Installed cyanogenmod 9 and bricked. - Captivate Q&A, Help & Troubleshooting

So, the phone worked well with CM9 for a while. Then the guy that owned the device attempted to update it, I'm not sure what went wrong but the fact of the matter is that it kept bootlooping on the CM9 splash screen. Entering into recovery was unresponsive and doing the three button combo to enter into Download Mode was unresponsive.
I followed a guide on here on how to make on my own jig. I successfully made the jig and I am able to enter into Download mode now. However, I am unsure what to do from here. I attempted to use Odin and flash a Corn kernel for the captivate, thinking I'd be able to boot into recovery and then flash a rom from that point. Unfortunately, I am unable to do this. Nothing boots up except the ATT screen now. Maybe there is a failsafe way in getting the phone back to working order?
Any advice would be appreciated.

Have you tried pulling the battery, holding down both volume buttons, and plugging the USB cable in to enter download mode? Once there, try flashing it back to the original state with Odin One-Click or similar. I have bricked and unbricked my phone at least twice, and each time was able to get it to recover by using this method. Hope it works for you. Good luck!

Thanks, it worked. I think I'm on Froyo now, but at least its working. I originally downloaded Odin-one Click but didn't recognize the interface. Thanks!

Related

I know,Another Bricked Phone...sigh

I had loaded the ginger clone rom and all was well. I then however wanted to swap kernels so i loaded up seitrons cwm 1.5.6 and proceeded to flash through cwm. this has now become the worst day of my life. the phone will not boot past the galaxy s screen. i cannot not get into recovery and both computers now say usb device not recognized when in download trying to flash odin. i am worried that something is corrupted on my phone because not matter how many times i uninstall and reinstall the drivers no luck. i think it is officially bricked and im sol. maybe some great minds can figure it out here.
It's not bricked - issue is trying to get your computer to recognize your phone when in download mode so you can flash it back.
What OS are you running? Also - where did you download the drivers from? Some seem to work better than others.
If you can get to the galaxy screen you might still be able to to get into recovery. pull out the battery and use the 3 button combo. Hold down both volume button then power and let go of the power button after it turns on. then just reinstall the rom
I'm willing to bet you can also get into Download Mode either with button combos, or a JIG. Once in Download, you can use Odin to restore to JF6, and have a working phone to flash around with again.
i can get into download mode no problem. and i think it is quite possible drivers are corrupted on the phone itself. my wifes phone works on the same exact setup. no usb device not recognized error. i have tried the drivers from here and samsung directly with no luck. 3 button combo does not work. sim out sim in battery out and in. but like i said it will just not register with the comp and hers will. so im going to att and seeing about replacing it. but i will see how that goes. ive done this lots of times with no issues ever.
download works
3 button combo does not so no recovery
usb device not recognized error
thanks for the help and keep it coming i will try everything if i haven't already.
Try current usb port
Sent from my SCH-I897 using XDA App
Think I'm in worse shape. Tried flashing just the kernel to get BLN working again (last ROM I put on somehow loaded a non-compatible kernel). Now the phone boots the white ATT screen and just sits there. Can't get it into D/L mode with 3-button and doesn't respond to computer I have been using to flash ROMs for a couple weeks now...
Am I hosed? ANY help would be greatly appreciated...
You could try to use a JIG to force your phone into Download Mode
Okay...well, got into D/L mode finally. Used Odin to get it back to factory. Used the One Click rooter again, except now it boots to recovery 3e, which doesn't let my power button work as the okay button Pulling the battery to reset it, but it will no longer go into D/L mode to use Odin again. It keeps booting to the recovery Utils, which I cant get out of...*sigh*
Thoughts?
at least your able to do something i still cannot get my phone into recovery or to be recognized by the computer. it is not the drivers so i have no idea. i can only think that something got funked up with the kernel flash.
if you are getting into 3e recovery then you are most certainly NOT using the JF6 one click stock
3e recovery comes on JI6 which is the FroYo leak....completely different builds and roms
have you tried a different usb cable? I was having this problem, and the stock samsung cable was B.O. and wasnt working... i tried my blackberry one and all was good
magnumrt562 said:
have you tried a different usb cable? I was having this problem, and the stock samsung cable was B.O. and wasnt working... i tried my blackberry one and all was good
Click to expand...
Click to collapse
i actually tried this yes. i had a blackberry cable from the storm (shivers) that was laying around. tried that but no luck with that or my wifes cable as well. but a good tip for others nonetheless
Pirateghost said:
if you are getting into 3e recovery then you are most certainly NOT using the JF6 one click stock
3e recovery comes on JI6 which is the FroYo leak....completely different builds and roms
Click to expand...
Click to collapse
I just want to quote this to stress the importance.
Thank you, didn't realize that (still sorta new to this)...
I downloaded a zip (I thought from here somewhere) that extracted into the 4 files. Anyone got a link to the JH6 set of files?
I also downloaded DG's "One Click Odin", but it doesn't seem to really do anything when I run it unless I manually load all the files. Also, I don't see a "Master Clean" like the post refer too
are you sure you downloaded the right odin? in the one click version, theres no option to load files at all. only a "start" and "master clear"
make sure the odin one click is open before you connect your phone.
http://forum.xda-developers.com/showthread.php?t=731989
You guys rock! I don't know how, cause I could have sworn I D/L'd it from that link before and I got the generic Odin, but it looks like I have the right one now! Thank you for your patience with us noobs as we start getting into this new world!
glad you got yours working. i have officially given up and receiving a new one on tuesday. i tried everything but somehow someway the phone is not recognized in download mode. oh well have to mess the with new one then lol
zippox180 said:
glad you got yours working. i have officially given up and receiving a new one on tuesday. i tried everything but somehow someway the phone is not recognized in download mode. oh well have to mess the with new one then lol
Click to expand...
Click to collapse
I was having the same problem. Have you tried powering off, start odin, hold both the volume up/down, then plug in the usb to your phone?

