(Q) Full brick! please help!!! - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

I tried to install stock rom after CM9 was installed in my device.
odin got stuck in the middle and after that when I tried to open the device I was stuck in the "galaxy note N-7000" screen, and it wouldnt go into recovery, only to download mode.
when I tried to use odin again it got stuck in:
<ID:0/011> NAND Write Start!!
so I read this thread:
http://forum.xda-developers.com/showthread.php?t=1607011&highlight=nand+write+start
so I tried to flash the PIT file and odin got stuck again.
after that I pulled the battery out and now the power button wont do anything!
not even the smallest light on the screen.
I also tried to use combination with volume and home screen button. still nothing!
what do I do???
(I also tried to use another fully charged battery! still nothing!)

ykurtser said:
I tried to install stock rom after CM9 was installed in my device.
odin got stuck in the middle and after that when I tried to open the device I was stuck in the "galaxy note N-7000" screen, and it wouldnt go into recovery, only to download mode.
when I tried to use odin again it got stuck in:
<ID:0/011> NAND Write Start!!
so I read this thread:
http://forum.xda-developers.com/showthread.php?t=1607011&highlight=nand+write+start
so I tried to flash the PIT file and odin got stuck again.
after that I pulled the battery out and now the power button wont do anything!
not even the smallest light on the screen.
I also tried to use combination with volume and home screen button. still nothing!
what do I do???
(I also tried to use another fully charged battery! still nothing!)
Click to expand...
Click to collapse
I am afraid that nearest samsung service centre is the next step my friend.

so you're saying after you pulled the battery and got it back in it doesn't goto download mode ? if you have a JIG try using it to force DownloadMode in case it does work and the pit doesn't work try re partition option with odin the partition (hopefully) just got messed and not the MOBO....

abhisahara said:
I am afraid that nearest samsung service centre is the next step my friend.
Click to expand...
Click to collapse
Not just the next step, but the only step...I second what Abhi said.

Related

[Q] Help! Woke up this morning and phone won't turn on!

