic is on and click on the connect button. click read to make sure your phone is connected and go to the security tab and SPC /User lock click send and send spc 000000 to your phone to unlock it so that you can write to it. go to the main tab and at the bottom you will see a drop down menu that says cdma click the drop down arrow and click on cdma-2. go to the r-uim configuration and click on nv only go to the bottom and click write click on the nam-1 and click nam-2 and click write again. now go to the cdma-2 tab and click cdma and go up to the tabs and click other go to the prl and click write and find the location you downloaded the prl file and select it and the program will write it to the phone. now you can power off the phone. activate the imei number by dropping off the last digit to make the number one less (14 instead of 15), power it up normally and the phone will program normally with the 4glte sim card installed. after activation, to get 1x data with mms go to the dial pad and *#*#4636#*#* go down to the turn off radio button and click it. it should now say turn on radio go to the gsm\cdma\prl auto drop down menu and select cdma only and then click turn on radio button back button out of there and you now have 1x data with talk, text and mms. painless
---------- Post added at 10:02 PM ---------- Previous post was at 09:53 PM ----------
[/COLOR]i am sure this method will work for other mvno's as well. you would need to put a compatible prl on the phone.
adam3rd said:
I will make a video of this when i get time. Use cdma workshop to put a pageplus prl on the phone. It will activate normally if you drop the last character from the IMEI. After that *#*#4636#*#* to turn radio off and change cdma/gsm/auto prl to cdma only to get solid 1x data. The method i use to get 3g works until the phone drops signal. Then you have to repeat the method. It can get agrivating. But i am sending this post on my 3g from droid bionic on Pageplus.
Click to expand...
Click to collapse
what exactly does this mean? how do you activate minus 1 character from the IMEI? When you turn the phone on doesn't it just try to activate by itself? Or do you do something to the IMEI to make it work through the cdma workshop?
the imei number is 1 character less than an esn number. the last number in the imei number is not used to program the phone. if you attempt to program a imei number on page plus with the last number it will not program. a 4g lte phone will automatically program with a sim card in it if you have the correct prl file for your carrier that the imei number is programmed for. a 4g lte prl is not compatible with pageplus, thus you will need to push or write a compatible prl file to the phone for it to program to pageplus. (esn or imei mobile identification number is the number you give the carrier ...pagplus...verizon...sprint...etc... so they know where to send your cellular signal to)
Hello Everyone,
I've been tempted to purchase a Droid 4 but I'm currently on the Page plus Network. I've seen many tutorials for flashing 4G LTE phones on to page plus but I didn't really see a tutorial for the Droid 4. I was wondering since the D4 is similar to the RAZR/BIONIC, if I can just follow those tutorials. I really want to use the D4 and would appreciate it if someone were to help guide me through the flashing process.
Thanks A lot,
jeanr464.
jeanr464 said:
Hello Everyone,
I've been tempted to purchase a Droid 4 but I'm currently on the Page plus Network. I've seen many tutorials for flashing 4G LTE phones on to page plus but I didn't really see a tutorial for the Droid 4. I was wondering since the D4 is similar to the RAZR/BIONIC, if I can just follow those tutorials. I really want to use the D4 and would appreciate it if someone were to help guide me through the flashing process.
Thanks A lot,
jeanr464.
Click to expand...
Click to collapse
Razr xt912 has even same hardware, it shouldn't be a problem to use tutorial for razr and doing same thing on d4
Sent from my XT894 using xda premium
Droid 4 on ICS different Method. Data Challenge.
olegfusion said:
Razr xt912 has even same hardware, it shouldn't be a problem to use tutorial for razr and doing same thing on d4
Sent from my XT894 using xda premium
Click to expand...
Click to collapse
So I received my droid 4 and unfortunatly it was shipped with ICS. So following a lot of the common RAZR/BIONIC tutorials didn't really work out well for me. I saw a lot of people also having trouble trying to get the Droid 4 to work properly on PP with ICS. So I just wanted to say I followed the following steps on this following tutorial and it worked our flawlessly and I was able to get my phone working on talk/text 1X data.
howardforums. com/showthread. php/ 1774610-Droid-BIONIC-ICS-manual-activation-talk-text-mms-3g-all-working
Now my only challenge is getting 3G Data. For every razr/bionic tutorial I saw they went to the Phone info (*#*#4636#*#*) to try to set the radio test settings to get 3G/EVDO. For some reason on my Droid 4 when I enter this it simply disappears on the dialer and nothing happens. Does anyone know how to get 3G working on the Droid 4. So far all I did was disable all the LTE APNs, Enviroment, lte bbpanic disable, and change the sim type to 3g test uicc.