Interesting Problem with Cappy

I've Had my cappy for something over a year and up until i finally got a working jig it was out of commision for about a month, Then all was saved with the jig and i reflashed stock and started from scratch trying new roms, Then, when trying to go from stock to apex using their own odin flashers, Then when it went back into recovery i hit reboot to begin using CWM. Then all of a sudden, The Gingerbread version of the softbrick screen comes up, Phone----!-----Computer. No worries i have my jig, then when i remove the battery, wait and put the jig back in . . . the phone just shows me a bricked screen again, with a jig i know worked. What have i done?
SnowBlind182 said:
I've Had my cappy for something over a year and up until i finally got a working jig it was out of commision for about a month, Then all was saved with the jig and i reflashed stock and started from scratch trying new roms, Then, when trying to go from stock to apex using their own odin flashers, Then when it went back into recovery i hit reboot to begin using CWM. Then all of a sudden, The Gingerbread version of the softbrick screen comes up, Phone----!-----Computer. No worries i have my jig, then when i remove the battery, wait and put the jig back in . . . the phone just shows me a bricked screen again, with a jig i know worked. What have i done?
Click to expand...
Click to collapse
If by "bricked screen" you mean the Phone--!--Computer screen, you should be able flash back from that screen. In theory, ODIN should recognize your phone at that screen in a manner similar to the way it recognizes it at the normal download mode screen.
As long as you see the computer/phone symbol you should be able to get it reflashed with the J6 Oneclick. If it never appears in ODIN try all of your USB ports. Odin only sees my phone on the two rear ports, go figure.
As far as getting the yellow download screen goes you might consider some other key combos before you declare it non-functioning. Did you flash it back to stock J6? If so, did the 3-button stop working? That may be your issue. Also, you may have put boot loaders on it from another device such as an I9000 and changed the key combo while flashing another ROM. Try battery pull/replace with vol up and USB, vol down and usb, both up/down with USB and see if any of those work.