I woke up this morning and my phone won't turn on! I hold down power and see the Samsung splash screen... then the display goes off and nothing happens. I can't launch into recovery mode... I can launch into Download Mode, but can't do anything from there... (no response to any buttons)
I tried pulling out the battery and SIM - to no avail...
I am running a rooted Bell phone with the lag fix.
Please give me suggestions! What do I need to do to recover this using my PC and adb?
Time to recharge your SGS?
Before i give you the bad news
try Flashing the phone with Odin, see if you can complete a successful flash
However you'll most likely see an Odin error concerning mounting the drive, your Internal SD drive is most likely dead, and it'll need to be replaced by Samsung/Bell service center.
there are many known cases like this related to the lag fix
slaman said:
I woke up this morning and my phone won't turn on! I hold down power and see the Samsung splash screen... then the display goes off and nothing happens. I can't launch into recovery mode... I can launch into Download Mode, but can't do anything from there... (no response to any buttons)
I tried pulling out the battery and SIM - to no avail...
I am running a rooted Bell phone with the lag fix.
Please give me suggestions! What do I need to do to recover this using my PC and adb?
Click to expand...
Click to collapse
atan.ismail said:
Time to recharge your SGS?
Click to expand...
Click to collapse
It's fully charged... it was charging all night. What's weird is that I've plugged it in and it's flashing the battery symbol.... I can't turn off the screen - it keeps flashing this symbol
slaman said:
It's fully charged... it was charging all night. What's weird is that I've plugged it in and it's flashing the battery symbol.... I can't turn off the screen - it keeps flashing this symbol
Click to expand...
Click to collapse
if you hold the power button, does it turn on at all?
how far does it go into the boot process?
does it get stuck after the pretty Galaxy S swirling logo?
AllGamer said:
if you hold the power button, does it turn on at all?
how far does it go into the boot process?
does it get stuck after the pretty Galaxy S swirling logo?
Click to expand...
Click to collapse
I don't get the swirling logo... I just get the static splash page "Samsung Galaxy S" - it stays for about a second, then the screen goes black.
I'm trying to figure out what to do once I'm in download mode... I have Samsung Kies (which won't detect it...) and Odin (which won't detect it)
slaman said:
I don't get the swirling logo... I just get the static splash page "Samsung Galaxy S" - it stays for about a second, then the screen goes black.
I'm trying to figure out what to do once I'm in download mode... I have Samsung Kies (which won't detect it...) and Odin (which won't detect it)
Click to expand...
Click to collapse
that doesn't sounds right
try installing Odin on another machine
seems like the PC you are trying to use has the USB port locked up.
i've had that happen on mine before
if you turn off the PC, remove the power cord
power it on, then put the power cord
and power it on again
that should reset it
Ok, Odin seems to recognize the phone (it installed all the drivers when it was in Download Mode) - I clicked "start" and got the following:
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> Removed!!
then the phone went back into the flashing battery symbol... I need to grab the official Bell Samsung Galaxy S .pit file I guess.
Samsung Kies just sat there trying to connect when the phone was in Download Mode...
Okay, so I've downloaded the 0803.pit file... I just need to know which firmware to flash it with under PHONE, PDA, CSC, and DUMP...
Would really appreciate the help!
JH2 firmware for all 3 and flash with correct pit file and click partition (but will wipe all data).
rmanaudio said:
JH2 firmware for all 3 and flash with correct pit file and click partition (but will wipe all data).
Click to expand...
Click to collapse
I found the thread for JH2, but none of the links in it work!
http://forum.xda-developers.com/showthread.php?t=755063
Got one that you can spare?
Also, 0803.pit works for JH2 right?
Really appreciate your help!
I'm just going to try to find JG9 and upgrade via Samsung Kies... that's if I can find JG9 - these are so hard to find!
Hi Mate,
I just had the same problem - could not reboot from normal recovery, could not reboot from clockworkmod recovery. I had to launch nandroid recovery.
On my unit, it seems that the problem was caused by a conflict between setcpu profiles and the alter minfree settings from ryanza's oclf.
If you have clockworkmod installed and have backed up your rom, you should be able to use nandroid recovery.
I have now changed setcpu not to run on boot, and have not used alter minfree - prob seems to be sorted.
Hope this helps (you or somebody else).
Regards, Paul.
Go here to download firmware: http://www.samfirmware.com/firmwares.htm
rmanaudio said:
Go here to download firmware: http://www.samfirmware.com/firmwares.htm
Click to expand...
Click to collapse
Saw that.. but there's no I-Series... I can't see any firmwares for Samsung Galaxy S there - am I blind?
EDIT: Found it - thanks.
This JH2 on his site is the "updated" version of JH2 that fixes the 3-button recovery as per the Facebook page right?
http://www.facebook.com/note.php?note_id=10150262535205538&id=260085296049
or is this the "earlier" version of JH2?
http://www.multiupload.com/ZNBT2RY5Y0
Use 512 pit file.
http://samfirmware.webs.com/samsungandroid.htm
Top left, just had to click on "android phones" to get here... good luck!
slaman said:
Saw that.. but there's no I-Series... I can't see any firmwares for Samsung Galaxy S there - am I blind?
Click to expand...
Click to collapse
It is there...dont look for I series...click on Android. Then grey area for america files.
Got the file... tried to update through Odin... and it's stuck on the following for 15 minutes...
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> zImage
The phone still shows Download mode.
Do I need Odin v1.3 or is Odin v1.0 sufficient? Using PIT0512
EDIT: Pulled out battery... tried again... now see blue status bar moving along the bottom... fingers crossed that this works!
It completed... and same thing is happening. Can't start it up...

Bricked?! Halp!