Can anyone help me out with this?
Solution to 3G on D4 ICS running on Pageplus.
jeanr464 said:
So I received my droid 4 and unfortunatly it was shipped with ICS. So following a lot of the common RAZR/BIONIC tutorials didn't really work out well for me. I saw a lot of people also having trouble trying to get the Droid 4 to work properly on PP with ICS. So I just wanted to say I followed the following steps on this following tutorial and it worked our flawlessly and I was able to get my phone working on talk/text 1X data.
howardforums. com/showthread. php/ 1774610-Droid-BIONIC-ICS-manual-activation-talk-text-mms-3g-all-working
Now my only challenge is getting 3G Data. For every razr/bionic tutorial I saw they went to the Phone info (*#*#4636#*#*) to try to set the radio test settings to get 3G/EVDO. For some reason on my Droid 4 when I enter this it simply disappears on the dialer and nothing happens. Does anyone know how to get 3G working on the Droid 4. So far all I did was disable all the LTE APNs, Enviroment, lte bbpanic disable, and change the sim type to 3g test uicc.
Can anyone help me out with this?
Click to expand...
Click to collapse
OKAY! After hours of playing with my Droid 4 on ICS on the Page Plus Network, I finally got 3G to work!!!!
First off, I realized the *#*#4636#*#* aka the INFO code wasn't working on the Droid 4 model because it doesn't exist in the firmware. Instead going through the program menu (##PROGRAM) I was able to access the test mode there and change options.
From my D4 ICS experience, to get 3G instead of 1X I had to
1. Access the Program Menu from the dialer ##PROGRAM aka ##7764726
2. Enter the SPC (000000)
3.Scroll Down to LTE TEST SETTINGS
4. Click SIM TYPE and then Choose 3G Test UICC then click Apply
5. Scroll down to LTE bppanic and select disable then click Apply
6.Then Scroll down and Click (Disable Class 1 APN, Disable Class 2 APN, Disable Class 3 APN)
7. Then choose LTE Movement detection and select Disable.
8. Click back twice the phone will restart.
At This point according to tutorials you should have 3G but if you're like me and unlucky didn't have 3G then do this.
1. Go to the dialer
2. Enter ##PROGRAM aka ##7764726
3. Then enter SPC (000000)
4. Then click Test Mode
5. Click Next and then click next again then you should be on the field test Screen
6. HDR hybrid mode should be (ON)
7.EVDO revision should be (A)
8. CDMA RX Diversity should be (OFF)
9. HDR RX Diversity should be (OFF)
10. Finally look up to where it says Network Mode
11. Change it to EVDO only and Check the top where your signal bars on. Give it a minute, it should pop and say 3G. If it says 3G and you can proceed to the final step and change the network selection to CDMA and EVDO and then back out of the menu.
12. There you go! You should have 3G on the Droid 4 now in ICS running on Pageplus.
In Gingerbread it was a whole lot more simpler. I hope this solution will help people running ICS.
Forgot to mention.
jeanr464 said:
OKAY! After hours of playing with my Droid 4 on ICS on the Page Plus Network, I finally got 3G to work!!!!
First off, I realized the *#*#4636#*#* aka the INFO code wasn't working on the Droid 4 model because it doesn't exist in the firmware. Instead going through the program menu (##PROGRAM) I was able to access the test mode there and change options.
From my D4 ICS experience, to get 3G instead of 1X I had to
1. Access the Program Menu from the dialer ##PROGRAM aka ##7764726
2. Enter the SPC (000000)
3.Scroll Down to LTE TEST SETTINGS
4. Click SIM TYPE and then Choose 3G Test UICC then click Apply
5. Scroll down to LTE bppanic and select disable then click Apply
6.Then Scroll down and Click (Disable Class 1 APN, Disable Class 2 APN, Disable Class 3 APN)
7. Then choose LTE Movement detection and select Disable.
8. Click back twice the phone will restart.
At This point according to tutorials you should have 3G but if you're like me and unlucky didn't have 3G then do this.
1. Go to the dialer
2. Enter ##PROGRAM aka ##7764726
3. Then enter SPC (000000)
4. Then click Test Mode
5. Click Next and then click next again then you should be on the field test Screen
6. HDR hybrid mode should be (ON)
7.EVDO revision should be (A)
8. CDMA RX Diversity should be (OFF)
9. HDR RX Diversity should be (OFF)
10. Finally look up to where it says Network Mode
11. Change it to EVDO only and Check the top where your signal bars on. Give it a minute, it should pop and say 3G. If it says 3G and you can proceed to the final step and change the network selection to CDMA and EVDO and then back out of the menu.
