Related
Let me start by saying, Power + Home does not work. Yes, really. I know there are a dozen threads about Touchpads not turning on, and they all have "Hold power and home for 20s" as the reply. Please don't respond with "Hold Power and Home for 20s". I have tried it.
Background
I took my Touchpad with me on a road trip. I did not have an official car charger, but I had one rated at 1 amp. I used this charger with my Touchpad, and it said that it was not powerful enough (as expected). I figured I would let the Touchpad at least get some juice while it was not being used. The battery steadily drained over the next couple of days, to the point where the screen did not come on. I assumed this was because the Touchpad was completely drained.
Once I got to a location with an actual outlet I used the original Touchpad wall adapter and let it charge for a few hours. The screen still did not come on, and there was no response (sound/light/vibration) from any buttons. I let the Touchpad continue to charge over night with the same result.
The Touchpad has alpha 2 on it.
What I have done
I have tried:
Power + Home for 15s
Power + Home for 30s
Power + Home for 1min
Power + Vol Up for 15s
Power + Vol Up for 30s
Power + Vol Up for 1min
Power + Vol Up + Home for 15s
Power + Vol Up + Home for 30s
Power + Vol Up + Home for 1min
All of the above with and without the Touchpad being plugged in to the wall and PC.
Trying WebOS Doctor (does not recognize a device)
Trying novacom directly (does not recognize a device)
Letting the Touchpad charge for > 1 day and repeating all of the above
Letting the Touchpad sit on the Touchstone for > 1 day and repeating all of the above
Verifying that the AC adapter is secured properly and repeating all of the above
Changing the USB cable and repeating all of the above
Changing the AC adapter and repeating all of the above
Results
The only time I have gotten any indication that the Touchpad is actually doing something is when using Power + Vol Up (and Vol Down) with the Touchpad connected to the PC. Vol Up has the Touchpad recognize as Palm. Vol Down has the Touchpad recognize as QHSUB_DLOAD. If I have the Touchpad connected to the PC in one of these states, Power + Home will reset the device (and Windows will not recognize it until I use Power + Vol Up/Down again).
That is the only response I get from the Touchpad. Anything else I have tried results in nothing.
My current plan is to attempt to let the battery completely drain, and then charge it again. I was previously under the impression that my Touchpad was out of power, but the testing with Vol Up/Down has shown me otherwise. My hope is that losing all power will truly "reset" the device.
Does anyone have any advice on anything else I should try? Is there a way to recover the Touchpad via booting it as Palm or QHSUB_DLOAD?
Volume Up + Power while connected to PC, then run WebOS Doctor?
You may have done this, but have you tried pressing home first and then holding it and power together? I couldn't get mine to start by pressing power and then home, but when I held home first and then power it came right on. If you have done that then disregard this, but if not I hope it helps.
Another method
Try power and Volume down. Hold for a minimum of 30 seconds before giving up. It has worked twice for me when all else failed.
FishDoc
That was very thorough. Once my TP died completely. I plugged it in and it didn't do anything. When I held Power + hitting home 15 times, it would give mea low battery indicator.
I plugged it in and left it over night. By the morning it was on 100%.
DJ_SpaRky said:
Volume Up + Power while connected to PC, then run WebOS Doctor?
Click to expand...
Click to collapse
It may not have been clear since it came after the list, but I did try this. WebOS doctor does not recognize the device in any mode. I do not know if this is simply because I lack the necessary drivers when it is in one of the other device modes. On the off chance that I didn't I will try again when I get home.
Dbarker 2 said:
You may have done this, but have you tried pressing home first and then holding it and power together? I couldn't get mine to start by pressing power and then home, but when I held home first and then power it came right on. If you have done that then disregard this, but if not I hope it helps.
Click to expand...
Click to collapse
I do believe I have tried this, but I will try again when I get home.
FishDoc said:
Try power and Volume down. Hold for a minimum of 30 seconds before giving up. It has worked twice for me when all else failed.