Got an at&t tab here, I upgraded to JM6, flashed the modem, and rooted it, all was well, untill I realized that I couldnt get into recovery to wipe. So I went into d/l mode, and couldnt get out, loaded up Odin3 and attempted to flash the bell modem again just to get it to reboot. Well it froze up, and now all I get is a communication error picture: "phone ----- !-----PC"
Help please, its brand new and going to be sold
From my experience you can power off the unit, put it in dl mode again flash the Bell modem with no partion, no pit and with reboot selected and it should do a regular startup!
Sent from my GT-P1000 using Tapatalk
I lost d/l mode. But somehow the second time I attempted to flash JM6 with odin, while seeing this error message, it worked. So its working again.
But I have no recovery anymore is this normal?
UPDATE. Seems after JM6 I have no recovery and no bootanimation(have sound). I get a black screen with a thin vertical line on the right side of the screen. Any advice would be great
The phone --!-- computer problem is solvable.
Power off your phone, and power it back on with holding the volume down button, when you see the --!-- sign release the buttons.
You are now in download mode, although you cant see the little android with the shovel. Connect it to a pc with an odin 1.7 open and you will be able to reflash it.
When I got the error picture: "phone ----- !-----PC" after messing with JM6, I just reflashed it at that screen with the full JM6 package. I dont think you can downgrade from JM6...
I just flash pit file at the phone ----- !-----PC screen then when it reboots it will boot loop. Turn it off then hold vol down and power then when the screen turns on let go of power button but still hold vol down. That will get you in download mode. You can downgrade form JM6 but you have to try 3 to 6 times before it will work. JM6 to jj4 then at&t rom is how I do it.
shep211 said:
I just flash pit file at the phone ----- !-----PC screen then when it reboots it will boot loop. Turn it off then hold vol down and power then when the screen turns on let go of power button but still hold vol down. That will get you in download mode. You can downgrade form JM6 but you have to try 3 to 6 times before it will work. JM6 to jj4 then at&t rom is how I do it.
Click to expand...
Click to collapse
You can downgrade ? Make your guide a bit better please so we can all use it.
shep211 said:
I just flash pit file at the phone ----- !-----PC screen then when it reboots it will boot loop. Turn it off then hold vol down and power then when the screen turns on let go of power button but still hold vol down. That will get you in download mode. You can downgrade form JM6 but you have to try 3 to 6 times before it will work. JM6 to jj4 then at&t rom is how I do it.
Click to expand...
Click to collapse
Interesting that you claim you can get back to JJ4 from JM6. All i get is boot.bin error so id like ro know how you did it?
Sent from my GT-P1000 using XDA App
Cmon guys, read the thread. I got the error fixed, now I have no recovery or boot animation.
Does the tab boot up at all? if it does you can try and do a factory reset from settings and see if that clears it up. You will loose all your settings and third party apps but this seems to be a requirement after flashing
Sent from my GT-P1000 using Tapatalk
Tab boots up fine, everything works, I just have no recovery or bootanimation, the sound plays for the bootani, just no picture.
MotoMudder77 said:
Cmon guys, read the thread. I got the error fixed, now I have no recovery or boot animation.
Click to expand...
Click to collapse
You need to tell us what filename you flashed and what .pit file if any you partitioned with.
It sounds like you flashed P1000OXAJM6.tar without partitioning which is probably not going to work.
Never put the phone into download mode unless you have a file ready to flash.
Flashing the file in my sig will probably fix your Tab.
rotohammer said:
You need to tell us what filename you flashed and what .pit file if any you partitioned with.
It sounds like you flashed P1000OXAJM6.tar without partitioning which is probably not going to work.
Never put the phone into download mode unless you have a file ready to flash.
Flashing the file in my sig will probably fix your Tab.
Click to expand...
Click to collapse
I followed the instructions in the OP of the JM6 thread, and flashed the files that I was linked to in the OP. I checked the box to partition. After I flashed the bell modem as I am on At&t. Then I rooted via SuperoneClickv1.5.5.
Now I have no recovery or boot animation.
I was already d/ling your file to check if that fixes anything.
Ok I tried your(rotohammer) file, and still no luck, it did save me from the root proccess tho.
adb reboot recovery, and adb devices will show the device is in recovery, but I have a backlit screen with a thin line down the right side of it. Which is the same thing I see during boot, after the at&t image.
At startup I will see this screen untill I press the lock button twice, first time shuts the screen off, and second unlocks as normal.
MotoMudder77 said:
Cmon guys, read the thread. I got the error fixed, now I have no recovery or boot animation.
Click to expand...
Click to collapse
I answered your problem yesterday and you didnt pay attention to it i guess.
This Video say it all....! http://www.youtube.com/watch?v=nmpWC73pig4
ive seen the screen you are talking about i messed up and flashed the pda file in the wrong place, what i did though is flashed the Stock ATT firmware in the pda section didn't select partition and this file seemed to re-flash everything there is a thread here in the forum, it should be on the first or second page
better yet here is the link http://files.deodexed.com/ModADroid-Galaxy-Tablet/T-Mobile/ATT_Stock.zip

