I previously mentioned in the Bionic [Request] thread that the steps for making a RAZR work on PagePlus were the same as a Bionic, however, that statement is not entirely accurate. There is no *#*#4636#*#* on a RAZR, and as such, there seems to be no way at the moment to get 3G data. Picture messaging works if you install VZW messages from the market.
Here is what I did:
First and foremost, use the IMEI but drop the last digit. This is your MEID. Call Pageplus, or find a pageplus dealer who is nice enough to activate it for you, and give them this MEID. You will have to call pageplus cs after you are finished with the following programming to get the MEID put back on the phone. I don't know why this is, and I am not going to give you any kind of technical BS to make it look like I do.
1. Put phone into BP Tools mode by powering off, then pressing both up and down volume and power. Volume down to BP Tools and Volume up to choose it.
2. Install the latest Motorola Driver for your phone from: http://developer.motorola.com/docstools/USB_Drivers/
3. Connect the phone to the PC, and let the driver install complete.
4. Run HW Virtual Serial Port, and login with the password "admin" (it is already there by default, so just hit enter).< no longer necessary
5. Set the IP as 192.168.16.2, with the port as 11008.
6. Choose com port 100.
7. Open CDMA-Workshop 3.7 or higher (There is no known copy floating around for free. Either find someone who has it installed already, or pay the $108 like I did... if you're like me, you'll find ways to recoup your money. I have made it back a few times over already.) Choose COM port and click CONNECT.
8. Click on Security, SPC and send 000000. Do this EVERYTIME you reconnect the phone. Everytime. Don't forget this.
9. Click on Main and go down to where it says CDMA and change it to CDMA-2.
10. Under R-UIM change config to NV Only.
11. Click on the "Other" tab. At PRL, choose write and write the pageplus prl (51720 only) to it. Google for this, it's out there. Write to phone.
12. REBOOT the phone.
13. Reconnect and resend SPC.
14. On the MAIN tab, switch CDMA-2 back to CDMA.
15. Write 310 to MCC, 00 to MNC, and your MIN. Leave True IMSI alone.
16. Write 283, 384 to P CH; and 691 and 777 S CH.
17. Write your mobile number to the DIR_Number and DIR_PCS fields. Write to phone.
18. Change CDMA to EDVO.
19. under PPP User and HDR User write your phone number [email protected], with vzw for the password.
20. under Teth. NAI write your number [email protected].
21. Click on m.ip profiles
22. NAI is the same as 19. T NAI is the same as 20. The shared Secret fields are both VZW.
23. If necessary, change the P. HA address to 255.255.255.255.
24. Click X, then write to phone.
25. Disconnect the phone and reboot it. You are done with CDMA workshop.
26. On your phone, under Settings > wireless and networks > mobile networks > network mode change to CDMA only.
27. Connect to wi-fi and download phone in Play Store (Android Market)
28. Open phone info and go to phone information. Scroll down to set preferred network type and change it to CDMA auto (prl) and toggle DNS Check to allowed.
29. ##Program on your dialer, use "000000" for SPC code, and go to 3> Extended NAM and change the SID to whatever your SID is.
30. Back once to 06 Test Mode, next twice, then make sure network mode is CDMA and EVDO
31. Back once and go to 14 LTE Test Settings. Change SIM Type to 3g, LTE bppanic to disable. Back twice to reboot. Remove SIM Card while rebooting.
32. Back to ##Program 14, disable class1 and class2 APNs and back out. Phone will reboot.
That's it. I have 3g working on 173. Haven't gotten it on 181 or on the ICS leak, though, but, I have a droid razr on my prepaid 29.99/month plan, and couldn't be happier.
Any questions? Please message me. I will respond ASAP.
Please remember to hit the Thanks button if this helps you!!
Think this method would work on the Droid 4 (XT894) as well?
Was considering sending one to Beigephone for programming. However I'd like to learn how to do this myself, so when the time comes if I need to reprogram the phone again, I can do it.
I could only assume so. But, I didn't know if the RAZR would work until I tried it for myself.
I have tried following your guide, and I just had a few things to add from my experience.