FishDoc
Click to expand...
Click to collapse
It is my fault for leaving it out, but I tried this after exhausting the other options.
chrischoi said:
That was very thorough. Once my TP died completely. I plugged it in and it didn't do anything. When I held Power + hitting home 15 times, it would give mea low battery indicator.
I plugged it in and left it over night. By the morning it was on 100%.
Click to expand...
Click to collapse
I really wanted to avoid the slew of "Hold power and press home!" comments and the followups telling me to hold it longer, hold volume, and all of the other normally recommended fixes. I know how to write a bug ticket or two. I'm also the type of guy who posts a followup with what actually fixes the problem (No "nm, fixed it" from me).
It sounds like my current plan of action is going to mimic what you did. I originally thought the Touchpad was getting no power, so I kept trying to charge it. Now I am waiting for it to lose all power, so I can repeat the process after the device (hopefully) resets. I'm not sure how long that will take since I cannot actually use the device to drain the battery.
Thanks for the responses. Some replies are better than no replies.
So i had a similar situation and tried everything you had mentioned and all the suggestions in the thread. Nothing. No power, completely dead. I even left it
overnight on the charger... nothing. For sure i thought I bricked it. Then, I read online that someone tried the following:
Press and hold Power + Volume Up and click the card (menu) button a thousand times.
Wow! It worked! The TP is alive! In actuality, it only took about 30-50 times (not a thousand) of pressing the menu button while holding power + volume up.
I then got the white USB icon in the middle of the screen and then pressed and held the power + menu button to reboot.
What I did find interesting though is the battery was almost discharged even after having it on the supplied charger (not touchstone) overnight.
Anyway, hope this resolves your issue as well.
No go with Home + Power, Power + Vol Down, Power + Tapping Home
suremail said:
No go with Home + Power, Power + Vol Down, Power + clicking Home
Click to expand...
Click to collapse
Just making sure you read it right since you didn't list it above.
Power + volume up + clicking home button repeatedly.
All 3, same time. Just trying to help.
^ worked for me..thanks
Sent from my HTC Inspire 4G using XDA App
Well this is a really strange one...
Touchpad was completely non-responsive, I'd tried everything above about 5 times and it just wasn't showing any signs of life. I have left it charging all day today.
Assuming it was completely dead, I sat it down. 5 minutes later, it inexplicably just started booting up.
Wish I knew what I did, if anything to make it boot.
I am having the same issue but what got me there was trying to restore my Touchpad via WebOs Dr. It would restore to like 60% or 80% and then say we were unable to reset your device. It kept failing and no ROM was on my the device anymore. When I hold Power+Vol Up+ Home I can hear my PC detect it but that is all it does.
When I get home tonight I am going to try some of the things in this thread.
But what if I cannot get it into recovery? I read that it is near impossible to brick a Touchpad. How can I still recover without getting into recovery?
http://forum.xda-developers.com/showthread.php?t=1394061
Phillip Fry said:
I am having the same issue but what got me there was trying to restore my Touchpad via WebOs Dr. It would restore to like 60% or 80% and then say we were unable to reset your device. It kept failing and no ROM was on my the device anymore. When I hold Power+Vol Up+ Home I can hear my PC detect it but that is all it does.
When I get home tonight I am going to try some of the things in this thread.
But what if I cannot get it into recovery? I read that it is near impossible to brick a Touchpad. How can I still recover without getting into recovery?
http://forum.xda-developers.com/showthread.php?t=1394061
Click to expand...
Click to collapse
not near impossible. I actually bricked mine and had to send it back for RMA.
it got to the point where the hp screen will show, and webos doctor will detect it, but it'll fail when trying to reinstall at about the same percentage as you (maybe less).
menting said:
not near impossible. I actually bricked mine and had to send it back for RMA.
it got to the point where the hp screen will show, and webos doctor will detect it, but it'll fail when trying to reinstall at about the same percentage as you (maybe less).
Click to expand...