12. There you go! You should have 3G on the Droid 4 now in ICS running on Pageplus.
In Gingerbread it was a whole lot more simpler. I hope this solution will help people running ICS.
Click to expand...
Click to collapse
By the way. My 4G lte sim card was in my phone the whole time. I don't know if it makes a difference but from the moment I got the the D4 and started flashing I left my D4 LTE sim inside my phone.
jeanr464 said:
OKAY! After hours of playing with my Droid 4 on ICS on the Page Plus Network, I finally got 3G to work!!!!
Click to expand...
Click to collapse
Hi Jeanr464. Does the 3G survive a reboot? The link to the howard forums tutorial in post #3 seems to indicate you need to;
snoop1979 said:
If your phone gets restarted or turned off. you phone will say needs to be activated again, however you will have talk and text enabled. to regain mms and 3g repeat steps 16-24.
Click to expand...
Click to collapse
devinpatterson said:
Hi Jeanr464. Does the 3G survive a reboot? The link to the howard forums tutorial in post #3 seems to indicate you need to;
Click to expand...
Click to collapse
Hey devinpatterson!
I can't tell you how many times I rebooted my phone or my phone died and has to turn on. The 3G does stick after reboot and the activatiion doesn't come back. I guess once the phone is succesfully activated the screen doesn't come back. Once you configure your phone settings to get 3G just leave those settings alone. I can confirm on. The droid 4 that it sticks after reboot.
Although, I can tell you if you remove the sim then the phone acts crazy with activation and all that jazz. While I was experimenting for hours getting 3G on the phone I saw some places that you have to remove the sim. So I did. And then activation and emergency calls and everything popped back on,until I put the sim back and reboot the phone.
According to all the tutorials I saw and my experience as long as you use a blank lte sim and successfully activate the phone (manually/*228 etc) the phone sim is programmed to work with your phone and removing or putting another sim with cause activation and data settings to trigger again.
Hope this explaination helps! Best of luck,
jeanr464
jeanr464 said:
According to all the tutorials I saw and my experience as long as you use a blank lte sim and successfully activate the phone (manually/*228 etc) the phone sim is programmed to work with your phone and removing or putting another sim with cause activation and data settings to trigger again.
Click to expand...
Click to collapse
Hi jeanr464. Thank you for all of this brilliant info about the Droid 4 with ICS. I'm a newbie also wanting to set up my new Droid 4 with PagePlus and wondering, does Snoop's step of dialing *22800 for activation work on this phone? If not, is manual activation something different, and if so, how do you manually activate? And in general, do all of Snoop's steps work except for dialing *#*#4636#*#* work for this phone?
Thanks in advance,
tubaman101
Manual vs *228
tubaman101 said:
Hi jeanr464. Thank you for all of this brilliant info about the Droid 4 with ICS. I'm a newbie also wanting to set up my new Droid 4 with PagePlus and wondering, does Snoop's step of dialing *22800 for activation work on this phone? If not, is manual activation something different, and if so, how do you manually activate? And in general, do all of Snoop's steps work except for dialing *#*#4636#*#* work for this phone?
Thanks in advance,
tubaman101
Click to expand...
Click to collapse
Hey tubaman101,
To answer your question, manual activation is basically manually programming the phone and doing all the steps that *228 would have done. From my droid 4 experience getting on to pageplus, *228 didn't work right off the bat because of sim restrictions or some type of error. What you have to do is manually program the phone first with the correct settings to make basic features works then you'll be able to dial *228 where it will correct everything and fix everything to work like data and roaming etc. According to Snoops tutorial, basically what the manual programming is is the step where he enters ##7764726 aka ##PROGRAM and fixes the min and the mdn and settings the cdma only option. From there you have manually programed the phone. Then after setting those options when you try *228 it should work and then *228 will correct and program automatically all the phone options which then you should have perfect talk text and 1x. To get 3G just follow my steps above on how I did it.
To make it all simple(I'm going to summarize snoop' method) once you get the D4 and a blank sim, insert sim, enter bptools (tutorial shows how), set the phone to nvonly and evdo rev a with cdma workshop, dfs tool or qpst (tutorial shows how to) then from there enter ##PROGRAM in the dialer manually program your phone min and mdn (if you don't know what it is you can request PP customer service or PM me to help you get it, and set your phone to cdma only mode (tutorial explains how) and afterwards *228 and your set.
