hello everybody,
today i installed the cm7 on my tp and as i rebooted it to install a next rom, the screen is now stuck at the main screen of moboot 0.3.5
the side buttons are moving just fine up and down and down up, but the power button will not work to select the option such as boot clockworkmod, boot cyanogen mod.
the power key does work fine because it was working fine during cm7
im not sure whats going on, so if somebody can help me it would be great thank you
I always use the Home button in Moboot to make the selection.
Related
I have CM7 RC2 installed on my nook emmc and it's been working great, but I want to flash dalingrins OC kernel... I flashed CWR through my Clockwork app and anytime I try to reboot into recovery it never does, just goes straight to the CM7 boot animation then boots normally... can anyone help? Thanks
I've noticed that the power button + N button combination on the Nook Color seems to be a lot more touchy and prone to error (i.e., not booting into recovery when pressing it) than the analogous key presses on my EVO.
Try holding down the N button, press the power button, and letting go of the power button about 2 seconds after pressing it (keep holding down the N button). I noticed if you hold it too long or not long enough, you'll go straight into the CM7 boot logo. This almost always works for me.
Right so the problem is thus, I am running MIUI 1.9.23 and used rom manager to install CWM. I was then able to boot to CWM from rom manager but if I turn my phone off and try and boot by holding vol down and power the phone will show the S/W updating standard LG recovery.
Now this wouldn't be a problem but I regularly mess round with my phone and it means that if i am unable to boot to my ROM then I can't boot to recovery and I have to reflash the stock ROM with smartflash. This all seems rather counter-intuitive.
Anyone know how i can rectify the situation?
You're doing it wrong
Hold both power and volume till the blue LG logo appears.
Ahh man that was dumb, I'm coming from the desire where you can release everything pretty much immediately. Cheers
Ahaha... Before I did something worse..
I hold it until the menu appeared, then I release, and rebooted!
(because "Reboot" is the first upper menu )
My Touch Pad went nuts and decided it wasn't going to boot. It will start to boot but only gets to the screen that says loading.. The next screen would be the boot animation but it never gets that far.
I have to hard rest the TP but instead of booting to the Moboot menu it just goes right by and keeps trying to boot cm10. So I stuck in loop hell.
I was trying to boot to recovery but I'm not sure you can without the menu.
Anyone have any ideas? I can get into USB mode but that's it. Haven't tried ADB but not sure if it boots far enough for adb?? another problem is my battery was at 15% so I have to do something fast once I turn it on as it would charge the way it is now.
HELP!?
Hold down a button such as one of the volume buttons while it is booting from a powered down state. Moboot cannot proceed with a button held down. You'll get a prompt to release all keys and you should then go into the moboot menu.
Sent from my slim_tenderloin using xda app-developers app
If you hold the volume up Button and press power till you see tha hp logo, you should go into the recovery mode right away!
pattyland said:
If you hold the volume up Button and press power till you see tha hp logo, you should go into the recovery mode right away!
Click to expand...
Click to collapse
Well that's how its supposed to work. But once I let go of keys it starts to boot into moboot (I can see the screen) but then there is no actual menu and it just automatically starts booting CM10 again.
Anyways I found the ACME un-istaller and was able to run it before my battery totally died (it was at 5%) and at least now I'm back to WebOS and fully charged. I guess I"ll have to reinstall all the Android stuff from scratch. But WebOS isn't all that bad and actually work very well, if only their was app support.
Thanks for your help though.
Sorry for the possibly FAQ nature of the request. I installed CM9 probably over 18mos on my daughter's Touchpad and was going to update it to JCSullins CM11 ROM. I got all the files downloaded and was getting ready to perform the complete uninstall of CM. Once I rebooted into the moboot 0.3.5 menu I was trying to select the 'boot webOS recovery' option, but no combination of power button + vol up or down seems to do anything except move the menu selection up/down. I can't seem to do anything to actually 'select' an option from the menu. I've tried long press power and short press power both with and without the vol up/down held. I'm hoping I can avoid having to open the unit to disconnect the battery but right now I'm not sure what I can do. Again it's been a long time since I did anything with the Touchpad and when I did the initial CM9 install everything went very smoothly once I got Novacom installed and ran the ACMEInstaller script. I'm hoping there's a simple trick I missed that will help get me out of the moboot screen.
-OK - sorry for the idiot post here, I just figured out the select is the 'front' button on the screen. Feel stupid but got it working! Hopefully I'll have the new CM11 up and running for my daughter tomorrow !
My home button has stopped working on my TP. I'm currently stuck on the mobot 0.35 screen. volume rockers work to move cursor up and down to select webos or Android but home button to select wont work. Seems I can only wait for the battery to die and then let it reboot naturally since holding the power button and the volume rocker doesn't seem to reboot in Mobot screen.
Going forward I'd like to restore home button functionality. it stopped working some time ago. Should I open up HP TouchPad and see if I can fix the issue with the contacts of the home button? Don't know if thats easy or if I'm capable of. Or is there another way to install a newer Android version for me without a functional home button? thx!
Older install methods and iFixit guide
leif2 said:
My home button has stopped working on my TP. I'm currently stuck on the mobot 0.35 screen. volume rockers work to move cursor up and down to select webos or Android but home button to select wont work. Seems I can only wait for the battery to die and then let it reboot naturally since holding the power button and the volume rocker doesn't seem to reboot in Mobot screen.
Going forward I'd like to restore home button functionality. it stopped working some time ago. Should I open up HP TouchPad and see if I can fix the issue with the contacts of the home button? Don't know if thats easy or if I'm capable of. Or is there another way to install a newer Android version for me without a functional home button? thx!
Click to expand...
Click to collapse
Android should be the default boot option for moboot. You could try using the older install methods with the ACMEInstaller5 here if you're desperate to get android working again. Try using a newer rom below.
Download Android 4.4.4 Kitkat install files(Rom, Recovery, Gapps):
Rom:Download the latest Lineage11 build
Recovery:TWRP-jcs-dm-tenderloin-20140612b.zip
Gapps:gapps-base-arm-4.4.4-20170902-1-signed.zip
Note: Do Not unzip the files.
Repairing the actual button could be tricky but there's an iFixit guide here HP TouchPad disassembly guide on youtube here