Click to collapse
Well I installed Android uninstalled it. Then installed it again and forgot mboot then uninstalled it. So I belive I am back to stock but I wanted to upgrade to 3.0.4 then install Alpha 3.5 as I has having problems with the Touchpad rebooting in both Android and WebOS.
So when do I know if it is bricked. And what do I say to customer support to get it fixed? I just bought the Referbed ones off ebay the other day.
Here's an update...
No luck with anything so far. I caved and decided to take the Touchpad apart to disconnect the battery. I did this and still no screen response. The only changes have been it's a bit more difficult to get it into Palm mode (if it does at all), and now it seems that I can get into QHUSB mode just by repeatedly pressing the vol- button (no need to hold anything else). I do not know if the QHUSB thing was like that before disassembly, or if it is a result of me mucking around.
Unless anyone has any great ideas it looks like I will have to hope HP fixes it in order to tell me it is out of warranty for having Android.
If you send it to Hp and If they can't power it on, I'd say they would definitely replace it. Problem is, I doubt they have any more TP's in stock. Not sure how the warranty would work now being that its a discontinued product.
Hopefully after toying with it enough you'll figure it out and get it powered.
Mine is stuck in download mode too. Still no success.
Here's my experience so far.
Black screen.
When connected to PC :
Home + Vol UP - Device Manager shows PALM (with yellow exclamation) - no driver found.
Vol Down (no need to press home or power) - Device Manager shows QHSUSB_DLOAD (with yellow exclamation) - no driver found.
WebOS Doctor fails to detect device (palm ! in device manager)
I tried forcing novacom drivers on the Palm device (both novacom and novacom-bootie) and then running WebOS Doctor, still refuses to enable next button.
Tried connecting with novaterm, cannot find device. (both novacom and bootie driver).
Power + Home for 15 - 20 secs always resets and clears device from device manager.
I installed QHSUSB Drivers.
now when I Vol Down it installs as a com port (Qualcomm HS-USB QDLoader 9008).
I installed QPST_2.7.323 and am able to see the device as Q/QPC-XXX - ESN=*Download* - Phone Number=*Download* - Banner=*Download*.
I tried resetting the device with QPST, fails to complete the command.
I think I need a new boot.hex to flash to the TP, or a way to force it to charge (if that is the problem).
My Touchpad was low on power when I put it away in the car while on a road trip. I plugged it in to the wall the next day when it wouldn't turn on. After charging overnight, it still refused to power on. That's when I started combing the web for possible solutions.
Please stop posting irrational solutions, such as Power + tap home 5,000,000 times as the few times this did work for others, it was merely coincidence, and power + home would have worked also.
Any rational solutions are welcome.
I may just send it in for warranty. Although I bet that at HP, they will just hook it up to a machine with "special" drivers and re-flash it with Web-OS. I wish they would just let me do the repair myself with the appropriate files.
Who knows, maybe it is a hardware issue, but I doubt it.
I'm having the same problems too. What happened on mine is that my webOS was crashing doing random things like watching videos so I figured I'd just reflash the whole thing. I rebooted and went into the webOS recovery and that's when I think I bricked it. All I got was a USB cable symbol and the touchpad was unresponsive. I couldn't make it do anything and I tried all the appropriate button holding combinations and so I let the power run out over night.
Now when I plug it into the wall all I get is a low battery charging symbol. If I hold the home+power button down the screen will turn off after about 20-30 seconds of holding it down. But when I try to boot into recovery by holding the power+volume up buttons, all I get is the same low battery charging symbol. I'll add that I have had it charging for most of the morning so I don't think it is low battery still. And when I unplug it from the wall I get a symbol of two pronged plug that shows for about 5 seconds and then disappears.
Now when I plug it into the computer, I get the low battery charging symbol for a quick second and then it flashes to the message telling me "To reliably charge, use the cable and power adapter that came with your device" in 5 different languages. When I run webOS doctor I get to the screen where you connect your phone to the usb but it doesn't recognize anything and doesn't let me click next. I was able to have my computer recognize the power+volumedown button as the weird Qhusab thing but my computer said it couldn't find any drivers for it. Now I am not able to reproduce that.