After to get 3G follow my steps.
It was very troublesome for me at first because I had no clue how to do this but I've done 4 droid 4s and a razr with this method so far so I've became slight savvy with it. If you have ANY trouble just list it here or PM me and I'll be more than happy to help out.
Good luck,
jeanr464
jeanr464 said:
once you get the D4 and a blank sim, insert sim, enter bptools (tutorial shows how), set the phone to nvonly and evdo rev a with cdma workshop, dfs tool or qpst
Click to expand...
Click to collapse
Hi jeanr464. I sent you a PM about if it is necessary to load a PagePlus prl file during the process, but I have a couple more questions.
I started with the steps you outlined using DFS. I don't think the nvonly and evdo rev a settings stuck because I got some sort of error message in the DFS Tools log, and I was not able to complete the next step of dialing ##program.
I'm wondering if it is because my sim isn't blank. I bought my Droid 4 on eBay new. (It was actually a warranty replacement phone that had never been opened or used.) It came with a new Verizon 4G sim card on top of the box. I wonder if this card was "assigned" to the previous owner, and so perhaps isn't blank.
Do you think I need to buy a new "blank" sim card? …and if so, do you have any recommendations as to where to get one?
Also, I was wondering if the port I chose in the CDMA tools was the right one. I chose "COM 6" in the attached picture. Was that correct?
(In case it matters, I'm doing this in Windows 7 on a partition created on my Mac computer.)
Thanks again!
tubaman101
The Hopeful solution.
tubaman101 said:
Hi jeanr464. I sent you a PM about if it is necessary to load a PagePlus prl file during the process, but I have a couple more questions.
I started with the steps you outlined using DFS. I don't think the nvonly and evdo rev a settings stuck because I got some sort of error message in the DFS Tools log, and I was not able to complete the next step of dialing ##program.
I'm wondering if it is because my sim isn't blank. I bought my Droid 4 on eBay new. (It was actually a warranty replacement phone that had never been opened or used.) It came with a new Verizon 4G sim card on top of the box. I wonder if this card was "assigned" to the previous owner, and so perhaps isn't blank.
Do you think I need to buy a new "blank" sim card? …and if so, do you have any recommendations as to where to get one?
Also, I was wondering if the port I chose in the CDMA tools was the right one. I chose "COM 6" in the attached picture. Was that correct?
(In case it matters, I'm doing this in Windows 7 on a partition created on my Mac computer.)
Thanks again!
tubaman101
Click to expand...
Click to collapse
Okay, I don't think the sim card would be that much of a problem, but if the problem persists after trying the next steps then you can get a new one off ebay for 5 dollars like I did. In any case, you did choose the correct port in DFS tools. You brought up a very good point that I forgot to mention. You do need to load a pageplus prl. The one I used during the process was the 51720 EVDO prl. Once you find that one "google will be a great help", open up DFS tools and then make sure after you load up the program and select the port you enter the SPC 000000, its on the top right corner of DFS I believe ( I used Cdma ws). After that overwrite the PRL using the program and then make sure you set nvonly on nam 1 and nam 2 and set evda a. If you keep on getting errors with DFS tool let me know. In this case we might have to figure something else. In any case if you are successful, then once you trestart the phone you should if you hadn't already, bypass the activation or welcome screen, if you don't know how to do that let me know but if you are already on the regular screen with the apps and everything then proceed to the dialer and press ##program and follow the rest of snoops guide and you should be fine.
Honestly, the hardest part of this whole process is the programming on PC. After that you should be fine. As far as windows 7 is concerned, I used windows 7 and I was fine.
Enter the Phone in BPtools
Connect to PC
Go to system settings and make sure you got the diag port com #
Open DFS
Select the com # and read
Send SPC 000000
Load PRL 51720EVDO
Write it to the phone
Change nam 1 and nam 2 to NVONLY instead of RUIM
change data to EVDO REV A.
make sure all settings are written and restart phone
If you are at the welcome screen bypass it (four corners unlock) if the phone is at the regular menu with the apps then go straight to dailer and ##PROGRAM
Change MDN and MIN
enter test mode and click next until you see the options to change the phone network to CDMA only
click back twice and the phone should restart
at this point you should have somewhat some type of service but then press *228
It might reject it the first time but try again and the activation screen will come up and the music will play and activate your phone
After that look above to figure out 3G
If you still have trouble PM me and we'll see what we can do.