Between steps 7 and 8, I had to use 'Read' at the top of CDMA Workshop for it to allow me to enter the SPC code. I clicked the top Read, and I got this message:
DM baud rate has been automatically switched from 38400 to 921600
I was then able to input the SPC.
Furthermore, I was unable to read all of the information from the phone. The top Read worked fine, but the one in the Main tab could only pull certain information. Likewise, the Write button could only write some of the information, and was unable to write all the information under the M.IP Profiles section.
I actually was unable to try and complete the flash because the customer had to leave for work, so he ended up selling me the phone, haha. Any idea why CDMA WS kept erroring out halfway through writing the information?
I also have tried undoing everything through factory reset and changing the mode back to R-UIM only so I could sell it for Verizon, but even after changing the R-UIM settings back, the phone keeps saying there's no SIM card =/
that is the hard way. try this link for the easy way. i have done the razr and droid 4 with this method. i started with the bionic and i am sure it will work on the razr maxx. it doesn't cost a thing.
try this (post #25)
http://forum.xda-developers.com/showthread.php?t=1300959&page=3
or even better
http://www.howardforums.com/showthread.php/1752710-Manual-Activation-of-Droid-Bionic-Questions/page4
Instead of creating a Virtual Port. Just boot into BP Tools by pressing the Vol Up and Down buttons from power off. Scroll to BP Tools and press the Vol Up Button. I Used CDMA Workshop. Under CDMA2 Change it to NV Only. Writed a PP PRL. Mine took very easily. 3G was a bit harder but it does work. Most people report that it will only go 1x. After a bit of tweaking it switched to 3G and everything is running perfect.
I have successfully done a RAZR and RAZR MAXX the last 2 days. The process is the same on both.
(Trying to remember, don't have phone in front of me)
Boot up phone with SIM in, remove SIM upon reaching home screen.
##PROGRAM + SEND, enter 000000 for lock code.
Option 6 (Test Mode), hit next until you see Network Mode. Change it to CDMA and EVDO.
Go back to menu, option 14 (LTE Settings), change Sim Type to 3G UICC Test.
Reboot phone.
Go back into ##PROGRAM, option 1 (User Activation) and punch in your correct MIN, MDN and so forth.
There is another option for SMS/MMS settings that I had to change the MML server to [email protected] for text to work. Wasn't able to text MMS because the customer ran out of data
Make sure in your Data Manager under Settings that you have it set to roam for all trips or you won't get any data.
I'd like someone else to try this if they can, being that I sold both my RAZR and RAZR MAXX and I forgot to document the process, haha. If I come across another one, I'll be sure to update this reply.
I had 3G data, voice, text, and I believe MMS was working.
Hope this helps someone!
Ha1cy0n said:
I have successfully done a RAZR and RAZR MAXX the last 2 days. The process is the same on both.
(Trying to remember, don't have phone in front of me)
Boot up phone with SIM in, remove SIM upon reaching home screen.
##PROGRAM + SEND, enter 000000 for lock code.
Option 6 (Test Mode), hit next until you see Network Mode. Change it to CDMA and EVDO.
Go back to menu, option 14 (LTE Settings), change Sim Type to 3G UICC Test.
Reboot phone.
Go back into ##PROGRAM, option 1 (User Activation) and punch in your correct MIN, MDN and so forth.
There is another option for SMS/MMS settings that I had to change the MML server to [email protected] for text to work. Wasn't able to text MMS because the customer ran out of data
Make sure in your Data Manager under Settings that you have it set to roam for all trips or you won't get any data.
I'd like someone else to try this if they can, being that I sold both my RAZR and RAZR MAXX and I forgot to document the process, haha. If I come across another one, I'll be sure to update this reply.
I had 3G data, voice, text, and I believe MMS was working.
Hope this helps someone!
Click to expand...
Click to collapse
when i rebooted and tried to enter the MIN, MDN etc. it said "Failed to get call NAM information" and would not let me save after i entered the info.
are you starting with a fresh sim? The sim i am using is from the previous owner
matthewjohnunderwood said:
when i rebooted and tried to enter the MIN, MDN etc. it said "Failed to get call NAM information" and would not let me save after i entered the info.
are you starting with a fresh sim? The sim i am using is from the previous owner
Click to expand...