I'm not sure what else to try so if anyone has any suggestions, that would be great. Otherwise I'm going to have to try my luck with HP support.
skiinginstead said:
I'm having the same problems too. What happened on mine is that my webOS was crashing doing random things like watching videos so I figured I'd just reflash the whole thing. I rebooted and went into the webOS recovery and that's when I think I bricked it. All I got was a USB cable symbol and the touchpad was unresponsive. I couldn't make it do anything and I tried all the appropriate button holding combinations and so I let the power run out over night.
Now when I plug it into the wall all I get is a low battery charging symbol. If I hold the home+power button down the screen will turn off after about 20-30 seconds of holding it down. But when I try to boot into recovery by holding the power+volume up buttons, all I get is the same low battery charging symbol. I'll add that I have had it charging for most of the morning so I don't think it is low battery still. And when I unplug it from the wall I get a symbol of two pronged plug that shows for about 5 seconds and then disappears.
Now when I plug it into the computer, I get the low battery charging symbol for a quick second and then it flashes to the message telling me "To reliably charge, use the cable and power adapter that came with your device" in 5 different languages. When I run webOS doctor I get to the screen where you connect your phone to the usb but it doesn't recognize anything and doesn't let me click next. I was able to have my computer recognize the power+volumedown button as the weird Qhusab thing but my computer said it couldn't find any drivers for it. Now I am not able to reproduce that.
I'm not sure what else to try so if anyone has any suggestions, that would be great. Otherwise I'm going to have to try my luck with HP support.
Click to expand...
Click to collapse
Having the EXACT same problem....anyone have any solutions to this? WHy is this happening?
It's a long shot, but it might help if you are getting to the USB symbol on the Touchpad .
I spent hours trying to connect with no luck with the Touch pad in that state. I rebooted my PC and it connected to the TP right away. (I was using a Win 7 64 bit PC.)
Hey guys, here's what's wrong.
I was running the latest version of MIUI and found it to be annoyingly buggy, so I installed Cyanogen from ClockworkMod and start installing it. It ended up hanging halfway through and wouldn't progress. I made what was probably a dumb decision and decided to turn it off since it seemed to have frozen.
Now...it won't turn on. If I connect a wall charger or USB cable, the symbol of an empty battery with the white loading circle comes up for about five seconds, but the circle is not rotating and the screen goes black. This repeats nonstop.
Holding down vol down + home + power to get it into Download mode fails, it just says LOW BATTERY CAN'T DOWNLOAD in red letters. Doing the same with the volume button up gets nothing. I've tried leaving it to charge for two days with no results.
I bought a USB jig and tried using it (removing battery and SIM card, putting battery back in, plugging jig in) but it does nothing. I've tried several times.
Any advice? Is it just dead?
try an external charger to charge your battery or borrow someones battery to test your phone. failing that, charge your battery in someone else's phone.
Was the battery full when you tried installing cyanogen mod, and did you follow the instructions fully?
Clean the battery contacts on both the battery and phone pins. Use another charger, and check the port for blockages/dirt (blow in it).
Try another battery..
-Leave the jig in for 30 mins.
-Hold the combo and then put the battery in whilst holding the combo.
-Plug into your computer (with battery) and try the combo. Then try without, and put battery in whilst connected and whilst holding.
-Hold combo then plug into computer
Some of the methods above may require some extreme skill or a helping hand
It could be water damage.
I don't think it is bricked as i don't think those messages would be showing up, but i could be wrong.
If none of that works and no-one else comes up with any other ideas then you may have to use the unbrickable mod. Search for it, it's a hardware hack..
