Allright hi peps! I have a Cappy in here that was given to me since it wasnt working. Problem is that it seems like the phone have been already taken apart before. The power button is not working and i found out that its been either or pull hard or mishandled and the solder points on the mobo arent there for the power button. I know the one in the middle is just ground. And actually found a soldering point on the motherboard for one of them. So if someone knoows where to find continuity or a soldering point i will be very grateful. Heres a picture of the solder contacts im talking about..
Related
My NC rebooted for reasons of H/W.
Circuit of mini PCB of power button is not shielded, (-) contact and (+) contact are barely opened. And one of those contacts may touch inner metal frame.
I covered bottom of PCB with an insulator(paper), and no more unintended reboot.
I think a gap between PCB contact and metal was enough at first. But when I rooted my NC, exactly pushed power, Vol+ and n button at the same time, the PCB could be misalighed. (PCB is fixed with an adhesive.)
After un-root and factory-reset, reboots still remains, power button may as well be suspected.
unrelated but curious
so let me get this right you have disassembled your nc ?
do you have a guide or make one i have been searching for a guide
and i will probably find one after i post this lol
zdnet.com/photos/nookcolor-teardown/487636?seq=15
referring on this site, you can easily disassemble your NC.
So...I took apart my Nexus One to clean the dust from under the screen. I've done this before, but it back together and it worked. But this time, after putting it back together it wont power on. I sometimes get a vibrate after pressing the power button. One question though. This time I noticed that one end of the coax cable on the left of the phone is broken and there is no plug on it. Would this be the problem? I don't think it should though since I'm guessing it connects the GPS antenna to the rest, and I dont use GPS on my phone. Any help would be good.
EDIT: I think I didnt connect the LCD good enough.
The co ax cable must be connected to the logic board. If it won't click in connect it then secure in place with a small piece of tape.
Hollow.Droid said:
The co ax cable must be connected to the logic board. If it won't click in connect it then secure in place with a small piece of tape.
Click to expand...
Click to collapse
As I said, the top plug of the coax has been ripped off.
Do you know if that's the problem?
Again, when I push the button it vibrates like it usually does on boot, but doesn't show anything on screen.
I pulled out the board again, trying to find the problem.
EDIT!!!! I just noticed on the LCD ribbon cable there are a few bent pins. I think that will be my problem. I'll get it back together in like 15 minutes and report back.
EDIT 2!!!! So yea...two of the pins came off, and are way to small to find. Guess I need to order a new LCD.
Crap, new LCDs are $60+
Hey guys,
The USB port of my HD2 broke off and I was forced to replace the motherboard. When I assembled the HD2 again, I could immediately see that there was something wrong with my screen. The screen couldn't display full color (only bright red/orange/white/dark green/cyan accents). Also, the 'hang-up button isn't responding anymore after I replaced the motherboard (and flexcable).
What happened? Is there something wrong with the lcd display or did something go wrong when I (dis)assembled the phone? I took the motherboard and the flexcable from another HD2 that had a broken display.
Thanks in advance.
bilaba70 said:
Hey guys,
The USB port of my HD2 broke off and I was forced to replace the motherboard. When I assembled the HD2 again, I could immediately see that there was something wrong with my screen. The screen couldn't display full color (only bright red/orange/white/dark green/cyan accents). Also, the 'hang-up button isn't responding anymore after I replaced the motherboard (and flexcable).
What happened? Is there something wrong with the lcd display or did something go wrong when I (dis)assembled the phone? I took the motherboard and the flexcable from another HD2 that had a broken display.
Thanks in advance.
Click to expand...
Click to collapse
So you completely voided your warranty through HTC and tried to fix the device yourself, then screwed it up. I'd still say send it to HTC and ask for a repair. I don't know if they'll do it or not, unless you used official parts. I know they do out-of-warranty repairs, but they'll charge you.....
Yep you screwed up the repair, those ribbon cables need a delicate touch & any handfisted moment ends up with what you have got now ...
Another careful strip & inspection of all ribbon connectors is needed ...
I bought it as a second-hand phone. The guy didn't give me a reseat and the HD2 was flashed a WP7 ROM.
For the button problem, how are you turning your phone on without that button? do you hear/feel it click when you press it? If not its just misaligned.the buttons are on a flex ribbon cable with two holes on each side. it fits on the plastic middle frame of the phone which has two small spikes coming out of it... it has to be perfectly placed for your buttons to actually click..
if the flex ribbon is broken however you can buy one off ebay for arround 10$ any will do, mine is not original works fine..
for the screen you could have messed up the lcd, did you separate from the glass-digitizer? if you did you probably screwed it up.. its not a easy thing to do.. also was not necessary for your repairs
the connection to the motherboard might not be all the in and clipped which might cause your problem... (being that two of the little pins provide voltage and ground while all the others provide data information if one of those pins is not in all the way a piece of data might not be displaying for example a color. Never seen that happen its theoretically possible thou)
well I have only opened my phone 3 times and dont claim to be a expert.. but this is my take on it... Good luck!
@pablow Thanks for the detailed response.
The HD2 is only turned on, after I place the battery. Otherwhise it won't start.
I hear a click on the (broken) 'off' button, everytime I press it. I also noticed that the inside of not all of the 'spikes' are empty. I can see a bit of the flexcable in the spike of the broken 'off' button. The spike of the (working) 'call' button is empty.
I think that the flexcable hasn't been connected securely to the motherboard. I'll try connecting everything again tonight.
not that it makes much difference but HTC wouldn't of fixed it through warranty because of usb damage anyway
I thought so, thanks for the heads-up anyways.
