Hi guys,
When I connect a card reader/USB flash memory to the USB-port on the connected 4-in-1 cable, how to access these memories?
I also have an external hard disk, which has its own power supply (so no "too less power" issue), but the Athena doesn't do anything with it.
Do these attached memories need to appear as Storage drives in the file explorer?
Thanks.
I received my 4in1 cable yesterday and I found that it recognize hard drive randomly. I mean that not all USB memory are accepted by system. First of all it accepts only low voltage ones and not all are recognized. About mouse host...it recognize mouse but it's unable to show pointer, even with some drivers found on the this forum that should enable it...
So I would like to know what kind of commercial policy is this??? HTC says that with this cable and device you can host HD, mouse...but it's all pretentious, because to use it properly it's really hard!!!
I'm quite disappointed!
Again: when an USB storage device is connected, assuming it's a low voltage device, WHERE to access the memory??
It's an old thread, but what the hell. Plug your USB memory into your 4 in 1 cable. Use file explorer, go to "My Device" where you will see MicroDrive listed. Further down you will see "Hard Disk". That's it.
Thank you, this solves my problem.
http://www.palonek.ca/
asci said:
I received my 4in1 cable yesterday and I found that it recognize hard drive randomly. I mean that not all USB memory are accepted by system. First of all it accepts only low voltage ones and not all are recognized. About mouse host...it recognize mouse but it's unable to show pointer, even with some drivers found on the this forum that should enable it...
So I would like to know what kind of commercial policy is this??? HTC says that with this cable and device you can host HD, mouse...but it's all pretentious, because to use it properly it's really hard!!!
I'm quite disappointed!
Click to expand...
Click to collapse
mouse pointer works fine with me. Are you using wm6?
I don't think it's just a voltage issue with USB host on the x7500 - I just don't think it can cope with reading from large storage devices. Mine reads 1 gb and 2gb sticks fine. It also reads my 4gb and 8gb sticks but I experience drop-outs and slowdowns with the higher capacity sticks.
I should imagine that a 200gb HDD would send the x7500 loopy. Besides which I don't see the point in having a pocket pc with a mains connected hard drive wired to it. Might as well use a laptop as that would be more portable.
just wondering because there is a cf 2 to usb host card out there and there are SD to micro SD adapters but I can't seem to find cf 2 to SD but with it I think we could get usb host on any SD equiped ppc now that would be slick. Or is this just one of them things where you could cary over the pins on the compact flash2 card to sd or does it have to have the inbetween I have found plenty sd to compact flash but nothing the other way prolly because a device that would take a sd card could never house a compact flash card inside it but sense I am looking at having it all external prolly built into a compact powered usb hub its not a issue.
well im thinking if I take one of the sd to too cf2 adapters and pry it open I may be able to just solder it all togeather and get it to work without the adapter that im lookin for if I can get this working would anyone else be interested in have a usb host dongle for there vogue and ummm I think this thread may fall into the univeresal mod sense in therory it should work for any ppc with a micro sd card slot. So if a moderater would want to move this to the right thread thats fine with me.
ok more poking around and well look at this is it actually stating that it handles the usb host onboard? I feel pretty dumb sometimes and the wording makes it look like that could use some intput. http://www.supermediastore.com/sansdigital-mobilestor-ms1u-2-5-usb-enclosure.html#description
well from the website it says you can directly copy stuff from cards to a hard drive you have installed in this without the need for a computer so my thought is yeah it has usb host my only thought now is would it hook up to the usb port on the touch and be recongized it might need a special driver.
Hi all,
I am taking off for a month long vacation to Asia and India soon and am having a tough time imagining my life without a functional computer... so, what better alternative (along with my 3G phone) than then Nook Color...
but...
One of the most appealing concepts to me would be to use the NC as an "uploader" of pictures I will be taking with my SLR.
So, can this be done:?
1. take out MicroSD card from Camera and somehow, with some adapter, connect via the USB port on the NC.
2. Use an app to mount/view the MicroSD storage unit and copy to the NC storage, some/all of the pictures i want.
3. Use the SmugMug Andoird App and WiFi via NC to upload pictures while I travel.
>> I guess i could do this via the the mobile phone I'm bringing, probably by swapping the memory card on the phone and using the same app, but i believe the larger screen size and easier text input would make the NC perfect for this.
Thoughts?
Thanks ahead of time.
Check in the development section for the thread on usb host support. It tells you how to hook your camera to the nook with a usb cable, I've never tried it but a lot of people swear by it.
Sent from my ADR6300 using XDA App
I have NC with CM 7.1 stable on EMMC. I am able to use an unpowered USB card reader to transfer pictures off both full sized and micro SD's. Other than being on CM7 the trick is getting the correct cable. Here is the one I use:
Micro USB Host Cable (OTG Cable) - Xoom, Galaxy S2, Nokia N810 / N900, Toshiba TG01, Archos G9. New Version with more accommodating "L" shaped connect
Off Amazon.
You'd probably be better connecting directly to your camera, if your camera can do it. For many things connected using USB host you need a powered hub, but since the camera has its own power it probably doesn't need the hub.
Check out http://forum.xda-developers.com/showthread.php?p=17925389#post17925389
There's also at least one raw format decoder called RawDroid.
I haven't tried this, but I imagine you could use a microSD to SD adapter and just use microSD cards in your camera. Take the microSD out of the adapter, put it into the Nook and copy the photos over with a file manager. This would obviously cost you more money, as microSD (I believe) is more expensive than SD, but it would save you some hassle on the Nook side.
There are few ways to get this done but b4 trying one, make sure you meet all requirement.
1. Some members suggest you swapping the uSD. It's a fastest way BUT make sure you are running CM7 off eMMC if you're booting it off the uSD itself, then forget about this method.