Forgot mention
jeanr464 said:
Okay, I don't think the sim card would be that much of a problem, but if the problem persists after trying the next steps then you can get a new one off ebay for 5 dollars like I did. In any case, you did choose the correct port in DFS tools. You brought up a very good point that I forgot to mention. You do need to load a pageplus prl. The one I used during the process was the 51720 EVDO prl. Once you find that one "google will be a great help", open up DFS tools and then make sure after you load up the program and select the port you enter the SPC 000000, its on the top right corner of DFS I believe ( I used Cdma ws). After that overwrite the PRL using the program and then make sure you set nvonly on nam 1 and nam 2 and set evda a. If you keep on getting errors with DFS tool let me know. In this case we might have to figure something else. In any case if you are successful, then once you trestart the phone you should if you hadn't already, bypass the activation or welcome screen, if you don't know how to do that let me know but if you are already on the regular screen with the apps and everything then proceed to the dialer and press ##program and follow the rest of snoops guide and you should be fine.
Honestly, the hardest part of this whole process is the programming on PC. After that you should be fine. As far as windows 7 is concerned, I used windows 7 and I was fine.
Enter the Phone in BPtools
Connect to PC
Go to system settings and make sure you got the diag port com #
Open DFS
Select the com # and read
Send SPC 000000
Load PRL 51720EVDO
Write it to the phone
Change nam 1 and nam 2 to NVONLY instead of RUIM
change data to EVDO REV A.
make sure all settings are written and restart phone
If you are at the welcome screen bypass it (four corners unlock) if the phone is at the regular menu with the apps then go straight to dailer and ##PROGRAM
Change MDN and MIN
enter test mode and click next until you see the options to change the phone network to CDMA only
click back twice and the phone should restart
at this point you should have somewhat some type of service but then press *228
It might reject it the first time but try again and the activation screen will come up and the music will play and activate your phone
After that look above to figure out 3G
If you still have trouble PM me and we'll see what we can do.
Click to expand...
Click to collapse
Forgot to mention one thing, after you program the phone on DFS tool you should switch the esn from PP from your other phone. Your MEID is the IMEI without the last digit so you should have 14 characters in total. Once you switch the esn or set a new activation from PP then proceed to the step with the ##program etc.
Droid 4
jeanr464 said:
Hey tubaman101,
To answer your question, manual activation is basically manually programming the phone and doing all the steps that *228 would have done. From my droid 4 experience getting on to pageplus, *228 didn't work right off the bat because of sim restrictions or some type of error. What you have to do is manually program the phone first with the correct settings to make basic features works then you'll be able to dial *228 where it will correct everything and fix everything to work like data and roaming etc. According to Snoops tutorial, basically what the manual programming is is the step where he enters ##7764726 aka ##PROGRAM and fixes the min and the mdn and settings the cdma only option. From there you have manually programed the phone. Then after setting those options when you try *228 it should work and then *228 will correct and program automatically all the phone options which then you should have perfect talk text and 1x. To get 3G just follow my steps above on how I did it.
To make it all simple(I'm going to summarize snoop' method) once you get the D4 and a blank sim, insert sim, enter bptools (tutorial shows how), set the phone to nvonly and evdo rev a with cdma workshop, dfs tool or qpst (tutorial shows how to) then from there enter ##PROGRAM in the dialer manually program your phone min and mdn (if you don't know what it is you can request PP customer service or PM me to help you get it, and set your phone to cdma only mode (tutorial explains how) and afterwards *228 and your set.
After to get 3G follow my steps.
It was very troublesome for me at first because I had no clue how to do this but I've done 4 droid 4s and a razr with this method so far so I've became slight savvy with it. If you have ANY trouble just list it here or PM me and I'll be more than happy to help out.
Good luck,
jeanr464
Click to expand...
Click to collapse
Jean I think I followed all the instructions on here but it still says fail to connect NAM after I put in the MIN and MDN so I can never I finish programing my droid 4 to Page plus. Can you please help me.
Warning Droid 4 JellyBean Upgrade + Pageplus Users
Just a fair warning to everyone using Pageplus. As you all the Jellybean update has been released and your phone might've already offered to upgrade your OS.
DO NOT UPDATE!!!!! I REPEAT DO NOT UPDATE!!!!
Although JellyBean is very beautiful, this update will break your Page plus configuration. I had two friends already who were on Droid Razr/Maxx and updated to JellyBean. The whole CDMA WS config has been reset so options like NV_ONLY and evdo config has been erased leaving the phone in a non working state- In terms of calling, texting or data.