[Q] Stuck in boot screen

I was running CM7 nightly builds. I was attempting to switch to the stable CM7 build with an ODIN restore. I couldn't get ODIN to recognize my phone, and a forum thread said to try re-installing the update.zip file from the recovery boot. It got hung up trying to do that and upon reboot, it is now stuck on the startup screen. Can't get to recovery, can't do anything. Any thoughts?
Help is GREATLY appreciated.
Thanks!
have you pulled battery and started again? tried button combos? have you used odin since installing cm7? i believe it needs different drivers..... more info will get you more help. more reading will keep you out of trouble (mostly) i've never used cm7 so i can't help that much...
I have tried pulling the battery, running the battery to dead and then putting it on the charger, all the button combos.
I have not tried ODIN but thats because ODIN needs to be in download mode and I cant get into download mode. The only thing I can get to is the AT&T World Phone screen with the white background. I have done some google searching about getting stuck on the boot screen but none of the threads I have found have seemed to mot relate to my exact problem. I am currently looking into if this is the kind of problem that a jig would fix.
definitely sounds like a job for a jig.. it will force it into d/l mode as long as the bootloaders are not corrupted..... best of luck
if the bootloaders are corrupted, is there anything to do or is the phone just finished?
Jtag/unbrickable mod
I had the same loop yesterday doing something else, but i had the ATT boot loop and no button combos worked to get into DL mode. So I tried pulling the battery, then holding vol+/vol-, putting battery back in, and then plugging in usb cable. Went to DL mode. If that doesn't work, I'm sure a jig would.
fuloplori said:
Jtag/unbrickable mod
Click to expand...
Click to collapse
Jtag should only be used for hard bricked phones. Since there is a sign of life, he can probably recover from this without the need of jtag.
Use a jig. It's the easiest way to get into dl mode. If you don't have one, you can make a crude one that will work until you can get a proper one ordered.
beast534 said:
I had the same loop yesterday doing something else, but i had the ATT boot loop and no button combos worked to get into DL mode. So I tried pulling the battery, then holding vol+/vol-, putting battery back in, and then plugging in usb cable. Went to DL mode. If that doesn't work, I'm sure a jig would.
Click to expand...
Click to collapse
That got it into download mode! I am going to try and ODIN restore and see what happens. Thanks!
ODIN Restore worked! I had to restart it a couple of times but I am back on stock. Now to get the stable CM7 becuase I don't think I can handle stock ROM again...
cdenney said:
ODIN Restore worked! I had to restart it a couple of times but I am back on stock. Now to get the stable CM7 becuase I don't think I can handle stock ROM again...
Click to expand...
Click to collapse
Great! Glad I could help