2. If you Tx pix directly from camera to NC, make sure you do have the microUSB-to-whatever your camera USB connector type: miniUSB or USB, cable.
Awesome tips guys, thank you.
<<There's also at least one raw format decoder called RawDroid.>>
Can't imagine what that would be useful for unless all the shooting is done in RAW and you want to preview or something...
<<Micro USB Host Cable (OTG Cable) - Xoom, Galaxy S2, Nokia N810 / N900, Toshiba TG01, Archos G9. New Version with more accommodating "L" shaped connect >>
Great, being delivered tomorrow
511pf said:
I haven't tried this, but I imagine you could use a microSD to SD adapter and just use microSD cards in your camera. Take the microSD out of the adapter, put it into the Nook and copy the photos over with a file manager. This would obviously cost you more money, as microSD (I believe) is more expensive than SD, but it would save you some hassle on the Nook side.
Click to expand...
Click to collapse
This is what I do. Micro-sdcard w/ adapter in my Canon. Pop the card out, and put into the NC (after first uninstalling the card I normally have in there).
view pictures, copy them to internal memory, etc.
As stated above, you must not be running CM7 off the sdcard for this method to work.
I think it would also be possible to plug a flash drive in using an OTG cable (w/ power) and backup to that as well - I haven't tried that yet.
If you wanted to run cm7, you should be able to do the opposite - sdcard into a reader plugged into NC using OTG cable (w/ power?) and then copy to the sdcard that you are running cm7 from.
wow im interested in this, but do we really need a otg cable? since cm7 comes with usb-host support?
btw can the nc supply enough power to the card reader? or a 1-to-2 splitter so that the nc can be charged at the same time?
and what apps are suitable for this kind of usage?
wow the ipad got something like this already: http://terrywhite.com/techblog/archives/7657
but ipad are much larger... needs a backpack, nc can fit in a large pants pocket.
That's the cable that works for me. Plenty of power for the card reader.
i also use a microSD to SD adapter in my camera, and pop the microSD to copy the files in the internal memory of the nook (then, as i am a freak about not loosing my pics, copy them from internal memory to 2 backup microSD's)
i dont know if it impacts in anyway in the performance of the camera, i shoot with a 12 megapixels canon powershot in jpgs and 720p videos. i'm not very exigent with the transfer rate of the card
it seems that quickpic (https://market.android.com/details?id=com.alensw.PicFolder) is a good (and faster?) alternative to the built-in gallery.
what is needed... (for people who need to use a card reader) since the nook can only supply 100ma power...
1. a y-splitter cable (where can I find one? are there ready made ones?)
2. a usb charger
3. a microusb male to usb type-a famale
4. a card reader, of course
The cable I mentioned and a card reader work fine for me, no need for additional power.
Hi All,
I have what may seem a strange question for you... Is the Galaxy Note able to read information from other Memory Cards via its micro usb port?
Let me explain....
I am off on my travels fairly soon and am wanting to travel light. I will be taking my camera and Galaxy Note in lieu of a laptop.
What I am wanting to do, is view the pictures that I have taken on my camera (which only has a 3" screen) on my Note which obviously has a larger screen.
The cards that I use in my camera are micro SDHC in full sized SDHC adapters, so in theory I could take them out of the adapters and put them straight into the memory slot on the Note.
I don't really want to have to keep taking the back of the phone off to do this though, so I was wondering if I could slot the memory card, via a cable or adapter (which I have found on ebay) into the micro usb port on the bottom of the Note and it be able to read the contents of the card.
Does anyone know if this is possible?
Sorry for all the waffle but I need you to understand the method in my madness.
Thanks in advance.
Neil
if there are usb adapters for the same, then i guess it should work. because pen drives and few portable hard drives do work flawlessly when connected to the Note.
Thanks for the help Guys. My adapter arrived today and when I hook everything up, the images from the camera memory card show up in the Note's Gallery. Perfect!
If anyone is interested, here is the adapter that I bought....
http://www.ebay.co.uk/itm/300603100...X:IT&_trksid=p3984.m1497.l2649#ht_1966wt_1139
I then simply plug a usb card reader into the usb end and the micro usb end into the Note and away I go.
Cheers all.
Neil.
Hi guys.Just got my note 3 a few days ago and waiting for my samsung gear.It really pisses me off that the gear does not have bigger internal memory..I`ve been thinking and i will be trying something to fix this problem.
Adding an external sd slot.no soldering on the watch will be involved.The gear can still read usb sticks if you connect them through its special adapter and connect a otg cable.My idea is to add a very slim designed microsd pcb on the botton on the watch or around it and connect the cables with somekind of a magnet to the base.
Then change the mounting points located in vold.fstab from USB to external SD.
So what do you guys think?would this be worth it ?
totally worthless. it will become bulky and fragile. someone better work on bluetooth internet tethering so we can use internet apps on Gear.
i'd prefer to stream my files from my phone, instead having to keep them on Gear.
Stavr0s91i said:
Hi guys.Just got my note 3 a few days ago and waiting for my samsung gear.It really pisses me off that the gear does not have bigger internal memory..I`ve been thinking and i will be trying something to fix this problem.
Adding an external sd slot.no soldering on the watch will be involved.The gear can still read usb sticks if you connect them through its special adapter and connect a otg cable.My idea is to add a very slim designed microsd pcb on the botton on the watch or around it and connect the cables with somekind of a magnet to the base.
Then change the mounting points located in vold.fstab from USB to external SD.
So what do you guys think?would this be worth it ?
Click to expand...
Click to collapse
I don't believe that the Gear can support OTG as I have a cable and just tried that yesterday, unless you have gotten it to work, then I'm all ears