I'm very tempted to get JellyBean and everyone is looking for a safe solution to upgrade to JellyBean and have PP. As far as I've seen online, there have been successful tutorials but it required re-flashing the system to a factory state and re-configuring and other had it where you need a new sim and was necessary to root the phone. I'll be experimenting and posting my results soon. If anyone comes up with a success, please share!!!:laugh:
Good Luck and be pre-cautious!,
jeanr464
Working Perfect
I have my Droid 4 JB flashed working with full 3G on Pageplus never activated SIM and no problems. Same way as with the RAZR/RAZR MAXX. You can use any sim and not have any problems.
What was your situation?
How did you do it? I performed a straight upgrade and my config screwed up. Did you just reflash it and reconfigured it? Can I apply the same CDMA workshop method to this firmware?
lionsro said:
I have my Droid 4 JB flashed working with full 3G on Pageplus never activated SIM and no problems. Same way as with the RAZR/RAZR MAXX. You can use any sim and not have any problems.
Click to expand...
Click to collapse
Getting 3G to stick
Hey. Thanks for the tutorial on how to get 3G working. I haven't gotten it to work for some reason. I'm running ICS and I have 1X working. My girlfriend has the same phone and I did the same thing, but for whatever reason, not even 1X will work on hers. I did your settings in the ##program menu. The LTE and test settings. I'm not having luck getting 3G to stick.
It also seems that I cannot always get data to work by toggling wifi off. I have to not be around it or turn off my router. Getting 1X to work seems to sometimes be random. If I get 1x working and then If I go into the ##program menu now and turn EDVO only, 3G will come up for about 5 seconds and then disappear. After many restarts and trying things, 1X is all I can get. I wonder if it has something to do with where I am? Great Falls, Montana.
Any ideas would be appreciated.
Try this.
drossvirex said:
Hey. Thanks for the tutorial on how to get 3G working. I haven't gotten it to work for some reason. I'm running ICS and I have 1X working. My girlfriend has the same phone and I did the same thing, but for whatever reason, not even 1X will work on hers. I did your settings in the ##program menu. The LTE and test settings. I'm not having luck getting 3G to stick.
It also seems that I cannot always get data to work by toggling wifi off. I have to not be around it or turn off my router. Getting 1X to work seems to sometimes be random. If I get 1x working and then If I go into the ##program menu now and turn EDVO only, 3G will come up for about 5 seconds and then disappear. After many restarts and trying things, 1X is all I can get. I wonder if it has something to do with where I am? Great Falls, Montana.
Any ideas would be appreciated.
Click to expand...
Click to collapse
Okay, I'm actually stumped about your situation.. Seems very awkward. In any case let's see what we can do. "Hopefully your on ICS and not JellyBean"
I'm going to post my phone settings and try to match her settings to mine. You said you already did the LTE bbpanic off , apns disable, and test settings...
Okay Go to test settings in the program menu, click next until you see the Field test screen and make sure your phone matches these settings:
Service Option - EVRC
HDR Hybrid Mode - ON
EVDO Revision- A
Network Mode- CDMA and EVDO
CDMA RX Diversity- OFF
HDR RX Diversity- OFF
then hit the back button on your phone twice so it can restart.
If 3G still doesn't work then we need to CDMA WS your phone. It would seem the there is something wrong with the EVDO settings. To me it sounds like the EVDO protocol might be wrong.
jeanr464 said:
Okay, I'm actually stumped about your situation.. Seems very awkward. In any case let's see what we can do. "Hopefully your on ICS and not JellyBean"
I'm going to post my phone settings and try to match her settings to mine. You said you already did the LTE bbpanic off , apns disable, and test settings...
Okay Go to test settings in the program menu, click next until you see the Field test screen and make sure your phone matches these settings:
Service Option - EVRC
HDR Hybrid Mode - ON
EVDO Revision- A
Network Mode- CDMA and EVDO
CDMA RX Diversity- OFF
HDR RX Diversity- OFF
then hit the back button on your phone twice so it can restart.
If 3G still doesn't work then we need to CDMA WS your phone. It would seem the there is something wrong with the EVDO settings. To me it sounds like the EVDO protocol might be wrong.
Click to expand...
Click to collapse
I can confirm I am not on Jellybean. I didn't update it yet because I thought it might break it. Also all of those settings match on both of our phones.
Lets Go Through Your Settings
drossvirex said:
I can confirm I am not on Jellybean. I didn't update it yet because I thought it might break it. Also all of those settings match on both of our phones.
Click to expand...