Click to collapse
I'm pretty sure I had to put the SIM back in, program the information, and go into the Data Manager to allow global roaming access.
I was able to get the RAZR MAXX working yesterday following some instructions provided by RemotesquaD (when you purchase their flashing software), and like a big dummy I had it working and tried flashing it with their software so I could get MMS working and it killed the data on the phone. I have sat here the last 4 hours trying to figure it out for this customer, and I am going crazy. I've tried everything, and the only thing I can conceive as a viable reason it won't work is because the phone had been previously activated on Verizon..
Can anyone confirm or deny this? I've tried several 4G SIMs to get through activation and then re-program it to no avail.
If only there was a way to completely revert this phone back to stock, settings and all so I could try from scratch =/ I feel like I might have a country code or SID wrong or something. Any insight would be appreciated! Thanks.
Droid razr maxx
so i followed everyones instructions but i put alittle twist in it i had to use cdma workshop 3.8 free trial and qpst. in cdma workshop alot of stuff didnt write to the phone because you have to buy the version of it so i wrote what i could to the phone and opened up qpst and did the rest with it. my only problem now is i use my wifi in the house and the 3g and 1x indicator is on only on wifi. when i turn wifi off then 3g and 1x goes off also. is it because i have an verizon 4g sim in the phone or is it something with the data?
anyone had any luck getting all this on ics???
---------- Post added at 04:21 PM ---------- Previous post was at 04:19 PM ----------
some info for op
if you flash one of these without the original sim card you might have issues using the ##program# menu.
if you do then here is a tip
get "anycut" from market or search anycut .apk on google
add activity shortcuts one by one to your desktop of the razr
lte test settings
programming (the 2nd one)
testing
field menu settings.
those will give you shortcuts on desktop to enable the setting for 3g.
just had to flash two razrs like this.
hit thanks if it helps
---------- Post added at 04:23 PM ---------- Previous post was at 04:21 PM ----------
another question of mine
has anyone got mms to work without that ugly ass vzw messages app?
ok so i stayed up waaayyy too late last night trying to get my razr on ics with page plus.
i installed the .79 leak and then installed cm9.
it kept all my settings in there that i could see through anycut looking at programming fields.
all i have is talk and text. no mobile data.
i was not able to connect through cdws on cm9 tho. if i reboot with bp tools then it goes to safestrap and after that it shows no diag port in device manager.
just trying to write down everything i did.
about to go back to 181 and maybe start over not sure yet.
deleted
try this for 181
cappii said:
I previously mentioned in the Bionic [Request] thread that the steps for making a RAZR work on PagePlus were the same as a Bionic, however, that statement is not entirely accurate. There is no *#*#4636#*#* on a RAZR, and as such, there seems to be no way at the moment to get 3G data. Picture messaging works if you install VZW messages from the market.
Here is what I did:
First and foremost, use the IMEI but drop the last digit. This is your MEID. Call Pageplus, or find a pageplus dealer who is nice enough to activate it for you, and give them this MEID. You will have to call pageplus cs after you are finished with the following programming to get the MEID put back on the phone. I don't know why this is, and I am not going to give you any kind of technical BS to make it look like I do.
1. Put phone into BP Tools mode by powering off, then pressing both up and down volume and power. Volume down to BP Tools and Volume up to choose it.
2. Install the latest Motorola Driver for your phone from: http://developer.motorola.com/docstools/USB_Drivers/
3. Connect the phone to the PC, and let the driver install complete.
4. Run HW Virtual Serial Port, and login with the password "admin" (it is already there by default, so just hit enter).< no longer necessary
5. Set the IP as 192.168.16.2, with the port as 11008.
6. Choose com port 100.
7. Open CDMA-Workshop 3.7 or higher (There is no known copy floating around for free. Either find someone who has it installed already, or pay the $108 like I did... if you're like me, you'll find ways to recoup your money. I have made it back a few times over already.) Choose COM port and click CONNECT.
8. Click on Security, SPC and send 000000. Do this EVERYTIME you reconnect the phone. Everytime. Don't forget this.
9. Click on Main and go down to where it says CDMA and change it to CDMA-2.
10. Under R-UIM change config to NV Only.
11. Click on the "Other" tab. At PRL, choose write and write the pageplus prl (51720 only) to it. Google for this, it's out there. Write to phone.