[Q] Bricked phone? flashed SlimICS through Clockwork

hey all, i've had my captivate for about two years now, and for a while i used cognition, then for the last year i've been using firefly. firefly has completely destroyed my phone's speed and responsiveness, and i needed to clean everything off and start with a minimalist ROM. so i picked slimICS.
i'm still very hazy on the details and terminology of flashing ROMs, but i got two to work (i remember using one-click root thing in 2010, and then in 2011 i flashed firefly through clockwork) so i figured it shouldn't be a problem to install slim, which i figured would be my last ROM until next year, when i'd get a new phone.
so i backed up my stuff, tried to get into recovery mode with the 3 buttons (didn't work, unsurprising since it didn't work last year either), took out my SIM, went to CWM, and selected the flash rom option. this restarted the phone and sent it into recovery mode--except it was the stock recovery, and i couldn't select anything because i think firefly made the phone think it was the i9000 model from canada, instead of the i897 captivate, so it assumed i had a physical "ok" button on my phone (which i obviously do not). i tried the power button, the various capacitive buttons on the bottom, nothing would select any of the options, so i just took out the battery and put it back in. the phone immediately booted into the CWM recovery menu, in which i selected flash ROM, and scrolled down to choose slimICS.
i let it do its thing for a while, it jumped between the AT&T white logo screen and a screen with scrolling text for like 5-10 minutes, then just stayed on the AT&T logo screen for another ten minutes. i should have left it for maybe a half hour to be sure, but i figured the install failed. i couldn't get out of this so i pulled the batttery. and now the phone is bricked (soft i hope). if i hold the power button it goes to the AT&T white logo, flashes briefly for a half-second and goes back to the screen, then stays there indefinitely. no button combinations seem to work. does anyone have any suggestions?
thanks!
Since you backed everything up, I'd suggest flashing a stock rom via Odin or Heimdall to clean everything up before moving forwards.
You can flash a non-bootloader one to be safe, or if you want to make sure you can flash anything, flash a package with Gingerbread bootloaders.
jmtheiss said:
Since you backed everything up, I'd suggest flashing a stock rom via Odin or Heimdall to clean everything up before moving forwards.
You can flash a non-bootloader one to be safe, or if you want to make sure you can flash anything, flash a package with Gingerbread bootloaders.
Click to expand...
Click to collapse
how do i flash anything in my phone's current condition? it doesn't turn on fully. it's stuck at the white AT&T logo.
Turn it completely off (pull the battery, if necessary), then hold V+ and V-, and insert a USB cable. That should put it in download mode. Once you're there, you can flash a stock rom (There's a stick with those roms in the development section).
jmtheiss said:
Turn it completely off (pull the battery, if necessary), then hold V+ and V-, and insert a USB cable. That should put it in download mode. Once you're there, you can flash a stock rom (There's a stick with those roms in the development section).
Click to expand...
Click to collapse
doesn't work. as i mentioned in the OP, i can't get into download or recovery mode or whatever. these button combos have never ever worked with this phone. for example, holding + and - and inserting a cable with ODIN open has never done anything. that's why i used clockwork.
Sounds like u r gonna need a Jig. If u are on a pc, click on my sig link below and there u will find a link on how to make a jig and/or where to buy one.
4-2ndtwin said:
Sounds like u r gonna need a Jig. If u are on a pc, click on my sig link below and there u will find a link on how to make a jig and/or where to buy one.
Click to expand...
Click to collapse
is that guaranteed to work? or is it most likely? or is it unlikely at this point?
The jigs that I have made myself in the past and as well the professional made ones that I have purchased have always worked to get me into download mode.
The jig is worth a try, I suggest you should
if I'm reading the op right, and if memory serves firefly was an I9000 build and button combos are different. My suggestion would get the Odin kk4 one click with repartition and WITH boot loaders from 4-2ndtwin's sig links, open that and while powered off and holding just the vol- button insert the USB that should do the trick. I9000 builds use different boot loaders with different button combos. Since you will be flashing a boot loader package be aware this is when you can truly hard brick your device. Be sure you have a good connection and cable before starting. If you still can't get into download mode I can +1 on the jig. The jig and 4-2ndtwins one click has saved my bacon more than once.
ok so i bought the jig, and good news: it gets me into download mode! yay!
problem: i don't know where to go from here. i've tried the following:
A. after getting into download mode, i followed the ODIN method here: http://forum.xda-developers.com/showthread.php?t=1350266, meaning i flashed the gingerbread bootloader update (nothing happened to the phone, which made me confused when i got to step 7., because i was STILL IN download mode), then flashed the speedmod kernel (which reset the phone, but it just got stuck in the "SAMSUNG CAPTIVATE i-897" white text on black screen, forever. i had to do a battery pull. turning on the phone goes to the same screen and then it freezes. trying to hold all three buttons to go into recovery mode alternates between that screen and the white AT&T screen, actually alternates, forever if i let it.
B. after that failed, i tried using the 2.2 Heimdall one-click (http://forum.xda-developers.com/showthread.php?t=1266172) but the file, when run, says
Code:
ERROR: Drivers Not Found
Installing drivers
but i still followed the instructions (except the instructions say "Install driver" but the actual button is "Replace driver"?) in any case, this does nothing. and then checking off "Flash bootloaders" and doing it again does nothing. the phone remains in download mode.
C. so i wanted to try one-click downloader http://forum.xda-developers.com/showthread.php?t=731989, but nothing pops up on the ODIN window when i plug my phone in. i can't even do anything.
please help!
please, does nobody know what to do?
Take a look at the "Captivate Connection Issues" thread for some more things to try. At this point, it sounds like you need to clear all the phone drivers off of your machine and reinstall them.
jmtheiss said:
Take a look at the "Captivate Connection Issues" thread for some more things to try. At this point, it sounds like you need to clear all the phone drivers off of your machine and reinstall them.
Click to expand...
Click to collapse
thanks, that worked! (it was my laptop that was the source of the connection issues i think; i tried all that stuff in the thread, but when i switched to the desktop, all of a sudden ODIN recognizes the phone!) i got my phone to flash ODIN one-click. so now i'm back to stock 2.1 eclair.
however, much to my dismay, i still can't get into recovery mode to (re-) root. the three button combo still does the weird flashing thing, where the white AT&T logo shows up, then the screen goes to black, then the AT&T logo, then black... ad infinitum. how do i either 1) enter recovery, or 2) re-root the phone + get a nice, lean, fast, modern ROM on it without going into recovery?
so far this thread has helped me unbrick the phone, now all i need is to update it from stock!
spacenegroes said:
thanks, that worked! (it was my laptop that was the source of the connection issues i think; i tried all that stuff in the thread, but when i switched to the desktop, all of a sudden ODIN recognizes the phone!) i got my phone to flash ODIN one-click. so now i'm back to stock 2.1 eclair.
however, much to my dismay, i still can't get into recovery mode to (re-) root. the three button combo still does the weird flashing thing, where the white AT&T logo shows up, then the screen goes to black, then the AT&T logo, then black... ad infinitum. how do i either 1) enter recovery, or 2) re-root the phone + get a nice, lean, fast, modern ROM on it without going into recovery?
so far this thread has helped me unbrick the phone, now all i need is to update it from stock!
Click to expand...
Click to collapse
I could be wrong but when you do the 3 button combo it sounds like you are continually holding the buttons which will cause it to keep looping like you describe. Starting with your phone off hold down all three buttons. The phone will show the white ATT screen. Then if you had a custom kernel it would show the kernel splash screen, in your case you said it just goes black which is fine too. Then you will of course get the white ATT screen again. As soon as you see the white ATT screen again release all the buttons and that should boot it into recovery.
m1batt1 said:
I could be wrong but when you do the 3 button combo it sounds like you are continually holding the buttons which will cause it to keep looping like you describe. Starting with your phone off hold down all three buttons. The phone will show the white ATT screen. Then if you had a custom kernel it would show the kernel splash screen, in your case you said it just goes black which is fine too. Then you will of course get the white ATT screen again. As soon as you see the white ATT screen again release all the buttons and that should boot it into recovery.
Click to expand...
Click to collapse
i tried various durations of holding the buttons. none worked. 2nd AT&T logo, nope. 1st black screen, nope. 1st AT&T logo, nope.
Your gonna have to get ADB set up on your pc. Then... "adb reboot recovery" will get u into recovery mode.
Sent from my SGH-I897 using xda premium