Click to collapse
Okay. So... I think it might have to be with the configuration of the phone. I believe it could be:
1. The PRL
or
2. EVDO settings
So we're going to have to CDMA WS or DFS your phone and check the settings. (Recommend DFS since everything is available.)
www.cdma-ware.com or http://www.cdmatool.com/
Put your phone in Bptools mode - (Turn off, press volume +/- buttons and press power, scroll to bptools, press volume up)
Connect it to the computer
Go to device manager and find out what COM port it's on.
Open DFS and select the ports on the top left, double click on the port of your phone (A green circle should appear next to it after your click) then exit out of the port selection screen.
Then on the top left of the screen under Ports you should see SPC. Click on it to unlock the SPC of your phone.
Now click on the Programming tab. Once you click the Programming Tab, Click on the NAM tab under ( It's between general and Data).
Now there should be a section to the right that says PRL. on the bottom click READ and then tell me what PRL number shows up. (The number is located in the box on top of the Read button).
Afterwards, click on the Data tab ( It's next to the NAM tab you clicked earlier)
On the bottom there should be a READ button. Click that button.
Now Tell me in your next post if the PPP config to the left has your phone number @dun.vzw3g.com and post all your the MODE settings
Ex:
SIP NAI= (Your Phone) @dun.vzw3g.com
UID=(Your Phone)@vzw3g.com
MODE:
HDR SCP force AT config: =
HDR SCP force release 0 config=
Hybrid preferred mode:
Data MDR (HSPD) mode:
Data service option:
I'll Post screenshots of my phone config so you can compare. Before you change anything POST what your phone settings display.
Hope we can solve this,
jeanr464
Hey guys, which mode should I be on, CM10.1, the only time 4G will work is when set on RUIM/SIM which I expected, but the other option is NV. When on NV only 3g connects but all else is fine.
Should I give Sprint a ring?
**Just to clarify, I am a bit confused as the One has a SIM card, and most other sprint phones use NV.
DTgreat said:
Hey guys, which mode should I be on, CM10.1, the only time 4G will work is when set on RUIM/SIM which I expected, but the other option is NV. When on NV only 3g connects but all else is fine.
Should I give Sprint a ring?
**Just to clarify, I am a bit confused as the One has a SIM card, and most other sprint phones use NV.
Click to expand...
Click to collapse
SIM controls 4G LTE. NV controls 3G. Calling sprint would be useless. When you tell them on CM10.1 they will tell you they can not help. If you lie then their support documents wont match up and the info the give you will be useless.
Kraizk said:
SIM controls 4G LTE. NV controls 3G. Calling sprint would be useless. When you tell them on CM10.1 they will tell you they can not help. If you lie then their support documents wont match up and the info the give you will be useless.
Click to expand...
Click to collapse
I am pretty sure this is due to a mismatch of my MEID and my IMEI. They are going to try to reset it, with manual programming....
(Update 1)Flashed back to stock, waiting on manual programming...
*Update 2*
Asked me to enter all 0's for my MSID while programming device....
OK so I went and Had a guy (page plus Dealer) switch my BIONIC over to Pageplus...I can make phone calls no problem.
BUT NO 3G or MMS.
running android 4.1.2
sys version 98.72.22.xt875
build number 9.8.8o-72_vzw-22
I don't think its rooted.
the guy did something where I dont need a sim.
I have scanned the pages but cant seem to find any help with the recent update.
I am not half as smart as some of you all so if you can give me step by step directions on how to fix this I would greatly appreciate it.
still no answer or help? WOW
How are you supposed to make phone calls without a sim? I'd take it back to Pageplus and have them fix the issue. Your build number looks funny, even though you are not on the latest ota update. Are you on a custom rom? That could be the problem.
cucci_slamr said:
OK so I went and Had a guy (page plus Dealer) switch my BIONIC over to Pageplus...I can make phone calls no problem.
BUT NO 3G or MMS.
running android 4.1.2
sys version 98.72.22.xt875
build number 9.8.8o-72_vzw-22
I don't think its rooted.
the guy did something where I dont need a sim.
I have scanned the pages but cant seem to find any help with the recent update.
I am not half as smart as some of you all so if you can give me step by step directions on how to fix this I would greatly appreciate it.
Click to expand...
Click to collapse
You need Verizon 4G LTE sim to make data work like we did on ICS..
Please insert any blank Verizon 4G LTE sim and your data will start automatically....
matriX1218 said:
You need Verizon 4G LTE sim to make data work like we did on ICS..
Please insert any blank Verizon 4G LTE sim and your data will start automatically....
Click to expand...