[Q] Stuck at logo screen....help

I was trying to flash a GPS fix, this one..
http://forum.xda-developers.com/showpost.php?p=10389365&postcount=18622
I forgot to read the instructions and went ahead and flashed it through CWM, now its stuck at the Samsung logo screen and I cant get into recovery, it just loops, I can get into download mode, but I`ve never used it, some help.....please
mloc33 said:
I was trying to flash a GPS fix, this one..
http://forum.xda-developers.com/showpost.php?p=10389365&postcount=18622
I forgot to read the instructions and went ahead and flashed it through CWM, now its stuck at the Samsung logo screen and I cant get into recovery, it just loops, I can get into download mode, but I`ve never used it, some help.....please
Click to expand...
Click to collapse
This procedure will get you back to stock JPU ROM via Odin and Download Mode.
http://forum.xda-developers.com/showpost.php?p=10449932&postcount=7
Then once your phone is working again you can go ahead and flash to a custom ROM which I'm guessing you know how to do. Let me know!
Ok dude I`m doing it now, fingers kriss crossed!!!
Ok this happened....
I took usb out, restarted pc, then phone went into recovery mode, I did a factory/data wipe, same with cache, was about to restart phone, now there`s a white box with an orange arrow comming out of it and a little green android man?
I pressed menu button, it brought up recovery, I restarted, went passed the white logo screen to swirling S logo screen, also played music, now at black screen....
Still in black screen but every 20 or so seconds it vibrates once then 3 quick times???
After sometimes it is required to do a factory reset to get it working.If your flash was succesfull try to factory reset it in recovery mode.
Tried Odin again and got the same error, so when I get into recovery mode I should factory reset everything?
Tried to get back into recovery from download mode and got the bricked screen!!! Its hopeless now is`nt it
I can still get into download mode.....
I dont really get what you are trying to do.
Can you get in recovery mode and do a factory reset???
I was in recovery and did that and it got to the swirling S logo screen then screen went black, vibrated once then 3 short ones every 30 or so seconds and thats it, it did`nt go any further.....
I keep getting a FAIL when I try to flash using Odin
I notice when I`m putting in the info in to PDA PHONE CSC areas, I dont see where I`m supposed to use this..
MODEM_I9000XXJPU.tar.md5
I followed it all step by step, or i dont see it in the steps
Hmm i had that screen many times but always able to flash with Odin.Are you sure you got the drivers on your pc?Make sure that you havent Kies running,on try or in backround,or any other program that is used to connect your phone.Also its always good to use a free USB port on your pc,and by saying free i also mean that it not one of the front panel USB cuz those ones sometimes are shared.
Start at the beginning .
Available
Download mode yes or no
Recovery mode yes or no
PC sees phone Odin first box is yellow yes or no
jje
mloc33 said:
I was in recovery and did that and it got to the swirling S logo screen then screen went black, vibrated once then 3 short ones every 30 or so seconds and thats it, it did`nt go any further.....
I keep getting a FAIL when I try to flash using Odin
I notice when I`m putting in the info in to PDA PHONE CSC areas, I dont see where I`m supposed to use this..
MODEM_I9000XXJPU.tar.md5