12. REBOOT the phone.
13. Reconnect and resend SPC.
14. On the MAIN tab, switch CDMA-2 back to CDMA.
15. Write 310 to MCC, 00 to MNC, and your MIN. Leave True IMSI alone.
16. Write 283, 384 to P CH; and 691 and 777 S CH.
17. Write your mobile number to the DIR_Number and DIR_PCS fields. Write to phone.
18. Change CDMA to EDVO.
19. under PPP User and HDR User write your phone number [email protected], with vzw for the password.
20. under Teth. NAI write your number [email protected].
21. Click on m.ip profiles
22. NAI is the same as 19. T NAI is the same as 20. The shared Secret fields are both VZW.
23. If necessary, change the P. HA address to 255.255.255.255.
24. Click X, then write to phone.
25. Disconnect the phone and reboot it. You are done with CDMA workshop.
26. On your phone, under Settings > wireless and networks > mobile networks > network mode change to CDMA only.
27. Connect to wi-fi and download phone in Play Store (Android Market)
28. Open phone info and go to phone information. Scroll down to set preferred network type and change it to CDMA auto (prl) and toggle DNS Check to allowed.
29. ##Program on your dialer, use "000000" for SPC code, and go to 3> Extended NAM and change the SID to whatever your SID is.
30. Back once to 06 Test Mode, next twice, then make sure network mode is CDMA and EVDO
31. Back once and go to 14 LTE Test Settings. Change SIM Type to 3g, LTE bppanic to disable. Back twice to reboot. Remove SIM Card while rebooting.
32. Back to ##Program 14, disable class1 and class2 APNs and back out. Phone will reboot.
That's it. I have 3g working on 173. Haven't gotten it on 181 or on the ICS leak, though, but, I have a droid razr on my prepaid 29.99/month plan, and couldn't be happier.
Any questions? Please message me. I will respond ASAP.
Please remember to hit the Thanks button if this helps you!!
Click to expand...
Click to collapse
##7764726 lte(14) apn restore using apnpageplus.xml seems to get 1x for a minute...then
sim out--> then disable class 1 apn disable class 2 apn
reboot with sim back in and keep it in
toggle dns check= not allowed
query cfu on powerOn=enabled
instant 3g everytime
Thanks for this pltctytc, but here's a question. I found out that I needed the SIM card kept in to get MMS via VZW Messages. Are you able to get MMS on 3G with the SIM out? The only difference is that my gf's phone is a Bionic on PPC.
had to put sim in to get internet... can't say about mms w/o sim since i didn't try it. i am not using a 4g verizon sim and never had one its a generic h20 one
but everything works as designed sms mms internet email blah blah blah
don't really know if there is a difference but knowing verizon i would assume they have something embedded in their cards
i am really surprised there is so little info about there about the razr or lte phones on pageplus. i guess most using ppc don't want newer phones or their capabilities
nevilles video is good on using cdmaws on the razr but i lost 3g following it but managed getting it back with a couple settings mentioned previously through trial and error
beastmods said:
ok so i stayed up waaayyy too late last night trying to get my razr on ics with page plus.
i installed the .79 leak and then installed cm9.
it kept all my settings in there that i could see through anycut looking at programming fields.
all i have is talk and text. no mobile data.
i was not able to connect through cdws on cm9 tho. if i reboot with bp tools then it goes to safestrap and after that it shows no diag port in device manager.
just trying to write down everything i did.
about to go back to 181 and maybe start over not sure yet.
Click to expand...
Click to collapse
I do have exactly the same issue, it doesn't go to bp tool and directly goes to safestrap after showing red moto logo for few seconds.. I am in stock ICS Rom .. any help, thanks
Sent from my DROID RAZR using Tapatalk 2
lipak said:
I do have exactly the same issue, it doesn't go to bp tool and directly goes to safestrap after showing red moto logo for few seconds.. I am in stock ICS Rom .. any help, thanks
Sent from my DROID RAZR using Tapatalk 2
Click to expand...