Click to collapse
ok so I got the sim but where do I find instructions on how to get the data (3g) and MMS working?
I have no clue as to how the phone works without a sim either. All I know Is that I can make calls and send texts without a sim card.
OK with the verizon sim in I get a solid 1X but no MMS or 3G...I have tried the other pages advice and instructions but am sooooo lost.
PLEASE HELP
cucci_slamr said:
OK with the verizon sim in I get a solid 1X but no MMS or 3G...I have tried the other pages advice and instructions but am sooooo lost.
PLEASE HELP
Click to expand...
Click to collapse
Glad 1x is working...
Now press *#*#4636#*#* on dial
Select Phone Information
Scroll down to bottom and change network type to CDMA auto prl...
Wait for few seconds...
Press back and go to home...
Reboot...
Voila 3G will start :thumbup:
sent from my DROID BIONIC via Reliance Wireless
matriX1218 said:
Glad 1x is working...
Now press *#*#4636#*#* on dial
Select Phone Information
Scroll down to bottom and change network type to CDMA auto prl...
Wait for few seconds...
Press back and go to home...
Reboot...
Voila 3G will start :thumbup:
sent from my DROID BIONIC via Reliance Wireless
Click to expand...
Click to collapse
I did that but everytime I turn my phone back on it keeps showing CDMA only
Turn off radio...
Change it to cdma auto prl... wait for a while...
Turn radio on again....
And see...
sent from my DROID BIONIC via Reliance Wireless
matriX1218 said:
Turn off radio...
Change it to cdma auto prl... wait for a while...
Turn radio on again....
And see...
sent from my DROID BIONIC via Reliance Wireless
Click to expand...
Click to collapse
OK still no 3G or mms I have done this several time and nothing still looking at a blue 1x.
it says GSM Disconnects========DATA=======
cucci_slamr said:
OK still no 3G or mms I have done this several time and nothing still looking at a blue 1x.
it says GSM Disconnects========DATA=======
Click to expand...
Click to collapse
Pm me ill help get 3g and mms
Sent from my SGH-M919 using xda premium
JUSMEJOSE said:
Pm me ill help get 3g and mms
Sent from my SGH-M919 using xda premium
Click to expand...
Click to collapse
CLEAN SIM...only 1X I need real help...PMing you is not working as well either so I need a solution quick.
Don't want to pay for data I wont use!!!!
I upgraded mine... everything works flawlessly...
Pm me...
sent from Motorola DROID BIONIC on Reliance Wireless
I have mms but no 3g
I'm at the same build, version, etc as cucci_slamr. I have MMS and 1x but no 3G. Paid to have it flashed, really don't want to have to pay somebody else to redo flash just to get 3G. Any ideas? My network type is already set to CDMA auto (PRL). Thanks
Hi everyone,
I need NV Items to fix a RF issue with my phone where its not connecting to CDMA. if you have cdma workshop or DFS and this phone please help because this is my work phone.... im so close to fixing it but this is the final thing I need. please help
kalanir said:
Hi everyone,
I need NV Items to fix a RF issue with my phone where its not connecting to CDMA. if you have cdma workshop or DFS and this phone please help because this is my work phone.... im so close to fixing it but this is the final thing I need. please help
Click to expand...
Click to collapse
what u need i have all those but i am not able to call
it allows only first call.
in cdma only
in gsm all is fine
I managed to back up my nv items after I finally got it to read CDMA. whats the issue youre having?
rickin2011 said:
what u need i have all those but i am not able to call
it allows only first call.
in cdma only
in gsm all is fine
Click to expand...
Click to collapse
getting cdma network but can only make first call
kalanir said:
I managed to back up my nv items after I finally got it to read CDMA. whats the issue youre having?
Click to expand...
Click to collapse
getting cdma signal even can call but only once the signal is there but cannot make next call
again if i restart i am able to make first call.
in gsm every thing is working fine.
cons: cannot use cdma
i am in ruim only mode
rickin2011 said:
getting cdma signal even can call but only once the signal is there but cannot make next call
again if i restart i am able to make first call.
in gsm every thing is working fine.
cons: cannot use cdma
i am in ruim only mode
Click to expand...
Click to collapse
If I remember correctly, you need to be in an NV Item only mode. this is due to the sim card only being used for 4G LTE. I cant remember at the top of my head what I did cuz it was a bit ways ago but I know I did do a hard reset reflash as well as a ##RTN on it too.
Try from your dialpad
3845#*955#
Or
2945#*955#
Just a couple menus that might give you access to what you're looking for.