[Solved] Display is fixed
Update:
I disassembled the HD2 and reconnected everything (from coax to flexcable). Fortunately it worked! The display is how it should be.
I have another problem now. All of the buttons don't work now, exept for the dial button. Do these buttons break so fast? It's annoying as fuark, because I have to disassemble it another time in the future to fix the buttons.
I also couldn't re-attach the volume control tab when assembling the HD2.
Hi
I tried to replace my battery and after assemble it back i only get a black display when turning my m7 on.
I broke this little plastic thing from the display cable off (look in attachment)
Is this thing essential for a working display? (i thought i can fix it with a drop of glue)
Should the display work when the backcover is off the device? Because there are some connectors on the backcover....
cheers
00Nuclear00 said:
Hi
I tried to replace my battery and after assemble it back i only get a black display when turning my m7 on.
I broke this little plastic thing from the display cable off (look in attachment)
Is this thing essential for a working display? (i thought i can fix it with a drop of glue)
Should the display work when the backcover is off the device? Because there are some connectors on the backcover....
cheers
Click to expand...
Click to collapse
Shouldn't have done that, I think you accidentally broke something. I'd send it to a HTC service center. But that's gonna cost you probably.
nah, official repair isn't worth it. The phone is more than 2 years old...
and yes i think i broke something... thats why im asking
You're gonna have to be good with a solder and a couple of tiny wires if you want to revive your phone.
00Nuclear00 said:
Hi
I tried to replace my battery and after assemble it back i only get a black display when turning my m7 on.
I broke this little plastic thing from the display cable off (look in attachment)
Is this thing essential for a working display? (i thought i can fix it with a drop of glue)
Should the display work when the backcover is off the device? Because there are some connectors on the backcover....
cheers
Click to expand...
Click to collapse
You definitively need this clip to be intact so the flex cable sits firmly in place otherwise you'll have bad contact between the cable and the pins.
If you don't want to send to HTC for repair you'll need at least to send it to your local electronic repair shop so someone skilled with the proper soldering tool (not the standard iron you have at home) can replace the connector. BTW some of these clips must be lifted from the cable side and some other from the opposite side of the cable, so next time use tweezers and apply very light force on each side you'll find from what side it must be lifted.
LCD should work fine with the back cover removed, afaik. Connectors in the back cover are often for antennas but I wouldn't recommend to run the phone with antennas disconnected to avoid damaging the radio chips (reflected power).
If you are from the US, you can easily find this connector on ebay for about 10$. I'm sure it won't be that much expensive to repair if you bring the new connector and the phone already disassembled to your local repair shop.
Btw are you sure its only the LCD? When trying to boot the phone can you here the HTC theme or does it vibrate? Recognized by your computer when connected with usb?
thx for your response
I found an replacement part on ebay but first i have to look for someone who can solder this for me.
When i try to turn it on it only vibrates without a htc theme sound and there is no display reaction.
The other thing i mentioned is that the phone gets very hot in the middle (should be the cpu) where i dont know if it should get that hot.
I have to try the pc connetion again and let you know asap.
00Nuclear00 said:
thx for your response
I found an replacement part on ebay but first i have to look for someone who can solder this for me.
When i try to turn it on it only vibrates without a htc theme sound and there is no display reaction.
The other thing i mentioned is that the phone gets very hot in the middle (should be the cpu) where i dont know if it should get that hot.
I have to try the pc connetion again and let you know asap.
Click to expand...
Click to collapse
I'm not really worried about the absence of HTC sound when booting, if your phone is on silent / vibration mode, it will only vibrate when booting. If your computer does detect it once booted, then I guess the broken connector clip is the problem.
---------- Post added at 09:49 AM ---------- Previous post was at 09:27 AM ----------
Here is a video about the connector replacement, it doesn't look that hard to replace but wouldn't recommend to do it yourself if you never soldered electronics before. Soldering isn't that hard but you need some practices and knowledge to make good joints. I don't think your phone motherboard is a good candidate to practices yourself if you never did it before. You'll also need a really tiny tip for your iron, probably a type "L", 50/50 solder + some flux. Flux must be cleaned after use to avoid corrosion. The most difficult when soldering on motherboard, imo, is to find the right temperature. If your iron is to hot, you'll damage your connector. If its not hot enough, solder will take more time to liquefy and some heat will be absorbed by surrounding components which can cause irreversible damage.
Easy fix mate
You don't need to replace the connector, I've done this before, it is just the connector clip that has come off and it goes back on reasonably easily.
You will need a good magnifier.
You will need a good light source.
The phone held securely on its side with the socket pointing up.
Some masking tape on the loose part because it WILL go "ping" into the distance if you don't and you will not find it.
Look at the other connectors to see the proper orientation for the part, mark it with a permanent marker on top and at one end.
The insertion looks difficult, it isn't too bad, keep the part nice and straight and the motion is kind of like clicking it down on the ribbon.
Forget replacing the connector, that is 100 times harder.
If you do lose the loose part I have one or two laying around.
Good luck.
Hi guys, while changing the battery of the phone last week, the part you see in the picture was broken. unfortunately the power key is not working. I need to find the part on the motherboard that I circle. Where can I get it? I have to search for this piece.
Bad luck.
Even if you can find that small connector, changing it is going to be very hard. If only you had broken the cable instead - they are usually available as spares, and easier to replace.
I suggest that you look for another broken Nexus, and swap the motherboards.
Looking closely at your picture, it seems that only the plastic guide at the bottom is missing, while the connector itself is intact. Though the picture isn't really sharp enough to tell for sure.
But if that is the case, you should be able to find a way to attach the cable anyway. Align it carefully to the upper guide. And tape it if it seems loose.