I followed it all step by step, or i dont see it in the steps
Click to expand...
Click to collapse
Modem = phone
gtg2 said:
Modem = phone
Click to expand...
Click to collapse
Still though,he should be able to flash even without modem file...
I m wondering if he clicked repartition or not.My guess is he didnt,so its stuck untill he does repartion.
JJEgan said:
Start at the beginning .
Available
Download mode yes or no
Recovery mode yes or no
PC sees phone Odin first box is yellow yes or no
jje
Click to expand...
Click to collapse
Yes
No
Yes
tackygr said:
Still though,he should be able to flash even without modem file...
I m wondering if he clicked repartition or not.My guess is he didnt,so its stuck untill he does repartion.
Click to expand...
Click to collapse
Repartition was checked, should I put the modem one in the phone section?
2. Open Odin AS the Man said .
Download here: http://db.tt/QuA1G6s
That is a sure working Odin. The one I use. Extract that and run Odin3 v1.3.exe
3. In Odin:
check Re-Partition
Click PIT and select s1_odin_20100512.pit
Check and click PDA and select I9000XXJPU-REV03-PDA-low-CL747761.tar.md5
Check and click PHONE and select I9000XXJPU-REV03-PDA-low-CL747761.tar.md5
Check and click CSC and select GT-I9000-CSC-MULTI-OXAJPU.tar.md5
Do not touch any of the other options. Leave them the way they are.
3. Exit Kies (make sure it is not running AT ALL).
4. Put your phone into DOWNLOAD mode (volume down + power + home) and plug into your computer
5. Click START in Odin... if Odin gets stuck for a LONG time (progress bar isn't moving at all in both phone and Odin).. unplug phone, pull battery, restart computer and repeat from step 2.
6. Once Odin says it succeeded wait for phone to reboot.
I`m still getting a FAIL on it.
I download that Odin, reinstalled the Samsung drivers and disabled anything related to the phone.
I tried it even without the sim car and sd card in cause I read one post that had tried it and it worked.
From the instructions it looks like I`m using 3 of the 4 files download, remember that modem one.
I definitely have to use that same file twice for PDA and phone?
I followed these instructions to the letter...
file:///C:/Users/Colm/Desktop/xda-developers%20-%20View%20Single%20Post%20-%20[Q]%20i9000%20can%20not%20boot.htm
I`m not sure which one is the right Odin to use, but I tried the both of them and still the same results.
There both v1.30, the gt-p1000 is the one from the previous post..
I`m even trying different USB ports...
Ya fuppin BEAUTY, I did it, I put into the phone section in Odin that modem file and here`s what I got...
NoW I have fireware 2.2.1
Baseband jpu
Kernel 2.6.32.9
[email protected] #1
Build
Froyo.xxjpu
Is this the new froyo?
Will I be able to go back to Darky`s 8.0?
Would this also mean I`ve 3E instead of 2E?
Is this the new froyo?
Says Froyo
Will I be able to go back to Darky`s 8.0?
On your own head be it all i have done for a week is answer borked post all using this rom .
Would this also mean I`ve 3E instead of 2E?
Probably flash via Odin you will need to search i dont have a link .
CF-Root-XX_XEU_JPY-v1.3-BusyBox-1.17.1
Its probably on Darkys front page as is Clockwork .
Install sd card update zip CWM twice to get to 2e .
jje
Ok first of all I want to thank the 2 of ya`s for all your help, I really appreciate it!!!
Now that I`m up and going for some reason my pc does`nt see my phone even tough it says I`m connected on my phone?
I restarted my pc, reconnected phone nothing...
If its not one problem its another...