Good luck
Hello everyone,
I installed a JB rom a few weeks ago on my TP (can't remember which one)...it worked for a little while, then i wanted to flash something additional and it seems to be bricked ever since and has been laying around...which is why I can't remember what exactly I wanted to flash
Anywho, if i connect it to the PC the notification LED on the home button is blinking..but that's it. no combination of power/voldownup/home button seems to be working and when I try to run webos doctor it doesn't recognise my device.
can anyone please help me?
When you say bricked. Do you mean stuck in a boot loop wouldn't turn on etc.
Have you had it connected to the stock charger or better still on a touchstone and if so for how long.
The more information you can give the better.
No it doesn't turn on at all, screen stays black.
It's been connected to what i think is the stock cable to my pc (there are too many Micro-USB cables laying around here ) for about an hour now and i just put it on the touchstone (LEDs are still flashing)..
Leave on the Touchstone for at least a few hours preferably overnight then hold the power and volume up buttons for at least 30 seconds if nothing happens do the same with power and home buttons and post any progress or lack of, but the first thing is to try and put some charge into it and the best for that imo is the Touchstone.
maxiv said:
No it doesn't turn on at all, screen stays black.
It's been connected to what i think is the stock cable to my pc (there are too many Micro-USB cables laying around here ) for about an hour now and i just put it on the touchstone (LEDs are still flashing)..
Click to expand...
Click to collapse
The stock cable for the touchpad has a silver dot at each end. I have two touchpads ad the connection is very loose and unreliable. It often won't charge. I bought new Micro USB charge/sync cables and charging is no longer an issue.
The USB port on your computer is not powerful enough for anything it trickle charge. You need a stock touchpad charger.
Well i charged on the touchstone and then after a few hours i was able to boot into recovery and flash a new rom problem solved, thanks anyway!
I had over 80 percent in battery and now my phone wont charge or turn on or even be in fastboot mode... please help
miguel11691 said:
I had over 80 percent in battery and now my phone wont charge or turn on or even be in fastboot mode... please help
Click to expand...
Click to collapse
Did you get this to work?
Based on your post count, this is probably a stupid question but:
You tried charging in an outlet (not through computer), right? Any under-the-hood work makes my Bionic run hot and burn through the battery.
More technical: I read somewhere that someone upgraded to windows 8 and fastboot stopped working. Windows 7 fixed the problem (if you're saying that fastboot is the problem, not Vol - & power button recovery mode).
Were you in the process of rooting?
LJ6782 said:
Did you get this to work?
Based on your post count, this is probably a stupid question but:
You tried charging in an outlet (not through computer), right? Any under-the-hood work makes my Bionic run hot and burn through the battery.
More technical: I read somewhere that someone upgraded to windows 8 and fastboot stopped working. Windows 7 fixed the problem (if you're saying that fastboot is the problem, not Vol - & power button recovery mode).
Were you in the process of rooting?
Click to expand...
Click to collapse
I am kind of having the same problem. I recenty got a droid bionic where I had to replace the LCD screen and battery since when I got it it did not have a battery with it. I got an NON-OEM extended battery and every thing was working fine for three days. In that time I was able to upgrade everyting to the latest software, fireware, and Android version (4.1.2 JB) but after those three days the phoe woould not power on. When I plugged it into my computer and tried, the white power light would just blink at me. when I unplugged it from the computer and tried it would not even come on. I thought it was the battery so I sent it back and got an OEM extended batter and a OEM dock/charger. When I got everything I plugged it all in and the screen came on with the Motorola M logo and then showed me a picture of the battery at 5%, so I let it charger over night. In the morning I pressed the power button while still plugged into the charger, the phone light up saying the battery was at 100%. So I took it off the charger and tried to power up. Nothing happened. I plugged it into my computer and the white power light came on and stayed solid but still no power-up. I just tries the Volume Up/Down power while plugged into the wall charger and I can get to the recovery screen and try the normal boot up, I get the Motorola M Logo screen, I just now tried recovery and the little Droid just showed up with its stomach with a red triangle and an ! in it and is just sittin there. and now it when back to the Motorola M Logo screen then the battery screen. Does this mean mine is bricked as well? Please some one help.