[Q] Captivate ROM Error

Ok, so I hard bricked my Captivate, used the Radioshack homemade jig to force it into download mode, and flashed Gingerbread 2.3.6 XXJVU. After further research, I realized I wanted to downgrade to 2.3 for a more effective custom ROM flash, so I flashed a stock Eclair 2.1 ROM using Odin one click (with bootloaders, I'm assuming). The flash was successful as far as Odin was concerned, but now the phone gets stuck in a boot loop for quite some time. If I let the loop run its course, it will eventually load the 2.1 ROM, but the phone will power off after about 5 seconds after I plug either a USB cable OR a charger (the charger is recognized as a USB cord by the phone). I cannot get the phone into recovery or download mode; the 10 plus button combinations do not work, and the jig sends it into the boot loop. I even tried holding the volume down key through the entire boot loop sequence, but it never stops (as opposed to not holding the volume down key, where it boots eventually). I tried reformatting the internal SD card, and I looked into putting it into download mode through ADB, but I do not have it installed and even if I did, I can't get the phone to stay on while connected via USB. The computer even recognizes it through USB until the phone shuts off. Through much research, I've come to the conclusion that I must re-brick my phone somehow from within the stock ROM I have installed. I have no idea if this is even possible or if it's the right solution, but I'm at the end of the line at this point. Any suggestions to help with this?
worldextermination said:
After further research, I realized I wanted to downgrade to 2.3 for a more effective custom ROM flash, so I flashed a stock Eclair 2.1 ROM using Odin one click (with bootloaders, I'm assuming).
Click to expand...
Click to collapse
No such thing as "more effective custom ROM flash". All you need is stock GB with GB bootloaders.
You need to get to Download mode and flash stock GB. Tons of information in this forum, please read it.
I've been browsing these forums for days for information on this subject, and none of the solutions I've found fix my problem.
And where exactly did you read you need to downgrade 2.3.x to 2.1 in order to flash a custom ROM?
Calm down, turn the phone off and leave it on a charger for few hours in order to recharge the battery. Disconnect the charger, remove the battery, remove SIM and SD. Reinstall battery only, hold both volume keys and plug the phone to the PC. See Download mode now?
I didn't read that I needed to downgrade, but the guides I was reading were one click solutions for root and flash for 2.3, and I guess should've ignored them and done it manually. I did a one click on a #1110 phone, which is why it's now acting lame, I assume.
Ha, I am pretty calm. I have a Verizon Galaxy S that I've been using to charge the battery, since my AT&T Captivate won't even charge the battery via USB or straight charger when it's off, so it's pretty full. I've tried every method, including the one you just mentioned, and none of them work to bring me to download mode.
Captivate - PC Connection Issues, Download Mode and Recovery Mode Help
4-2ndtwin said:
Captivate - PC Connection Issues, Download Mode and Recovery Mode Help
Click to expand...
Click to collapse
I've had that thread open in my browser for the past 2 days, and have tried everything it suggests multiple times.
^
Have ya tried to make a Jig ?
http://forum.xda-developers.com/showpost.php?p=9238587&postcount=1
The jig I used to get it from fully bricked state into download mode would put it back into the boot loop. I solved my problem with the adb reboot download command. I managed to activate the command before the phone randomly shut off, as it does when I insert the USB cable. Thanks everyone!

Categories

Resources