Click to collapse
try this
http://www.droidrzr.com/index.php/t...y-17-for-ics-and-those-who-want-to-go-to-ics/
Why is my spc not all zeros when I dial ##PROGRAM? The previous sole user would not be capable of changing it and besides CDMA WS sends 000000 just fine.
I'm trying to unlock the Exhibit 4G this week for use on a trip abroad (and yes, it is legal to do so since this was a prepaid phone paid in full in 2012 so T-Mobile did email me the unlock code - all that is good). What I don't understand is why it is not prompting for the Unlock code at boot. T-Mobile says I must have another company's SIM card in the phone to unlock the Phone. So, I bought a Simple Mobile SIM and placed it in the phone but it just boots up to the ROM as normal without asking for the unlock code. I am using the Linaro 4.2 rom (which is amazing btw!) but I also tried with Peach Sunrise 3.0 and Cyanogen 10 - nothing but a normal boot with no phone capabilities. So I have these questions: Do I actually need to pay for SimpleMobile service first to get the phone to recognize the SIM as different and ask to unlock? (seems unlikely) - Is Simple Mobile just not a good SIM to use for unlocking this phone... Or do I have to go back to stock ROM and unroot to unlock this? Of course if there are any other apps or shortcuts that will let me get straight to the unlock code prompt I'm all for it. Any help is greatly appreciated - not finding a lot of answers out there on the net and if it is on this forum I apologize for not finding it and would appreciate a link to it - Thx!
You probably need a different sim card. As I understand it, T-Mobile phones don't need to be unlocked to work on Simple Mobile.
meekrawb said:
You probably need a different sim card. As I understand it, T-Mobile phones don't need to be unlocked to work on Simple Mobile.
Click to expand...
Click to collapse
Thx - it figures I would choose that one to buy!
Meekrawb is right, simple mobile uses the T-Mobile network.
Sent from my SGH-T679 using xda app-developers app
To get your IMEI go to your cell phone and enter *#06# This will give you a string of numbers you will need to unlock your cell phone. Enter *#06# as if you are going to make a call. Then you will be given the string of numbers you will need.
Sent from my GT-I9300 using xda app-developers app
After you obtain your IMEI and copy it on a piece of paper, power your cell phone off. Take the back off if you have a removable back. Take the SIM card out. Put a BLANK SIM card in its place. Power the cell phone on. A screen should come up asking for your IMEI number to be entered. It should look like a rectangular box. Enter you IMEI. There should be a small box under the rectanglar box that you press. The phone should then eventally unlock itself. You can test it by putting a different SIM card in your cell phone.
Sent from my GT-I9300 using Tapatalk 4 Beta
Hey guys , first of all sorry for my poor English
Im from Taiwan and was attracted by Droid turbo from Verizon
recently, I just got Droid turbo XT1254
it was confirmed that 4G SIM card in Taiwan could work on this phone
however , the first time i plugged my sim card into the phone and powered it on
it just stuck, couldnt input the passward of sim card pin
but the power button and volume button seem to be fine
here is the video
https://www.youtube.com/watch?v=w7e_VnZLDS4
ive tried to fix it in ways
(1)
boot it on without SIM
same consequence, cant slide to unlock to the table
(2)
with SIM card
go to fastboot mode and wait until it shut down
boot it on and the same consequence as well
(3)
without SIM card
go to fastboot mode and wait until it shut down
boot it on and it work!!!
slide to unlock and put in my SIM card
everything works
by the way
ive tried to wipe in recovery mode but remained the same
Is it the problem that i put in NON-Verizon SIM card?
BTW
software version
23.21.44
SU4TL-44
Thx for reading my post and sorry for my poor English again
MOTO Droid turbo is an awesome phone
so im no expert here but if you can put in the official VZW sim and see if that does anything if you can boot into the phone without the sim its a issue with that sim card if you have verizon id suggest calling them idk if you actually need the sim also if you can get into the phone then put the sim back in and you dont get that lock screen again go into settings >More>cellular networks and see if it allows you to change anything id look at preferred network type you have three options Global, LTE/CDMA and LTE/GSM/UMTS mine is on global so try that out and let me know worst case ill look into it for you you may need the unlock code for the phone or something i dont really know
well
i download the latest VRZand flash through mfastboot manaully
it works
All good
Sent from my XT1254 using XDA Free mobile app