Firmware upgrade encountered an issue Message.

Hello, guys.
I was trying to install a new rom to my Galaxy Note. and when wiping out the user data (to get the phone ready to install the new rom) he phone reboot and got stuck on the start up logo. Waited for a long time but it didn't do any thing. So a remove the baterry and turned it back on. But but it did the same.
I then decided to flash it using Odin but it got stuck almost at the end of the proccess. Now my battery is almost dead and the only thing on the screen is a flashing message. Firmware upgrade encounter an issue.
HELP!!! THIS IS MY NEW PHONE!!!!
estebandilone said:
Hello, guys.
I was trying to install a new rom to my Galaxy Note. and when wiping out the user data (to get the phone ready to install the new rom) he phone reboot and got stuck on the start up logo. Waited for a long time but it didn't do any thing. So a remove the baterry and turned it back on. But but it did the same.
I then decided to flash it using Odin but it got stuck almost at the end of the proccess. Now my battery is almost dead and the only thing on the screen is a flashing message. Firmware upgrade encounter an issue.
HELP!!! THIS IS MY NEW PHONE!!!!
Click to expand...
Click to collapse
Which rom you were on before trying to flash? And what did you try to install?
Sent from my GT-N7000 using xda premium
I was on Android 4.0.3 the German realesed.
N7000XXLPY---------4.0.3---------2012 May
I downloaded it from the forum and it was working nicely. I just wanted to try a different rom. But I didn't get to do nothing just to clear the data which never ended and crash my phone..
Stuck after wiping user data, Odin hanging at the end..where exactly did it stop working?
I'd say that it's definitely superbricked.
you can do that:
- go on recovery (Try vol up + home + power)
- mount usb storage and put abyss kernel in a directory
- flash abysskernell4.00
- reboot recovery
- wipe data cache and dalvik
- power off
- power on
if it's stay on boot logo :
- power off
- vol down + home + power (download mode)
- flash your note with odin pc with this method
- dl mobil odin and flash ics open germany with this method
Noizy.
I will try that, but now i have to charged my battery to be able to do it.
When trying to flash the green bar on Odin gets almost to the end ot the proccess but then it just sits there and doesn't do anything...
estebandilone said:
I will try that, but now i have to charged my battery to be able to do it.
When trying to flash the green bar on Odin gets almost to the end ot the proccess but then it just sits there and doesn't do anything...
Click to expand...
Click to collapse
Could you paste the Odin log perhaps? That would help the people around here give you a solution, if any.
Right now I am downloading the files from the commment above... I will try that and post whatever it happened!!! My internet conection is just a Mega so it takes me a while to download all the files to try it... But I am almost done!!
This is what I have on Odin. It almost get to the end of the green bar.
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> factoryfs.img
<ID:0/012> NAND Write Start!!
This is the message Showing..
Is your LPY Rom rooted? If yes, then how?
Did you flash CF-Root LPY kernel, or did you root it using Dr.Ketan's method?
This is a screen shot of the screen.
Yes it's rooted and I used Dr.Ketan's method..
I'm afraid you have a brick on your hands, mate. Take your Note to the
nearest service centre for MoBo replacement.
That I can't do. I bought from a third person... So I don't have any warranty... Let me ask you a question. The fact that I can get into recovery mode doesn't make a difference?
estebandilone said:
This is a screen shot of the screen.
Click to expand...
Click to collapse
Duno if this method will work for u but it works for me n my friend...
1stly i pressume u are able to boot into download mode...
2ndly, d/l a rooted GB Rom...
3rdly, restart pc/lappy
4thly, change another USB port (changed port works for me n my friend)
5thly, fire up PC Odin... put Note into download mode n connect...
Lastly select the rooted GB rom under "PDA"..
keep finger cross
Noted From My G.NOTE Using XDA Premium
I am trying again.
Not working... Don't know what to do
It's superbricked, for sure. All you can do is send it for repairs - motherboard replacement.
[Solve on [email protected]] Similar Case for reference
estebandilone said:
Not working... Don't know what to do
Click to expand...
Click to collapse
Hey dude, I had a similar case when I was upgrading my S2 officially because my USB was loose, I got the update 60% and came to a halt, my phone wasn't even rooted by then.
Here's what I did and here's what you can try:
1. root my phone (for your case, re-root your phone or even unroot then re-root it again, there may be some files damaged when your phone lost power).
2. install original kernel and Stock ROM (there might be original files which are needed from the original to make things work when you switch ROMs)
3. reboot and see if things are fine.
If you get back to running normal, then you can install whatever Custom ROMs you like.
Hope this help! Get back to me with the latest situation.