Bumping because of no help yet. I can access the recovery screen but does not seem to help any, it also has to be plugged into the wall charger for this to happen but I can not power it up whether it is plugged in or not. Please Help someone so I can get this figures out.
Alright strange thing to try, plug it into your computer, while plugged in take it the battery, give it a minute and put it back in while still plugged in.
Sent from my XT875 using Tapatalk 2
Did as you suggest but when I took out the battery. the white light stayed on. Still could do nothing. Waited 2 minutes, put the battery back in and still nothing. All I get is the white light staying on. I unplug from the computer, the light turns off and still nothing, not even the recovery screen will boot up.
Can you get to the fast boot option by holding both volume buttons and power
Sent from my XT875 using Tapatalk 2
B.E.McAllister said:
Can you get to the fast boot option by holding both volume buttons and power
Sent from my XT875 using Tapatalk 2
Click to expand...
Click to collapse
As long as I keep it plugged into the wall charger I can. When I go there it says "Battery Low Cannot Program Connect USB Data Cable. But as soon as I unplug the wall charger it shuts off and I can not get back to fast boot. When I plug it into the USB cable and plug into the computer, I can not get to fast boot. I just check and it says my battery is at 100%. but when I first plug it in it says 5%.
Your gonna need to charge your battery with either an external charger or the usb charging hack before you can perform an fxz on it
Sent from my XT875 using Tapatalk 2
hey guy's i haven't played around with my touchpad in over 4 months...recently i have tried turning it on and it was completely dead...so i plugged it in for like 3 days..still nothing..
so im reading in different threads that it seems common when the battery dies completely...
so i have tried all the volume up power tap the menu....volume down...
i plugged it to my pc and tryed the volume up trick.he pc seems to recognize it in the device manager..see on pic.
so whats the next step?is the an app to install on pc like odin??
Does the device even attempt to power up? Or is there no on screen activity whatsoever?
Sent from my Nexus 10 using Tapatalk 4
Izeltokatl said:
Does the device even attempt to power up? Or is there no on screen activity whatsoever?
Sent from my Nexus 10 using Tapatalk 4
Click to expand...
Click to collapse
i got it going with the ubuntu tutorial.seems like there was a file that was corrupt..
then i tried to upgrade the cm9 to 10 with no success..no the tablet boots to webos direct no more dual boot screen.,,,,
but it's ok i gave it to my mom..she is fine with webos..for emails and facebook...lol
but odd...
delete reply, since the OP is able to boot with webos.
techker said:
i got it going with the ubuntu tutorial.seems like there was a file that was corrupt..
then i tried to upgrade the cm9 to 10 with no success..no the tablet boots to webos direct no more dual boot screen.,,,,
but it's ok i gave it to my mom..she is fine with webos..for emails and facebook...lol
but odd...
Click to expand...
Click to collapse
can u pm me what u used to get it working thanks
Unplug your tablet, then hold in Power + Vol Down + Menu. After 10 or so second the Touchpad should turn on and show the AC plug. Plug it into the AC charger and let it charge. If the Touchpad was completely dead and didn't have any charge whatsoever (you say that you've been charging for 3 days), you would want to charge it for a few hours first. It charges extremely slow in a powered-off state and likely won't get much more power than is required to boot into the low battery mode even after 3 days of charging while off.
source: my Touchpad has done this many times
scy1192 said:
Unplug your tablet, then hold in Power + Vol Down + Menu. After 10 or so second the Touchpad should turn on and show the AC plug. Plug it into the AC charger and let it charge. If the Touchpad was completely dead and didn't have any charge whatsoever (you say that you've been charging for 3 days), you would want to charge it for a few hours first. It charges extremely slow in a powered-off state and likely won't get much more power than is required to boot into the low battery mode even after 3 days of charging while off.
source: my Touchpad has done this many times
Click to expand...
Click to collapse
this is what saved it!
http://rootzwiki.com/topic/38786-tpdebrick-v004/
tpdebrick!