[Q] Cannot run my S I9000

Hi there!
I got this samsung galaxy s i9000 and i was using miui rom. there were a few things i didn't like so i wanted to switch to some other but when i turned of my mobile and used 3 buttons combo it only loaded to a downloading mod with this big yellow sign and was stucked there. so i wanted to turn it on normally but it only shows the galaxy s logo and afterwards screen with "powered by mackay kernel" and that cycles.
Is there a chance that me removing clockwork mod could cause that?
Need to fix that as soon as possible. Any advices?
AW: [Q] Cannot run my S I9000
The yellow triangle is the download mode and it's like fast boot mode on other device. It's a default feature.
If you are stucked a reboot you could try to pull the battery out for example 5min and wait, normally it fixes itself.
Sent from my Nexus 7
yes i read that a lot but it didn't work... even after half an hour i tried to turn it back on and it cannot load itself... and i have no internet connection either by t-mobile
also when i was inastaling miuis rom i used the 3B combo and it opened some sort of text mod where i chose to install it now it don't happen
Odp: [Q] Cannot run my S I9000
joasisk said:
yes i read that a lot but it didn't work... even after half an hour i tried to turn it back on and it cannot load itself... and i have no internet connection either by t-mobile
also when i was inastaling miuis rom i used the 3B combo and it opened some sort of text mod where i chose to install it now it don't happen
Click to expand...
Click to collapse
That text mod is called recovery mod. Press VolUp + Home + Power buttons. Then you may try to install rom again and reboot, after that phone should run.
AndroidCi said:
That text mod is called recovery mod. Press VolUp + Home + Power buttons. Then you may try to install rom again and reboot, after that phone should run.
Click to expand...
Click to collapse
problem is that i cannot get there it does the same thing as if i try to turn it on normally - cycling between samsung logo screen and mackay kernel screen
joasisk said:
problem is that i cannot get there it does the same thing as if i try to turn it on normally - cycling between samsung logo screen and mackay kernel screen
Click to expand...
Click to collapse
If you can reach the download mode, you should try to change your kernel via Odin. I don't know what kind of kernel you can use with your ROM but I'm pretty sure you can change it.
If it doesn't work with changing the kernel, try to change your ROM via Odin with download mode.
You need to have safe base.
If you have a problem with getting to cwm through 3-button combo try this:
pull out your battery, press vol up + home + power and insert battery, when your screen get on instantly release buttons.
From some time that's the only way to get into CWM on my SGS.
ok so i tried to flash odinrecovery but odin got stucked at nand write start...
joasisk said:
ok so i tried to flash odinrecovery but odin got stucked at nand write start...
Click to expand...
Click to collapse
What about flashing a new kernel? Not a recovery.
And did you try kronos111's method?
kronos111 said:
If you have a problem with getting to cwm through 3-button combo try this:
pull out your battery, press vol up + home + power and insert battery, when your screen get on instantly release buttons.
From some time that's the only way to get into CWM on my SGS.
Click to expand...
Click to collapse
didn't work now it don't even get to that loop it is stucked on black screen only able to get to download mode
Tell me more about your ROM.
What is your Android version? Your kernel? And what's the name of your ROM?
Cassis1978 said:
Tell me more about your ROM.
What is your Android version? Your kernel? And what's the name of your ROM?
Click to expand...
Click to collapse
I had MIUIs rom it was flashed in december but i don't remember the version and i had mackay kernel
Go into download mode and flash your miui kernel once again as PDA - odin or haimdall. If your phone still doesn't boot than you'll have to flash 3-file GB with pit and re-partition. I use JW1 for this kind of reseting system
kronos111 said:
Go into download mode and flash your miui kernel once again as PDA - odin or haimdall. If your phone still doesn't boot than you'll have to flash 3-file GB with pit and re-partition. I use JW1 for this kind of reseting system
Click to expand...
Click to collapse
actually i cannot find any kernel in .tar or any manual which files from zip should i put in tar file
i suppose you had JB MIUI so you can use semaphore kernel if it was 4.1 use 2.6.5 if 4.2. latest version
kronos111 said:
i suppose you had JB MIUI so you can use semaphore kernel if it was 4.1 use 2.6.5 if 4.2. latest version
Click to expand...
Click to collapse
got this with booth of them
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
than nothing
change USB port, connect cable directly to motherboard (no USB hub)
kronos111 said:
change USB port, connect cable directly to motherboard (no USB hub)
Click to expand...
Click to collapse
using laptop no hub after about half an hour i got
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
failed also on other port
heimidal don't even recognize the phone when i connect it...
phone only turns into downloading mod now anithing else... :crying:
joasisk said:
heimidal don't even recognize the phone when i connect it...
phone only turns into downloading mod now anithing else... :crying:
Click to expand...
Click to collapse
It seems that Odin recognizes your phone.
Do you have Kies on your computer?

Categories

Resources